EVGA 630i, e-7050, 112-CK-NF70, 7150, e-610i User Manual

Before You Begin…

Parts NOT in the Kit

This kit contains all the hardware necessary to install and connect your new EVGA
e-7050/610i GPU motherboard with integrated GeForce graphics processing. However, it
does not contain the following items that must be purchased separately to make the
motherboard fully functional.

 Intel microprocessor:

 Cooling fan and heat sink for the microprocessor

 System memory support

 Hard Disk Drive(s)

 Operating System

 Power Supply

 Graphics Card

EVGA assumes you have purchased all necessary parts needed to allow for proper system
functionality.

Motherboard Specifications

 Size

mATX form factor.

 Microprocessor support

Intel Core 2 Extreme, Intel Core 2 Quad, Intel Core 2 Duo, Pentium EE, Pentium, and
Celeron. (The e-7050/610i supports up to 1066MHz FSB CPU’s)

 Operating systems

Supports Windows XP and Windows Vista.

 Contains an NVIDIA nForce MCP and integrated GeForce graphics

 System Memory

• Single-channel DDR2 667/533

• Supports up to 4 GB DDR2 memory (2GB x 2)

 USB 2.0 Ports

• Supports hot plug

• Up to eight (4 onboard) USB 2.0 ports

• Supports USB 2.0 protocol up to 480Mbps transmission rate

 Onboard Serial ATA II

• 3Gb/s data transfer rate

• Four Serial ATA II connectors

• Support for RAID 0, RAID 1

• Supports hot plug and NCQ (Native Command Queuing )

 Onboard LAN

• LAN interfaces built-in onboard

• 10/100 LAN

 Onboard Audio

• Supports 6-channel audio

• Supports Jack-Sensing function

 PCI Express x16 Support

• Supports 4 GB/sec (8 GB/sec concurrent) bandwidth

 Onboard Video

• Integrated video

• A VGA output is provided

 Expansion Slots

• Two PCI slots

• One PCI Express x1 slot

• One PCI Express x16 Graphics slot

Hardware Installation

This section will guide you through the installation of the motherboard. The topics covered in this
section are:

• Preparing the motherboard

• Installing the CPU

• Installing the CPU fan

• Installing the memory

• Installing the motherboard

• Connecting cables and setting switches

Safety Instructions

To reduce the risk of fire, electric shock, and injury, always follows basic safety
precautions.

Remember to remove power from your computer by disconnecting the AC main
source before removing or installing any equipment from/to the computer chassis.

EVGA nForce Motherboard

The EVGA nForce motherboard with the 600 series MCP processor is a PCI Express
motherboard with an onboard GeForce graphics card. Figure 1 shows the 7150/630i
motherboard and Figures 2 shows the back panel connectors.

m

r

t

e

e

m

S

E

E

k

n

n

h

t

y

d

E

E

e

n

t

L

15

12

12

13

14

16

11

17

10

18

1

19

10

2

3

4

1.

2.

3.

4.

5.

6.

7.

8.

9.

9

CPU Socket

NVIDIA MCP with

4-Pin CPU Fan Co

DDR2 DIMM Me

FDD Connector

24-Pin ATX Powe

IDE HDD Connec

SATA Ports

Front Panel Head

8

Passive Cooling

nnector

ory Slots

Connector

or

Figur

1. e-7010

7

10. USB

11. Fron

12. PCI

13. PCI-

14. PCI-

15. Bac

16. 4-Pi

17. 3-Pi

18. Mot

Note: Actual

6

2.0 Header

t Panel Audio Hea

lots

x1 Slot

x16 Slot

Panel Connectors

CPU Power Conn

System Fan Con

erboard CMOS Ba

/610i Mo

otherboard may var

5

19.

Clear CMOS Jumpe

er

ctor

ector

tery

herboard

from pictures

ayout