![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg1.png)
XTRON
Quick Start Guide
Copyright © EverFocus Electronics Corp,
Release Date: September, 2016
![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg2.png)
Table of Contents
Setting up the XTRON Server ........................................................ Error! Bookmark not defined.
Setting up the Static IP Address for the Network Cards ................. Error! Bookmark not defined.
How to Launch XTRON Software on the Server ........................................................................ 4
How to Connect to XTRON Server via Client PC ........................................................................5
The Correct Steps Required to set up XTRON ........................................................................... 5
Adding Door Controllers .......................................................................................................... 6
Setting up Door Preference .....................................................................................................8
Setting up Keypad/Reader ...................................................................................................... 9
Creating a Door Schedule ............................................................Error! Bookmark not defined.0
Creating an Access Group ............................................................Error! Bookmark not defined.2
Creating a Cardholder ........................................................................................................... 14
Syncing XTRON to the Door Controllers ................................................................................. 16
![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg3.png)
1
SETTING UP THE XTRON SERVER
The XTRON Server comes with two network cards that must be set up with a static IP address so
that the Door Controller Network can be separated from the Main Network. The Door
Controller will use LAN 2 to create a dedicated network for the door controllers while LAN1
will be used to connect the XTRON to the main network to allow remote login of client PC’s.
Please note that XTRON is a server and once the initial network is setup, a client PC should be
used to remotely log into the XTRON Server.
LAN 1 LAN 2
SETTING UP THE STATIC IP ADDRESS FOR THE NETWORK CARDS
Press the Windows Start button and go to the Control panel. Under “Network and Internet”,
choose “View Network Status and Tasks”. “Ethernet” is LAN port number 1 and “Ethernet 2” is
LAN port number 2. Choose “Ethernet” (figure 1.1a) to set up the main network so that client
PC’s can remote in. Click on “Properties” (figure1.1b), highlight “Internet Protocol Version 4”,
then click “Properties (figure 1.1c). Check “Use the Following IP Address” and enter the correct
![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg4.png)
2
IP address, Subnet mask and Gateway (figure 1.1d). This is the IP address that your client PC
will be using to log in to XTRON.
Figure 1.1a
Figure 1.1b
![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg5.png)
3
Figure 1.1c Figure 1.1d
To set up the Door Controller Network, go back to the “View Network Status and Task”
menu and choose “Ethernet 2” (figure 1.1a). Click “Properties” (figure 1.1b), highlight “Internet
Protocol Version 4” (figure 1.1c), then click on “Properties” and check “Use the Following IP
Address” (figure 1.1d). Enter the correct IP address that XTRON Server will be using in the
Door Network and click on “OK”.
![](/html/3f/3fd1/3fd10b0b9fe74b444e8a41044b95c91037a223716555a07f6812d229aad5b8bb/bg6.png)
4
HOW TO LAUNCH XTRON SOFTWARE ON THE SERVER
On the XTRON Server’s Desktop, locate the “xampp” icon and double click. This will
bring up a webpage to the XTRON Login page. Under email, type in admin@admin.com, and
the password will be admin. This is the default credential and can be changed.