EverFocus EPD200A User Manual

EVERFOCUS

Indoor Pendent Dome Camera

Operation Instructions

Model No. EPD200

Please read this manual first for correct installation and operation. This manual should be retained

for future reference. The information in this manual was current when published. The

manufacturer reserves the right to revise and improve its products. All specifications are therefore

subject to change without notice.

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,

audio speakers since the magnetic fields generate from above devices will distort the video

images.

2. Never disassemble the camera nor put impurities in it.

Disassembly or impurities may result in trouble or fire.

3. Never face the camera toward the sun.

Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.

4. Keep the power cord away from water and liquid.

Touching the wet power cord may result in electric shock.

5. Never install the camera in areas exposed to water, oil or gas.

Water, oil or gas may result in failure, electric shock or fire.

6. Cleaning

Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from

the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the

camera lens.

7. Do not operate the camera beyond the specified temperature, humidity or
power source ratings.

Use the camera at temperatures within 0℃~ 50℃/32℉~122℉ and humidity between 20%~
80%. The input power source is 12VDC/24VAC.

PREFACE

EPD200 is compact, full functioned CCD Color Cameras for indoor pendent mount. The

dome camera is designed with advanced digital processing circuitry for high resolution 1/3"

CCD sensor, it has DIP switch for FL ON/OFF, BLC ON/OFF, AGC ON/OFF. The dome

camera uses a vari-focal auto iris lens for discreet surveillance or close-up viewing and it

features with iris level volume control for the best viewing quality.

FEATURES

z 1/3” SONY CCD pick up device for more than 380 TV lines of horizontal resolution
z The high sensitivity of 1.0 Lux/F=1.2 is achieved by using 1/3” SONY CCD
z The Electronic Shutter and AGC functions allow the camera to be used in environment

with varying light levels

z Built-in Vari-Focal lens(optional)
z With manual PAN mechanism up to 90 degree
z FL, BLC, AGC On/Off switchable
z Compact size
z System available for NTSC or PAL

CONTENT LIST

1. Camera Unit

2. Operation Instructions (this document)

3. Hex Wrench

4. Power Extension Cable

5. Video Cable for testing Video Connector

OPTIONAL ACCESSORY

• EN220 5.6-inch LCD Test Monitor

1

SPECIFICATION

N

N

Pickup Device 1/3" SONY Super HAD CCD
Video Format
Scanning System

Picture Elements 510 x 492 (NTSC); 500 x 582 (PAL)
Horizontal Resolution 380 TVL
Sensitivity 0.3 Lux /F=1.2
S/N Ratio Over 48dB(AGC Off)
Electronic Shutter 1/50(1/60)~1/100,000

Lens
Video Output BNC 1.0Vp-p 75ohm

Back Light Comp.. On/Off switch
Auto Gain Control On/Off switch
Flickerless On/Off switch
Auto White Balance Auto
Auto IRIS DC-Drive
Gamma Correction 0.45
Sync. Mode Internal Sync.
Power Source Two types:

Power Consumption 12VDC:3W max.

Video Output Connector

AC 24V Power Connector + Video

TSC or PAL
TSC: 525 TV lines, 60 fields/sec.

PAL: 625 TV lines, 50 fields/sec.

Vari-Focal or Fixed Lens

12VDC/24VAC
12VDC only

24VAC: 1.5W max
BNC output x 1

2.5mm Lock x 1

2.5mm x 2-pin(for DC jack)

2.0mm x 2-pin(for BNC)

DC 12V Power Connector + Video 1.25mm x 4-pin, (1BNC, DC jack)
Weight 0.3 kg ; 0.66 lbs
Dimension 110mm(W)x 125(H)/ 4.33”(W) x4.92”(H)

Pendent Tube Diameter: 26mm/1.06”

Operating Temperatur e 0~50 ; 32°F~122°F (20%~80% Humidity)
Certifications CE, FCC

2