EverFocus EHD360 User Manual

EVERFOCUS

High Resolution Vandal Proof

Weather Resistant 3-Axis IR Dome Camera

Operation Instructions

Model No.

Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.

PRECAUTIONS

1. Do not install the camera near electric or magnetic fields.

Install the camera away from TV/radio transmitters, magnets, electric motors, transformers
and audio speakers since the electromagnetic fields generated from these devices may distort
the video image or otherwise interfere with camera operation.

2. Never disassemble the camera beyond the recommendations in this manual nor

introduce materials other than those recommended herein.

Improper disassembly or introduction of corrosive materials may result in equipment failure
or other damage.

3. Try to avoid facing the camera toward the sun.

In some circumstances, direct sunlight may cause permanent damage to the sensor and/or
internal circuits, as well as creating unbalanced illumination beyond the capability of the
camera to compensate.

4. Keep the power cord away from water and other liquids and never touch the power

cord with wet hands.

Touching a wet power cord with your hands or touching the power cord with wet hands may
result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents.

Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning

For cameras with interchangeable lenses, do not touch the surface of the sensor directly with
the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and
the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do
not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.

7. Do not operate the camera beyond the specified temperature, humidity or power source

ratings. This camera is suitable for indoor and outdoor operation.

EHD360

Use the camera at temperatures within -10°C to +50°C (14°F to 122°F) and in an IP66

CAUTION

compliant environment; this device is not rated as submersible. The input power source is
12VDC. Be sure to connect the proper + / - polarity and voltage, as incorrect polarity or

too high a voltage will likely cause the camera to fail, and such damage is not covered
by the warranty. The use of properly fused or Class 2 power limited type supplies is
highly recommended.

8. Mounting

Use care in selecting a solid mounting surface which will support the weight of the camera
plus any wind, snow, ice or other loading, and securely attach the camera to the mounting
surface using screws and anchors which will properly support the camera. If necessary (e.g.
when mounting to drop ceilings) use a safety wire to provide additional support for the
camera.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK), NO US ER SERVICEABLE PARTS INSIDE.

REFE R SERVI CING TO QUALI FIED SE RVICE P ERSONN EL.

OVERVIEW

The EHD360 is an outdoor, vandal resistant 3-axis IR dome camera which utilizes a Sony 1/3”

Super HAD CCD Sensor to provide high resolution 540TVL color video for security surveillance

applications. Vandal Proof materials and an IP66 weather resistant housing allow reliable

operation in outdoor and indoor environments. True day/night operation combined with 25m

(~80ft.) range high efficiency IR LEDs makes the EHD360 suitable for a wide range of day and

night surveillance situations. Plus, the 3-axis mechanical design and built-in f=3.7~12mm

varifocal auto iris lens bring flexibility to installation and field of view adjustment.

FEATURES

 Color dome camera with SONY 1/3” Super HAD CCD sensor.

 High resolution 540 TVL.

 3-Axis design for flexible fens positioning.

 High sensitivity, low smear, high anti-blooming and high S/N ratio.

 Built-in Auto Gain Control (AGC), Auto Tracing White Balance (ATW).

 Built-in 3.7~12mm varifocal DC-drive auto iris lens.

 25m (~80ft.) range IR-LEDs.

 True day/night auto switching with IR filter removal for B/W images in low light

environments.

 Vandal proof to withstand impact of a 10 pound sledgehammer.

 Weather resistant, IP66 rated.

PACKAGE CONTENTS

1

 Camera Unit x 1
 Mounting kit includes:

-Screws x 4

-Security wrench for housing screws x 1

-Expanding Screws x 4

-Washers x 4

 Operation Instructions (this document) x 1
 Weatherproof bushing x 1
 Power cable x 1
 Video cable x 1
 Power adapter pigtail (for NTSC model only) x 1
 Mounting template x 1

SPECIFICATIONS

Pickup Device 1/3" SONY Super HAD CCD Sensor

Video Format NTSC or PAL (depends on model selected)

Picture Elements 768 x 494 (NTSC), 752 x 582 (PAL)

Horizontal Resolution 540 TVL

Sensitivity 0.12 LUX / F1.6 ; 0 LUX (IR LED ON)

S/N Ratio Over 48dB (AGC off)

Electronic Shutter 1/60(1/50)s~1/100,000s

Video Output BNC 1.0Vp-p 75Ω

Gamma Correction 0.45

Lens Type Vari-Focal 3.7~12mm / F1.4 DC Drive Auto Iris Lens

Day/Night True day/night with motorized IR cut filter

Gain Control Automatic

White Balance ATW (2500°K~9500°K)

Sync. Mode Internal Sync.

IR LED 11 Units High Efficiency IR LED

IR Wavelength 850nm

IR Distance 25m (~80ft.) nominal; depends on environment

Weather Resistant IP 66

Vandal Proof Yes

Power Source 12VDC

Power Consumption 283mA @12VDC

Operating Temperature -10°C~50°C / 14°F~122°F

Dimensions (O.D. x H) 142mm x 115.5mm / 5.6” x 4.55”

Weight 979 g / 2.16 lbs

Certifications CE / FCC

2