Everspring Industry Co SR102 Users Manual

SR102 REMOTE TRANSMITTER

d

The Remote Transmitter is designed to control a series of O-net products, such
as EZ Alarm (SE131), On/Off Receiver (AN121, B410N) and Dimmer Receiver
(AD121, B410D), serving as a multipurpose remote controller. It is equipped with
7 sets of ID codes, therefore, each set of them is capable of controlling limitless
receivers.

LOADING THE BATTERY

1. Remove the battery cover. Fit the 3V Lithium battery in the compartment
provided with +v terminal facing upwardly . (Fig. 1)

Fig. 1

2. By pressing any key, the red LED will illuminate, which implies that the
battery has been inserted properly.

3. Replace the battery cover.

SETTING THE HOUSE CODE

The Transmitter incorporates 4 buttons and a 4-position house code slide switch.
The 4-position house code slide switch ranges from A to D. (Fig. 2) When
controlling EZ alarm (SE131), the house code slide switch has to be set in “A”
position, while “B”, “C” and “D” positions are designed for use with On/Off
Receiver (AN121, B410N), Dimmer Receiver (AD121, B410D), Lantern Receiver
(ED102) and forthcoming O-net series products.

4-position house code slide switch coupled with 4 buttons may formulate 7 sets of

ID codes, every of which is controllable to numerous receivers.

1. Setting the house code slide switch to “A” can operate EZ alarm (SE131).

House Code Position “A”

Button
No. of ID ID1 ID1 ID1 ID1

When switching to the “A” position which is situated in the orange background of
plate, simply follow its orange track for operating (instant arm), (delay
arm), (chime) and (disarm) modes.

2. Setting the house code slide switch to “B”, “C” or “D” position can take control
of On/Off Receiver (AN121, B410N), Dimmer Receiver (AD121, B410D) and
Lantern Receiver (ED102).

House Code Position “B” “C” “D”

1st. set of On, Off button ID2 ID4 ID6
2nd set of On, Off button ID3 ID5 ID7

4 buttons are divided into two sets, consisting of one pc each of On and Off
button. (Fig. 2)

Fig. 2 Fig. 3

1st. set

n

2

. set

House
code
slide
switch

Note: Write down each designated lighting fixture in each group by adopting the

sticker affixed on the rear cover. (Fig. 3)

1

EMITTING THE ID CODE

In order to communicate with the EZ Alarm (SE131), ON/OFF Receiver
(AN121,B410N) and Dimmer Receiver (AD121,B410D), it is essential that the
same ID code is used between the Receiver and Transmitter.

Set the Receiver to the ID code learning mode. Press and hold the “OFF or
button” on the Remote for 3 seconds until the LED extinguishes will emit the ID
code to the receivers, subject to house code slide switch being set at the right
position as mentioned below. The procedure of learning the ID code by the
Receiver is clearly described on the Receiver’s manual.

OPERATION

1. To work with the EZ Alarm (SE131), set House code slide switch to the “A”
position:

Remote’s operating status Remote’s RF

transmission
Press the button Instant arm Instant
Press the button Delay arm Delay
Press the button Chime Chime
Press the button Disarm/Learn (press

and hold for 3 seconds)

a. The LED will illuminate each time the button is pressed.
b. The length of time to press the button may decide what kind of RF

signal will be sent to the Receivers. Press the button, an off radio
signal will be emitted. Press and hold the button for more than 3
seconds until the LED extinguishes, a code learning command will be
transmitted.

2. To be compatible with On/Off Receiver (AN121, B410N), Dimmer Receiver
(AD121, B410D) and Lantern Receiver (ED102), set the house code slide
switch to “B”, “C” or “D” position.

EZ Alarm operating
status

Off/Learn

Remote’s
operating status

Press 1st. set of
On button
Press 1st. set of
Off button
Press 1st. set of
On & Off button
simultaneously
for more than 3
seconds
Press 2nd. set of
On button
Press 2nd. set of
Off button
Press 2nd. set of
On & Off button
simultaneously
for more than 3
seconds

a. Lock compulsorily

Pressing 1
will emit lock command to On/Off Receiver/Dimmer Receiver which will stop
receiving signal from any other devices. However, lock command can be
released by pressing “on” button on the Remote Transmitter or pressing the
ON/OFF knob on the On/Off Receiver/Dimmer Receiver directly.

b. Pressing the “OFF” button will emit off signal to turn off the lighting fixture

connected to the On/Off Receiver (AN121, B410N) or Dimmer Receiver
(AD121, B410D), whereas the code learning command will be transmitted by
pressing the “OFF” button for more than 3 seconds until the LED
extinguishes.

2

Remote’s RF
transmission

On On Dimmer On,
Off/Learn Off Dimmer Off
Lock Lock compulsorily

On On Dimmer On,
Off/Learn Off Dimmer Off
Lock Lock compulsorily

st

. set of On & Off button simultaneously for more than 3 seconds

On/Off Receiver’s
(AN121, B410N)

Operating status

(refer to ”a” as
mentioned below)

(refer to “a“ as
mentioned below)

Dimmer
Receiver’s
(AD121, B410D)
operating status

Start/Stop

Lock compulsorily
(refer to “a” as
mentioned below)

Start/Stop

Lock compulsorily
(refer to “a” as
mentioned below)