Page 1
Page 2
Parts NOT in the Kit
This kit contains all the hardware necessary to install and connect your new EVGA nForce
motherboard. However, it does not contain the following items that must be purchased
separately to make the motherboard functional.
Intel microprocessor:
Intel Core 2 Extreme, Intel Core 2 Quad, Intel Core 2 Duo, Pentium EE, Pentium, and
Celeron Socket 775 CPU’s. (up to 1066Mhz FSB on 610i motherboards)
Cooling fan and heat sink for the microprocessor
System memory support:
Supports single channel DDR2 533/667/800, (800MHz not supported on 610i
Motherboards )
Power Supply
The power supply requirement is dependent upon the components used in the system.
We recommend at least a 350 watt power supply for a basic configuration.
*Graphics Card*
This motherboard comes with an onboard graphics adapter; it also has a PCI express x16
slot for graphics cards.
Before You Begin…
These instructions help you install each of the parts listed so you can have a functioning
motherboard. As you go through the installation instructions, we are assuming you have
purchased the necessary parts.
Motherboard Specifications
Size
mATX form factor.
Microprocessor support
Intel Core 2 Extreme, Intel Core 2 Quad, Intel Core 2 Duo, Pentium EE, Pentium, and
Celeron. (610i supports up to 1066MHz FSB CPU’s)
Operating systems
Supports Windows XP and Windows Vista.
Contains NVIDIA nForce MCP and integrated GeForce graphics
System Memory
• Single-channel DDR2 800/667/533 (800MHz RAM not supported on 610i)
• Supports up to 4 GB DDR2 memory (2GB x 2)
USB 2.0 Ports
Page 3
• Supports hot plug
• Up to ten USB 2.0 ports
• Supports USB 2.0 protocol up to 480Mbps transmission rate
Onboard Serial ATA II
• 3Gb/s data transfer rate
• Four Serial ATA II connectors
• Support for RAID 0, RAID 1, RAID 0+1, and RAID 5, (RAID 0+1 and RAID 5
not supported on 610i)
• Supports hot plug and NCQ (Native Command Queuing )
Onboard LAN
• LAN interfaces built-in onboard
• Gigabit Ethernet (10/100 LAN on 610i motherboards)
Onboard 1394
• 1394 port and header available on 630i Motherboards
Onboard Audio
• Supports 8-channel audio (6-channel on 112-CK-NF71-T1)
• Supports S/PDIF output (on 630i motherboards)
• Supports Jack-Sensing function
PCI Express x16 Support
• Supports 4 GB/sec (8 GB/sec concurrent) bandwidth
Onboard Video
• Integrated video
• All models support VGA out. On models with DVI, out a single link digital display is
supported. Certain models come equipped with an HDMI connecter to connect an
HDTV. Dual display is supported with VGA and DVI or VGA and HDMI.
Expansion Slots
• Two PCI slots
• One PCI Express x1 slot
• One PCI Express x16 Graphics slot
Page 4
Hardware Installation
This section will guide you through the installation of the motherboard. The topics covered in this
section are:
Preparing the motherboard
• Installing the CPU
• Installing the CPU fan
• Installing the memory
Installing the motherboard
Connecting cables and setting switches
Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follows basic safety
precautions.
Remember to remove power from your computer by disconnecting the AC main
source before removing or installing any equipment from/to the computer chassis.
Page 5
EVGA nForce Motherboard
The EVGA nForce motherboard with the 600 series MCP processor is a PCI Express
motherboard with an onboard GeForce graphics card. Figure 1 shows the 7150/630i
motherboard and Figures 2 shows the back panel connectors.
Page 6
Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU or memory. You need to
purchase a CPU, a CPU heat sink/fan assembly, and memory module(s) to complete this
installation.
Page 7
Installing the CPU
Be very careful when handling the CPU. Hold the processor only by the edges and do not
touch the bottom of the processor.
Use the following procedure to install the CPU onto the
motherboard.
1. Unhook the socket lever by pushing down and away from the
socket.
2. Lift the load plate. There is a protective socket cover on the
load plate to protect the socket when there is no CPU
installed.
3. Remove the protective socket cover from the load plate.
4. Remove the processor from its protective cover, making sure
you hold it only by the edges.
It is a good idea to save the cover so that whenever you
remove the CPU, you have a safe place to store it.
5. Align the notches in the processor with the notches on the
socket.
6. Lower the processor straight down into the socket with out
tilting or sliding it into the socket
Note: Make sure the CPU is fully seated and level i n the socket.
Align notches with
7. Close the load plate over the CPU and press down while you
close and engage the socket lever.
notches on the CPU
Installing the CPU heat sink/fan
There are many different heat sink types that can be used with this motherboard. Follow the
instruction that came with your fan assembly. Be sure that the fan orientation is correct for
your chassis type and your fan assembly.
Installing Memory DIMMs
Your new motherboard has two 1.8V 240-pin slots for DDR2 memory. These slots support
256 MB, 512 MB, 1 GB, and 2 GB DDR2 technologies. There must be at least one memory
bank populated to ensure normal operation.
*Any of the two DIMM slots may be used as primary if only using one memory module.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into the
DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock the
DIMM into the connector.
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis you are
using and if you are replacing an existing motherboard or working with an empty chassis.
Page 8
Determine if it would be easier to make all the connections prior to this step or to secure the
motherboard and then make all the connections.
Use the following procedure to install the I/O shield and secure the motherboard into the
chassis.
Note: Be sure that the CPU fan assembly has enough clearance for the chassis covers to lock
into place and for the expansion cards. Also make sure the CPU Fan assembly is aligned
with the vents on the covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust, foreign objects, and promotes
correct airflow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis. Press
the I/O shield into place and make sure it fits securely. If the I/O shield does not fit into
the chassis, you would need to obtain the proper size from the chassis supplier.
Securing the Motherboard into the Chassis
Most computer chassis have a base with mounting studs or spacers to allow the
motherboard to be secured to the chassis and help to prevent short circuits. If there are
studs that do not align with a mounting hole on the motherboard, it is recommended that
you remove that stud to prevent the possibility of a short circuit.
1. Carefully place the motherboard onto the studs/spacers located inside the chassis.
2. Align the mounting holes with the studs/spacers.
3. Align the connectors to the I/O shield.
4. Ensure that the fan assembly is aligned with the chassis vents according to the fan
assembly instruction.
5. Secure the motherboard with a minimum of six screws.
Power Connections
This motherboard requires an ATX power supply. Make sure your power supply can
provide enough wattage to power all the components you will be installing.
24-pin ATX Power (PWR1)
PWR1 is the main power supply connector located along the edge of the board next to the
DIMM slots. Make sure that the power supply cable and pins are properly aligned with the
connector on the motherboard. Firmly plug the power supply cable into the connector and
make sure it is secure.
PWR1 connector
Plug power cable
from system power
supply to PWR1
Page 9
8-pin ATX 12V Power (PWR2)
PWR2, the 8-pin ATX 12V power connection, is used to provide power to the CPU. Align
the pins to the connector and press firmly until seated.
It is strongly recommended that you use an 8-pin ATX 12V power supply; however a four-pin
power supply may be used. The 8 pin power connection is keyed for either a 4 pin or 8 pin
connector to only go in one way.
Connecting IDE Hard Disk Drives
The IDE connector supports Ultra ATA 133/100/66 IDE hard disk drives.
Connect the cable end with a single connector to the motherboard.
If you install two hard disk drives, you must configure the second drive as a slave device by
setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings.
Connecting Serial ATA Cables
The Serial ATA II connector is used to connect the
Serial ATA II device to the motherboard. These
connectors support the thin Serial ATA II cables for
primary storage devices. The current Serial ATA II
interface allows up to 300MB/s data transfer rate.
There are four serial ATA connectors on the motherboard that
support RAID 0, RAID 1, RAID 5, and RAID 0+1
configurations. (610i motherboards support RAID0 or RAID1
only)
Connecting Internal Headers
Please refer to item 10 in figure 1 Motherboard.
Front Panel Header
The front panel header on this motherboard is one
connector used to connect the following four cables:
PWRLED
Attach the front panel power LED cable to the PWR LED connector. The Power LED
indicates the system’s status.
Page 10
PWRSW
Attach the power button cable from the case to these two pins. Pressing the powerbutton
on the front panel turns the system on off rather than using the power supply button.
HD_LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator
LED indicates the activity status of the hard disks.
RESET
Attach the Reset switch cable from the front panel of the case to these two pins. The
system restarts when the
RESET switch is pressed.
USB Headers
The motherboard contains 10-pin internal USB
header connector(s). These can be used for your
front panel USB connections or a USB bracket.
Audio
The audio connector supports the HD audio standard. Most cases come with a 10 pin
standard block which will align and plug directly in to the header. In some cases there will
be individual plugs which will need to be plugged in.
Table 1. Front Audio Connector
Connector Pin Signal
Front Audio Connector
1
3
5
7
9
Fan Connections
There are two types fan connections, the system fan and the CPU fan. The fan speed can be
detected and viewed in the
automatically turned off after the system enters S3, S4 and S5 mode.
Note that the CPU fan cable can be
either a 3-pin or a 4-pin connector.
Connect a 3-pin connector to pins 1, 2,
and 3 on the motherboard connector.
2
4
6
8
10
1 PORT1_L - Analog Port 1 - left channel (Microphone)
2 AUD_GND - Ground
3 PORT1_R – Analog Port 1 – right channel (Microphone)
4 PRESENCE# - Active signal that indicates FP audio is present
5 PORT2_R – Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN – Jack detection return for front panel (Jack1)
7 SENSE_SEND – Jack detection sense line
8 Empty
9 PORT2_L – Analog port 2 – left channel (Headphone)
10 SENSE2_RETURN – Jack detection return for front panel (Jack2)
PC Health Status section of the CMOS Setup. Both fans are
CPU Fan Connector
4 3 2 1
GND SENSE
PWR CONTROL
Page 11
FDD Connector
The motherboard supports a standard 360K, 720K, 1.2M, 1.44m, and a 2.88M floppy disk
drive (FDD).
Speaker
The speaker connector is used to connect the chassis speakers to the motherboard. Please
refer to item 9 in figure 1 Motherboard.
Expansion Slots
The EVGA nForce motherboard contains four expansion slots, two PCI Express slots and
two PCI slots. For a full list of PCI Express x16 graphics card supported by this
motherboard, go to www.evga.com/products/.
PCI Slots
The two PCI slots support many expansion cards such as a LAN card, USB card, SCSI card
and other cards that comply with PCI specifications. When installing a card into the PCI
slot, be sure that it is fully seated. Secure the card’s metal bracket to the chassis back panel
with the screw used to hold the blank cover.
PCI Express x1 Slot
There is one PCI Express x1 slot that is designed to accommodate less bandwidth-intensive
cards, such as a modem or LAN card. The x1 slot provides 250 MB/sec bandwidth.
PCI Express x16 Slot
The PCI Express x16 slot is reserved for a graphics card. The bandwidth of the x16 slot is
up to 4GB/sec (8GB/sec concurrent). When installing a PCI Express x16 card, be sure the
retention clip snaps and locks the card into place. If the card is not seated properly, it could
cause a short across the pins. Secure the card’s metal bracket to the chassis back panel with
the screw used to hold the blank cover.
Install your Operating System
Boot up your machine, setup any hardware configurations in the BIOS setup if needed.
Boot from your OS disk. Once your operating system is installed use the driver disk to
install the appropriate drivers.
Page 12
On-board LED Codes
On-board LED Codes
Code(hex) Name Description
01 Reserved
02 Jumps to E000
segment
03 Early Superio Init Early Initialized the super IO
04 Reserved
05 Blank video Reset Video controller
06 Reserved
07 Init KBC Keyboard controller init
08 KB test Test the Keyboard
09 Reserved
0A Mouse Init Initialized the mouse
0B Reserved
0C Reserved
0D Reserved
0E CheckSum Check Check the integrity of the ROM,BIOS and
0F Reserved
10 Autodetect EEPROM Check Flash type and copy flash
11 Reserved
12 Test CMOS Test and Reset CMOS
13 Reserved
14 Load Chipset Load Chipset Defaults
15 Reserved
16 Init Clock Initialize onboard clock generator
17 Reserved
18 InitCPU CPU ID and initialize L1 /L2 cache
19 Reserved
1A Reserved
1B Setup Interrupt Initialize first 120 interrupt vectors Vector Table with
1C CMOS Battery Check Test CMOS and check Battery Fail
1D Early PM Early PM
initialization
Execution of POST routines in E000
message
Write/erase routines
SPURIOUS_INT_HDLR and initialize INT 00h-1Fh
according to INT_TBL
Page 13
Code(hex) Name Description
1E Reserved
1F Re-initial KB Load keyboard matrix
20 Reserved
21 HPM init Init Heuristic Power Management (HPM)
22 Reserved
23 Program chipset Early Programming of chipset registers
24 Init PNP Init PNP
25 Shadow VBIOS Shadow system/video BIOS
26 Clock Gen Init onboard clock generator and sensor
27 Setup BDA Setup BIOS DATA AREA (BDA)
28 Reserved
29 CPU Speed detect Chipset programming and CPU Speed detect
2A Reserved
2B Init video Initialize Video
2C Reserved
2D Video memory test Test Video Memory and display Logos
2E Reserved
2F Reserved
30 Reserved
31 Reserved
32 Reserved
33 Early keyboard reset Early Keyboard Reset
34 Reserved
35 Test DMA Controller 0 Test DMA channel 0
36 Reserved
37 Test DMA Controller
1
38 Reserved
39 Test DMA Page
Registers
3A Reserved
3B Reserved
3C Test Timer Test 8254 Timer 0 Counter 2.
3D Reserved
3E Test 8259-1 Mask Verify 8259 Channel 1 masked interrupts by
3F Reserved
40 Test 8259-2 Mask Verify 8259 Channel 2 masked interrupts by
41 Reserved
42 Reserved
43 Test Stuck Interrupt Turn off interrupts then verify no 8259's Interrupt
44 Reserved
Test DMA channel 1
Test DMA Page Registers
alternately turning off and on the interrupt line s.
alternately turning off and on the interrupt line s.
mask register is on. Test 8259 Force an interrupt
and verify the interrupt occurred.
Page 14
Code(hex) Name Description
45 Reinit serial port Reinitialize Preboot agent serial port
46 Reserved
47 EISA Test If EISA non-volatile memory checksum is good,
48 Reserved
49 Size Memory Size base memory from 256K to 640K and extended
4A Reserved
4B Reserved
4C Reserved
4D Reserved
4E Init APIC Initialize APIC and set MTRR
4F Reserved
50 USB init Initialize USB contro ller
51 Reserved
52 Memory Test Test all memory of memory above 1MB using Virtual
53 Reserved
54 Reserved
55 CPU display Detect CPU speed and display CPU vendor specific
56 Reserved
57 PnP Init Display PnP logo and PnP early init
58 Reserved
59 Setup Virus Setup virus protect according to protect setup
5A Reserved
5B Awdflash Load If required, will auto load Awdflash. exe in POST
5C Reserved
5D Onboard I/O Init Initializing onboard superIO
5E Reserved
5F Reserved
60 Setup enable Display setup message and enable setup functi ons
61 Reserved
62 Reserved
63 Initialize Mouse Detect if mouse is present, initialize mouse, install
64 Reserved
65 PS2 Mouse special Special treatment to PS2 Mouse port
66 Reserved
67 ACPI init ACPI sub-system initializing
68 Reserved
69 Init Cache Initialize cache controller
6A Reserved
6B Setup Enter setup check and auto configuration check u p
6C Reserved
execute EISA initialization. If not, execute ISA tests
and clear EISA mode flag.
memory above 1MB.
8086 mode, page mode and clear the memory
version string and turn on all necessary CPU features
interrupt vectors.
Page 15
Code(hex) Name Description
6D Initialize Floppy Initialize floppy disk drive
6E Reserved
6F FDD install Install FDD and setup BIOS data area parameters
70 Reserved
71 Reserved
72 Reserved
73 Initialize Hard Drive Init ialize hard drive controller
74 Reserved
75 Detect HDD IDE device detection
76 Reserved
77 Detect serial ports Initialize serial ports
78 Reserved
79 Reserved
7A Detect parallel ports Initialize parallel ports
7B Reserved
7C HDD Write Protect HDD check for write protection
7D Reserved
7E Reserved
7F POST error check Check POST error and display them and ask for user
80 Reserved
81 Reserved
82 Security Check Ask password security.
83 Write CMOS Write all CMOS values b a ck to RAM and clear screen
84 Display PNP Display PNP devices
85 USB Final Init Final USB initialization
86 Reserved
87 Reserved
88 Reserved
89 Setup ACPI tables Setup ACPI table s
8A Reserved
8B Option ROM Detect Scan for Option ROMs
8C Reserved
8D Enable Parity Check Enable Parity Check
8E Reserved
8F IRQ12 Enable Enable IRQ12 if mouse present
90 Reserved
91 Reserved
92 Reserved
93 Boot Medium Read Detect and store boot partition head and cylinders
94 Final Init Final init for last micro details bef ore boot
95 NumLock Set Num Lock status according to Setup
96 Boot Attempt Set low stack Boot via INT 19h.
C0 Base CP U test Read/Write CPU registers
intervention
values in RAM
Page 16
Code(hex) Name Description
C1 Memory Presence Base memory detect
C2 Early Memory Board Initialization
C3 Ex tend Memory Turn on extended memory, cache initialization
C4 Sp ecial Display First display initialization
C5 Early Shadow Early shadow enable for fast boot
C6 Cache p resence External caches
FF Boot
Page 17
Loading...