Evolveo Omega II User Manual

Omega II

www.evolveo.com

Important Safety Instructions

1. Do not use this apparatus near water.

2. Clean only with dry cloth.

3. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

4. Operate this product only from the type of power source indicated on the label. If you are

not sure of the type of power connected to your home, consult your local power company.
Disconnect the unit from the mains before any maintenance or installation procedure.

5. Protect the mains cord from damage and stress.

6. Only use attachments/accessories specified by the manufacturer.

7. Unplug this apparatus during lightning storms or when unused for long periods of time.

8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, including damage to the mains cord or plug, if the unit has
been exposed to liquid or moisture, has been dropped or is not operating correctly.

9. Do not impede the air flow into the unit by blocking the ventilation slots.

10. Attention should be drawn to the environmental aspects of battery disposal.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain

or moisture.

WARNING: The batteries shall not be exposed to excessive heat such as direct sun light, fire,

etc.

This symbol indicates that dangerous voltages constituting a risk of electric shock are
present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

This symbol indicates that this product incorporates double insulation between hazardous
mains voltage and user accessible parts. When servicing use only identical replacement
parts.

This symbol on the product or in the instructions means that your electrical and electronic
equipment should be disposed at the end of life separately from your household waste.
There are separate collection systems for recycling.

For more information, please contact the local authority or your retailer where you
purchased the product.

1. Control Elements

Front Panel

USB Port
CH+/­POWER

Rear Panel

ANT IN
ANT OUT
COAXIAL
HDMI
TV SCART
LAN
DC IN 12V

2. Learning remote control

POWER (Red Button): Standby Mode (ON/OFF)

Fast Backward

Fast Forward

Play/Pause

Stop

REC : Records the TV program to the connected storage device

USB: Enters to the PVR sub menu

SUBTITLE : Displays subtitle options

TTX : Switches on the Teletext

AUDIO : Audio language or Audio mode

EPG : Shows the Electronic Program Guide

INFO : Displays information about the current channel

Move the cursor

MENU : Displays Main Menu

EXIT: Use this button to quit current menu

VOL-/VOL+ : Decrease/ Increase volume

CH-/CH+ : Changing program buttons

FAV : Favorite Channel List

MUTE : Mutes audio output of the receiver

0-9; Numeric buttons

TV/RADIO : Switch between Radio Channels and TV Channels

RECALL : Goes back to previous viewed channel

Smart remote control

•The remote control has 4 programmable buttons for controlling the TV: TV Power, Vol +, Vol-, TV/AV.

•Long press the SET button for 3 seconds, the red LED will be from low light to brighter light, release

the SET button.

•Place the learning and the original remote control from the TV opposite to each other at a distance of
3-5 cm.

•Press and release the learning remote control button you want to program, the red LED will light
blinking.

•Press the button of the original remote control, the LED should blink 2 times and light constantly,
release the button.

•When learning is completed, press the SET button, the LED will turn off.

•Repeat the procedure described above for other functions (buttons) that you want to programme from

your TV control.

This function may not be compatible with all TVs. The manufacturer is not responsible for the compatibility
of this feature with your TV.

BATTERIES INSTALLATION

1. Open the battery compartment cover.

2. Insert 2x AAA batteries with correct polarization.

3. Close the battery compartment cover.

Notes:

Do not mix the batteries.

Remove the batteries if the remote control is not going to be used for an extended period of time.