EVERLIGHT EVL 23-23B/R6GH Datasheet

1

www.everlight.com

SMD  B 23-23B/R6GHBHC-A01/2A

Features

․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version.

Description

․The 23-23B SMD LED is much smaller than lead frame type components, thus enable smaller board ize,

higher packing density, reduced storage space and finally smaller equipment to be obtained.

․Besides, lightweight makes them ideal for miniature applications. etc.

Applications

․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use.

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

2

www.everlight.com

Device Selection Guide

Chip Chip Type Materials

Emitted Color

Resin Color

R6 AlGaInP

Brilliant Red

Water Clear GH InGaN

Brilliant Green

BH InGaN

Blue

Absolute Maximum Ratings (Ta=25℃)

Parameter

Symbol

Rating

Unit

Reverse Voltage

VR 5 V

Forward Current

IF

R6：25 GH：20 BH：20

mA

Peak Forward Current (Duty 1/10 @1KHz)

IFP

R6：60 GH：75 BH：75

mA

Power Dissipation

Pd

R6：60 GH：95 BH：95

mW Operating Temperature

T

opr

-40 ~ +85

℃

Storage Temperature

Tstg

-40 ~ +90

℃

Electrostatic Discharge

ESD

HBM

R6：2000 GH：150 BH：150

V

Soldering Temperature

T

sol

Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec.

Electro-Optical Characteristics (Ta=25℃)

Parameter

Symbol

Min.

Typ.

Max.

Unit

Condition

Luminous Intensity

Iv

R6：72 GH：140 BH：45

100 200 65

-----

mcd

IF =20mA Viewing Angle

2θ

1/2

-----

130

-----

deg

IF =20mA

Peak Wavelength

λ p

R6：----GH：----BH：-----

632 518 468

-----

nm

IF =20mA

Dominant Wavelength

λ d

R6：----GH：----BH：-----

624 525 470

-----

nm

IF =20mA

Spectrum Radiation Bandwidth

△λ

R6：----GH：----BH：-----

20 35 25

-----

nm

IF =20mA

Forward Voltage

VF

R6：1.7 GH：2.7 BH：2.7

2.0

3.3

2.4

3.7

V

IF =20mA

Reverse Current

IR

R6：----- GH：----BH：-----

-----

10

50 50

μA

VR =5V

Note:

Tolerance of Luminous Intensity: ±11%

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

3

www.everlight.com

Typical Electro-Optical Characteristics Curves R6

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

4

www.everlight.com

Typical Electro-Optical Characteristics Curves GH

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

5

www.everlight.com

Typical Electro-Optical Characteristics Curves

BH

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

6

www.everlight.com

Package Outline Dimensions

Note: Tolerances unless mentioned ±0.1mm. Unit = mm

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

7

www.everlight.com

‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity ‧CAT: Luminous Intensity Rank ‧HUE: Chromaticity Coordinates & Dom. Wavelength Rank ‧REF: Forward Voltage Rank ‧LOT No: Lot Number

RoHS

Pb

CPN : P N : XXXXXXXXXXXXX

XXXXXXXXXXXXX

QTY : XXX

LOT NO : XXXXXXXXXX

Reference : XXXXXXXX

CAT : XXX HUE : XXX REF : XXX

EVERLIGHT

MADE IN TAIWAN

Moisture Resistant Packing Materials

Label Explanation

Reel Dimensions

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

8

www.everlight.com

Label

Desiccant Label

Aluminum moisture-proof bag

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Moisture Resistant Packaging

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

9

www.everlight.com

Pre-heating 150~200°C

60~120sec.

Above 217°C 60~150sec.

260°C Max.

10sec. Max.

6°C/sec.Max.

Above255°C 30sec.Max.

3°C/sec.Max.

Precautions For Use

1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.

If unused LEDs remain, it should be stored in moisture proof packages.

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the

soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

DATASHEET SMD  B 23-23B/R6GHBHC-A01/2A

10

www.everlight.com

Application Restrictions

High reliability applications such as military/aerospace, automotive safety/security systems, and medical equipment may require different product. If you have any concerns, please contact Everlight before using this product in your application. This specification guarantees the quality and performance of the product as an individual component. Do not use this product beyond the specification described in this document.

EVERLIGHT EVL 23-23B/R6GH Datasheet

Specifications and Main Features

Frequently Asked Questions

User Manual