EVERLIGHT EVL 11-21SURC/S2 Datasheet

Technical Data Sheet
1206 Package Chip LED with Inner lens

11-21SURC/S530-A3/TR8

Features

․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS complaint version.

Descriptions

․The 11-21 SMD LED is much smaller than lead

frame type components, thus enable smaller board
size, higher packing density, reduced storage space
and finally smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.
․General use.

Device Selection Guide

Part No.

11-21SURC/S530-A3/TR8 AlGaInP Brilliant Red Water Clear

Chip

Emitted Color Resin Color

Material

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 1 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

Package Outline Dimensions

11-21SURC/S530-A3/TR8

-

+

Notes: The tolerances unless mentioned are ±0.1, unit=mm.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 2 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

11-21SURC/S530-A3/TR8

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit
Reverse Voltage VR 5 V
Forward Current IF 25 mA

Peak Forward Current

IFP 60 mA

(Duty 1/10 @1KHz)

Power Dissipation Pd 60 mW

Electrostatic Discharge(HBM) ESD 2000 V

Operating Temperature Topr -40 ~ +85

Storage Temperature Tstg -40 ~ +90

Reflow Soldering : 260 ℃ for 10 sec.

Soldering Temperature Tsol

Hand Soldering : 350 ℃ for 3 sec.

Electro-Optical Characteristics (Ta=25℃)

℃
℃

Parameter Symbol Min. Typ. Max. Unit Condition

Luminous Intensity Iv 90.0 ----- 180 mcd

Viewing Angle 2θ

Peak Wavelength λp ----- 632 ----- nm

Dominant Wavelength

Spectrum Radiation

Bandwidth

Forward Voltage VF

Reverse Current IR ----- ----- 10 μA

----- 60 ----- deg

1/2

λ

d

△λ

619.5 ----- 628.5

----- 20 -----

1.7 2.0 2.4

nm

nm

V

Notes:

1.Tolerance of Luminous Intensity: ±11%

2.Tolerance of Dominant Wavelength ±1nm

I

=20mA

F

V

=5V

R

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 3 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

Bin Range Of Luminous Intensity

Bin Min Max Unit Condition

Q2 90.0 112
R1 112 140
R2 140 180

Bin Range Of Dom. Wavelength

Bin Min Max Unit Condition

-----

619.5 628.5

Notes:

1.Tolerance of Luminous Intensity: ±11%

2.Tolerance of Dominant Wavelength ±1nm

11-21SURC/S530-A3/TR8

mcd IF =20mA

nm IF=20mA

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 4 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

Typical Electro-Optical Characteristics Curves

11-21SURC/S530-A3/TR8

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 5 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

Label explanation

CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank

Reel Dimensions

11-21SURC/S530-A3/TR8

Note: The tolerances unless mentioned are ±0.1, Unit = mm.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 6 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

11-21SURC/S530-A3/TR8

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: The tolerances unless mentioned are ±0.1, Unit = mm.

Moisture Resistant Packaging

Label

Aluminum moisture-proof bag

Desiccant Label

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 7 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

11-21SURC/S530-A3/TR8

Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.

Confidence level : 90 %
LTPD : 10 %

No. Items Test Condition

Temp. : 260℃±5℃

1 Reflow Soldering

Min. 5sec.

H : +100℃ 15min

2 Temperature Cycle

∫ 5 min

L : -40℃ 15min

H : +100℃ 5min

3 Thermal Shock

∫ 10 sec

L : -10℃ 5min

4

High Temperature

Temp. : 100℃

Storage

Test

Hours/Cycles

6 Min.

300 Cycles

300 Cycles

1000 Hrs.

Sample

Ac/Re

Size

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

5

Low Temperature

Temp. : -40℃

Storage

6 DC Operating Life IF = 20 mA

7

High Temperature /

85℃/ 85%RH

High Humidity

1000 Hrs.

1000 Hrs.
1000 Hrs.

22 PCS. 0/1

22 PCS. 0/1

22 PCS. 0/1

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 8 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

11-21SURC/S530-A3/TR8

Precautions For Use

1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.

If unused LEDs remain, it should be stored in moisture proof packages.

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 9 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua

11-21SURC/S530-A3/TR8

4. Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.

EVERLIGHT ELECTRONICS CO., LTD. Tel: [phone]
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: [phone]
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com

Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 2 Page: 10 of 10
Device No:SZDSE-111-007 Prepared date: 25-Oct-2007 Prepared by: Zhouhua