EverFocus EPTZ850 User Manual

User Manual

Intelligent High Speed Dome

Camera

Note:

Read this manual carefully before installation and operation. Keep it handy

for later reference.

2/ 24

CONTENTS

1. Product Introduction

1.1 Features…………………………………………………….…………….3

1.2 Function………………………………………………………………….4

2. Installation Instruction

2.1 Wiring Diagram………………………………………………………….7

3. Basic Operation……………………………………………………………….8

4. Menu Settings

4.1 Main Menu……………………………………………………………….11

4.2 System Information…………………...…………………………………12

4.3 Address setting……………………………………………………...……12

4.4 Pan Tilt Setup……………………………………………………...…......13

4.5 Trajectory Scan…………………………………………………………..16

4.6 Setting Camera menu……………………………………………………17

4.7 Cruise setting…………………………………………………………….18

4.8 Display Setup…………………………………………………………….19

5. Trouble Shooting

5.1 List of malfunction removal……………………………………………20

5.2 Attention…………………………………………………………………21

Specifications………………………………………………….23

3/ 24

1. Product Introduction

1.1 Features

Strong Intelligence Function:

 Compatible with PELCO-D, PELCO-P and EverFocus Protocol.

 Recognize 2400, 4800, 9600 Baud Rate.

 Automatic recognition for RS 485 control protocol.

 With 4CH trajectory scan and 4CH preset cruise

Strong Horizontal and Vertical Rotation Function:

 Max. 180 degree/Sec. High speed pan tilt rotation.

 Based vector drive technology, guarantee the P/T function can be executed at

minimum route and make the target distance closer. Therefore, it is more true

and natural for us to view the video.

 Adopt the advance motor ultrafine classification technology,

Minimum rotation speed of pan tilt can reach the 0.05 degree/sec., make the

video image more accurate and stable under high magnification.

Presets, Trajectory Scan, Zones Scan, Continuous Scan

 Maximum 220 presets and every preset include magnification of lens and angle

position.

 It may record and display 4 trajectory scan route

4/ 24

 Set up the left and right border of specified zones, pan tilt zoom dome can rotate

at specified speed.

 Call the specified special preset can be 360°durative scan.

OSD English Menu

 Built-in OSD English screen menu, it can modify the info and the parameter

PTZ Dome via menu.

 Horizontal/Vertical angle magnification of lens and presets can be displayed on

screen.

PTZ Control

 Adopt RS485 protocol
 360 degrees horizontal durative rotation, vertical 90 °rotation. Turn over 180°,

continuous monitor,

 Horizontal speed 0.05-360 degrees, vertical speed 0.05 -90 degrees, it can adjust

automatically as per lens zoom times.

1.2 Function

1.) Setup of address code

Any operation commands have the target address code, baud rate, control protocol

for related high speed PTZ dome, single camera only can be committed to

commands in conformity with relevant address code, baud rate and control

protocol. Our high speed PTZ Dome camera can recognize camera address, baud

rate and control protocol automatically.

5/ 24

2.) Focal length/rotation speed auto. Configure technology.

When you adjust manually, if the focal length is too long and when you touch the

PTZ keyboard joystick lightly under the high speed pan tilt rotation, it may let the

video image move promptly and can lead to data loss. Based on this, our High

Speed PTZ Dome can adjust the horizontal and vertical speed according to the

focal length, it makes the manual tracking target be more convenient.

3.) Reserve and call preset

Preset function is that store parameter such as pan tilt horizontal angle; slope

angle and camera lens focal length into memory. If necessary, you can call this

parameter and adjust pan tilt and camera lens to this position. User can store and

call presets via using PTZ control keyboard and IR controller. This PTZ Dome

has 220 presets.

4.) Lens control

（1）Focal length control

User can adjust the range of focal length via using PTZ control keyboard or

matrix host machine, and then will get the complete video.

（2）Focus control

System starts to focus and zoom by default; the camera lens will focus at the

center around the target view and will keep the image clear. It also can focus

manually and reach the expected image effects. When you are in control of

manual focus, and if you want to reset to autofocus, you just operate from the

joystick of PTZ keyboard. In addition, you may set a control command or call a

6/ 24

preset to reset auto focus.

5.) Auto. Cruise

It can add some presets into auto. cruise section in turn via preset cruise preset

sites. You just set command of 99 preset or use the idle motion to make the PTZ

dome move continuously within certain space of time as per the turn of reserved

presets.

6.) Trajectory scanning

Trajectory scanning is that store operation trajectory via menu, it can call the

reserved scan route via No. 84,No. 85,No.86, No.87 command or idle motion.

7.) Continuous scanning

You just set command for NO. 98 preset or call it by idle motion, and then you

can scan circularly in horizontal position at certain speed.

8.) Intermittent scanning

You just set command for NO. 96 preset or call it by idle motion, and then you

can scan circularly at space of time in horizontal position at certain speed.

7/ 24

2. Installation Instruction

2.1 Wiring Diagram

Power supply: DC 12V 3A interface
Control cable: RS485 control
Video cable: BNC interface

Power supply connection

Attention：Please check the voltage rating and electric current, it is as below,

Voltage Rating

Range of Voltage Rating

Electric Current

DC 12V

±5%

3A

 Connection of control cable

PTZ control: connect RS-485 cable to PTZ control keyboard or DVR. If you control

more than one camera, RS-485 cable needs to be settled parallel position.

Note：①The RS-485 cable can be connected optionally

②Protocol and baud rate of PTZ control keyboard or DVR can be settled

optionally

③Some cameras in CCTV system should set different PTZ dome address

 Video

Use BNC plug to connect video signal cable.

8/ 24

3. Basic Operation

As the concrete operation methods are not exactly the same for different platform

systems, you are suggested to operate according to the user manual. Under some

circumstances, when it may needs particular operation; please contact the supplier for

necessary instructions. Here the introduction is only about the operation methods on

PTZ dome when you use the PTZ keyboard.

1.) Self-check

After you Turn ON the power for PTZ dome, the camera will rotate horizontally and

vertically, and then zoom in and zoom out, and finally stop when it reaches the zoom

limits. Through self-checking, you can be made sure of the normal operation for the

PTZ camera.

How to control the camera when it rotates in different directions?

When you locate a camera, you can control it via the joystick on the keyboard. When

you move the joystick to the right, the camera will move to the right. In the same way,

it will move to the left when you move the joystick to the left. When you move the

joystick in vertical direction, the camera will move accordingly in vertical direction.

Similarly, the camera will move simultaneously in horizontal and vertical direction

when you shake the joystick in diagonal direction.

2.) Presets setup

Please set the presets as below,

(1) Operate joystick of keyboard, zoom button, focus button and iris button to adjust

video image of camera

(2)Press the Arabic number key (please input the number of specified preset)

+PRESET, to save parameter of preset view.