EWIKON HPS-C-SLOT+ User's Card Manual

HPS-C-SLOT+ Start Up Procedure

Dry cycle mold 3 – 4 times, apply full tonnage

1

(detects any pinched wires in advance of operation)

Turn “On” main disconnect

2

Select

3

automatic set point
Select Zone 1 , Zone 2
Enter automatic set point
Repeat for other zones or modules

Select

4

automatic/manual mode
Select Zone 1 , Zone 2
Enter “0” for automatic
Repeat for other zones or modules

Select Zone 1

5

Press “Up”

and “Select”

, Zone 2

Apply power to manifolds rst (heat up large mass rst)

Repeat for other zones or modules

Zones will read a low temperature alarm

6

Zones are close or holding set point when the

green temperature holding set point light is illuminated

or “both”

or “both”

. Press enter

. Press enter

or “both”

together (Power “On”)

HPS-C-SLOT+ Controller

Version 1.0 English

Basic Operation / Advanced Setup / Troubleshooting

Thermocouple Open

Thermocouple Pinched

Thermocouple Reversed

Display

Actual Row

Setting Row

Degrees C

Type K Thermocouple

Uncontrolled Output

Open Fuse

Shorted Heater

Open Heater

Alarm Status

Technical information subject to alteration • EWIKON 11/2014 • Item no. 13972E

Automatic set point
Automatic/manual mode

Press “Up” and “Select”
together (Power “On”)

Press “Down” and “Enter”
together (Power “Off”)

Zone select indication

(Press “1” and “2” together to select “both”)

Temperature holding set point (Zone “On”)

Low temperature alarm

EWIKON Heißkanalsysteme GmbH
Siegener Straße 35, 35066 Frankenberg
Tel: [phone] ∙ Fax: [phone]
[e-mail] ∙ www.ewikon.com

Entry Area

Zone Select

Zone

Status

Zone ID

Zone selected

Alarm
High Alarm

Zone “On”
Low Alarm

Manual Mode

Actual Temperature

Actual % Output

Actual Current (Amps)

Automatic/Manual Mode

Manual % Output Set Point

Automatic Set Point

Select

Enter

Increment (Up)

Decrement (Down)

Power “On”

Power “Off”

Standby

Boost

First Zone (Zone 1)

Second Zone (Zone 2)

How to Enter a Set Point How to Select Automatic or Manual Optional Network Module Wiring

Enter Automatic Temperature Set Point

Select zone(s)

1

Select

2

Enter temperature set point

3

Press enter to conrm

4

Automatic set point

Press “Up” or “Down” to adjust tem­perature (Press “Up” and “Down” together

to hange individual digits – 100, 10 or 1)

Select

Enter

Zone select indication

(Press “1” and “2” together

to select “both”)

, or

automatic set point

Select zone(s)

1

Select

2

Enter “0” for automatic or closed loop control

3

Press enter to conrm

4

Enter “1” for manual or open loop control

, or

automatic/manual mode

Automatic/Manual mode

Select

Enter

Zone select

Manual mode light

(No light = automatic mode)

How to Turn the Power “On” & “Off”

Manual % output set point

Zone select

Enter Manual % Output Set Point

Select zone(s)

1

Select

2

Enter manual % set point

3

(0 – 99.9%)

Press enter to conrm

4

, or

manual % output set point

Select

Enter

Turn zone(s) “On”

Select zone(s)

1

Press “Up”

2

together to turn power “On”

Zone(s) “On”

Zone(s) “Off”

Press “1”, “2”, or “1 & 2” together

to select “both”

Turn zone(s) “Off”

Select zone(s)

1

Press “Down”

2

together to turn power “Off”

and “Select”

and “Enter”

, or

, or

4