EverFocus EZ-PLATECAM-002 User Manual

EZ-PLATECAM-002

High Contrast
License Plate Capture Camera

INSTALLATION & OPERATION MANUAL

Before attempting to connect or operate, please read and follow these instructions.

Contents

1. CAUTIONS

2. FEATURES

3. ITEMS PROVIDED IN THE BOX

4. COMPONENT AND CONTROL
NAMES AND FUNCTIONS

5. INSTALLATION

6. OSD MENU FUNCTIONS

7. INSTALLATION GUIDELINES

8. SPECIFICATIONS

9. DIMENSIONS

2

1. Cautions

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Note -

This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

WARNING -

This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Caution -

Any changes or modifications in construction of this device which are
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

1. If DC power is used a regulated DC12V 1A power supply is recommended for use
with this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.

If an unregulated power supply is used, product warranty will be void.

2. It is recommended that the camera is used with a monitor or other equipment that
has a CCTV quality 75 video impedance level.

3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to the manufacturer.

4. Never face the camera towards the sun, any bright, or refl ective light that may
cause smear on the picture or cause possible damage to the CCD.

5. Do not remove the serial number sticker.

3

1. Cautions

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes. Contact the
company where you purchased this product or your local government o ce for details
on how to properly dispose or recycle the product to be environmentally safe.

Business users should contact their supplier and check the terms and conditions of
the purchase contract.
Household users should contact the retailer for proper disposal procedures.

4

2. Features

• 1/3" Sony Super-HAD CCD

Ⅱ

• OSD Menu system customizes performance to match application

• High Resolution 600TV Lines

• Special filter and IR LEDs provide maximum readability
despite headlight glare

• Plate capture up to 35mph (56Km/H)

• 9.0 ~ 22.0mm Varifocal lens captures license plate
from 8ft ~ 33ft (2.5M ~ 10M)

• IP66 rated weather resistant

• Cable concealed through bracket

• DC12V / AC24V Dual power with auto-polarity

3. Items Provided In The Box

CAMERA

SUNSHIELD

VIDEO OUTPUT
TEST CABLE

L-WRENCH /
SCREW & Plastic anchor - 3ea /
SUNSHIELD FIXING BOLT

OPERATION MANUAL

5

4.

Component and Control Names and Functions

①

④

Sunshield Lock Bolt

①

Sunshield

②

Mounting Bracket

③

IR LED : 20ea

④

Camera Body

⑤

Body Lock Ring

⑥

External Zoom and Focus adjustments

⑦

②

⑦

①

⑤

⑧

⑥

③

⑦

Cover To Access Menu Controls & Test Video Output

⑧

Pressing the “SETUP” button prompts the main setup menu.
“PUSH” button : To access the main setup menu
“U” Direction : Menu item UP selection
“D” Direction : Menu item DOWN selection
“L” Direction : To change data or decrease value
“R” Direction : To change data or increase value

6

TEST
VIDEO
OUTPUT