EverFocus ESM316T002R User Manual
GIGABIT MANAGED
ETHERNET SWITCH
16 P
PLUS TWO SFP PORTS
oE+ PORTS
USER MANUAL
Part # ES M316T 0 0 2 R
ESM316T002R
#"
"
Content
CHAPTER 1 The Introduction ................................................................................ 5
Web Browser........................................................................................................ 5
Logging In............................................................................................................. 6
CHAPTER 2 System ............................................................................................... 8
System Information................................................................................................... 8
IP Address Setting ................................................................................................ 8
IPv6 Address Setting ............................................................................................ 9
User Account...................................................................................................... 10
Port Setting......................................................................................................... 10
CHAPTER 3 Configuration...................................................................................... 12
Trunk Group Setting ........................................................................................... 12
Trunk Distribution Algorithm Setting ................................................................... 13
LACP Setting ...................................................................................................... 15
Static VLAN Table Setting .................................................................................. 16
VLAN Port Setting .............................................................................................. 17
VLAN-Stacking Table Setting ............................................................................. 18
Vlan Stacking Setting ......................................................................................... 19
IGMP Multicast Group Information ..................................................................... 21
IGMP Snooping .................................................................................................. 22
IGMP Global Setting........................................................................................... 23
IGMP VLAN Setting............................................................................................ 24
Spanning Tree.................................................................................................... 25
Spanning Tree Port Setting ................................................................................ 27
Quality of Service (QoS)..................................................................................... 29
Port-based Priority Setting.................................................................................. 29
DSCP-based Priority Setting .............................................................................. 30
Priority to Queue Mapping Setting...................................................................... 31
$"
"
Packet Scheduling Setting.................................................................................. 32
LLDP Configurations .......................................................................................... 33
LLDP Neighbors ................................................................................................. 34
SNMP Setting..................................................................................................... 35
Trap Receivers Setting....................................................................................... 36
Port Mirroring Setting.......................................................................................... 37
Port Security Setting........................................................................................... 38
Bandwidth Control Setting .................................................................................. 40
Jumbo Frame Setting ......................................................................................... 42
Management Access Filter ................................................................................. 43
CHAPTER 4 Security............................................................................................... 45
MAC Address Information .................................................................................. 45
Static MAC Setting ............................................................................................. 46
MAC Filtering Setting.......................................................................................... 47
802.1x Setting..................................................................................................... 48
802.1x Port Setting............................................................................................. 49
IP Filter Configurations ....................................................................................... 50
Storm Control settings ........................................................................................ 52
Port Isolation....................................................................................................... 53
Defence Engine.................................................................................................. 54
CHAPTER 5 Monitoring........................................................................................ 55
Port Statistics Information................................................................................... 55
CHAPTER 6 Tools.................................................................................................... 56
Http Upgrade ...................................................................................................... 56
Reset Factory Defaults ....................................................................................... 57
Reboot ................................................................................................................ 58
%"
"
ABOUT THIS GUIDE
This guide provides information about how to operate and use the management functions of the Web Management Switch.
The switch features multiple functions as shown below:
Features Overview
Supports real-time status (link, speed, duplex) of each port
Supports port setting for enable or disable operation (the 1st port can’t be disabled)
Supports port setting for N-Way or force mode operation
Supports Broadcast Storm Protection
Supports Port-bases VLAN
Supports priority queues for QoS
Revision History
Several documents prepared beforehand are consulted, this manual is released as the first
edition. Date as August 2nd, 2011.
&"
"
CHAPTER 1 The Introduction
Web Browser
You can log into the Web Management Switch through a Web browser and manage and maintain the switch
intuitively by interacting with the built-in Web server. The home page is displayed as shown below. It displays
the Main Menu on the left side of the screen and an image of the front panel on the right side. The Main Menu is
used to navigate to other menus, and display configuration parameters and statistics.
Figure 1: Home Page
'"
"
Logging In
Please follow the steps to configure this Web Smart switch. The configure procedure is as follows:
Step 1: Use Ethernet Category 5 cable to connect this switch to your PC.
Step 2: Check that your PC has an IP address on the same subnet as the switch. For example, the PC and the
switch are on the same subnet if they both have addresses that start 192.168.1.x. The subnet mask is
255.255.255.0.
Step 3: Open the browser (like Microsoft Internet Explorer) and go to http:// 192.168.1.1, which is the switch
address, for example. If your PC is properly configured, you will see the login page like below:
Figure 2: Login Popping Up Window
NOTE: If you do not see the login page, check step 1 & 2.
Step 4: Please key in both the default user name “admin” and the password “admin” to pass the authentication.
After the authentication procedure, the switch can be used now, as the web home page appears as follows:
("
"
Figure 3: Web-Based Management Interface
)"
"
CHAPTER 2 System
System Information
To lookup System Information in the Web browser, click System, then Information.
Web Smart switch interface
Figure 4: System Information
IP Address Setting
To set up static IP address of the switch.
Web Smart switch interface
1. Click System, then IP Setting.
2. Set the Mode to “Static IP”.
3. Specify the IP address, subnet mask, and gateway address.
4. Click Apply.
Figure 5: IP Setting
*"
"
IPv6 Address Setting
IPv6 is an Internet Layer protocol for packet-switched internetworking and provides end-to-end datagram
transmission across multiple IP networks. IPv6 includes two distinct address types; link-local unicast and global
unicast.
Web Smart switch interface
Figure 6: IPv6 Address Setting
Hint§
The following parameters are displayed on the IPv6 Address Setting page:
■ Auto Configuration—Enable stateless auto configuration of IPv6 addresses on the interface and enables IPv6
functionality on the interface.
■ IPv6 Address—Manually sets up a global unicast address by specifying the full address and network prefix
length (in the Prefix field). (Default: null)
■ Prefix Length—Define the prefix length as a decimal value indicating how many contiguous bits (starting at
the left) of the address comprise the prefix; that is, the network portion of the address. (Default: 0)
■ Router—Set up the IPv6 address of the default next hop router. An IPv6 default gateway must be defined if the
management station is located in a different IPv6 segment. An IPv6 default gateway can only be successfully set
when a network interface that directly connects to the gateway has been configured on the switch.
!+"
"
User Account
To set up the System Password in the Web browser:
Web Smart switch interface
1. Click System, then User Account.
2. Enter the new user name.
3. Enter the new password.
4. Enter the new password again to confirm your input.
5. Click Save.
Figure 7: User Account Setting
Port Setting
To specify options for enabling auto-negotiation or manually setting the speed and duplex mode, or enabling flow
control.
To set up port configuration in the Web browser:
1. Click System, Port Setting.
2. Select one or more ports to configure.
3. Make any required changes to the connection settings.
4. Click Apply.
!!"
"
Figure 8: Port Setting
Hint§
The following parameters are displayed on the Port Setting configuration:
■ Port—Set up one or more ports. Hold down the CTRL key and click port numbers to select multiple ports.
Hold down the SHIFT key to select a range of ports.
■ State—Set the link state of port interfaces. (Default: Enabled)
■ Speed/Duplex—Configure the port speed and duplex mode using auto-negotiation or manual selection.
(Default: Auto-negotiation enabled)
■ Auto - Enable auto-negotiation. When using auto-negotiation, the optimal settings will be negotiated between
the link partners based on their advertised capabilities. Auto must be enabled for all 1 Gbps connections.
■ 100M/Full - Support 100 Mbps full-duplex operation
■ 100M/Half - Support 100 Mbps half-duplex operation
■ 10M/Full - Support 10 Mbps full-duplex operation
■ 10M/Half - Support 10 Mbps half-duplex operation
■ Flow Control—Display the following:
■ Config – The configured flow control mode of the port.
■ Actual – Indicate the link status of the port. When a link is up, indicates the operating flow control mode.
!#"
"
CHAPTER 3 Configuration
Trunk Group Setting
To configure a trunk group.
Web Smart switch interface
1. Click Configuration, Link Aggregation, Trunk Group Setting.
2. Select the trunk group ID to be created or modified.
3. Select the trunk type; Static or LACP.
4. Assign up to four port members to the trunk.
5. Click Add/Modify.
Figure 9: Trunk Group Setting
!$"
"
Trunk Distribution Algorithm Setting
To configure a trunk’s load-balancing settings.
Web Smart switch interface
1. Click Configuration, Link Aggregation, Trunk Setting.
2. Select the trunk group ID to be configured or modified.
3. Select the trunk Distribution Algorithm Parameters as required.
4. Click Apply.
Figure 10: Trunk Distribution Algorithm Setting
Hint§
The switch provides five load-balancing methods to distribute a balanced load across all links in a trunk. The
following parameters are displayed on the Trunk Distribution Algorithm Setting:
■ Distribution Algorithm Parameters—To ensure the switch traffic load is distributed evenly across all links in
a trunk, the hash methods used in the load-balance calculation can be selected to provide the best result for trunk
connections. The following options are supported:
■ Source Port - All traffic with the same source and destination TCP/UDP port number is output on the same
link in a trunk. Avoid using his mode as a lone option. It may overload a single port member of the trunk for
application traffic of a specific type, such as web browsing. However, it can be used effectively in
combination with the IP Address option.
■ Source MAC - All traffic with the same source MAC address is output on the same link in a trunk. This
mode works best for switch-to-switch trunk links where traffic through the switch is received from many
different hosts.
!%"
"
■ Destination MAC - All traffic with the same destination MAC address is output on the same link in a trunk.
This mode works best for switch-to-switch trunk links where traffic through the switch is destined for many
different hosts. Do not use this mode for switch-to-router trunk links where the destination MAC address is the
same for all traffic.
■ Source IP - All traffic with the same source and destination IP address is output on the same link in a trunk.
This mode works best for switch-to-router trunk links where traffic through the switch is destined for many
different hosts. Do not use this mode for switch-to-server trunk links where the destination IP address is the
same for all traffic.
■ Destination IP - All traffic with the same source and destination IP address is output on the same link in a
trunk. This mode works best for switch-to-router trunk links where traffic through the switch is destined for
many different hosts. Do not use this mode for switch-to-server trunk links where the destination IP address is
the same for all traffic.
!&"
"
LACP Setting
The LACP (link aggregation control protocol) dynamically aggregates ports and removes aggregations. LACP
interacts with its peer by sending LACPDUs (link aggregation control protocol data units).
Web Smart switch interface
To arrange LACP settings,
1. Click Configuration, Link Aggregation, LACP Setting.
2. Enable LACP on the switch.
3. Specify the LACP System Priority to identify LAGs (link aggregation group) on the switch.
4. Click Apply.
Figure 11: LACP Setting
Hint§
The following parameters are shown on the LACP Setting:
■ LACP Status – Specify whether LACP is enabled on this switch. LACP will aggregate two or more ports if
they belong to the same group. LACP can form up to 8 trunks per switch.
■ System Priority – LACP system priority is used to identify LAGs membership of this switch to other switches
during LAG negotiations. (Range: 0-65535, Default: 32768)
!'"
"
Static VLAN Table Setting
The VLAN (virtual local area network) technology is developed for switches to control broadcast operations in
LANs. By creating VLANs in a physical LAN, you can divide the LAN into multiple logical LANs, each of
which has a broadcast domain of its own. Hosts in the same VLAN communicate with each other as if they are in
a LAN. However, hosts in different VLANs cannot communicate with each other directly. In this way, broadcast
packets are confined within a VLAN.
Web Smart switch interface
To manage VLAN groups,
1. Click Configuration, VLAN, Static VLAN.
2. Select a VLAN ID number.
3. Define a name to identify the VLAN.
4. Mark the ports to be assigned to the new VLAN as tagged or untagged members.
5. Click Add/Modify.
Figure 12: Static VLAN Table Setting
Hint§
The following parameters are shown on the Static VLAN Table Setting:
■ Port – Select VLAN membership for each interface by marking the appropriate radio button for a port or trunk
as Untagged, Tagged, or Not Member
■ VLAN ID – VLAN Identifier. (Range: 1-4094)
!("
"
■ VLAN Name – Name of the VLAN (1-100 characters)
VLAN Port Setting
Arranging VLAN attributes for specific interfaces, including the default Port VLAN identifier (PVID).
Web Smart switch interface
To specify attributes for VLAN port members,
1. Click Configuration, VLAN, VLAN Setting.
2. Select one or more ports or trunks to configure.
3. Configure the required PVID setting.
4. Click Apply.
Figure 13: VLAN Port Setting
Hint§
The following parameters are shown on the Static VLAN Table Setting:
■ Port –Select one or more ports to configure. Hold down the CTRL key and click port numbers to select
multiple ports. Hold down the SHIFT key to select a range of ports.
■ PVID - The VLAN ID assigned to untagged frames received on the interface. (Range: 1-4095, Default: 1) Ports
must be a member of the same VLAN as the Port VLAN ID.
!)"
"
VLAN-Stacking Table Setting
Set the stacking VLAN membership for selected interfaces to be part of the Service Provider VLAN (S-VLAN),
that is uplink ports for a 802.1Q Tunnel. This stacking VLAN is used to segregate and preserve customer VLAN
IDs for traffic crossing the service provider network. The switch supports up to 64 S-VLAN IDs.
Web Smart switch interface
To manage stacking VLAN port members,
1. Click Configuration, VLAN Stacking, S-VLAN Table.
2. Specify the S-VLAN ID number.
3. Mark the ports to be included as stacking VLAN port members for specified S-VLAN.
4. Click Add.
Figure 14: VLAN-Stacking Table Setting
Hint§
The following parameters are shown on the VLAN-Stacking Table Setting:
■ S-VLAN ID - The VLAN identifier of a stacking VLAN. (Range: 1-4094)
■ Member Ports - Switch ports that are members of the stacking VLAN. That is, ports that will double tag
ingress and egress packets.
Loading...