Everpure H-54, H-300, H-104, H-300-HSD, H-300-NXT Instruction Manual

...

H SERIES WATER FILTRATION SYSTEMS SISTEMA DE FILTRACIÓN DE AGUA DE LA SERIE H H SÉRIE SYSTÈME DE FILTRAGE D’EAU

INSTALLATION INSTRUCTIONS  ENGLISH

Product Specifications ........................................... Page 3

Tools Required ....................................................... Page 4

Basic Installation Instructions ............................... Page 4

H-1200 Installation Instructions .......................Pages 6-7

Claims & Notes ...................................................... Page 7

INSTRUCCIONES DE INSTALACIÓN  ESPAÑOL

Especificaciones Del Producto ......................... Página 14

Herramientas necesarias ................................. Página 15

Instrucciones básicas de instalación................ Página 15

H 1200 Instrucciones de instalación .......... Páginas 17-18

Declaraciones y notas ....................................... Página 18

INSTRUCTIONS D’INSTALLATION  FRANÇAIS

Caractéristiques Techniques Du Produit ............. Page 25

Outils nécessaires ............................................... Page 26

Instructions d’installation de base ...................... Page 26

Consignes d’utilisation pour l’H 1200 ...........Pages 28-29

Revendication & remarques ................................ Page 29

Thank you for purchasing an Everpure§ commercial-grade water filtration system for your home. With your Everpure system, you get premium quality water direct from your tap that’s great-tasting, healthful and convenient for you and your family.

Product Specifications:

•For Cold Water Use Only

•Temperature Range: 35-100°F (2-38°C)

•Min.-Max. Working Pressure: 10-125 psi (0.7-8.6 bar)

•Service Flow Rate: 0.5 gpm (1.9 Lpm)

THE OWNER’S GUIDE IS APPLICABLE FOR THE FOLLOWING

Model H-54 Rated Capacity: 750 gal (2,839 L) Model H-300 Rated Capacity: 300 gal (1,136 L) Model H-104 Rated Capacity: 1,000 gal (3,785 L) Model H-300-HSD Rated Capacity: 300 gal (1,136 L) Model H-300-NXT Rated Capacity: 300 gal (1,136 L) Model H-1200 Rated Capacity: 1,000 gal (3,785 L)

†

For optimum performance, cartridge replacement is

EVERPURE FILTER MODELS:

†

required once a year, or sooner if flow becomes too slow for convenience, or if the unit’s rated capacity is reached.

For purchase of replaceable components, please contact your local distributor. H-1200 customers: Instructions for installing the H-1200

begin on page 6 of this Installation and Operation Guide.

The Universal Plumbing Code adopted by over 20 states, and other specific state and county codes, prohibit the use of saddle valves and their use is never recommended. You must adhere to your state/local plumbing codes. Consult your licensed plumber if you have related questions.

Do NOT use copper tubing with the John Guest Fittings provided with your Everpure Filter System. Copper tubing may appear to fit, but water leaks will develop over time and use. If copper tubing is required, you must use copper compression fittings available from any hardware/plumbing supply.

CALIFORNIA PROPOSITION 65 WARNING

State of California to cause cancer or birth defects or other reproductive harm.

Multiple Appliance Connections: You can also connect your

Everpure Filter to the refrigerator for ice and water, an instant hot water dispenser or chiller, or a plumbed-in coffee brewer. Simply install connection “tees” (available from any hardware/ plumbing supply) in the water line between the filter and the faucet adaptor, and run new tubing to each appliance.

NOTE:

used.

NOTE:

should be treated to remove chlorine prior to entering filter. NOTE:

These appliances require flow and volume beyond the design limits of your under-sink filter system.

NOTE:

faucet connection under the sink, a flush valve is required.

This product contains chemicals known to the

Spent adsorption media will not be regenerated and

If adsorption media is affected by chlorine, water supply

DO NOT connect this system to a commercial ice maker.

If connecting to a home ice maker and there is no filter

ENGLISH

EVERPURE H-Series Water Filtration Systems • 3

BASIC INSTALLATION INSTRUCTIONS

Tools Needed For Installation

• #2 Phillips Screwdriver • Wrench • Pencil

• Utility Knife • Measuring Tape

1. OPEN CARTON & INSPECT PARTS

Installation Parts

Key Description Part No.

1 QL3 Filter Head

ENGLISH

10 Everpure Filter Timer EV314160

(incl. Qty. 2 ea of

Filter Cartridge (incl. – Model H-54 EV925268 – Model H-300 EV927072 – Model H-104 EV961211 – Model H-300-HSD EV927075

– Model H-300-NXT EV927441 3 Locking Washers 4 Screws 5 Angle Stop Valve Adaptor EV312120 6 Tubing, 1/4" poly

Elbow Fitting Pack Restrictor

(incl. Qty. 2 ea of  & )

8 Plumbers Tape EV312119 9 Faucet Connector EV312135

(2 req.)

 & )

)

(2 req.)

(per foot)

EV925831

EV306204 EV306196

A0860119 EV308168

2. VERIFY UNDERSINK MOUNTING LOCATION

Measure 22” from the base of the cabinet, and mark the mounting location for the top of the filter head. Make sure there is adequate space above the head to open and close the built-in shut off valve and to avoid crimping the water line tubing. Also, make sure your chosen location offers easy access for future cartridge changes.

22"

4 • EVERPURE H-Series Water Filtration Systems

DIMENSION Width Height Depth

H-54 5" 15" 5" H-104 5" 20" 5" H-300 5" 22" 5" H-300-HSD 5" 22" 5" H-300-NXT 5" 22" 5"

The head and cartridge must be mounted in the

NOTE:

vertical position, with the cartridge hanging down.

3. MOUNT FILTER HEAD UNDER SINK

A. Identify Filter Head and the two Elbow Fittings, and

note that the Outlet Fitting has a black band. This fitting includes a small restrictor insert to ensure maximum flow at 0.5 gpm (1.9 Lpm) per minute.

B. Apply Plumbers Tape to the threads of each Elbow

Fitting. Wrap tape in direction of the threads to assure a tight fit and avoid small leaks.

C. Screw Inlet Elbow Fitting into the left side of the

filter head, and hand tighten only.

D. Screw Outlet Elbow Fitting (black band) into the

right side of the filter head in the same manner.

E. Securely mount the filter head on the cabinet wall

using the enclosed mounting screws and washers.

4. ATTACH INLET WATER SUPPLY

F. Locate and close the cold water Angle Stop Valve

under your kitchen sink. Open cold water line of faucet to release water pressure.

G. Unscrew and disconnect the braided tubing on top of

the Angle Stop Valve.

H. Attach the bottom of Angle Stop Adaptor to the

existing cold water Angle Stop Valve.

I. Attach the braided tubing to the top of the Angle

Stop Adaptor.

J. Close side valve on Angle Stop Adaptor and open

cold water Angle Stop Valve to return water service to kitchen sink. Check for leaks.

Plumbers Tape should not be required for

NOTE:

these next steps.

K. Measure length of tubing needed to connect Angle

Stop Adaptor to Inlet Elbow Fitting on Filter Head.

Allow adequate tubing to avoid sharp turns. L. Cut tubing at a 90° angle using a sharp knife. M. Insert ends of tubing into quick-connect fittings.

Push tube into fitting and gently pull to confirm a

tight fit.

5. ATTACH FILTERED WATER TO SINK FAUCET

N. Install separate faucet for filtered drinking water.

Follow individual manufacturer’s instructions. O. Attach Faucet Connector Fitting to bottom end of

threads on new faucet assembly. Plumbers Tape

should not be required for this step. P. Measure length of tubing needed to connect the

Outlet Elbow Fitting on Filter Head to the new

Faucet Connector Fitting. Allow adequate tubing to

avoid sharp turns. Cut and insert each end of the

tubing into the fittings.

ENGLISH

EVERPURE H-Series Water Filtration Systems • 5

6. INSTALL AND FLUSH FILTER CARTRIDGE

Q. Lift handle of the built-in shut off Valve on the

Head. R. Hold Head firmly with one hand. S. Align cartridge lug with label on filter Head. T. Insert filter Cartridge – Push upwards. U. Turn it to the right – About 1⁄4 turn – Until rotation

stops. V. Open Side Valve of Angle Stop Adaptor and check

for leaks up to Inlet Elbow Fitting. W. Open Filtered Water Faucet.

ENGLISH

X. Lower handle of built-in shut off valve on the Head,

to flush water to the sink.

Flush new filter cartridges for at least 15

NOTE:

minutes to remove air and any loose carbon. At first

the water may appear cloudy due to trapped air in

the filter and tubing. If water continues to be cloudy

for more than one week, please contact Everpure

Technical Services for assistance.

Y. Activate Filter Timer by pinching bubble until you

feel a change in resistance as the filter timer “pops”.

Within a few seconds, a thin RED line will appear in

the white window showing the Timestrip has been

activated. Peel away backing and adhere to desired

location. When the white window is completely filled

with RED, it is time to replace your product.

V W

Label

Lug

H1200 INSTRUCTIONS

Tools Needed For Installation

• #2 Phillips Screwdriver

• Wrench

• Utility Knife

• Measuring Tape

• Pencil

1. OPEN CARTON & INSPECT PARTS

Installation Parts

Key Description Part No.

1 Twin Filter Head N/A 2 H-1200 Filter Cartridges

(Set of 2) (

3 Locking Washers (2 req.) EV306204 4 Screws (2 req.) EV306196 5 Angle Stop Valve Adaptor EV312120 6 Tubing, 1/4" poly (per foot) A0860119

Elbow Fitting Pack Restrictor

(incl. Qty. 2 ea of #3 & #4)

8 Plumbers Tape EV312119

9 Faucet Connector EV312135 10 Everpure Filter Timer EV314160 11 Shut Off Valve,

3/8" John Guest x 3/8" FPT

12 Coupler, 3/8" FPT

Stainless

Includes

)

EV928201

EV308168

EV309860

EV312350

6 • EVERPURE H-Series Water Filtration Systems

2. VERIFY UNDERSINK MOUNTING LOCATION

Measure 22” from the base of the cabinet, and mark the mounting location for the top of the filter head. Measure 13” for the width required for the H-1200 System with dual cartridges. Make sure there is adequate space above the head to open and close the shut-off valve and to avoid crimping the water line tubing. Also, make sure your chosen location offers easy access for future cartridge changes.

DIMENSION

H-1200 13" 22" 5"

NOTE: The head and cartridge must be mounted in the vertical position, with the cartridge hanging down.

3. MOUNT FILTER HEAD UNDER SINK

A. Identify Dual Filter Head and Shut Off Valve (EV309860). B. Apply Plumbers Tape to the threads on the inlet (left)

side of the Head. Screw on the new Shut Off Valve and hand tighten. Repeat for the Stainless Coupler (EV312350) for the outlet (right) side of the Head.

C. Apply Plumbers Tape to the threads of the Outlet

Elbow Fitting (black band). Screw into the outlet of the Stainless Coupler. Wrap tape in direction of the threads to assure a tight fit and avoid small leaks.

D. Securely mount the filter head on the cabinet wall

using the enclosed mounting screws and washers.

4. Go to page 5 and follow Basic Installation Instructions, Steps 4, 5, and 6, to complete the H-1200 System installation.

Width Height Depth

ENGLISH

22"

Dual Filter Head Shut Off Valve

CLAIMS & NOTES

This installation must comply with all applicable state and local regulations.

Do not use with water that is microbiologically unsafe or unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on waters that may contain filterable cysts.

Spent adsorption media will not be regenerated and used. If adsorption media is affected by chlorine, water supply

should be treated to remove chlorine prior to entering filter.

Testing was performed under standard laboratory conditions, actual performance may vary.

EPA Est. No. 002623-IL-002

The H-54, H-300, H-104, H-300-HSD, & H-1200 are Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42 and 53 for the claims

C US

specified on the Performance

The H-300-NXT is Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42, 53 and 401 for the claims specified on the Performance Performance

Data Sheet.

EVERPURE H-Series Water Filtration Systems • 7

H-104 Cartridge - Part No. EV9612-11, EV9612-16

PERFORMANCE DATA SHEET

EVERPURE

H-104 DRINKING WATER SYSTEMS

IMPORTANT NOTICE: Read this Performance Data Sheet and

ENGLISH

compare the capabilities of this unit with your actual water treatment needs. It is recommended that, before purchasing a water treatment unit, you have your water tested to determine your actual treatment needs.

FEATURES

cooking.

• Reduces chlorine taste and odor.

manganese, and sulfides.

• NSF/ANSI Standard 53 certified to reduce cysts such as Cryptosporidium and Giardia by mechanical means.

• Reduces common earthy, moldy, fishy tastes and odors.

• Reduces lead to below the Federal Action Level.

• Enhanced with KDF media to inhibit scale build-up that can damage equipment.

• Reduces particles as small as 0.5 micron in size by mechanical means.

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF/ANSI*

This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the sy to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Substance

Standard 42—Aesthetic Effects

Chlorine 2.0 mg/L ± 10% ° 50% 87.8%

Particulate, Class I particles 0.5 to <1 µm

Standard 53—Health Effects

Cyst Minimum 50,000/L 99.95%

Lead 8.5 0.15 mg/L ± 10% 0.010 mg/L 99.3% 99.3%

Lead 6.5 0.15 mg/L ± 10% 0.010 mg/L 98.7% 99.3%

Inﬂuent Challenge

Concentration

at least 10,000

particles/mL

Max. Permissible Product

Water Concentration

stem was reduced

Reduction

Requirements

Minimum

Reduction

° 85% 98.8%

99.99% 99.99%

dna gniknird rof ytilauq muimerp ot retaw detaert sehsilop yleniF •

,nori dezidixo sa hcus setalucitrap rehto dna tsur ,trid secudeR •

Average

Reduction

GENERAL INSTALLATION/OPERATION/MAINTENANCE REQUIREMENTS

gnidulcni )mc 15 x 31 x 31( .ni 02 x 5 x 5 :deriuqer ecapS •

2½ inches of clear space under unit for cartridge change.

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush new cartridge at full flow for three minutes to purge air. semoceb wolf nehw ro ,dehcaer si yticapac nehw segdirtrac ecalpeR •

too slow, but at least annually.

SPECIAL NOTICES

• Installation instructions, parts and service availability, and standard

warranty are included with the product.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter cartridges. Suggested retail $122.99.

• Do not use with water that is microbiologically unsafe or of unknown

quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by this

water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions, actual performance

may vary.

• Spent adsorption media will not be regenerated and used.

• If adsorption media is affected by chlorine, water supply should be

treated to remove chlorine prior to entering filter.

System Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42 and 53 for the claims

C US

specified on the Performance Data Sheet.

*Tested using ﬂow rate = 0.5 gpm; pressure = 60 psig; pH = 7.5 ± 0.5; temp. = 20° ± 2.5°C

OPERATING SPECIFICATIONS

• Capacity: 1,000 gallons (3,780L)

• Pressure requirement: 10-125 psi (0.7 - 8.6 bar), non-shock

• Temperature: 35-100°F (2°-38°C)

• Flow Rate: 0.5 gpm (1.9 Lpm)

EPA Est. 002623-IL-002

8 • EVERPURE H-Series Water Filtration Systems

EV309529 REV H DE17

EVERPURE

H-54 Cartridge - Part No. EV9730-06, EV9252-68, EV9252-66, EV9252-67

PERFORMANCE DATA SHEET

ENGLISH

IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs. It is recommended that, before purchasing a water treatment unit, you have your water tested to determine your actual treatment needs.

FEATURES

dna gniknird rof ytilauq muimerp ot retaw detaert sehsilop yleniF •

cooking.

• Reduces chlorine taste and odor. ,nori dezidixo sa hcus setalucitrap rehto dna tsur ,trid secudeR •

manganese, and sulfides.

• NSF/ANSI Standard 53 certified to reduce cysts such as

Cryptosporidium and Giardia by mechanical means.

• Adsorbs common earthy, moldy, fishy tastes and odors.

• Reduces lead to below the Federal Action Level of 10 ppb.

• Enhanced with KDF media to inhibit scale build-up that can damage

equipment.

• Reduces particles as small as 0.5 micron in size by mechanical

means.

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF/ANSI*

This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Substance

Standard 42—Aesthetic Effects

Chlorine 2.0 mg/L ± 10% ≥ 50% 86.8%

Particulate, Class I particles 0.5 to <1 µm

Standard 53—Health Effects Cyst Minimum 50,000/L 99.95% 99.99% 99.99%

Lead 8.5 0.15 mg/L ± 10% 0.010 mg/L 98.7% 99.3%

Lead 6.5 0.15 mg/L ± 10% 0.010 mg/L 99.3% 99.3%

*Tested using ﬂow rate = 0.5 gpm; pressure = 60 psig; pH = 7.5 ± 0.5; temp. = 20° ± 2.5°C

Inﬂuent Challenge

Concentration

at least 10,000

particles/mL

Max. Permissible Product

Water Concentration

Reduction

Requirements

≥ 85% 98.8%

reduced

Minimum

Reduction

Average

Reduction

GENERAL INSTALLATION/OPERATION/MAINTENANCE REQUIREMENTS

sehcni ½-2 gnidulcni )mc 83 x 31 x 31( .ni 51 x 5 x 5 :deriuqer ecapS •

of clear space under unit for cartridge change.

• Install vertically with cartridge hanging down.

• Use minimum length of tubing possible.

• Flush new cartridge at full flow for three minutes to purge air. semoceb wolf nehw ro ,dehcaer si yticapac nehw segdirtrac ecalpeR •

too slow, but at least annually.

SPECIAL NOTICES

• Installation instructions, parts and service availability, and standard

warranty are included with the product when shipped.

• This drinking water system must be maintained according to

manufacturer’s instructions, including replacement of filter cartridges. Suggested list price: $100.99.

• Do not use with water that is microbiologically unsafe, or of unknown

quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

• The contaminants or other substances removed or reduced by this

water treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

• Tested under standard laboratory conditions, actual performance

may vary.

• Spent adsorption media will not be regenerated and used.

• If adsorption media is affected by chlorine, water supply should be

treated to remove chlorine prior to entering filter.

System Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42 and 53 for the claims

C US

specified on the Performance Data Sheet.

OPERATING SPECIFICATIONS

• Capacity: 750 gallons (2,839L)

• Pressure requirement: 10-125 psi (0.7 - 8.6 bar), non-shock

• Temperature: 35-100°F (2°-38°C)

• Flow Rate: 0.5 gpm (1.9 Lpm)

EPA Est. 002623-IL-002

EV309537 REV H DE17

EVERPURE H-Series Water Filtration Systems • 9

EVERPURE

H-300 Cartridge - Part Nos. EV9270-71, EV9270-72

PERFORMANCE DATA SHEET

H-300 DRINKING WATER SYSTEM

IMPORTANT NOTICE: Read this Performance Data Sheet and

ENGLISH

FEATURES

• Finely polishes treated water to premium quality for drinking and cooking.

• Reduces chlorine taste and odor.

• Reduces dirt, rust and other particulates such as oxidized iron, manganese, and sulfides.

• NSF/ANSI Standard 53 certified to reduce cysts such as Cryptosporidium and Giardia by mechanical means.

• Controls even extreme levels of common “off” tastes and odors, including those which are earthy, moldy and fishy.

• Reduces lead to below the Federal Action Level.

• Effectively reduces Volatile Organic Chemicals (VOCs), including Trihalomethanes (THMs).

• Enhanced with KDF media to inhibit scale build-up that can damage equipment.

• Reduces particles as small as 0.5 micron in size by mechanical means.

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF/ANSI*

This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Substance

Standard 42—Aesthetic Effects

Chlorine 2.0 mg/L ± 10% ≥ 50% 86.8%

Particulate, Class I particles 0.5 to <1 µm

Standard 53—Health Effects Cyst Minimum 50,000/L 99.95% 99.99% 99.99%

Lead 6.5 0.15 mg/L ± 10% 0.010 mg/L 99.3% 99.3%

Lead 8.5 0.15 mg/L ± 10% 0.010 mg/L 98.7% 99.3%

Chloroform 0.300 mg/L 0.015 mg/L 95.8% 98.9%

(VOC surrogate chemical)

*Tested using ﬂow rate = 0.5 gpm; pressure = 60 psig; pH = 7.5 ± 0.5; temp. = 20° ± 2.5°C

Inﬂuent Challenge

Concentration

at least 10,000

particles/mL

EPA Est. 002623-IL-002

The H-300 is Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42 and 53 for the

C US

NOTE:

claims specified on the Performance

Spent adsorption media will not be regenerated and used. If adsorption media is affected by chlorine, water supply should be treated to remove chlorine prior to entering filter.

Max. Permissible Product

Water Concentration

Reduction

Requirements

Minimum

Reduction

≥ 85% 98.8%

Data Sheet.

Average

Reduction

OPERATING SPECIFICATIONS

• Capacity: 300 gallons (1,135L)

• Pressure requirement: 10-125 psi (0.7 - 8.6 bar), non-shock

• Temperature: 35-100°F (2-38°C)

• Flow Rate: 0.5 gpm (1.9 Lpm)

Performance Data Sheet Reduction Claims for Organic Chemicals Included by Surrogate Testing

Substance

alachlor 0.050 0.001 atrazine 0.100 0.003 benzene 0.081 0.001 carbofuran 0.190 0.001 carbon tetrachloride 0.078 0.0018 chlorobenzene 0.077 0.001 chloropicrin 0.015 0.0002 2,4-D 0.110 0.0017 dibromochloropropane (DBCP) 0.052 0.00002 o-dichlorobenzene 0.080 0.001 p-dichlorobenzene 0.040 0.001 1,2-dichloroethane 0.088 0.0048 1,1-dichloroethylene 0.083 0.001 cis-1,2-dichloroethylene 0.170 0.0005 trans-1,2-dichloroethylene 0.086 0.001 1,2-dichloropropane 0.080 0.001 cis-1,3-dichloropropylene 0.079 0.001 dinoseb 0.170 0.0002 endrin 0.053 0.00059 ethylbenzene 0.088 0.001 ethylene dibromide (EDB) 0.044 0.00002 haloacetonitriles (HAN):

bromochloroacentonitrile dibromoacetonitrile dichloroacetonitrile trichloroacetonitrile

haloketones (HK): 1,1-dichloro-2-propanone 1,1,1-trichloro-2-propanone

heptachlor 0.025 0.00001 heptachlor epoxide 0.0107 0.0002 hexachlorobutadiene 0.044 0.001 hexachlorocyclopentadiene 0.060 0.000002 lindane 0.055 0.00001 methoxychlor 0.050 0.0001 pentachlorophenol 0.096 0.001 simazine 0.120 0.004 styrene 0.150 0.0005 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethylene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP(silvex) 0.270 0.0016 tribromoacetic acid 0.042 0.001 1,2,4-trichlorobenzene 0.160 0.0005 1,1,1-trichlor 1,1,2-trichloroethane 0.150 0.0005 trichloroethylene 0.180 0.001 trihalomethanes (includes):

chloroform (surrogate chemical) bromoform bromodichloromethane chlorodibromomethane xylenes (total) 0.070 0.001

oethane 0.084 0.0046

Influent Challenge Concentration mg/L

0.022

0.024

0.0096

0.015

0.0072

0.0082

0.300

Maximum permissible Product Water Concentration mg/L

0.0005

0.0006

0.0002

0.0003

0.0001

0.0003

0.015

10 • EVERPURE H-Series Water Filtration Systems

EV310316 REV L DE17

PERFORMANCE DATA SHEET

EVERPURE

H-1200 Cartridge - Part Nos. EV9282-01, EV9282-03

IMPORTANT NOTICE: Read this Performance Data Sheet and

FEATURES

• Finely polishes treated water to premium quality for drinking and cooking.

• NSF/ANSI Standard 53 certified to reduce cysts such as Cryptosporidium and Giardia by mechanical means.

• Reduces dirt, rust and other particulates sulfides (oxidized iron and manganese - As tested by Everpure).

• Controls even extreme levels of common “off” tastes and odors, including those which are earthy, moldy, and fishy.

• Reduces lead to below the Federal Action Level of 15 ppb.

• Effectively reduces volatile organic chemicals (VOCs), including trihalomethanes (THMs).

• Effectively reduces methyl tertiary-butyl ether (MTBE).

• Enhanced with KDF media to inhibit scale build-up that can damage equipment.

• Reduces particles as small as 0.5 micron in size by mechanical means.

HEALTH CLAIM PERFORMANCE CERTIFIED BY NSF/ANSI*

This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.

Substance

Standard 42—Aesthetic Effects

Chlorine 2.0 mg/L ± 10% ≥ 50% 86.8%

Chloramine 3.0 mg/L ± 10% 0.5 mg/L 98.3%

Particulate, Class I particles 0.5 to <1 µm

Standard 53—Health Effects Cyst Minimum 50,000/L 99.95% 99.99% 99.99%

Lead 6.5 0.15 mg/L ± 10% 0.010 mg/L 99.3% 99.3%

Lead 8.5 0.15 mg/L ± 10% 0.010 mg/L 98.7% 99.3% Methyl tert-

butyl ether Chloroform 0.300 mg/L 0.015 mg/L 99.8% 99.8%

(VOC surrogate chemical)

*Tested using ﬂow rate = 0.5 gpm; pressure = 60 psig; pH = 7.5 ± 0.5; temp. = 20° ± 2.5°C

Inﬂuent Challenge

Concentration

at least 10,000

particles/mL

0.015 mg/L ± 20% 0.005 mg/L 73.5% 90.2%

EPA Est. 002623-IL-002

The H-1200 is Tested and Certified by NSF International against CSA B483.1 and NSF/ANSI 42

C US

and 53 for the claims specified on the Performance Data Sheet.

Max. Permissible Product

Water Concentration

Reduction

Requirements

Minimum

Reduction

≥ 85% 98.8%

Average

Reduction

H-1200 DRINKING WATER SYSTEM

OPERATING SPECIFICATIONS

• Capacity: 1,000 gallons (3,780L)

• Pressure requirement: 10-125 psi (0.7 - 8.6 bar), non-shock

• Temperature: 35-100°F (2-38°C)

• Flow Rate: 0.5 gpm (1.9 Lpm)

Performance Data Sheet Reduction Claims for Organic Chemicals Included by Surrogate Testing

Substance

bromochloroacentonitrile dibromoacetonitrile dichloroacetonitrile trichloroacetonitrile

haloketones (HK): 1,1-dichloro-2-propanone 1,1,1-trichloro-2-propanone

heptachlor 0.080 0.0004 heptachlor epoxide 0.0107 0.0002 hexachlorobutadiene 0.044 0.001 hexachlorocyclopentadiene 0.060 0.000002 lindane 0.055 0.00001 methoxychlor 0.050 0.0001 pentachlorophenol 0.096 0.001 simazine 0.120 0.004 styrene 0.150 0.0005 1,1,2,2-tetrachloroethane 0.081 0.001 tetrachloroethylene 0.081 0.001 toluene 0.078 0.001 2,4,5-TP(silvex) 0.270 0.0016 tribromoacetic acid 0.042 0.001 1,2,4-trichlorobenzene 0.160 0.0005 1,1,1-trichlor 1,1,2-trichloroethane 0.150 0.0005 trichloroethylene 0.180 0.001 trihalomethanes (includes):

chloroform (surrogate chemical) bromoform bromodichloromethane chlorodibromomethane xylenes (total) 0.070 0.001

oethane 0.084 0.0046

Influent Challenge Concentration mg/L

0.022

0.024

0.0096

0.015

0.0072

0.0082

0.300

Maximum permissible Product Water Concentration mg/L

0.0005

0.0006

0.0002

0.0003

0.0001

0.0003

0.015

ENGLISH

NOTE:

Spent adsorption media will not be regenerated and used. If adsorption media is affected by chlorine, water supply should be treated to remove chlorine prior to entering filter.

EV310543 REV M DE17

EVERPURE H-Series Water Filtration Systems • 11

+ 25 hidden pages