Page 1 of 1
Components
01. Mounting Bracket w/Green Screw
02. Outlet Box Mounting Screws
03. Plastic Anchors
04. Wood Screws
05. Mounting Screws
06. Hex Nuts (8/32)
07. Cylinder Nuts
08. Safety Cable w/Hook
09. Fixture Canopy
10. Turn Buckle
11. Chain Link 12. Chain Link
13. Lead Wire 14. Chains
15. Loops (1/8IP)
16. Loops (1/8IP)
17. Couplers (Dual-Head 1/8IP)
18. Rods
19. Couplers (Dual-Head 1/8IP)
20. Rods
21. Couplers (Dual-Head 1/8IP)
22. Rods
23. Fixture
24. Decor Rod-A
25. Decor Rod-B
26. Decor Rod-C
27. Decor Rod-D
28. Assembling Hole
1. Pass Lead Wire (13) from top of Fixture (23) through Rod (22), Coupler (21), Rod (20), Coupler (19), Rod (18), Coupler (17) and Loop (16), then
screw all of them together. After that, repeat the same assembling steps for another side without wiring. Note: The Fixture Height can be
adjusted by varying the number of rods or chain used in the assembly.
2. Pass Lead Wire (13) thru one Chain Link (12), Chain (14), another Chain Link (11), Loop (15) from Fixture Canopy (09). Finally, connect all of
them together. After that, repeat the same assembling steps for another side without wiring.
3. Find appropriate threaded holes on Mounting Bracket (01), then assemble Mounting Bracket (01) to mounting surface using hardware
suitable for material of mounting surface. Mark position of holes on mounting surface before using provided Plastic Anchors (03), drill
appropriate holes and assemble as illustrated.
4. Find appropriate threaded holes on Mounting Bracket (01), and assemble Mounting Screws (05) into threaded holes with Hex Nuts (06).
5. Attach Mounting Bracket (01) to Outlet Box with Outlet Box Mounting Screws (02), and to mounting surface with Wood Screws (04)
tightly.
6. Raise whole Fixture Canopy (09) toward outlet box, then hang it onto Mounting Bracket (01) with Safety Cable w/Hook (08) as the illustration
shown. Note: This will allow for fixture to be supported while wire connections are made.
7. Connect fixture ground wire to the outlet box ground wire with wire connector supplied; connect the common wire of the lamp cord to the
power supply white wire with wire connector supplied; connect supply wire of the lamp cord to the power supply black wire with wire connector
supplied. Note: This fixture is wired using 2 conductor Lamp cord. The insulation between the two conductors on the lamp cord can be split down
the center for better access to the two conductors. The common wire on the lamp cord is identified as the conductor with ribs embossed in the
rubber wire insulation.
8. Push Canopy (09) to ceiling, carefully passing Mounting Screws (05) through holes in Fixture Canopy (09), then verify all wires are securely
inside Fixture Canopy (09). Finally, secure fixture to ceiling with Cylinder Nuts (07).
9. Insert Decor Rod-A (24), Decor Rod-B (25), Decor Rod-C (26) and Decor Rod-D (27) into Assembling Holes (28) of Fixture (23) Decor Trim in
order as the illustration shown. Note: one extra piece of each size Decor Rod included in the parts bag.
Note 1: If fixture is to be mounted close to the ceiling, the decorative rods will need to be inserted prior to mounting fixture to the ceiling in
order to have room to insert them into the fixture.
Note 2: If the fixture is not leveled after hung, please adjust (screw) the Turn Buckle (10) up or down to help it.
ASSEMBLY AND INSTALLATION INSTRUCTIONS for the Fixture
1. Remove the fixture, parts and all mounting hardware bags (orange) from the carton and verify that all parts are present according to the illustration sheet. All parts must be
used as indicated. Do not replace any parts, leave any parts out, or use any parts which are worn out or broken. Failure to follow the instructions could cause a hazardous
situation, voids the warranty and violates the U.L. listing of the fixture.
2. To prevent the electric shock, turn off the main power at the circuit breaker before installing the fixture. NEVER attempt to install, clean or replace bulbs without shutting
off the electricity to the fixture.
3. Never use light bulbs with wattage ratings that exceed the fixtures maximum rating. Always make sure the electric current is turned off before changing the bulbs.
4. If you experience difficulties installing the lighting fixture or it fails to work as expected, please contact a local qualified licensed electrical contractor.
5. Please contact your local Capital Lighting Fixture reseller with any assembly or installation questions. Your local reseller can also provide you with replacement parts for your
new fixture.
Important Safety information (Please read before proceeding)
Assembly Instructions for the Fixture
Loading...