EverFocus EQ700 Ultra 720+ Series User Manual

EQ700 Ultra 720+ Series

True Day/Night Box Camera

User’s Manual

** Lens not included.

Copyright © EverFocus Electronics Corp,

Release Date: January, 2014

i

Precautions

Please read this manual first to ensure correct installation and operation. This manual should be
retained for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV / radio transmitters, magnets, electric motors, transformers
and audio speakers, because the electromagnetic fields generated by these devices may
distort the video image or otherwise interfere with camera functions.

2. Never disassemble the camera beyond the recommendations in this manual, nor apply
materials to it other than those recommended herein.

Improper disassembly or introduction of corrosive materials may result in equipment failure
or other damage.

3. Try to avoid pointing the camera toward the sun.

In some circumstances, direct sunlight may cause permanent damage to the sensor and / or
internal circuits. It may also create unbalanced illumination that may be beyond the camera’s
ability to compensate.

4. Keep the power cable away from water and other liquids. Never touch the power cable
with wet hands.

Touching a wet power cable with your hands or touching the power cable with wet hands
may result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents.

Oil, gas or solvents may cause equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning

For cameras with interchangeable lenses, do not touch the surface of the sensor directly
with your hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the
sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body.
Do not use complex solvents, or corrosive or abrasive agents to clean any part of the camera.

7. Do not operate the camera beyond the specified temperature, humidity and power source
levels. This camera is suitable for indoor operation only.

Use the camera at temperatures within -10°C ~ 50°C (14°F ~ 122°F ) and humidity between
20 ~ 80%; this device is not rated as submersible. The input power source should be 12VDC
or 24VAC. The use of a properly fused or “Class 2 Limited Power Source” power supply is

highly recommended.

8. Mounting

Select a solid mounting surface that will support the weight of the camera and any
additional loading from wind, snow, ice or other factors. Securely attach the camera to the
mounting surface using screws and anchors that will properly support the camera. If
necessary, (e.g. when mounting the camera to a drop ceiling, or unsupported ceiling) use a
safety wire to provide additional support for the camera.

ii

Safety Notice

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

This Product is RoHS compliant.

ATTENTION! This is a class A product which may cause radio interference in a domestic

environment; in this case, the user may be urged to take adequate measures.
WEEE

Your EverFocus product is designed and manufactured with high quality materials and

components which can be recycled and reused. This symbol means that electrical and

electronic equipment, at their end-of-life, should be disposed of separately from your

household waste. Please, dispose of this equipment at your local community waste

collection/recycling centre. In the European Union there are separate collection systems for

used electrical and electronic product.

Please, help us to conserve the environment we live in!

iii

Contents

1. INTRODUCTION ........................................................................................ 1

1.1 PACKING LIST .............................................................................................................. 1

1.2 FEATURES .................................................................................................................. 1

2. OVERVIEW ............................................................................................... 2

3. INSTALLATION .......................................................................................... 2

3.1 LENS INSTALLATION AND ADJUSTMENT ................................................................................ 2

3.2 TOP / BOTTOM-MOUNT ................................................................................................. 3

4. BASIC CONNECTION .................................................................................. 3

5. OSD MENU STRUCTURE ............................................................................ 4

6. SPECIFICATIONS ........................................................................................ 6