EverFocus EHD363 User Manual

EVERFOCUS

Dual Power High Resolution Vandal Proof

Weather Resistant 3-Axis IR Dome Camera

Operation Instructions

Model No.

Please read this manual first for correct installation and operation. This manual should be retained for
future reference. The information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject to change without
notice.

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic fields generated from these devices may distort the video image or otherwise interfere
with camera operation.

2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials

other than those recommended herein.

Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.

3. Try to avoid facing the camera toward the sun.

In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal circuits, as
well as creating unbalanced illumination beyond the capability of the camera to compensate.

4. Keep the power cord away from water and other liquids and never touch the power cord with wet

hands.

Touching a wet power cord with your hands or touching the power cord with wet hands may result in electric
shock.

5. Never install the camera in areas exposed to oil, gas or solvents.

Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning

For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use
lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft
cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive
agents for cleaning of any part of the camera.

EHD363

CAUTION

7. Do not operate the camera beyond the specified temperature, humidity or power source ratings. This

camera is suitable for indoor and outdoor operation.

Use the camera at temperatures within -10°C to +50°C (14°F to 122°F) and in an IP66 compliant environment;

this device is not rated as submersible. The input power source is 12VDC or AC24V. Be sure to connect the

proper voltage, as too high a voltage will likely cause the camera to fail, and such damage is not
covered by the warranty. The use of properly fused or Class 2 power limited type supplies is highly
recommended. Regulated supply is required for 12VDC operation.

8. Mounting

Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind,
snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors
which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to
provide additional support for the camera.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, D O NOT REMOVE

COVER (OR BACK), NO USE R S ERVICEABLE PARTS INSIDE.

REFE R SERVI CING TO QUALIF IED SE RVICE P ERSONN EL.

OVERVIEW

The EHD363 is an outdoor, vandal resistant 3-axis IR dome camera which utilizes a Sony 1/3” 960H

Exview HAD CCD Sensor and enhanced Effio-E DSP to provide high resolution 700TVL color video

for security surveillance applications. Advanced functions including Digital WDR/ATR (Adaptive Tone

Reproduction), 2D-NR (2D Noise Reduction) and Anti CR (Anti Color Rolling) insure optimum image

quality under low or unbalanced lighting conditions. Vandal Proof materials and an IP66 weather

resistant housing allow reliable operation in outdoor and indoor environments. True day/night operation

combined with 30m (~98ft.) range high efficiency IR LEDs makes the EHD363 suitable for a wide range

of day and night surveillance situations. Plus, dual voltage 12VDC/24VAC operation, 3-axis mechanical

design and built-in f=3.7~12mm varifocal auto iris lens bring flexibility to installation and field of view

adjustment.

FEATURES

 Sony 1/3” 960H EXview HAD II high resolution CCD sensor for 700TVL images
 Employs Sony Enhanced Effio-E Digital Signal Processor (DSP) chip-set for advanced image

processing.

 Built-in Auto Gain Control (AGC), Auto Tracing White Balance (ATW) enhance image quality

 Advanced DSP functions enhance image quality: Digital WDR/ATR (Adaptive Tone Reproduction),

2D-NR (2D Noise Reduction), Anti CR (Anti Color Rolling)

 Varifocal DC iris 3.7~12mm lens and 3-Axis design for flexible field of view adjustment

 Eleven high efficiency IR LEDs with 30m (~98ft.) range in for low/no light applications

 True day/night auto switching for best day time color and low light performance

 Vandal proof to withstand impact of a 10 pound sledgehammer.

1

 Weather resistant, IP66 rated

 Dual power: 12VDC/24VAC

PACKAGE CONTENTS

 Camera Unit x 1
 Mounting kit includes:

-Screws x 4

-Security wrench for housing screws x 1

-Expanding Anchors x 4

-Washers x 4

 Operation Instructions (this document) x 1
 Weatherproof bushing x 1
 Power cable x 1
 Video cable x 1
 Power adapter pigtail (for NTSC model only) x 1
 Mounting template x 1

SPECIFICATIONS

Pickup Device SONY 1/3” 960H EXview HAD II CCD High Resolution

Video Format NTSC

Picture Elements 976 x 494

Horizontal Resolution 700 TV line

Sensitivity 0.01Lux / F1.4; 0Lux / IR

S/N Ratio More than 54 dB

Electronic Shutter 1/60s~1/100,000s

Video Output BNC-F 1.0Vp-p 75Ω

Gamma Correction 0.45

Lens Type Vari-Focal 3.7~12mm / F1.4 DC Drive Auto Iris Lens

Day/Night True day/night with motorized IR cut filter

Gain Control Automatic

White Balance ATW (1800°K~10500°K) with Anti-CR Function

Digital WDR ATR On (Luminance and Contrast = High)

Noise Reduction 2-D DNR (C Level 4, Y Level 4)

Sync. Mode Internal Sync.

IR LED 11 Units High Efficiency IR LED

IR Wavelength 850nm

IR Distance 30m (~98ft.) nominal; depends on environment

Weather Resistant IP 66

Vandal Proof IK10

Power Source 12VDC or 24VAC

Power Consumption 283mA @12VDC, 8W @ 24VAC

2

Operating Temperature -10°C~50°C / 14°F~122°F

Dimensions (O.D. x H) 142mm x 115.5mm / 5.6” x 4.55”

Weight 979 g / 2.16 lbs

Certifications CE / FCC

DIMENSIONS

Dimensions

D

Bottom View

A. Lens

B. IR-LED

C. Side conduit entry

D. Back conduit entry

A

Front View

E

Bottom View

E. Mounting holes

F. BNC Connector

G. DC Connector

C

B

F
G

3

INSTALLATION INSTRUCTIONS

Drill the Holes

1. Locate the desired mounting location; position housing with camera pointed generally in the desired

direction and mark location.

2. Use template to fix hole locations. Drill 4 holes for mounting screws (or anchors and insert plastic

anchors into holes after drilling as required).

Mounting Steps

1. Use the security wrench provided to loosen the 4 screws holding the dome cover.

2. Remove the dome cover. (IF REAR WIRE MUST BE REMOVED/RELOCATED, SEE STEPS

4~8) Attach the camera body to the mounting surface with the mounting screws provided

3. Tighten the 4 mounting screws to secure the camera body to the mounting surface.

4. If you need to wire cable through side conduit hole, use a coin to remove the conduit plug; save the
plug as it will be used to close the rear conduit hole.

Back conduit
hole

Conduit plug

Side conduit hole

4

5. Disconnect the power and video wire from the camera board end of the wire (1x 4 pin white connector)

and the 2 power wires from the power board attached to the base plate (1 x 2 pin connector with blue

marking and 1 x 2 pin connector with white color). Gently pull the wires out from under the plate until

they are free. Using wrench or pliers, remove the weather tight bushing from the rear conduit hole. Using

the plug removed in step 3 above, close the rear conduit hole (additional caulk or other sealant

recommended).

6. Pass the camera end of the power/video cable through side conduit hole. Using wrench or pliers,

carefully tighten the weather tight bushing into the side conduit hole.

7. (Optional) Pass the power/video wires under the base plate and up through the center hole.

8. Position the power/video wires so that they don’t interfere with the camera module and carefully

attach the 4 pin white connector to the camera board, being sure to position the connector so it fits

properly onto the tiny pins within. Next, attach the blue 2 pin connector and the white 2 pin connector to

the matching color receptacles on the power board. NOTE: the 2 pin blue connector goes into the

receptacle marked in blue on the power board. Failure to properly attach these connectors may

permanently damage the camera.

General Connection and Setup

1. Connect the power cord to DC 12V or AC 24V power supply

2. Use 75 ohm type coaxial cable to connect the camera to a monitor or DVR.

5

3. Loosen the screws which lock the tilt mechanism. Rotate the pan and tilt mechanisms to point

the camera in the desired direction. Rotate the camera module on its axis if necessary to align the

image ‘upright’. Loosen the lens adjusting screws and adjust the lens to obtain the desired field of

view and focus.

Tilt lock

Lens adjustment

2 places

Focus adjustment

4. Lock the lens and tilt screws. Put the dome cover back and align the clear window in the dome

cover with the lens. Attach the dome cover to dome base with the 4 mounting screws.

NOTE: The cover only goes on in ONE direction. There is a key and slot; if not aligned, cover will not

close properly.

NOTE: If you move the camera module, it is necessary to loosen the dome and liner and reposition

the liner so the lens points out through the slot, and the rubber seal presses onto the clear part of the

dome and not the liner. Loosen 4 Philips screws, reposition liner, then TIGHTEN four cover attachement

screws (else seal and vandal resistance is compromised).

6

Your EverFocus product is designed

Ihr EverFocus Produkt wurde entwickelt

EverFocus Electronics Corp.

EverFocus Taiwan:

12F, No.79, Sec. 1, Shin-Tai Wu Road,

Hsi-Chih, Taipei, Taiwan

TEL: [phone]

FAX: [phone]

www.everfocus.com.tw

[e-mail]

EverFocus China - Beijing:

Room 609, Technology Trade Building,

Shangdi Information Industry Base,

Haidian District, Beijing 100085, China

TEL: [phone]~39

FAX: [phone]

www.everfocus.com.cn

[e-mail]

EverFocus USA - California:

1801 Highland Avenue, Unit A, Duarte, CA 91010,

USA

TEL: [phone]

FAX: [phone]

www.everfocus.com

[e-mail]

EverFocus Europe - Germany:

Albert-Einstein-Strasse 1, D-46446

Emmerich, Germany

TEL: [phone]

FAX: [phone]

www.everfocus.de

[e-mail]

EverFocus China - Shenzhen:

4F, No. 2, D4 Building, Wan Yelong

Industrial Park, Tangtou Road, Shiyan,

Baoan, Shenzhen, Guangdong 518101, China

TEL: [phone]

FAX: [phone]

www.everfocus.com.cn

[e-mail]

EverFocus USA - New York:

415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA

TEL: [phone]

FAX: [phone]

www.everfocus.com
[e-mail]

EverFocus Japan:

5F, Kinshicho City Building, 2-13-4

Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan

TEL: [phone]

FAX: [phone]

www.everfocus.co.jp

[e-mail]

EverFocus India:

Suite 803, Housefin Bhavan, C-21, Bandra Kurla

Complex, Bandra (East), Mumbai 400051, India

TEL: [phone]

FAX: [phone]

www.everfocus.in

[e-mail]

and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!

und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben

EverFocus Europe - UK:

Unit 12, Spitfire Business Park,

Hawker Road, Croydon Surrey, CR0 4WD, UK

TEL: [phone]

FAX: [phone]

www.everfocusuk.co.uk
[e-mail]

!

August 2013

7