EverFocus EHD525EX User Manual

EVERFOCUS

1/3” Sony ExView Day/Night

Rugged Dome Color Camera

Operation Instructions

Model No.

Please read this manual first for correct installation and opera tion. This manual should be retain ed
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.

EHD525EX

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.

2. Never disassemble the camera nor put impurities in it.

Disassembly or impurities may result in trouble or fire.

3. Never face the camera toward the sun.

Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.

4. Keep the power cord away from water and liquid.

Touching the wet power cord may result in electric shock.

5. Never install the camera in areas exposed to water, oil or gas.

Water, oil or gas may result in failure, electric shock or fire.

6. Cleaning

Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from
the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the
camera lens.

7. Do not operate the camera beyond the specified temperature, humidity or
power source ratings.

Use the camera at temperatures within -40℃ ~ 50℃ (-40℉ ~ 122℉) and humidity
between 20%~ 80%. The input power source is 12VDC/24VAC.

PREFACE

The most technically advanced EHD series are the newest vandal-resistant Color Rugged
Dome Camera from EverFocus Electronics. The Color Rugged Dome Camera can
withstand a blow from a 10-pound sledgehammer and has a built-in heater that allows for
operation in low temperatures. It is perfect for all high-profile crime-prone applications
such as building entrances, retail stores, and shopping malls. The extremely EHD series
are unquestionably one of the world's toughest cameras and is your best choice for
vandal resistance. EHD525EX is designed with True Day/Night function that allows
removable Auto IR Cut and an enhanced B/W sensitivity, while turning the image from
color to B/W.

FEATURES

z 560 TVL of horizontal resolution
z 1/3” Sony ExView CCD with low light sensitivity of 0.1 lux/F=1.2
z Revolutionary integrated 10-bit Digital Signal Processor (DSP) delivers excellent

picture quality and sharp color images

z Designed with polycarbonate shell to withstand the impact of a 10 lb sledgehammer
z Aluminum base with smoke color shell
z Day/Night with IR cut removable module
z Dual voltage: 12VDC or 24VAC

PACKAGE CONTENTS

Standard Accessories

z Camera Unit x 1
z Accessory Pack includes:

- Screws x 4

- Expanding Screws x 4

- Wrench x 1

1

z Conduit x 1
z Power & Video Cable x 1
z Desiccant Pack x 1
z Manual x 1

Optional Accessory

z Wall Mount Bracket (BA-EHD)

SPECIFICATIONS

Pickup Device 1/3'' SONY EXView CCD
Video Format NTSC or PAL

Scanning System

NTSC: 525 TV lines, 60 fields/sec

PAL: 625 TV lines, 50 fields/sec
Picture Elements 768 x 494(NTSC) ; 752 x 582(PAL)
Horizontal Resolution 560TVL
Sensitivity 0.1Lux/F=1.2
S/N Ratio Over 50dB(AGC off)

Electronic Shutter 1/50(1/60)~1/100,000

Vari-focal lens, Auto Iris

f=2.9~10mm, F=1.2
Lens Type

f=3.6~9mm

f=9~22mm, F=1.6

*Lens models and availability vary in different regions

Back Light Comp. ON/OFF Switch

Auto Gain Control ON/OFF Switch
Flickerless ON/OFF Switch
Auto White Balance Yes

Gamma Correction 0.45

2 video outputs
Video Output

BNC 1.0Vp-p, 75ohm

Additional testing video output 1.0Vp-p, 75ohm
Sync. Mode Line Lock/Internal Sync.
Weatherproof IP66
Vandal Resistant Yes
Heater Yes, built-in

2

Power Source 12VDC/24VAC

24VAC: 6VA max. (Heater OFF)

Power Consumption

Dimensions

Weight 1.7kg ; 3.7lbs
Operating Temperature -40°C~50°C ;- 40°F~122°F (20%~80% Humidity)
Certifications FCC/CE

24VAC: 20.5VA max. (Heater ON)

12VDC: 4W max. (Heater OFF)

12VDC: 11.5W max. (Heater ON)

130mm(W) x 98.8mm(H) x 130mm(D);

5.1"(W) x 3.9"(H) x 5.1"(D)

DIMENSIONS

INSTALLATION

1. Loosen the 4 fix screws on the housing cover by using the attached wrench (Figure 1).

Carefully uncap the housing cover as the direction shown below (Figure 2), please pay

attention not to damage the lens. To remove the housing cover, push the hinges to the

bottom of the bracket, the hinges can be easily removed from the bracket.

3

Figure 2

2. Remove the camera.

Figure 1

Vari-Focal Lens

Heater

Locking Screws

To remove the camera, first unplug the wire connection on the back of the camera. Then

loosen the 2 locking screws on the camera base, push the camera base to the right (toward

heater direction, as shown in Figure 3), remove the camera from the mounting base.

Reinstall the camera and the cable while the base mounting is completed.

Figure 3

3. Mounting the base.

Back conduit entry

Mounting Setscrew

Side conduit entry

Mounting Setscrew

Conduit plug setscrew

Mounting Setscrew

Mounting Setscrew

Figure 4

4