Thank you for purchasing the EVGA 750T2/850T2/1000T2/1200T2 80PLUS® TITANIUM Rated power supply! The
750T2/850T2/1000T2/1200T2 is designed with the enthusiast in mind, to provide clean, continuous power to every
component. The fully-modular design provides custom cable configurations for any application and due to the
near silent fan the 750T2/850T2/1000T2/1200T2 series reduces heat during heavy load while keeping the decibel
level down. Also, the new ECO Thermal Control switch allows the fan to stop spinning for silent operation when not
needed during low to medium load. The 750T2/850T2/1000T2/1200T2 includes an exceptional 10-year warranty
and has a MTBF rating of 100,000 hours to provide you with peace of mind knowing that your investment is covered
for years to come.
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Safety Information
WARNING1: This unit has no user-serviceable parts inside. Opening the casing presents a risk of electrocution and will void the products
warranty. EVGA will not be responsible for any result of improper use, including but not limited to, any use of the product outside of its intended
purpose or use inconsistent with the warranty terms available online. (Warranty information is available at www.evga.com/support/warranty and
this manual is available at www.evga.com/manuals).
WARNING2: NOT ALL MODULAR CABLES ARE THE SAME OR COMPATIBLE! Use of a non-officially supported cable may void your warranty,
cause a Power Supply failure, and/or cause damage to connected devices. Please use ONLY officially supported cables included with the Power
Supply, or an officially supported set of alternative cables listed for your specific model of Power Supply made BY EVGA. EVGA will NOT be
responsible for damages caused to your power supply, devices, or non-officially supported modular cables in the event damage is caused by
your use of non-officially supported modular cables.
What’s in the Box
Included with your EVGA 750T2/850T2/1000T2/1200T2 power supply offers the following items for proper installation and optional testing:
750T2/850T2 Series1000T2/1200T2 Series
(1) EVGA Power Supply
(1) EVGA Manual
(4) Mounting Screws
(1) EVGA PSU Tester (24-Pin)
(1) EVGA Cable Bag
(1) 24-Pin ATX Cable
(2) 8(4+4)-Pin EPS/ATX12V
CPU Cables
English
(2) 8(6+2)-Pin PCI-E VGA Cables
(2) 6-Pin + 8(6+2)-Pin PCI-E VGA Cables
(2) 3 SATA Cables
(1) 4 SATA Cable
(1) 4 Molex Cable
(1) Molex to FDD Adapter
(1) Power Cord Cable (optional)
(1) EVGA Power Supply
(1) EVGA Manual
(4) Mounting Screws
(1) EVGA PSU Tester (24-Pin)
(1) EVGA Cable Bag
(1) 24-Pin ATX Cable
(2) 8(4+4)-Pin EPS/ATX12V
CPU Cables
2
(4) 8(6+2)-Pin PCI-E VGA Cables
(2) 6-Pin + 8(6+2)-Pin PCI-E
VGA Cables
(3) 4 SATA Cables
(2) 3 Molex Cables
(1) Molex to FDD Adapter
(1) Power Cord Cable (optional)
750W / 850W / 1000W / 1200W TITANIUM
Power Supply User Manual
Features
STABLE POWER
The SuperNOVA TITANIUM series has outstanding electrical performance with ultra stable voltage and extremely
clean power output. This can help you achieve the highest possible overclock (optional) and provide
the most stable and reliable power to all components. The SuperNOVA TITANIUM series also has high effi ciency up
to 94% (115VAC) / 96% (220VAC~240VAC) efficiency and is 80 PLUS TITANIUM certifi ed.
ECO THERMAL CONTROL SYSTEM
The EVGA ECO Intelligent Thermal Control System provides silent operation at low loads, improved effi ciency
and longer life span of the fan. Enabled by a simple switch directly on the power supply, the “No Fan Spin” feature
is ideal for users looking to reduce ambient noise overall. Save on energy costs and unnecessary fan usage with
the EVGA ECO Thermal Control System.
TOP QUALITY PROTECTIONS
The TITANIUM series comes equipped with the most comprehensive protection set possible, including Over Voltage
Protection (OVP), Under Voltage Protection (UVP), Over Power Protection (OPP), Short Circuit Protection (SCP),
Over Current Protection (OCP), Over Temperature Protection (OTP). This product is also covered by an exceptional
10-year warranty and EVGA’s legendary customer service and support.
SUPERIOR BUILD QUALITY
The SuperNOVA TITANIUM series is built to the highest standards, using 100% Japanese capacitors rated at 105
degrees Celsius and high quality brand-name semiconductor components for the highest performance and reliability. The Ultra Quiet 140mm double ball bearing fan provides adequate cooling to allow near silent operation when
not needed and proper cooling during heavy load operation.
MODULAR DESIGN
Reduce clutter in the case, improve ambient temperatures with better airfl ow overall and provide a clean look to
any system. Fully Modular PSU designs allow the user to disconnect the cable from the power supply side if they
are not needed for the specifi c confi guration. This can help free up space inside the case and improve cable
management as well as airfl ow throughout the system. EVGA offers fully modular designs on all T2 series and
include a cable storage bag in case you plan to upgrade or add more components for storage.
Installation
1. Remove the power supply from its packaging.
2. (Optional)Using the provided PSU testing tool, connect the 24-Pin cable to the
PSU, then attach the testing tool to the 24-Pin cable. Connect the ATX power cable
to the PSU and plug the PWR cable into the outlet or surge protector/UPS you plan
to use. Once connected, turn the power switch to the ON position. (If the ECO
mode is set to ON, the fan will not spin)
Please note: If you are using a water cooling configuration, this testing tool
provides a simple, safe, option for bleeding/draining/testing water cooling
components without the need of a paperclip or other device.
3
English
750W / 850W / 1000W / 1200W TITANIUM
3. Use the screws provided with your case to install the power supply
into your computer. NOTE: It is recommended to install the power
supply with the fan facing down. However, if your case places the
power supply at the bottom of the case and there are no ventilation
holes available, it may be best to install the power supply with the
fan facing up for greater effi ciency and reliability.
4. Connect the 24-Pin ATX cable to the PSU and the motherboard.
5. Connect the 4+4-Pin EPS12V cable to the motherboard.
(Optional) – If you plan on extreme overclocking and your
motherboard supports additional 8Pin or 4Pin CPU power
connectors, connect the second 4+4-Pin EPS12V cable. This is
only needed for heavy overclocking or for Dual CPU motherboards.
6. Connect the 6/6+2-Pin PCI-E cables to your graphic card(s).
NOTE: Do not attempt to plug an 8-Pin PCI-E cable into a 6-Pin
connector without fi rst detaching the two extra pins.
7. Connect SATA power cables to all data drives or optical drives.
(hard drives, solid state drives, optical drives)
Power Supply User Manual
8. Connect the peripheral “Molex” 4-Pin connectors for fans, pumps,
legacy components and other devices/adapters.
9. Connect the AC power cord to your power supply and to the wall.
Check all connections to assure a solid connection and turn the
power switch on the power supply to the ON position.
English
4
750W / 850W / 1000W / 1200W TITANIUM
Power Supply User Manual
Q&A
Q: I see there are more than 4 screw holes on the back of the power supply, but the packaging only offers (4)
screws, are some missing?
A: Nothing is missing; you will only need to attach the EVGA power supply to the case with 4 screws. The power
supply offers more than (4) holes to provide optimal compatibility for today’s varied case designs.
Q: My EVGA Power Supply includes (2) EPS cables for my motherboard, do I need to connect up both?
A: Motherboards only require (1) 4+4 or 8-Pin EPS connection, on some models, an additional 4+4-Pin or 8-Pin
connection on the motherboard may be found for dual CPUconfigurations or for extreme overclocking. If your
motherboard support dual 4+4-Pin EPS connections, please refer to your motherboard manufacturer’s manual for
details on the proper function and power if the EPS connections.
Q. What is the ECO Thermal Control System?
A. The ECO Thermal Control System, when enabled, allows the fan on your EVGA power supply to shut off
during low to moderate operation loads. The EVGA power supply’s fan will automatically turn back on when
needed, based on the temperature the power supply reaches. The fan will also increase in RPM when needed,
based on the load operation being requested from the components connected. This prevents unnecessary
rotation, reduces ambient noise levels and will increase the life span of the fan due to the fan not spinning when
not required.
Please Note: If the ECO Thermal Control is disabled the fan will always spin, even at low loads. The fan will also
increase in RPM as needed automatically, based on the power draw from attached components.
Q. What if I want to use power adapters for my video card(s)/motherboard/peripherals?
A. EVGA always recommends the use of direct power connections from the power supply to power the video
card(s), motherboard connections and other auxiliary power connections for optimal power distribution.
Q. Does it matter which end of the cable I plug into the power supply?
A: Yes, the connections going to the power supply, will not have “break downs” like the EPS (CPU) has 4+4 on one
side and full 8-Pin on the other. Another example is the 24-Pin cable, you can see on the PSU side it is a total of
28 Pins, where the 24-Pin connection will go to the motherboard directly. Check each cable as it is labeled
appropriately to match the power supply side and connect only the same ‘‘matching” cable directly to the power
supply as referenced on each connector.
Q. If I have an issue or a question, can I get support?
A: ALL EVGA products are backed by top tier warranties as well as technical support. Support can be reached for
your power supply at:
- USA: +1-888-881-3842 option 1, option 3. or contact us via email at support@evga.com.
- Europe: +49 89 189 049 11 or by email via eu.evga.com/support.
5
English
750W / 850W / 1000W / 1200W TITANIUM
SuperNOVA 750/850T2 Cable Configuration
Modular ConnectorCablesCable Color
MB1 x ATX 24-Pin
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
SATA1
SATA2
SATA3
PERIF11 x Molex 4-Pin x 4
FDD1 x Molex to FDD Adapter
SuperNOVA 750/850T2 Specifications
2 x EPS/ATX12V 8(4+4)-Pin
2 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
2 x SATA 5-Pin x 3
1 x SATA 5-Pin x 4
Black
Power Supply User Manual
SuperNOVA 750W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A62.4A0.5A2.5A
100W748.8W
100-240 VAC, 10A, 60/50 Hz
750W @ +50°C
SuperNOVA 850W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A70.8A0.5A2.5A
100W849.6W
100-240 VAC, 10A, 60/50 Hz
850W @ +50°C
+50°C ambient @ full load
6W12.5W
+50°C ambient @ full load
6W12.5W
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Over Voltage Protection, Under Voltage Protection, Short Circuit Protection, Over Power Protection,
Over Current Protection, Over Temperature Protection.
SATA3
PERIF/SATA2 x Molex 4-Pin x 3
FDD1 x Molex to FDD Adapter
SuperNOVA 1000/1200T2 Specifications
2 x EPS/ATX12V 8(4+4)-Pin
4 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
3 x SATA 5-Pin x 4SATA2
Black
Power Supply User Manual
SuperNOVA 1000W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A83.3A0.5A2.5A
100W999.6W
100-240 VAC, 15A, 60/50 Hz
1000W @ +50°C
SuperNOVA 1200W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A99.9A0.5A2.5A
100W1198.8W
100-240 VAC, 15A, 60/50 Hz
1200W @ +50°C
+50°C ambient @ full load
6W12.5W
+50°C ambient @ full load
6W12.5W
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Over Voltage Protection, Under Voltage Protection, Short Circuit Protection, Over Power Protection,
Over Current Protection, Over Temperature Protection.
Einführung: Leistungsstarke Netzteile einer neuen Generation
Herzlichen Glückwunsch zum Kauf Ihres neuen EVGA 750T2/850T2/1000T2/1200T2 Netzteils mit 80PLUS
TITANIUM-Zertifizierung! Das 750T2/850T2/1000T2/1200T2 Netzteil wurde speziell für anspruchsvolle Anwender
entwickelt und liefert saubere, kontinuierliche Leistung an sämtlichen Systemkomponenten. Das voll-modulare Design
ermöglicht für jedes System die optimale Kabelkonfiguration, und der beinahe lautlose Lüfter der 750T2/850T2/
1000T2/1200T2 Serie sorgt auch bei hoher Auslastung für kühlen, geräuscharmen Betrieb. Durch die
außergewöhnliche 10-Jahres-Garantie und das MTBF-Rating von 100.000 Stunden des 750T2/850T2/1000T2/1200T2
Netzteils können Sie sicher sein, dass Ihre Investition auf Jahre gesichert ist.
®
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Sicherheit
WARNHINWEIS1: Im Gerät befinden sich keine vom Benutzer zu wartenden Teile. Beim Öffnen des Gehäuses besteht das Risiko eines
Stromschlags, und die Produktgarantie verfällt. EVGA übernimmt keinerlei Haftung für Folgen unsachgemäßer Verwendung. Hierzu zählt unter
anderem die Verwendung des Produkts für einen anderen als den vorgesehenen Verwendungszweck oder eine Verwendung, die nicht den online
einsehbaren Garantiebedingungen entspricht. (Die Garantiebedingungen sind auf www.evga.com/support/warranty einsehbar. Dieses Handbuch
ist auf www.evga.com/manuals einsehbar.)
NICHT ALLE MODULAREN KABEL SIND GLEICH ODER KOMPATIBEL! Die Verwendung von nicht offiziell unterstützten
WARNHINWEIS2:
Kabeln kann zum Verlust der Garantie, einem Ausfall des Netzteils und/oder zu einem Schaden der verbundenen Hardware führen. Bitte
verwenden Sie ausschließlich offiziell unterstützte Kabel aus dem Lieferumfang oder ein offiziell unterstütztes Kabelset von EVGA speziell für Ihr
Netzteil. EVGA haftet nicht für Schäden an Ihrem Netzteil inkl. Kabeln und sonstigen Geräten, verursacht durch die Verwendung von nicht offiziell
unterstützten modularen Kabeln.
Lieferumfang
Im Lieferumfang des EVGA 750T2/850T2/1000T2/1200T2 Netzteils sind folgende Komponenten für die korrekte
Installation und optionale Funktionstests enthalten:
Die TITANIUM-Serie liefert hervorragende elektrische Leistung mit extra stabilen Spannung und extrem
sauberem Output. Sie ermöglicht maximale Übertaktung (sofern erwünscht) und versorgt sämtliche Komponenten
zuverlässig mit stabiler Leistung. Die SuperNOVA TITANIUM Serie bietet eine ausgezeichnete Effi zienz mit mehr als
94% (115VAC) / 96% (220VAC~240VAC) und ist 80 PLUS TITANIUM zertifi ziert.
ECO THERMAL CONTROL SYSTEM
Das EVGA ECO Intelligent Thermal Control System sorgt für leiseren Betrieb bei geringerer Auslastung,
verbesserte Effi zienz und eine längere Lebensdauer des Lüfters. Die über einen einfachen Schalter direkt am
Netzteil aktivierbare “No Fan Spin“ Funktion ist ideal, um den Geräuschpegel zu senken. Das EVGA ECO Thermal
Control System reduziert die Energiekosten und vermeidet überfl üssigen Lüfterbetrieb.
ERSTKLASSIGE SCHUTZMERKMALE
Die TITANIUM-Serie verfügt über umfangreiche Schutzmerkmale, darunter Überspannungsschutz (Over Voltage
Protection, OVP), Unterspannungsschutz (Under Voltage Protection, UVP), Überlastschutz (Over Power Protection,
OPP), Kurzschlussschutz (Short Circuit Protection, SCP) und Überstromschutz (Over Current Protection, OCP),
Überhitzungsschutz (Over Temperature Protection, OTP). Noch mehr Sicherheit bieten zudem die
außergewöhnliche 10-Jahres-Garantie sowie der legendäre EVGA Kundendienst und Support.
HERVORRAGENDE QUALITÄT
Die T2-Serie entspricht den höchsten Baustandards. Verbaut werden ausschließlich japanische Kondensatoren
mit einer maximalen Betriebstemperatur bis zu 105 °C, sowie hochwertige Halbleiterkomponenten namhafter
Hersteller für maximale Leistung und Zuverlässigkeit. Der ultraleise 140 mm Lüfter mit doppeltem Kugellager
sorgt für leise Kühlung, beinahe lautlosen Betrieb bei geringer Belastung und für eine zuverlässige Kühlung bei
hoher Belastung.
MODULARES DESIGN
Das aufgeräumte, übersichtliche Innere des PC-Gehäuses ermöglicht niedrigere Temperaturen durch
verbesserten Luftstrom. Durch das voll-modulare Netzteil-Design können die Kabel vom Netzteil abgetrennt
werden, wenn sie für die jeweilige Konfi guration nicht benötigt werden. Dadurch kann mehr Raum im PC-
Gehäuse genutzt, die Kabelführung verbessert und der Luftstrom im System optimiert werden.Alle Modelle der
T2-Serie sind modular und umfassen einen praktischen Beutel für die Kabelaufbewahrung, falls Sie später ein
Upgrade planen oder weitere Komponenten hinzufügen möchten.
Installation
1. Entnehmen Sie das Netzteil aus der Verpackung.
2. (Optional) Schließen Sie das 24-Pin-Kabel an das Netzteil und anschließend an
den mitgelieferten Netzteil-Tester an. Schließen Sie das ATX-Stromkabel an das
Netzteil an und schließen Sie das PWR-Kabel an die beabsichtigte Buchse bzw.
dem Überspannungsschutz/Netzausfallschutz an. Schalten Sie anschließend den
Netzschalter in die Stellung EIN “I”.
Bitte beachten: Bei Konfigurationen mit Wasserkühlung stellt der Tester
eine einfache und sichere Methode zum Entlüften/Ablassen/Testen der
Komponenten der Wasserkühlung dar, ohne eine Büroklammer oder
Ähnliches zu Hilfe nehmen zu müssen.
Deutsch
10
750W / 850W / 1000W / 1200W TITANIUM
Netzteil Bedienungsanleitung
3. Verwenden Sie die mitgelieferten Schrauben, um das Netzteil im Computer
zu anzubringen. HINWEIS: Es wird empfohlen, das Netzteil mit dem Lüfter
nach unten zu installieren. Hat das Gehäuse unten jedoch keine Lüftungss
chlitze ist es effi zienter das Netzteil an einer Stelle mit Lüftungsschlitzen
anzubringen, um mehr Zuverlässigkeit und Kühlung zu gewährleisten.
4. Schließen Sie das 24-Pin ATX-Kabel an das Netzteil und das
Mainboard an.
5. Schließen Sie das 4+4-Pin EPS12V-Kabel an das Netzteil und das Main
board an. (Optional) – Wenn Sie extremes Übertakten beabsichtigen
und Ihr Mainboard zusätzliche 8-Pin oder 4-Pin CPU-Netzstecker unter
stützt, schließen Sie das zweite 4+4-Pin EPS12V-Kabel an. Dieses Kabel
wird nur für extremes Übertakten und für Mainboards mit zwei CPUs
benötigt.
6. Schließen Sie die 6/6+2-Pin PCI-E-Kabel an Ihre Grafi kkarte(n) an.
HINWEIS: Versuchen Sie nicht, ein 8-Pin PCI-E-Kabel an einen 6-Pin Anschluss anzuschließen, ohne zuvor die zwei zusätzlichen Pins entfernt
zu haben.
7. Schließen Sie die SATA-Netzkabel an alle Datenlaufwerke und optischen
Laufwerke an. (Mainboards, Solid-State-Laufwerke (SSDs), optische
Laufwerke)
8. Schließen Sie die peripheren “Molex” 4-Pin-Stecker für Lüfter, Pumpen,
ältere Komponenten und sonstige Geräte/Adapter an.
9. Schließen Sie das Netzkabel an das Netzteil und Steckdose an. Überprüfen
Sie sämtliche Anschlüsse auf sicheren Sitz und schalten Sie den
Netzschalter am Netzteil in die Stellung EIN “I”.
11
Deutsch
750W / 850W / 1000W / 1200W TITANIUM
Netzteil Bedienungsanleitung
Häufige Fragen
F: An der Rückseite des Netzteils gibt es mehr als 4 Schraubenlöcher, aber in der Packung sind nur (4)
Schrauben enthalten. Fehlen weitere Schrauben?
A: Nein, es fehlt nichts. Das EVGA Netzteil braucht nur mit 4 Schrauben im Gehäuse befestigt zu werden. Das
Netzteil verfügt über mehr als (4) Löcher, um optimale Kompatibilität mit unterschiedlichen Gehäusedesigns zu
gewährleisten.
F: Mein EVGA Netzteil verfügt über (2) EPS-Kabel für das Mainboard. Muss ich beide anschließen?
A: Die meisten aktuellen Mainboards erfordern nur (1) 4+4 oder 8-Pin EPS-Anschluss. Manche Mainboards
verfügen über einen zusätzlichen 4+4-Pin-Anschluss für Konfi gurationen mit zwei CPUs oder für extremes
Übertakten. Wenn Ihr Mainboard zwei 4+4-Pin EPS-Anschlüsse unterstützt, informieren Sie sich im
Herstellerhandbuch Ihres Mainboards über die Funktion und Spannung der EPS-Anschlüsse.
F: Was ist das ECO Thermal Control System?
A: Ist das ECO Thermal Control System aaktiviert, kann es dafür sorgen, dass sich der Lüfter bei niedriger und
bei mittlerer Arbeitslast nicht dreht. Bei Bedarf schaltet sich der Lüfter des EVGA Netzteils automatisch wieder
ein, wenn das Netzteil eine bestimmte Temperatur erreicht. Je nach Auslastung der angeschlossenen Kompo-
nenten kann der Lüfter bei Bedarf auch die Drehzahl steigern. Die Vermeidung überfl üssiger Aktivität senkt den
Geräuschpegel und steigert die Lebensdauer des Lüfters.
Bitte beachten: Wenn ECO Thermal Control deaktiviert ist, dreht sich der Lüfter immer, auch bei geringer
Auslastung. Je nach Leistungsaufnahme der angeschlossenen Komponenten wird die Drehzahl des Lüfters
automatisch gesteigert.
F. Kann ich auch Adapter verwenden, um meine Grafi kkarte(n), Mainboard oder andere Komponenten
anzuschließen?
A. Für eine optimal ausgewogene Stromversorgung empfi ehlt EVGA direkte Verbindungen vom Netzteil zur
Grafi kkarte, zum Mainboard und zu anderen Komponenten. Adapter sollten nur verwendet werden, wenn es gar
keine andere Möglichkeit gibt.
F. Macht es einen Unterschied, welches Kabelende in das Netzteil eingesteckt wird?
A: Ja, denn die Stecker auf der Netzteilseite sind nicht unterteilt. Beispiel: Das EPS-Kabel für die CPU hat auf der
Netzteilseite einen 8-Pin-Anschluss und auf der anderen Seite einen 4+4-Anschluss. Ein weiteres Beispiel ist das
24-Pin-Kabel: an der Netzteilseite verfügt es über insgesamt 28 Pins, während sich auf der Mainboardseite ein
direkter 24-Pin-Anschluss befi ndet. Überprüfen Sie die Beschriftung sämtlicher Kabel, um sicherzustellen, dass
immer das korrekte Ende am Netzteil angeschlossen wird.
Alle EVGA Produkte verfügen über erstklassige Garantien und 24h-Kundendienst. So erreichen Sie den
Kundendienst für Ihr Netzteil:
- USA: unter 888-881-3842
- Europa: unter +49 89 189 049 11
Deutsch
Option 1, Option 3 oder per E-Mail an support@evga.com.
oder per E-Mail an eu.evga.com/support.
12
750W / 850W / 1000W / 1200W TITANIUM
Netzteil Bedienungsanleitung
SuperNOVA 750/850T2 Kabelkonfiguration
Modular ConnectorKabelKabel Farbe
MB1 x ATX 24-Pin
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
SATA1
SATA2
SATA3
PERIF11 x Molex 4-Pin x 4
FDD1 x Molex to FDD Adapter
SuperNOVA 750/850T2 Spezifikationen
2 x EPS/ATX12V 8(4+4)-Pin
2 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
2 x SATA 5-Pin x 3
1 x SATA 5-Pin x 4
Schwarz
SuperNOVA 750W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A62.4A0.5A2.5A
100W748.8W
100-240 VAC, 10A, 60/50 Hz
750W @ +50°C
SuperNOVA 850W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A70.8A0.5A2.5A
100W849.6W
100-240 VAC, 10A, 60/50 Hz
850W @ +50°C
+50°C ambient @ full load
6W12.5W
+50°C ambient @ full load
6W12.5W
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Darunter: Überspannungsschutz, Unterspannungsschutz, Überlastschutz, Kurzschlussschutz,
Überstromschutz, Überhitzungsschutz.
13
Deutsch
750W / 850W / 1000W / 1200W TITANIUM
SuperNOVA 1000/1200T2 Kabelkonfiguration
Netzteil Bedienungsanleitung
Modular ConnectorKabel
Kabel Farb
e
MB1 x ATX 24-Pin
CPU1
CPU2
2 x EPS/ATX12V 8(4+4)-Pin
VGA1
VGA2
VGA3
VGA4
VGA5
4 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
Schwarz
VGA6
SATA1
3 x SATA 5-Pin x 4SATA2
SATA3
PERIF/SATA2 x Molex 4-Pin x 3
FDD1 x Molex to FDD Adapter
SuperNOVA 1000/1200T2 Spezifikationen
SuperNOVA 1000W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A83.3A0.5A2.5A
100W999.6W
100-240 VAC, 15A, 60/50 Hz
1000W @ +50°C
SuperNOVA 1200W TITANIUM
AC Input
DC Output+5V+3.3V+12V-12V+5Vsb
MAX output, A
Combined, W
Output power,
Pcont
20A20A99.9A0.5A2.5A
100W1198.8W
100-240 VAC, 15A, 60/50 Hz
1200W @ +50°C
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Darunter: Überspannungsschutz, Unterspannungsschutz, Überlastschutz, Kurzschlussschutz,
Überstromschutz, Überhitzungsschutz.
Gracias por comprar la Fuente de poder EVGA 750T2/850T2/1000T2/1200T2 80PLUS! está diseñado con la mente
entusiasta, para proporcionar energía limpia y continua en todos los componentes. El diseño totalmente modular
ofrece confi guraciones de cables personalizadas para cualquier aplicación y debido al ventilador silencioso cerca
de la serie 750T2/850T2/1000T2/1200T2 reduce el calor durante la carga pesada mientras se mantiene el nivel de
decibelios abajo. 750T2/850T2/1000T2/1200T2 incluye una garantía excepcional de 10 años y tiene un MTBF de
100.000 horas para ofrecerle la tranquilidad de saber que su inversión está cubierta para los próximos años.
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Información de seguridad
ADVERTENCIA1: Esta unidad no tiene piezas que el usuario pueda reparar. La apertura de la cubierta representa un riesgo de descarga eléctrica
y anulará la garantía de los productos. EVGA no será responsable por cualquier resultado de mal uso, incluyendo pero no limitado a, cualquier
uso del producto fuera de su finalidad o uso inconsistente con los términos de la garantía disponibles en línea. (Información sobre la garantía
está disponible en www.evga.com/support/warranty y este manual está disponible en www.evga.com/manuals).
NO TODOS LOS CABLES MODULARES SON IGUALES O COMPATIBLES. El uso de cables no soportados oficialmente
ADVERTENCIA2:
puede invalidar su garantía, causar un fallo de la fuente de poder y/o causar daño a los componentes conectados. Por favor utiliza solo los
cables oficialmente soportados incluidos en tu fuente de poder, o un set alternativo de cables oficialmente soportado por EVGA para tu modelo
especifico de fuente de poder. EVGA no se hace responsable por daños causados a tu fuente de poder, componentes o cables no soportados
oficialmente en el evento de un daño causado por el uso de cables no soportados oficialmente.
¿Qué hay en la caja?
Incluido con su fuente de alimentación EVGA 750T2/850T2/1000T2/1200T2 ofrece los siguientes artículos para su
correcta instalación y pruebas opcionales:
750T2/850T2 Series1000T2/1200T2 Series
(1) EVGA Fuente de Poder
(1) EVGA Manual
(4) Tor nillos de Montaje
(1) EVGA PSU Tester (24-Pin)
(1) EVGA Bolsa de Cable
(1) Cable ATX de 24-Pines
(2) Cable EPS/ATX para CPU
8(4+4)-Pines de 12V
Español
(2) Cables 8(6+2)-Pines PCI-E VGA
(2) Cables 6-Pines + 8(6+2)-Pines
PCI-E VGA
(2) Cables para 3 SATA
(1) Cable para 4 SATA
(1) Cable para 4 Molex
(1) Cable Adaptador Molex para FDD
(1) Cable de alimentación (opcional)
(1) EVGA Fuente de Poder
(1) EVGA Manual
(4) Tor nillos de Montaje
(1) EVGA PSU Tester (24-Pin)
(1) EVGA Bolsa de Cable
(1) Cable ATX de 24-Pines
(2) Cables EPS/ATX para CPU
8(4+4)-Pines de 12V
(4) Cables 8(6+2)-Pines PCI-E VGA
16
(2) Cables 6-Pines +
8(6+2)-Pines PCI-E VGA
(3) Cables para 4 SATA
(2) Cables para 3 Molex
(1) Cable Adaptador Molex
para FDD
(1) Cable de alimentación
(opcional)
Manual de Usuario Fuente de Poder
750W / 850W / 1000W / 1200W TITANIUM
Características
ENERGÍA ESTABLE
La serie TITANIO tiene un rendimiento eléctrico excepcional con voltaje ultra estable y potencia extremadamente
limpio. Esto puede ayudarle a alcanzar el máximo overclock (opcional) y proporciona la potencia más estable y
confi able para todos los componentes. La serie SuperNOVA TITANIO también tiene una alta efi ciencia superior al
94% (115VAC) / 96% (220VAC~240VAC) eficiencia y es la certifi cación 80 PLUS TITANIO.
ECO THERMAL CONTROL SYSTEM
El sistema inteligente de control Térmico EVGA ECO, proporciona un funcionamiento silencioso a baja carga, la
mejora de efi ciencia prolonga la vida útil del ventilador. Activado por un simple interruptor directamente en la
fuente de alimentación “No Fan Spin” característica ideal para usuarios que buscan reducir el ruido del ambiente
en general. Ahorre costos de energía en del consumo innecesario del ventilador con el Sistema Dual de Control
Térmico EVGA ECO.
PROTECCIONES DE PRIMERA CALIDAD
La serie TITANIO viene equipado con la más completa protección ajustado posible, incluyendo Protección de
sobre voltaje (Over Voltage Protection, OVP), bajo la protección del voltaje (Under Voltage Protection, UVP), sobre
la protección de energía (Over Power Protection, OPP), protección contra cortocircuitos (Short Circuit Protec-
tion, SCP), Over Protección de corriente (Over Current Protection, OCP), Protección Contra Altas Temperaturas
(Over Temperature Protection, OTP). Este producto también está cubierto por una garantía de 10 años de servicio
soporte al cliente excepcional y legendario de EVGA.
CALIDAD DE CONSTRUCCIÓN SUPERIOR
La serie T2 está construida con los más altos estándares, utilizando 100% condensadores japoneses nominal de
105 grados Celsius y de alta calidad de marca de componentes de semiconductores para el más alto rendimiento
y fi abilidad. El Ultra Silencioso 140mm de doble bola ventilador teniendo proporciona una refrigeración adecuada
para permitir un funcionamiento casi silencioso cuando no es necesario y el enfriamiento adecuado durante la
operación de carga pesada.
DISEÑO MODULAR
Reduzca el desorden en el caso, mejorar la temperatura ambiente con un mejor fl ujo de aire en general y
proporcionar una apariencia limpia a cualquier sistema. Diseños de Fuentes de Poder totalmente modulares
permiten que el usuario desconecte el cable del lado de la alimentación si no son necesarios para la confi guración
específi ca. Esto puede ayudar a liberar espacio dentro de la caja y mejorar la gestión de los cables, así como el
fl ujo de aire a través del sistema.
Instalación
1. Retire la fuente de alimentación de su embalaje.
2. (Opcional) Uso de la herramienta de prueba PSU proporcionado, conecte el cable de
24-Pines de la fuente de alimentación, a continuación, coloque la herramienta de prueba
al cable de 24-Pines. Conecte el cable de alimentación ATX de la fuente de alimentación
y enchufe el cable de PWR en el tomacorriente o protector/UPS que planea usar contra
sobretensiones. Una vez conectado, gire el interruptor de encendido en la posición ON.
Nota: Si está utilizando una configuración de enfriamiento por agua, esta
herramienta proporciona una prueba simple, seguro, la opción de sangrado/
drenaje/ensayo de componentes de refrigeración de agua sin la necesidad de un
clip u otro dispositivo.
17
Español
Manual de Usuario Fuente de Poder
750W / 850W / 1000W / 1200W TITANIUM
3. Utilice los tornillos suministrados con el caso de instalar la fuente de
alimentación en el equipo. NOTA: Se recomienda la instalación de la
fuente de alimentación con el ventilador hacia abajo. Sin embargo, si su
caso coloca la fuente de alimentación en la parte inferior de la caja y no
hay orifi cios de ventilación disponibles, puede ser mejor instalar la fuente
de alimentación con el ventilador hacia arriba para una mayor efi ciencia
y fi abilidad.
4. Conecte el cable ATX de 24-Pines de la fuente de alimentación y la placa
madre.
5. Conecte el cable EPS12V 4+4 clavijas de la fuente de alimentación y la
placa madre. (Opcional) - Si usted planea en overclocking extrema y su
placa base soporta 8-Pines adicionales o conectores de alimentación de
CPU 4-Pines, conecte el segundo cable EPS12V 4+4-Pines. Esto sólo es
necesario para el overclocking pesada o para placas base duales CPU.
6. Conecte los cables 6/6+2-Pines PCI-E para la tarjeta gráfi ca(s).
NOTA: No intente conectar un cable de 8-Pines PCI-E en un conector
de 6-Pines sin primero desmontar los dos pines adicionales.
7. Conecte los cables de alimentación SATA a todas las unidades de datos
o unidades ópticas. (discos duros, unidades de estado sólido, unidades
ópticas)
8. Conecte los conectores periféricos “Molex“ 4-Pines para ventiladores,
bombas, componentes heredados y otros dispositivos/adaptadores.
9. Conecte el cable de alimentación de CA a la fuente de aliment
ación y en la pared. Revise todas las conexiones para asegurar
una conexión sólida y gire el interruptor de encendido de la fuente
de alimentación a la posición ON.
Español
18
Manual de Usuario Fuente de Poder
750W / 850W / 1000W / 1200W TITANIUM
Q&A
Q: Veo que hay más de 4 orifi cios para tornillos de la parte posterior de la fuente de alimentación, pero el envase
sólo ofrece (4) tornillos, es un poco de falta?
R: No le falta nada, sólo se tendrá que conectar la fuente de alimentación EVGA a la caja con 4 tornillos. La fuente
de alimentación dispone de más de (4) orifi cios para proporcionar una compatibilidad óptima para los diseños de
caso en la actualidad.
Q: Mi EVGA incluye fuente de alimentación (2) cables EPS para mi madre, tengo que conectar las dos cosas?
A: Placas base sólo requieren (1) 4+4 o 8-Pines EPS conexión, en algunos modelos, un 4+4-Pines de conexión
adicional en la placa base se pueden encontrar para confi guraciones de doble CPU o de extrema overclocking .
Si su placa base de apoyo de doble 4+4 conexiones EPS perno, consulte el manual de fabrica motherboard para
obtener información sobre la función y el poder adecuado si las conexiones EPS.
Q: ¿Qué pasa si quiero usar adaptadores de corriente para mi tarjeta de video(s)/placa base/periféricos?
A: El sistema de control térmico ECO, cuando está activado, permite que el ventilador de la fuente de alimentación
a EVGA no gira durante bajas a moderadas cargas de operación. Ventilador de la fuente de alimentación EVGA
se volverá a encender automáticamente cuando sea necesario, sobre la base de la temperatura de los alcances
de suministro de energía. El ventilador también aumentará en RPM, cuando sea necesario, sobre la base de la
operación de carga que se solicita de los componentes conectados. Esto evita la rotación innecesaria, reduce los
niveles de ruido ambiente y aumentará la vida útil del ventilador debido a que el ventilador no gira cuando no es
necesario.
Nota: Si el control térmico ECO se desactiva el ventilador siempre estará girando, incluso a bajas cargas. El
ventilador también aumentará en el RPM, según sea necesario de forma automática, en función del consumo de
energía de los componentes conectados.
Q: ¿Qué pasa si quiero usar adaptadores de corriente para mi tarjeta(s) de vídeo/placa base/periféricos?
A: EVGA recomienda el uso de conexiones de alimentación directa de la red eléctrica para alimentar la tarjeta
de video(s), las conexiones de la placa base y el resto de las conexiones de potencia auxiliar para la distribución
óptima de la energía.
Q: ¿Es importante que los extremos del cable que se conectan a la fuente de alimentación?
A: Sí, las conexiones que van a la fuente de alimentación, no tendrán “averías“, como el EPS (CPU) tiene 4+4
en un lado y lleno de 8-Pines en el otro. Otro ejemplo es el cable de 24-Pines, se puede ver en el lado PSU se
trata de un total de 28-Pines, donde la conexión de 24-Pines irá directamente a la placa base. Compruebe cada
cable a medida que se etiquete de forma apropiada para que coincida con el lado de la fuente de alimentación y
conectarse sólo el mismo cable “coincidencia“ directamente a la fuente de alimentación como se indica en cada
conector.
Q: ¿Si tengo un problema o una pregunta, ¿puedo obtener ayuda?
A: Todos los productos de EVGA están respaldados por garantías tom nivel, así como apoyo técnico.
El apoyo puede ser contactado para la fuente de alimentación al 888-881-3842 opción 1, opción 3 o póngase en
contacto con nosotros por correo electrónico a support@evga.com.
19
Español
Manual de Usuario Fuente de Poder
750W / 850W / 1000W / 1200W TITANIUM
SuperNOVA 750/850T2 configuración de cables
Conectores ModularesCablesColor de Cable
MB1 x ATX 24-Pin
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
SATA1
SATA2
SATA3
PERIF11 x Molex 4-Pin x 4
FDD1 x Molex to FDD Adapter
SuperNOVA 750/850T2 especificaciones
2 x EPS/ATX12V 8(4+4)-Pin
2 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
2 x SATA 5-Pin x 3
1 x SATA 5-Pin x 4
Negro
SuperNOVA 750W TITANIUM
Entrada de CA
Salida de DC+5V+3.3V+12V-12V+5Vsb
Maxima salida, A
Combinada, W
Potencia de
salida, Pcont
20A20A62.4A0.5A2.5A
100W748.8W
100-240 VAC, 10A, 60/50 Hz
750W @ +50°C
SuperNOVA 850W TITANIUM
Entrada de CA
Salida de DC+5V+3.3V+12V-12V+5Vsb
Maxima salida, A
Combinada, W
Potencia de
salida, Pcont
20A20A70.8A0.5A2.5A
100W849.6W
100-240 VAC, 10A, 60/50 Hz
850W @ +50°C
+50°C de temperatura
ambiente a plena carga
6W12.5W
+50°C de temperatura
ambiente a plena carga
6W12.5W
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Protección de sobre voltaje, Protección ante bajo voltaje, Protección de sobrecarga de energía, Protección
contra cortocircuito, Protección de sobrecarga de corriente, Protección Contra Altas Temperaturas.
Nous vous Nous vous remercions de l’achat du bloc d’alimentation EVGA 750T2/850T2/1000T2/1200T2 80PLUS
TITANIUM Rated! Le bloc d’alimentation 750T2/850T2/1000T2/1200T2 a été conçu en pensant aux utilisateurs
enthousiastes,dans le but d’alimenter tous les composants en continu. La conception entièrement-modulaire permet
de réaliser des configurations de câbles personnalisées pour toutes les applications. Grâce au ventilateur quasiment
silencieux,la série 750T2/850T2/1000T2/1200T2 émet également peu de chaleur lorsque les charges sont élevées et
génère un faible niveau sonore. Le bloc d’alimentation 750T2/850T2/1000T2/1200T2 bénéficie d’une garantie
exceptionnelle de dix ans et dispose d’un temps moyen entre défaillances de 100,000 heures, vous pouvez ainsi être
rassuré à l’idée que votre investissement est couvert pour les années à venir.
®
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Consignes de sécurité
AVERTISSEMENT1:
cet appareil ne contient pas de pièces que l’utilisateur peut réparer. L’ouverture du boîtier présente un risque d’électrocution
et annulera la garantie du produit. La société EVGA ne peut être tenue responsable des conséquences d’une utilisation incorrecte, ce qui inclut,
sans s’y limiter, l’utilisation du produit dans un but autre que celui prévu ou l’utilisation non conforme aux conditions de garantie disponibles en
ligne. (La garantie est disponible sous www.evga.com/support/warranty et le manuel sous www.evga.com/manuals).
AVERTISSEMENT2:
TOUS LES CÂBLES MODULAIRES NE SONT PAS LES MEMES ET NE SONT PAS COMPATIBLE! L'utilisation d'un câble
non officielle pris en charge peut annuler la garantie, provoquer une panne d'alimentation, et / ou causer des dommages aux appareils
connectés. S'il vous plaît utiliser uniquement des câbles officiels pris en charge inclus avec le bloc d'alimentation, ou un ensemble officiellement
pris en charge des câbles alternatifs listés pour votre modèle d’alimentation faite PAR EVGA. EVGA ne sera pas responsable des dommages
causés à votre alimentation dans le cas d’une utilisation d’un dispositifs ou câbles modulaires non compatible.
Contenu de la boîte
Les éléments suivants sont fournis avec le bloc d’alimentation EVGA 750T2/850T2/100T2/1200T2 pour garantir
une installation correcte et pour effectuer des tests en option:
750T2/850T2 Series1000T2/1200T2 Series
(1) Alimentation EVGA
(1) Manuel EVGA
(4) Vis de montage
(1) Testeur PSU EVGA
(24 broches)
(1) Sac pour câble EVGA
(1) Câble 24 broches ATX
(2) Câbles 8(4+4) broches
EPS/ATX12V CPU
(2) Câbles 8(6+2) broches PCI-E VGA
(2) Câbles 6 broches + 8(6+2) broches
PCI-E VGA
(2) Câbles 3 SATA
(1) Câble 4 SATA
(1) Câble 4 Molex
(1) Adaptateur Molex vers lecteur de
disquette
(1) Cordon d’alimentation (en option)
(1) Alimentation EVGA
(1) Manuel EVGA
(4) Vis de montage
(1) Testeur PSU EVGA (24 broches)
(1) Sac pour câble EVGA
(1) Câble 24 broches ATX
(2) Câbles 8(4+4) broches EPS/
ATX12V CPU
(4) Câbles 8(6+2) broches PCI-E VGA
23
(2) Câbles 6 broches +
8(6+2) broches PCI-E VGA
(3) Câbles 4 SATA
(2) Câbles 3 Molex
(1) Adaptateur Molex vers
lecteur de disquette
(1) Cordon d’alimentation
(en option)
Français
Manuel d’utilisation. Alimentation
750W / 850W / 1000W / 1200W TITANIUM
Fonctionnalités
ALIMENTATION STABLE
La série TITANIUM offre des performances électriques exceptionnelles avec une tension ultra stable et des sorties
extrêmement propres. Cela vous permet d’obtenir l’overclocking le plus élevé possible (facultatif) et d’alimenter
tous les composants de manière stable et fi able. La série SuperNOVA TITANIUM est certifi ée 80 PLUS TITANIUM,
avec un rendement de plus de efficacité de 94% (115VAC) / 96% (220VAC~240VAC) maximum.
Système de commande thermique ECO
Le système de commande thermique intelligent ECO EVGA assure le fonctionnement silencieux lorsque les
charges sont faibles, pour une plus grande effi cacité et une plus longue durée de vie du ventilateur. La
fonctionnalité No Fan Spin, activée à l’aide d’un interrupteur situé sur le bloc d’alimentation, est parfaite pour les
utilisateurs qui souhaitent réduire le bruit ambiant global. Réalisez des économies sur les coûts d’énergie et
utilisez le ventilateur uniquement lorsque cela est nécessaire avec le système de commande thermique ECO EVGA.
PROTECTIONS OPTIMALES
La série TITANIUM est équipée de l’ensemble de protection le plus complet possible: protection contre la surtension
(Over Voltage Protection, OVP), protection contre la sous-tension (Under Voltage Protection, UVP), protection
contre la surpuissance (Over Power Protection, OPP), protection contre les courts-circuits (Short Circuit Protection,
SCP) et protection contre la surintensité (Over Current Protection, OCP), Protection contre la surchauffe (Over Tem-
perature Protection, OTP). Ce produit bénéfi cie également d’une garantie exceptionnelle de dix ans et de la qualité
légendaire de l’assistance et du service clientèle de la société EVGA.
QUALITÉ DE FABRICATION SUPÉRIEURE
La série T2 est fabriquée selon les normes les plus strictes, avec des condensateurs 100 % japonais d’une valeur
nominale de 105°C et des semi-conducteurs de marque de grande qualité pour des performances et une fi abilité
optimales. Le ventilateur de 140 mm extrêmement silencieux à double roulement à billes fonctionne de manière
presque silencieuse lorsqu’il n’est pas nécessaire et un refroidissement adapté lorsque les charges sont élevées.
CONCEPTION MODULABLE
Libérez de l’espace dans le boîtier, améliorez les températures ambiantes avec un fl ux d’air global optimisé et
donnez à votre système un aspect rangé. La conception d’unité centrale entièrement modulable permet à l’utilisateur
de débrancher le câble du côté du bloc d’alimentation s’il n’est pas nécessaire pour la confi guration.
Installation
1. Retirez le bloc d’alimentation de son emballage.
2. (Facultatif) À l’aide de l’outil de test de bloc d’alimentation fourni, connectez le
câble 24 broches au bloc d’alimentation, puis raccordez l’outil de test au câble 24
broches. Connectez le câble d’alimentation ATX au bloc d’alimentation et branchez
le câble PWR dans la sortie ou le parasurtenseur/système d’alimentation sans
coupure que vous envisagez d’utiliser. Une fois la connexion effectuée, placez
l’interrupteur sur la position Marche.
Remarque: si vous utilisez une configuration à refroidissement à l’eau, cet
outil de test est une option simple et sûre pour la purge/la vidange/le test
des composants à refroidissement à l’eau sans l’aide d’un trombone ou autre
dispositif.
Français
24
Manuel d’utilisation. Alimentation
750W / 850W / 1000W / 1200W TITANIUM
3. Utilisez les vis fournies avec le boîtier pour installer le bloc d’alimentation
dans votre ordinateur. REMARQUE: nous vous recommandons d’installer le
bloc d’alimentation avec le ventilateur orienté vers le bas. Cependant, si le
bloc d’alimentation est installé dans la partie inférieure du boîtier et qu’il n’y
a pas de trous d’aération, le mieux est de placer le bloc d’alimentation avec
le ventilateur orienté vers le haut pour plus d’effi cacité et de fi abilité.
4. Connectez le câble ATX 24 broches au bloc d’alimentation et à la carte
mère.
5. Connectez le câble EPS12V 4+4 broches au bloc d’alimentation et à la
carte mère. (Facultatif) – si vous planifi ez un overclocking extrême et que
votre carte mère dispose de connecteurs d’unité centrale 8 broches ou 4
broches supplémentaires, connectez le deuxième câble EPS12V 4+4
broches. Cela est uniquement nécessaire en cas d’overclocking extrême ou
pour les cartes mère d’unité centrale double.
6. Connectez les câbles PCI-E 6/6+2 broches à votre ou vos cartes
graphiques. REMARQUE: ne tentez pas de relier un câble PCI-E 8 broches
à un connecteur 6 broches sans avoir détaché les deux broches
supplémentaires au préalable.
7. Connectez les câbles d’alimentation SATA à tous les lecteurs de données ou
Obrigado por adquirir a Fonte EVGA 750T2/850T2/1000T2/1200T2 80PLUS® classificação Ouro! A 750T2/850T2/
1000T2/1200T2 é projetada com o entusiasta em mente, para fornecer energia limpa e contínua para todos os
componentes. O design totalmente modular fornece configurações de cabo personalizados para qualquer
aplicação e devido proximidade do ventilador silencioso da série 750T2/850T2/1000T2/1200T2 reduz o calor
durante a carga pesada, mantendo o baixo os níveis de decibéis. Além disso, o novo interruptor de controle ECO
térmico permite que o ventilador pare de girar para um funcionamento silencioso durante a baixa, média utilização
ou quando não for exigido esforço. O 750T2/850T2/1000T2/1200T2 inclui uma garantia excepcional de 10 anos e
tem uma classificação de MTBF de 100.000 horas de uso para lhe proporcionar tranquilidade sabendo que o seu
investimento estará coberto para os próximos anos.
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Informações de Segurança
AVISO1: Este produto não possui peças reparáveis pelo usuário. Abrir a carcaça representa um risco de choque e anula a garantia. A EVGA não
se responsabiliza por qualquer consequência gerada por uma utilização inadequada, incluindo mas não limitado a, uso para qual o produto não
se destina, ou uso incompatível com os termos da garantia disponibilizada online. (Informeções de garantia disponível em http://br.evga.com/
support/warranty e manual disponível em http://br.evga.com/support/manuals).
NEM TODOS OS CABOS MODULARES SÃO IGUAIS E COMPATÍVEIS! O uso de um cabo não oficialmente suportado poderá invalidar
AVISO2:
a sua garantia, causar uma falha de alimentação e/ou causar danos aos dispositivos conectados. Por favor, use APENAS os cabos oficiais
incluídos com a fonte de alimentação ou um conjunto alternativo de cabos oficiais listados para o seu modelo específico de fonte de alimentação
feito PELA EVGA. A EVGA NÃO SERÁ responsável por danos causados à sua fonte de alimentação, dispositivos ou cabos modulares não
oficiaias em eventos causados por uso de cabos modulares não suportados.
Conteúdo da Embalagem
Incluído com a sua fonte de alimentação 750T2/850T2/1000T2/1200T2 oferece os seguintes itens para a instalação
adequada e teste opcional:
750T2/850T2 Series1000T2/1200T2 Series
(1) Fonte EVGA
(1) Manual EVGA
(4) Parafusos de montagem
(1) Testador de Fonte EVGA (24-Pin)
(1) Bolsa de Cabo EVGA
(1) Cabo 24-Pin ATX
(2) Cabos 8(4+4)-Pin EPS/ATX12V
CPU
Português
(2) Cabos 8(6+2)-Pin PCI-E VGA
(2) Cabos 6-Pin + 8(6+2)-Pin
PCI-E VGA
(2) Cabos 3 SATA
(1) Cabo 4 SATA
(1) Cabo 4 Molex
(1) Adaptador Molex para FDD
(1) Cabo de alimentação
(opcional)
(1) Fonte EVGA
(1) Manual EVGA
(4) Parafusos de montagem
(1) Testador de Fonte EVGA
(24-Pin)
(1) Bolsa de Cabo EVGA
(1) Cabo 24-Pin ATX
(2) Cabos 8(4+4)-Pin EPS/
ATX12V CPU
30
(4) Cabos 8(6+2)-Pin PCI-E VG
(2) Cabos 6-Pin + 8(6+2)-Pin
PCI-E VGA
(3) Cabos 4 SATA
(2) Cabos 3 Molex
(1) Adaptador Molex para FDD
(1) Cabo de alimentação
(opcional)
A
Manual do Usuário para Fonte de Alimentação
750W / 850W / 1000W / 1200W TITANIUM
Recursos
ENERGIA ESTÁVEL
A série TITAINUM tem excelente desempenho energético com tensão estávele ultra potência extremamente
limpa. Isso pode ajudá-lo a atingir o mais alto possível overclock (opcional) e fornecer a energia mais estável
e confi ável para todos os componentes. A série Ouro também tem alta efi ciência de até 94% (115VAC) / 96%
(220VAC~240VAC) e é 80 PLUS TITAINUM.
Sistema de Controle Térmico ECO
O Sistema de Controle Térmico Inteligente ECO EVGA proporciona um funcionamento silencioso em baixas
cargas, maior efi ciência e maior vida útil do ventilador. Ativado por um interruptor simples diretamente na fonte
de alimentação, o recurso “rotação de fan nulo” é ideal para usuários que procuram reduzir o ruído geral em
ambientes. Economize nos custos de energia e uso fã desnecessário da fan com o Sistema de Controle Térmico
ECO EVGA.
A MELHOR PROTEÇÃO
A série TITAINUM é equipada com os maior conjunto de proteção possível, incluindo Proteção contra Sobretensão
(Over Voltage Protection, OVP), Proteção contra baixa tensão (Under Voltage Protection, UVP), Proteção contra ali-
mentação excessiva (Over Power Protection, OPP), Proteção contra Curto-Circuito (Short Circuit Protection, SCP),
Proteção de Sobrecorrente (Over Current Protection, OCP), Proteção contra Alta Temperatura (Over Temperature
Protection, OTP). Este produto também é coberto pela incrível garantia de 10 anos e o lendário Suporte EVGA.
QUALIDADE DE ACAMENTO SUPERIOR
A série T2 é construída com o mais alto padrão, utilizando capacitores 100% japoneses rotulados à 105 graus
Celsius e semicondutores de marcas de altíssima qualidade para uma melhor performance e durabilidade. A
ventoinha ultra silenciosa de 140mm com fans de rolamento duplo proporcionam refrigeração adequada
praticamente sem ruídos quando não for necessária e refrigeração ideal para operações pesadas.
DESIGN MODULAR
Diminuir a bagunça dentro do Gabinete, melhorar a temperatura ambiente com melhor fl uxo de ar e em geral
proporcionar uma aparência organizada para qualquer sistema. Design totalmente modular permite que o usuário
desligue o cabo do lado da fonte de alimentação, caso não seja necessário para a confi guração específi ca. Isso
pode ajudar a liberar espaço no interior da Gabinete e melhorar a organização dos cabos, bem como o fl uxo de ar
em todo o sistema.
Instalação
1. Retire a fonte de alimentação da embalagem.
2. (Opcional) Usando a ferramenta de teste de Fonte fornecido, conecte o cabo de 24
-Pin na fonte de alimentação, em seguida, anexar a ferramenta de teste para o cabo de
24-Pin. Conecte o cabo de alimentação ATX para a fonte de alimentação e ligue o
cabo PWR na tomada ou estabilizador / no-break que você planeja usar. Uma vez
conectado, ligue o interruptor de alimentação para a posição ON.
Atenção: Se você estiver usando uma configuração de refrigeração a água, esta
ferramenta de teste de forma simples e seguro, opção para o vazamento/
drenagem/componentes de resfriamento à água e teste sem a necessidade de um
clipe de papel ou outro dispositivo.
31
Português
Manual do Usuário para Fonte de Alimentação
750W / 850W / 1000W / 1200W TITANIUM
3. Use os parafusos fornecidos com o seu gabinete para instalar a fonte em
seu computador. NOTA: Recomenda-se instalar a fonte de alimentação
com a ventoinha voltada para baixo. No entanto, se o seu Gabinete o
encaixe da fonte de alimentação é na parte de baixo e não existem orifícios
de ventilação disponíveis, pode ser melhor instalar a fonte com a ventoinha
voltada para cima para uma maior efi ciência e confi abilidade.
4. Conecte o cabo ATX de 24-Pin de sua Fonte em sua placa-mãe.
5. Conecte o cabo 4+4-Pin EPS12V de sua Fonte em sua placa-mãe.
(Opcional) - Se você está pensando em realizar overclock e a sua
placa-mãe suporta 8-Pin adicional ou conectores de alimentação
da CPU de 4-Pin, conecte o segundo cabo EPS12V 4+4-Pin.
Isso só é necessário para overclocking pesado ou para placas-mãe
dual processadas. (Dual CPU)
6. Conecte os cabos PCIe de 6/6+2-Pin em sua(s) placa(s) de vídeo.
IMPORTANTE: Não tente conectar um cabo PCI-E de 8-Pin em um
conector de 6-Pin sem antes retirar os dois pinos adicionais.
7. Conecte os cabos de energia SATA aos seus dispositivos (discos rígidos,
SSDs e dríves ópticos).
8. Conecte os “Molex” conectores de 4-Pin periféricos para ventiladores,
bombas, componentes adicionais e outros dispositivos/adaptadores.
9. Conecte o cabo de alimentação para o fornecimento de energia na tomada.
Verifi que todas as conexões para garantir uma conexão sólida e ligue o
interruptor de alimentação da fonte de alimentação para a posição ON.
Português
32
Manual do Usuário para Fonte de Alimentação
750W / 850W / 1000W / 1200W TITANIUM
Perguntas Frequentes
P: Eu vejo há mais de 4 orifícios na parte traseira da fonte de alimentação, mas a embalagem só ofertas (4)
parafusos está faltando algum ?
R: Não falta nada, você só precisará anexar a fonte de alimentação EVGA no Gabinete com 4 parafusos. A fonte
de alimentação oferece mais de (4) orifícios para oferecer compatibilidade ideal para projetos atuais de Gabinetes
diferenciados.
P: Minha Fonte EVGA inclui 2 cabos EPS para a minha placa mãe, eu preciso conectar os dois juntos?
R: A maioria das placas-mães modernas requerem apenas conexão (1) 4+4 ou 8-Pin EPS. Em alguns modelos,
uma conexão de 4+4-Pin adicional sobre a placa-mãe pode ser encontrada para confi gurações CPU dual ou para
um overclocking. Se a sua placa-mãe suporta dupla 4+4-Pin EPS conexões, consulte o manual do fabricante da
placa para obter detalhes sobre o funcionamento adequado e utilização de energia das conexões EPS.
P: O que é Sistema de Controle Térmico Duplo.
R: O sistema de controle térmico ECO, quando ativado, permite que o ventilador em sua fonte de alimentação
EVGA pare de rodar durante a baixa e ou moderada carga de operação. O ventilador da fonte de alimentação
EVGA irá ligar-se automaticamente quando necessário, baseado na temperatura dos alcances de alimentação. O
ventilador também irá aumentar o RPM, quando necessário, com base na operação de carregamento ser
solicitada a partir dos componentes ligados. Isso evita a rotação desnecessária, reduz os níveis de ruído ambiente
e aumentar a vida útil do ventilador devido à ventoinha não girar quando não for necessário.
Atenção: Se o Controle Térmico ECO estiver desativado e o ventilador sempre irá girar, mesmo em baixas cargas.
O ventilador também irá aumentar em RPM automaticamente conforme necessário, com base no consumo de
energia de componentes ligados.
P: E se eu quiser usar adaptadores de energia para a minha placa(s) de vídeo/placa-mãe/periféricos ?
R: EVGA recomenda o uso de conexões de alimentação direta da fonte de alimentação para ligar a placa de
vídeo(s), as conexões de placas-mãe e de outras conexões de alimentação auxiliares para a distribuição de
energia ideal. Adaptadores de energia só deve ser necessário quando essa é a única opção.
P: Importa qual ponta do cabo vou plugar na fonte de alimentação?
R: Sim, as pontas que vão à fonte não terão interrupções, como o EPS (CPU) possui 4+4-Pin em uma ponta e
8 na outra. Outro exemplo é cabo de 24-Pin, você pode ver na fonte que há um total de 28-Pin, já a conexão
da placa-mãe recebe 24-Pin. Verifi que cuidadosamente cada cabo de acordo com sua etiqueta para conectar o
lado correto à fonte e o mesmo cabo ao componente correspondente.
P: Se eu tiver um problema ou uma dúvida, posso obter suporte?
R: Todos os produtos EVGA contam com garantia, assim como suporte técnico. O Suporte de sua fonte pode ser
obtido através do Skype “SuporteEVGA”, ou entre em contato por e-mail através do support@evga.com.
33
Português
Manual do Usuário para Fonte de Alimentação
750W / 850W / 1000W / 1200W TITANIUM
SuperNOVA 750/850T2 Configuração de cabos
Conexão ModularCablesCor do Cabo
MB1 x ATX 24-Pin
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
SATA1
SATA2
SATA3
PERIF11 x Molex 4-Pin x 4
FDD1 x Molex to FDD Adapter
SuperNOVA 750/850T2 Especificação
2 x EPS/ATX12V 8(4+4)-Pin
2 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
2 x SATA 5-Pin x 3
1 x SATA 5-Pin x 4
Preto
SuperNOVA 750W TITANIUM
Entrada AC
Saída DC+5V+3.3V+12V-12V+5Vsb
Saída Máxima, A
Combinado, W
Potencia de
salida, Pcont
20A20A62.4A0.5A2.5A
100W748.8W
100-240 VAC, 10A, 60/50 Hz
SuperNOVA 850W TITANIUM
Entrada AC
Saída DC+5V+3.3V+12V-12V+5Vsb
Saída Máxima, A
Combinado, W
Potencia de
salida, Pcont
20A20A70.8A0.5A2.5A
100W849.6W
100-240 VAC, 10A, 60/50 Hz
+50°C ambiente à pleno funcionamento
6W12.5W
750W @ +50°C
+50°C ambiente à pleno funcionamento
6W12.5W
850W @ +50°C
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Proteção contra Sobretensão, Proteção contra Subtensão, Proteção contra Curto-Circuito,
Proteção contra Sobrecarga, Proteção de Sobrecorrente, Proteção contra Alta Temperatura.
SATA3
PERIF/SATA2 x Molex 4-Pin x 3
FDD1 x Molex to FDD Adapter
SuperNOVA 1000/1200T2 Especificação
2 x EPS/ATX12V 8(4+4)-Pin
4 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
3 x SATA 5-Pin x 4SATA2
Preto
SuperNOVA 1000W TITANIUM
Entrada AC
Saída DC+5V+3.3V+12V-12V+5Vsb
Saída Máxima, A
Combinado, W
Potência de
Saída, Pcont
20A20A83.3A0.5A2.5A
100W999.6W
100-240 VAC, 15A, 60/50 Hz
SuperNOVA 1200W TITANIUM
Entrada AC
Saída DC+5V+3.3V+12V-12V+5Vsb
Saída Máxima, A
Combinado, W
Potência de
Saída, Pcont
20A20A99.9A0.5A2.5A
100W1198.8W
100-240 VAC, 15A, 60/50 Hz
+50°C ambiente à pleno funcionamento
6W12.5W
1000W @ +50°C
+50°C ambiente à pleno funcionamento
6W12.5W
1200W @ +50°C
Dimensions: 85mm (H) x 150mm (W) x 180mm (L)
Proteção contra Sobretensão, Proteção contra Subtensão, Proteção contra Curto-Circuito,
Proteção contra Sobrecarga, Proteção de Sobrecorrente, Proteção contra Alta Temperatura.
Grazie per aver acquistato l’unità di alimentazione EVGA 750T2/850T2/1000T2/1200T2 80 PLUS® TITANIUM!
L’unità 750T2/850T2/1000T2/1200T2, progettata per gli appassionati, eroga energia pulita e continua a ogni
componente. Il design completamente modulare consente configurazioni dei cavi su misura per qualsiasi
applicazione e, grazie alla ventola quasi silenziosa, la serie 750T2/850T2/1000T2/1200T2 riduce l’emissione di calore
durante l’uso intensivo e la rumorosità. Inoltre, il nuovo interruttore per il controllo termico ECO consente di arrestare
la rotazione della ventola per un funzionamento silenzioso quando non è necessaria a carico medio-basso. La
750T2/850T2/1000T2/1200T2 include un’eccezionale garanzia di 10 anni e ha un rating MTBF di 100.000 ore e
quindi potrai essere certo che il tuo investimento sarà protetto negli anni a venire.
SuperNOVA 750W TITANIUM
SuperNOVA 1000W TITANIUM
SuperNOVA 850W TITANIUM
SuperNOVA 1200W TITANIUM
Informazioni di sicurezza
ATTENZIONE1: questa unità non ha parti manutenibili dall’utente al suo interno. L’apertura del case comporta un rischio di folgorazione e invaliderà
la garanzia del prodotto. EVGA non sarà responsabile per qualsiasi uso improprio, incluso, ma non limitato a, qualsiasi utilizzo del prodotto non
conforme alla sua destinazione o un utilizzo non conforme con le condizioni di garanzia disponibili online. (Le informazioni sulla garanzia sono
disponibile su
NON TUTTI I CAVI MODULARI SONO UGUALI O COMPATIBILI! L’utilizzo di un cavo non ufficialmente supportato può invalidare
ATTENZIONE2:
la garanzia, causare un guasto all’alimentatore e/o causare danni ai dispositivi collegati. Si prega di utilizzare SOLO i cavi ufficialmente supportati
inclusi con l’alimentatore, o i cavi alternativi ufficialmente supportati indicati per il modello specifico dell’alimentatore, PRODOTTI DA EVGA.
EVGA NON sarà responsabile per danni causati all’alimentatore, dispositivi o cavi modulari non ufficialmente supportati se il danno è causato
dall’utilizzo di cavi modulari non ufficialmente supportati.
www.evga.com/support/warranty e questo manuale è disponibile su www.evga.com/manuals
).
Contenuto della confezione
Nella confezione dell’alimentatore EVGA 750T2/850T2/1000T2/1200T2 sono inclusi i seguenti componenti per
La serie SuperNOVA TITANIUM offre eccezionali prestazioni elettriche con una tensione ultra stabile e una
erogazione della potenza elettrica estremamente pulita. Questo consente di ottenere il più alto overclocking
possibile (opzionale) ed erogare una potenza estremamente stabile e affidabile a tutti i componenti. La serie
SuperNOVA TITANIUM offre inoltre un’elevata efficienza - fino al 94% (115 V CA)/96% (220 V CA~240 V CA)
- ed è certificata 80 PLUS TITANIUM.
SISTEMA DI CONTROLLO TERMICO ECO
L’intelligente sistema di controllo termico ECO di EVGA offre un funzionamento silenzioso ai bassi carichi,
un’efficienza migliorata e una vita in servizio della ventola più lunga. Abilitata con un semplice interruttore
sull’alimentatore, la funzione “No Fan Spin” è ideale per gli utenti che desiderano ridurre la rumorosità ambientale
complessiva. Risparmia sui costi energetici ed evita di utilizzare la ventola inutilmente con il sistema di controllo
termico ECO di EVGA.
PROTEZIONE DI ALTISSIMA QUALITÀ
La serie TITANIUM è dotata del sistema di protezione più completo, fra cui protezione dalla sovratensione (OVP),
protezione dalla sottotensione (UVP), protezione dalla sovralimentazione (OPP), protezione dai cortocircuiti (SCP),
protezione dalla sovracorrente (OCP) e protezione dalla sovratemperatura (OTP). Questo prodotto è anche coperto
dall’eccezionale garanzia di 10 anni e il leggendario servizio clienti e supporto di EVGA.
QUALITÀ DI COSTRUZIONE SUPERIORE
La serie SuperNOVA TITANIUM è stata costruita secondo i più alti standard, utilizzando condensatori 100%
giapponesi (temperatura di esercizio 105 gradi Celsius) e semiconduttori di marchio di alta qualità per il massimo
delle prestazioni e affidabilità. La ventola Ultra Quiet con cuscinetto a doppia sfera di 140 mm offre un adeguato
raffreddamento per un funzionamento quasi silenzioso quando non è necessaria e il corretto raffreddamento
durante il funzionamento a pieno carico.
DESIGN MODULARE
Riduci il numero di componenti nel case e migliora la temperatura ambientale con un flusso d’aria ottimizzato, il
tutto con un look estremamente pulito. I design completamente modulari delle PSU consentono all’utente di
scollegare i cavi dal lato dell’alimentatore se non sono necessari per la configurazione specifica. Questo può aiutare
a liberare spazio all’interno del case e a migliorare la gestione dei cavi, così come il flusso d’aria in tutto il sistema.
Installazione
1. Rimuovere l’alimentatore dalla confezione.
(Opzionale) Utilizzando il tester della PSU, collegare il cavo a 24 pin alla PSU e quindi
2.
collegare il tester al cavo a 24 pin. Collegare il cavo di alimentazione ATX alla PSU
e inserire il cavo PWR nella presa o protezione dalla sovratensione/UPS che si
prevede di usare. Una volta collegato, accendere l’unità premendo l’interruttore di
alimentazione (posizione “ON”). (Se la modalità ECO è impostata su ON, la ventola
non sarà in funzione)
Nota: se si utilizza un sistema di raffreddamento ad acqua, questo tester è
un’opzione semplice e sicura per lo spurgo/drenaggio/test dei componenti di
raffreddamento ad acqua, senza dover utilizzare una graffetta o altro dispositivo.
Italiano
38
750W / 850W / 1000W / 1200W TITANIUM
Utilizzare le viti fornite con il case per installare l’alimentatore nel
3.
proprio computer. NOTA: si raccomanda di installare
l’alimentatore con la ventola rivolta verso il basso. Tuttavia, se
nel case l’alimentatore è ubicato sulla parte inferiore e fori di
ventilazione non sono disponibili, è possibile installare
l’alimentatore con la ventola rivolta verso l’alto per una
maggiore efficienza e affidabilità.
Collegare il cavo ATX da 24 pin alla scheda madre.
4.
5.
Collegare il cavo EPS12V da 4+4 pin alla scheda madre.
(Opzionale) – se si intende utilizzare un overclocking estremo
e la propria scheda madre supporta connettori per l’alimentazione della CPU a 8 pin o 4 pin, collegare il secondo cavo
EPS12V da 4+4 pin. Questo è solo necessario per un
overclocking estremo o per schede madri con doppia CPU.
Collegare i cavi PCI-E 6/6+2 pin alla scheda grafica o schede
6.
grafiche. NOTA: non tentare di collegare un cavo PCI-E a 8 pin
a un connettore a 6 pin senza prima rimuovere i due pin
supplementari.
Collegare i cavi di alimentazione SATA a tutte le unità di dati o
7.
unità ottiche (hard disk, unità stato solido, unità ottiche).
Manuale utente Unità alimentazione
Collegare i connettori “Molex” periferici a 4 pin a ventole,
8.
pompe,componenti legacy e altri dispositivi/adattatori.
Collegare il cavo di alimentazione CA all’alimentatore e alla
9.
presa a muro. Controllare tutti i collegamenti per assicurarsi che
siano ben saldi e accendere l’alimentatore premendo
l’interruttore di alimentazione (posizione “ON”).
39
Italiano
Manuale utente Unità alimentazione
750W / 850W / 1000W / 1200W TITANIUM
Domande e risposte
D. Sul retro dell’alimentatore sono presenti più di quattro fori per le viti, ma nella confezione ci sono solo (4) viti;
mancano alcune viti?
R. Non manca nulla; l’alimentatore EVGA viene montato nel case con le quattro viti in dotazione. L’alimentatore è
dotato di più di (4) fori per offrire una compatibilità ottimale con tutti i design dei case moderni.
D. La mia unità di alimentazione EVGA include (2) cavi EPS per la scheda madre; è necessario collegarli
R. Le schede madri necessitano di (1) solo collegamento EPS a 4+4 o 8 pin. Su alcuni modelli, la scheda
madre è dotata di un collegamento a 4+4 o 8 pin aggiuntivo per configurazioni a doppia CPU o per un
overclocking estremo. Se la scheda madre supporta due collegamenti EPS a 4+4 pin, consultare il manuale del
produttore della scheda madre per dettagli sul funzionamento e l’alimentazione dei collegamenti EPS.
D. Cos’è il sistema di controllo termico ECO?
R. Il sistema di controllo termico ECO, se abilitato, consente alla ventola dell’alimentatore EVGA di spegnersi con
un funzionamento a carichi da bassi a moderati. La ventola dell’alimentatore EVGA si riaccenderà automatica-
mente solo quando è necessario, in base alla temperatura raggiunta dall’alimentatore. La ventola aumenterà
anche la velocità di funzionamento (giri/min.) in base al carico richiesto dai componenti collegati, se necessario.
Questo previene inutili rotazioni, riduce i livelli di rumorosità ambientale e aumenterà la vita in servizio della
ventola a causa della ridotta rotazione.
Nota: se il controllo termico ECO è disattivato, la ventola sarà sempre in funzione, anche ai carichi bassi. La
ventola aumenterà automaticamente anche la velocità di funzionamento (giri/min.), in base all’assorbimento
elettrico dei componenti collegati, se necessario.
D. E se volessi utilizzare adattatori di corrente per la mia scheda grafica/scheda madre/periferiche?
R. EVGA raccomanda sempre l’utilizzo di collegamenti diretti alla rete elettrica per alimentare tutti i componenti.
D. È importante quale estremità del cavo si inserisce nell’unità di alimentazione?
R. Sì, i collegamenti all’alimentatore non possono essere “separati” come il connettore EPS (CPU), il quale è
formato da 4+4 pin su un lato e da 8 pin (intero) sull’altro. Controllare ciascun cavo in quanto tutti i cavi sono
etichettati per il collegamento corretto all’alimentatore e collegare direttamente all’alimentatore solo il cavo
‘‘corrispondente”, come riportato su ciascun connettore.
D. Se ho un problema o una domanda, è possibile richiedere assistenza?
R. TUTTI i prodotti EVGA sono supportati da garanzie top tier e da supporto tecnico. Se si necessita di supporto
per il proprio alimentatore, vedere i dettagli di contatto di seguito:
USA: +1-888-881-3842 opzione 1, opzione 3 o inviare un’e-mail a support@evga.com.
Europa: +49 89 189 049 11 o inviare un’e-mail tramite eu.evga.com/support.
Italiano
40
Manuale utente Unità alimentazione
750W / 850W / 1000W / 1200W TITANIUM
Configurazione dei cavi SuperNOVA 750/850T2
Connettore modulareCaviColore cavo
MB1 x ATX 24-Pin
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
SATA1
SATA2
SATA3
PERIF11 x Molex 4-Pin x 4
FDD1 x Molex to FDD Adapter
Configurazione dei cavi SuperNOVA 750/850T2
2 x EPS/ATX12V 8(4+4)-Pin
2 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
2 x SATA 5-Pin x 3
1 x SATA 5-Pin x 4
Nero
+50°C ambiente a pieno carico
6W12.5W
+50°C ambiente a pieno carico
6W12.5W
Ingresso CA
Uscita CC
Uscita MAX, A
Combinata, W
Potenza di uscita,
Pcont
Ingresso CA
Uscita CC
Uscita MAX, A
Combinata, W
Potenza di uscita,
Pcont
SuperNOVA 750W TITANIUM
100-240 VAC, 10A, 60/50 Hz
+5V+3.3V+12V-12V+5Vsb
20A20A62.4A0.5A2.5A
100W748.8W
750W @ +50°C
SuperNOVA 850W TITANIUM
100-240 VAC, 10A, 60/50 Hz
+5V+3.3V+12V-12V+5Vsb
20A20A70.8A0.5A2.5A
100W849.6W
850W @ +50°C
Dimensioni: 85 mm (A) x 150 mm (L) x 180 mm (P)
protezione dalla sovratensione, protezione dalla sottotensione, protezione dai cortocircuiti,
protezione dalla sovralimentazione, protezione dalla sovracorrente, protezione dalla sovratemperatura.
SATA3
PERIF/SATA2 x Molex 4-Pin x 3
FDD1 x Molex to FDD Adapter
Configurazione dei cavi SuperNOVA 1000/1200T2
2 x EPS/ATX12V 8(4+4)-Pin
4 x PCI-E 8(6+2)-Pin
2 x PCI-E 6-Pin + 8(6+2)-Pin
3 x SATA 5-Pin x 4SATA2
Nero
+50°C ambiente a pieno carico
6W12.5W
+50°C ambiente a pieno carico
6W12.5W
Ingresso CA
Uscita CC
Uscita MAX, A
Combinata, W
Potenza di uscita,
Pcont
Ingresso CA
Uscita CC
Uscita MAX, A
Combinata, W
Potenza di uscita,
Pcont
SuperNOVA 1000W TITANIUM
100-240 VAC, 15A, 60/50 Hz
+5V+3.3V+12V-12V+5Vsb
20A20A83.3A0.5A2.5A
,
100W999.6W
1000W @ +50°C
SuperNOVA 1200W TITANIUM
100-240 VAC, 15A, 60/50 Hz
+5V+3.3V+12V-12V+5Vsb
20A20A99.9A0.5A2.5A
100W1198.8W
1200W @ +50°C
Dimensioni: 85 mm (A) x 150 mm (L) x 180 mm (P)
protezione dalla sovratensione, protezione dalla sottotensione, protezione dai cortocircuiti,
protezione dalla sovralimentazione, protezione dalla sovracorrente, protezione dalla sovratemperatura.
Italiano
42
MEMO
43
MEMO
44
E006-00-000075
V2_201611
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.