EVERLIGHT EVL 17-21/R6C-A Datasheet

EVERLIGHT ELECTRONICS CO., LTD.

Technical Data Sheet
0805 Package Chip LED (1.1mm Height)

17-21/R6C-AP1Q2L/3T

Features

․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free

․Rohs refer to SMD B Type SGS report

Descriptions

․The 17-21 SMD Taping is much smaller

than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications, etc.

Applications

․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.
․General use.

Device Selection Guide

PART No.

Material Emitted Color

17-21/R6C-AP1Q2L/3T AlGaInP Brilliant Red Water Clear

Chip

Lens Color

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 1 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Package Outline Dimensions

-

Note: The tolerances unless mentioned are ±0.1, unit = mm.

+

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 2 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit
Reverse Voltage
Forward Current

V

R

I

F

Operating Temperature Topr -40 ~ +85

Storage Temperature Tstg -40 ~ +90

Electrostatic Discharge ESD 2000 V

Power Dissipation

P

d

Peak Forward Current

I

FP

(Duty 1/10 @1KHz)

Soldering Temperature Tsol

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Min. Typ. Max. Unit Condition

5 V

25 mA

℃
℃

60 mW

60 mA

Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.

Luminous Intensity

I

V

45.0 ----- 112.0

Peak Wavelength λp ---- 632 ---- nm

Dominant Wavelength

λd

617.5 ----- 633.5

Spectrum Radiation

Bandwidth

△λ

---- 20 ----

Viewing Angle 2θ1/2 ---- 120 ---- deg

Forward Voltage V

Reverse Current I

F 1.70 ---- 2.30

R

---- ---- 10 μA

Notes:

1.Tolerance of Luminous Intensity ±10%

2.Tolerance of Dominant Wavelength ±1nm

3.Tolerance of Forward Voltage ±0.05V

mcd

nm

nm

V

=20mA

I

F

=5V

V

R

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 3 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Bin Range Of Dom. Wavelength

Group

A

Bin Min Max

E4 617.5 621.5
E5 621.5 625.5
E6 625.5 629.5
E7 629.5 633.5

Bin Range Of Luminous Intensity

Bin Min Max Unit Condition

P1 45.0 57.0

P2 57.0 72.0
Q1 72.0 90.0
Q2 90.0 112

Bin Range Of Forward Voltage

Unit

nm IF=20mA

Condition

mcd I

=20mA

F

Groups Bin Min Max Unit Condition

19 1.70 1.80
20 1.80 1.90

L

21 1.90 2.00

V IF=20mA

22 2.00 2.10
23 2.10 2.20
24 2.20 2.30

Notes:

1.Tolerance of Luminous Intensity ±10%

2.Tolerance of Dominant Wavelength ±1nm

3.Tolerance of Forward Voltage ±0.05V

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 4 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Typical Electro-Optical Characteristics Curves

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 5 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Label explanation

CAT: Luminous Intensity Rank

HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank

Reel Dimensions

Note: The tolerances unless mentioned are ±0.1, unit = mm.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 6 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel

Note: The tolerances unless mentioned are ±0.1, unit = mm.

Moisture Resistant Packaging

Label

Aluminum moisture-proof bag

Desiccant Label

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 7 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.
Confidence level：90%

LTPD：10%

No. Items Test Condition

Test

Hours/Cycles

Temp. : 260℃±5℃

1 Reflow Soldering

Min. 5sec.

6 Min.

H : +100℃ 15min

2 Temperature Cycle

∫ 5 min

300 Cycles

L : -40℃ 15min

H : +100℃ 5min

3 Thermal Shock

∫ 10 sec

300 Cycles

L : -10℃ 5min

4

High Temperature

Temp. : 100℃

1000 Hrs.

Storage

5

Low Temperature

Temp. : -40℃

1000 Hrs.

Storage

6 DC Operating Life IF = 20 mA

1000 Hrs.

Sample

Ac/Re

Size

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

7

High Temperature /

85℃/ 85%RH

1000 Hrs.

22 PCS. 0/1

High Humidity

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 8 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

17-21/R6C-AP1Q2L/3T

Precautions For Use

1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 9 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu

EVERLIGHT ELECTRONICS CO., LTD.

E

17-21/R6C-AP1Q2L/3T

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.

5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.

VERLIGHT ELECTRONICS CO., LTD. Tel: [phone]

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: [phone]
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com

Everlight Electronics Co., Ltd. http://www.everlight.com Rev.: 1 Page: 10 of 10
Device No: SZDSE-171-R06 Prepared date: 23-May-2005 Prepared by: Hao Liu