EVERLIGHT EVL 15-21SURC/S2 Datasheet

EVERLIGHT ELECTRONICS CO.,LTD.

Technical Data Sheet
1206 Package Chip LED

15-21SURC/S530-XX/TR8

Features

˙Package in 8mm tape on 7〞diameter reel.
˙Compatible with automatic placement equipment.-
˙Compatible with infrared and vapor phase reflow

solder process.

˙Mono-color type.

Descriptions

˙The 15-21 SMD Taping is much smaller

than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.

˙Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

˙Automotive: backlighting in dashboard and switch.
˙Telecommunication: indicator and backlighting in

telephone and fax.

˙Flat backlight for LCD, switch and symbol.
˙General use.

Device Selection Guide

Chip

Material Emitted Color

AlGaInP Hyper Red Water Clear

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 1 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

Lens Color

EVERLIGHT ELECTRONICS CO.,LTD.

Package Outline Dimensions

15-21SURC/S530-XX/TR8

Notes: Tolerances Unless Dimension ± 0.1mm, Unit = mm

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 2 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

Absolute Maximum Ratings (Ta=25℃℃℃℃)

Parameter Symbol Rating Unit

Reverse Voltage VR 5 V

Forward Current IF 25 mA

Operating Temperature Topr -40 ~ +85 ℃

Storage Temperature Tstg -40~ +90 ℃

Soldering Temperature Tsol

Electrostatic Discharge ESD

Power Dissipation Pd 60 mW

Peak Forward Current

(Duty 1/10 @1KHz)

I

F (PEAK)

260 (for 5

second)

2000

60 mA

Electro-Optical Characteristics (Ta=25℃℃℃℃)

Parameter

Symbol

*Chip

Min. Typ. Max. Unit Condition

Rank

15-21SURC/S530-XX/TR8

℃

V

Luminous Intensity Iv

Viewing Angle

Peak Wavelength

Dominant Wavele ngt h

Spectrum Radiation

Bandwidth

Forward Voltage

Reverse Current I

2θ1/2

λp

λd

△λ

V

*15-21SURC/S530-XX/TR8

A2 15 38 ----­A3 36 54 ----­A4 49 74 ----­A5 60 92 ----­A6 72 111 -----

----- ----- 140 -----

----- ----- 632 ----- nm

F

----- ----- ----- 10

R

----- ----- 624 -----

----- ----- 20 -----

----- ----- 2.0 2.4

mcd IF=20 mA

deg IF=20mA

IF=20mA
IF=20mA

IF=20mA

IF=20mA

VR=5V

nm

nm

V

μA

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 3 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

Chip Rank

EVERLIGHT ELECTRONICS CO.,LTD.

Typical Electro-Optical Characteristics Curves

15-21SURC/S530-XX/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 4 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

Label explanation

CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank

15-21SURC/S530-XX/TR8

Reel Dimensions

Note:

Tolerances Unless Dimension ± 0.1mm ,Unit = mm

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 5 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

15-21SURC/S530-XX/TR8

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note:

Tolerances Unless Dimension ± 0.1mm ,Unit = mm

Moisture Resistant Packaging

Label

Aluminum moistue-proof bag

LabelDesiccant

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 6 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

15-21SURC/S530-XX/TR8

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.
Confidence level：90%

LTPD：10%

No. Items Test Condition

Temp. : 240℃± 5℃

1 Reflow Soldering

5 sec.

H : +100℃ 15min

2 Temperature Cycle

∫ 5 min

L : -40℃ 15min

H : +100℃ 5min

3 Thermal Shock

∫ 10 sec

Hours/Cycles

300 Cycles

300 Cycles

Test

6 Min.

Sample

Ac/Re

Size

22 Pcs. 0/1

22 PCS. 0/1

22 PCS. 0/1

L : -10℃ 5min

4

High Temperature

Temp. : 100℃

Storage

5

Low Temperature

Temp. : -55℃

Storage

6 DC Operating Life IF = 20 mA

7

High Temperature /

85℃/RH85%

High Humidity

1000 Hrs.

1000 Hrs.

1000 Hrs.

1000 Hrs.

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 7 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

15-21SURC/S530-XX/TR8

Precautions For Use

1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60± 5℃ for 24 hours.

3. Soldering Condition

3.1 Lead solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 Reflow soldering should not be done more than two times.

3.4 When soldering, do not put stress on the LEDs during heating.

3.5 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 8 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang

EVERLIGHT ELECTRONICS CO.,LTD.

15-21SURC/S530-XX/TR8

4.Soldering Iron

seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.

5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used (as below figure). It should be confirmed beforehand
whether the characteristics of the LEDs will or will not be damaged by repairing.

Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3

EVERLIGHT ELECTRONICS CO., LTD. Tel: [phone]
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: [phone]
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.1 Page: 9 of 9
Device No: DSE-151-065 Prepared date: 07-01-2003 Prepared by: Jessica Chang