EverFocus EDRHD4H4-4 User Manual

User Manual

E

E

N

N

E

((E

D

D

D

D

E

E

R

R

AVV

A

H

H

O

R SS

O

R

D--22

D

D++

D

H1144 // 44

H

H

H

D

D

DVV

D

H44))

H

R

R

EVERFOCUS ELECTRONICS CORPORATION

ENDEA VOR SD+HD D VR

Instruction Manual

 2010 EverFocus Electronics Corp

www.everfocus.com

All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by

any means without written permission of the Everfocus Electronics Corporation.

Release Date: Feb. 2011

QuickTime is a registered trademark of the Apple Computer, Inc.

Windows is a registered trademark of the Microsoft Corporation.

Linksys is a registered trademark of the Linksys Corporation.

D-Link is a registered trademark of the D-Link Corporation.

DynDNS is a registered trademark of the DynDNS.org Corporation.

Other product and company names mentioned herein may be the trademarks of their respective owners.

Safety Precautions

 Refer all work related to the installation of this product to qualified service personnel or system

installers.

 Do not block the ventilation openings or slots on the cover.
 Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the

power off immediately and contact qualified service personnel for service.

 Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or

covers. There are no user-serviceable parts inside. Contact qualified service personnel for
maintenance. Handle the appliance with care. Do not strike or shake, as this may damage the
appliance.

 Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take immediate

action if the appliance becomes wet. Turn the power off and refer servicing to qualified service
personnel. Moisture may damage the appliance and also may cause electric shock.

 Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean

the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.

 Do not overload outlets and extension cords as this may result in a risk of fire or electric shock.
 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do

not use the appliance in an extreme environment where high temperature or high humidity exists. Use
the DVR at indoor type temperatures within 0°C~40°C (32°F~104°F) and at relative humidity between
20%~80%. The input power source for this device is 12VDC though a power supply which operates
from100~240VAC.

 Read Instructions

All the safety and operating instructions should be read before the unit is operated.

 Retain Instructions

The safety and operating instructions should be retained for future reference.

 Heed Warnings

All warnings on the unit and in the operating instructions should be adhered to.

 Follow Instructions

All operating and use instructions should be followed.

 Cleaning

ii

Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or aerosol
cleaners. Use a damp cloth for cleaning

 Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

 Water and Moisture

Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is
classified as a wet location.

 Servicing

Do not attempt to service this unit by yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

 Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, playing particular attention to cords and plugs, convenience receptacles,
and the point where they exit from the appliance.

 Object and Liquid Entry

Never push objects of any kind into this unit through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
unit.

"Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation
instructions:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should
be given to installing the equipment in an environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition
is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

iii

y

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch circuit (e.g. use
of power strips)."

ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in
this case, the user ma

be urged to take adequate measures.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures :

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the users’ authority to operate this equipment.

WEEE

This Product is RoHS compliant.

The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.
Therefore, all specifications are subject to change without prior notice. Manufacturer is not responsible for misprints or typographical
errors.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.

iv

TABLE OF CONTENTS

1 PRODUCT OVERVIEW..................................................................................................... 1

1.1 FEATURES....................................................................................................................... 1

1.2 PACKAGE CONTENTS................................................................................................... 3

1.3 SPECIFICATIONS ........................................................................................................... 4

1.4 FRONT

1.5 REAR

2 INSTALLATION................................................................................................................ 11

2.1 HD-CCTV WIRING FOR VIDEO INPUTS ............................................................................. 11

2.1.1 Understanding HD-CCTV signals and wiring ......................................................................................11

2.1.2 HD-CCTV signal...................................................................................................................................11

2.1.3 Cable types............................................................................................................................................12

2.1.4 Cable installation..................................................................................................................................13

2.1.5 BNC-plug...............................................................................................................................................13

2.1.6 Extended cable lengths with repeater EHA-RPT / converter EHA-SRX ...............................................13

2.1.7 Extended cable lengths with fiber optics transmission..........................................................................14

2.1.8 MONITOR INSTALLATION..................................................................................................................15

2.2 AUDIO INSTALLATION .............................................................................................. 15

2.3 ALARM CONTACTS INSTALLATION....................................................................... 16

2.3.1 Alarm Input Contacts............................................................................................................................16

2.3.2 Alarm Output Relay...............................................................................................................................16

2.4 RS-485 KEYBOARD / PTZ INSTALLATION......................................................................... 16

2.4.1 General RS-485 bus installation ...........................................................................................................17

2.4.2 RS-485 ports..........................................................................................................................................18

2.4.3 EKB-500 connection with network patch cable.....................................................................................18

2.4.4 EKB-500 connection to several DVRs...................................................................................................18

2.4.5 Speed Dome Installation .......................................................................................................................18

2.5 USB-M

2.6 NETWORK

2.6.1 Direct PC Connection through Crossover Network Cable ...................................................................19

2.6.2 Network Connection through Patch Cable............................................................................................20

2.7 FINAL

PANEL ................................................................................................................ 6

PANEL................................................................................................................... 9

OUSE INSTALLATION ............................................................................................ 19

CONNECTION .......................................................................................... 19

INSTALL PROCESS.......................................................................................... 21

3 MOUSE AND FRONT PANEL OPERATION ............................................................... 22

3.1 GENERAL USB MOUSE OPERATION....................................................................... 22

3.1.1 How to select a channel / Enable audio................................................................................................22

3.1.2 OSD Root Menu.....................................................................................................................................22

3.1.3 Operation in the Configuration Menus.................................................................................................23

3.1.4 Field Input Options ...............................................................................................................................23

2.2 G

2.2.1 How to select a channel / Enable audio.......................................................................................................25

2.2.2 OSD Root Menu ...........................................................................................................................................25

2.2.3 Front Panel Key Review...............................................................................................................................25

ENERAL FRONT PANEL OPERATION ............................................................................... 25

v

2.2.4 Operation in Configuration Menu.........................................................................................................25

2.2.5 Field Input Options ...............................................................................................................................26

3. GENERAL DVR OPERATIONS...................................................................................... 28

3.1 RECORD......................................................................................................................... 28

3.2 LOGIN............................................................................................................................. 28

3.3 SELECT CAMERA OPERATION................................................................................. 29

3.5 PLAYBACK.................................................................................................................... 30

3.6 PTZ.................................................................................................................................. 31

3.6.1 General PTZ control (if PTZ cameras are installed)..................................................................................31

3.6.2 Express Control of PTZ.........................................................................................................................32

3.7 LAYOUT......................................................................................................................... 34

3.7.1 Bring a camera to full screen mode.......................................................................................................34

3.8 CHANNEL

SWITCHING............................................................................................... 34

3.9 DISPLAY ........................................................................................................................ 35

3.10 SEQUENCE.................................................................................................................. 35

3.11 ZOOM........................................................................................................................... 35

3.12 SEARCH....................................................................................................................... 36

3.12.1 Time Search...........................................................................................................................................37

3.12.2 Event Search..........................................................................................................................................37

3.12.3 Smart Search .........................................................................................................................................38

3.12.4 Snapshot Search ....................................................................................................................................41

3.13 COPY............................................................................................................................ 43

3.14 LOGOUT...................................................................................................................... 44

4 DVR CONFIGURATION.................................................................................................. 45

4.1 CONFIGURATION MENU............................................................................................ 45

4.2 EXPRESS........................................................................................................................ 45

4.3 CAMERA SETTING ...................................................................................................... 48

4.3.1 Basic Setting..........................................................................................................................................48

4.3.2 Video Adjust (apply to analog camera only).........................................................................................50

4.3.3 Motion ...................................................................................................................................................51

4.3.4 Video Loss.............................................................................................................................................54

4.4 RECORD & PLAY SETTING........................................................................................ 56

4.4.1 Record...................................................................................................................................................56

4.4.2 Built-in Calculator ................................................................................................................................57

4.4.3 Play .......................................................................................................................................................58

4.5 ALARM & EVENT SETTING....................................................................................... 59

4.5.1 Alarm .....................................................................................................................................................59

4.5.2 Event......................................................................................................................................................61

4.6 SCHEDULE SETTING................................................................................................... 69

4.6.1 Express Setup .......................................................................................................................................69

4.6.2 Holidays ................................................................................................................................................70

4.6.3 Schedule ................................................................................................................................................71

4.6.4 Alarm Action .........................................................................................................................................76

4.7 NETWORK SETTING.................................................................................................... 80

4.7.1 LAN .......................................................................................................................................................80

4.7.2 EMAIL...................................................................................................................................................82

vi

4.7.3 DDNS ....................................................................................................................................................83

4.7.4 Alarm Server .........................................................................................................................................85

4.7.5 Network Test..........................................................................................................................................86

4.8 DISK

4.8.1 Disk .......................................................................................................................................................87

4.8.2 Lock/Format..........................................................................................................................................88

INFORMATION................................................................................................... 87

4.9 DISPLAY SETTING....................................................................................................... 89

4.9.1 Monitor OSD.........................................................................................................................................89

4.9.2 Main M/T SEQ ......................................................................................................................................90

4.10 SYSTEM SETTING..................................................................................................... 91

4.10.1 Date/Time..............................................................................................................................................91

4.10.2 Daylight Saving.....................................................................................................................................92

4.10.3 User.......................................................................................................................................................93

4.10.4 I/O Control ............................................................................................................................................96

4.10.5 Misc. ......................................................................................................................................................97

4.11 INFORMATION........................................................................................................... 99

4.11.1 System....................................................................................................................................................99

4.11.2 Log.......................................................................................................................................................100

5 NETWORKING OVERVIEW........................................................................................ 102

5.1 INTRODUCTION TO TCP/IP............................................................................................. 102

5.2 SUBNET MASKS.............................................................................................................. 102

5.3 GATEWAY ADDRESS....................................................................................................... 102

5.4 VIRTUAL PORTS.............................................................................................................. 103

5.5 PRE-INSTALLATION ........................................................................................................ 103

5.6 WHAT IS YOUR NETWORK SETUP?.................................................................................. 104

5.7 SIMPLE ONE TO ONE CONNECTION................................................................................. 105

5.8 DIRECT HIGH SPEED MODEM CONNECTION ................................................................... 110

5.9 ROUTER OR LAN CONNECTION...................................................................................... 112

6 REMOTE OPERATION FROM BROWSER.................................................................... 115

6.1 CONNECTING TO ENDEAVOR SD+HD ...................................................................... 115

6.2 BROWSER SECURITY SETTING .................................................................................. 116

6.2.1 Installing ActiveX controls..................................................................................................................116

Enabling ActiveX Controls..................................................................................................................................119

6.3 REMOTE LIVE VIEW................................................................................................. 122

6.4 REMOTE PLAYBACK................................................................................................ 124

7 EVERFOCUS DDNS SETUP.......................................................................................... 125

8 LINKSYS & D-LINK PORT FORWARDING ............................................................. 127

8.2 TYPICAL LINKSYS PORT FORWARDING

8.3 TYPICAL

D-LINK PORT FORWARDING ................................................................ 129

............................................................. 127

9 TROUBLESHOOTING

................................................................................................... 132

APPENDIX A: TIMING OF ALARM MODES.................................................................... 134

APPENDIX B: EXPRESS SETUP RECORDING VALUE SELECTION RULES .......... 137

vii

APPENDIX C: REMOTE CONTROL................................................................................... 139

viii

Chapter

1

1 PRODUCT O VERVIEW

Begin your migration to the High Definition revolution in CCTV technology without changing your
installation methods. For definitive identification in critical areas, capture scenes with stunning HD

clarity; for traditional applications connect standard definition analog CCTV cameras. Carry uncompressed
full motion MEGAPIXEL DIGITAL and analog NTSC video back to their respective inputs on the

ENDEAVOR HD+SD DVR over standard coaxial cable*! Attach familiar BNC connectors to both HD-CCTV

and analog cameras and to the ENDEAVOR HD+SD DVR, then display live and recorded images in

astounding detail on the HDMI main monitor screen. HD-CCTV with up to 6 times the resolution of the
analog cameras delivers the ability to zoom with clarity. HD images are so detailed, each sends a 1.5Gb/s
uncompressed digital video signal over the coax; the Endeavor HD – 2H14 DVR can process that total of

3Gb/s from 2 HD-CCTV cameras, as well as the video from 14 analog cameras, for live viewing and H.264
recording at HD resolutions of 1080p (~2 megapixel @ 15 fps/camera) or 720p (~1 megapixel @ real time

30fps/camera), plus real time 30FPS at D1 recording capability on all 14 analog cameras. Dedicated

mega-bandwidth coax signal paths from each HD camera to this HD Hybrid DVR eliminate the need for
compression, addressing, and complex network design.

The ENDEAVOR HD+SD DVR is a powerful, full featured, embedded DVR with all the capabilities, familiar
front panel controls, user friendly mouse driven Graphical User Interface, plug-and play ease of installation
and setup and proven, reliable Linux based operating system that you expect from a state of the art
EverFocus DVR. More than that, it is designed and built in our factory, backed by our Support Team, and
carries our standard three year DVR warranty (including the hard drives). Start adding some High Definition
Security Surveillance to your systems at your own pace, with a name you know and trust: the ENDEAVOR
HD+SD DVR from Everfocus Electronics puts the future in your hands – TODAY!

*Up to 500’ nominal for digital signals on RG59; more with lower loss cable and/or optional repeaters.

1.1 FEA TU RES

o Both HD-CCTV Megapixel Video Inputs and Analog Video Inputs
o Choose 720p or 1080p HD resolution recording for HD-CCTV Video Inputs up to 30 FPS/camera
o H.264 Compression format to minimize optimize disk space consumption
o Dual streaming to optimize remote viewing bandwidth utilization
o Real time recording rate and playback rate – up to 30fps@D1 on analog and 30fps@HD on HD-CCTV
o Recording resolution and rate can be set independently for each camera, and changed via user defined

schedule

o Multiple Main Monitors : HDMI 1080p / VGA (1920x1080) output for stunning image clarity
o Pentaplex Operation (Simultaneous live, recording, playback, archiving and remote viewing)

1

o User friendly GUI with graphical icons and visual indicators
o Free EverFocus DDNS Service static IP address is not required for reliable remote access
o Supports eSATA external HDD array (EDA450)
o Supports remote/mobile monitoring via PC browsers, SmartPhones and iPhone/Android apps
o Multiple Control Inputs: mouse/front panel/ IR remote control/EKB500 keyboard
o Express Setup: A unique menu option for quick & easy installation and setup
o Express Playback: Simply point, click and drag the playback bar to view desired recordings
o Express Archive: Archive video instantly (to USB) while playing back
o Express Search: Use the intuitive playback bar with simple drag & drop operations
o Smart Search: Review recorded video to identify motion in area(s) of interest
o Snapshot search: choose an interval and direction, view a series of snapshots to quickly isolate

incidents

o Remote configuration support from built-in web interface
o Gigabit Ethernet interface for remote network viewing and control
o Audio recording capabilities
o Up to 4 internal HDDs
o Built-in DVD burner
o 2 USB 2.0 ports for video archive and mouse usage
o Multi-language support
o Watermark capabilities to identify intentional modifications of recorded data
o Compatible with FREE EverFocus Central Management Software
o USB Mouse and IR remote control included
o 19” Rack mountable – rack ears included

2

1.2 PACKA GE CONTENTS

Standard Package

-Digital Video Recorder x1

-User Manual x 1

-Power Cord x1

-Mouse x 1

-19” Rack mounting adapters (pair) x 1

-Terminal Block x 5

-IR Remote Control x 1

-Battery x 2

-Audio-in connector (D-sub to RCA) x 1

-HDD Fixing Bracket x 4 set

-SATA cable x 4

-Screws x 16 for HDD

-Screws x 8 for HDD fixing bracket

3

1.3 SPECIFICA TIO NS

ENDEAVOR HD+SD DVR

EDR HD-2H14 EDR HD-4H4
HD-CCTV Camera Inputs 2 BNC SMPTE292m compliant 4 BNC SMPTE292m compliant
Analog Camera Inputs 14 BNC 4 BNC

Looping Analog Camera Outputs 14 BNC 4 BNC
Compression Format H.264

Dual Streaming Yes (Configurable)
HD Recording Rate/Resolution

Choose one resolution for both channels

Analog Recording Rate/Resolution

Resolution and rate can be set independently
per camera up to the total D1 recording
capacity

HD Playback Rate/Resolution

Analog Playback Rate/Resolution

Mobile View
Pentaplex Operation Simultaneous Live, Recording, Playback, Archive and Remote

Main Monitor Outputs

(simultaneous display)

Audio Inputs 16 Inputs (RCA, line level) 8 Inputs (RCA, line level)
Audio Outputs 2 Outputs (RCA, line level)

Recording Modes Manual, Schedule and Event
Playback Search Date/Time, Event, Tex, Smart, Snapshot
Alarm Inputs 16 8
Alarm Outputs 4 Alarm Outputs – Form “C” rated at 30VDC, 1A
Video Pause Yes
Video Loss Detection Yes
Motion Detection Yes
Event Log Yes
Watch Dog Timer Yes
Internal HDD Support 4 Internal HDD (up to 8Tb max at time of printing)
External HDD Support 1 eSATA
DVD Drive DVD RW Built In
User Interface Color GUI (Graphical User Interface)
OS Embedded Linux
Network/Protocol Gigabit Ethernet; TCP-IP / DHCP/ PPPoE / DDNS / UDP / SMTP /

Control PTZ via OSD Local and via web interface

1080p 30fps NTSC / 25ps PAL 60fps NTSC / 50ps PAL
720p 60fps NTSC / 50ps PAL 120fps NTSC / 100ps PAL

D1 420fps NTSC / 350ps PAL 120fps NTSC / 100ps PAL
1080p Up to 30fps NTSC / 25fps PAL Up to 60fps NTSC / 50fps PAL

720p Up to 60fps NTSC / 50fps PAL Up to 120fps NTSC / 100fps PAL
D1 Up to 420fps NTSC / 350fps

Up to 120fps NTSC / 100fps PA

PAL

Live view on PDA or Smart Phones (MobleFocus FREE app for iPhone®
and Android™) plus various web browsers

Viewing

1080p HDMI (socket Type A 19 pin female) and

VGA 1920 x 1080 @ 60 Hz (D-Sub socket 15 pin female)

SSL / HTTP / NTP/ ICMP / ARP

4

USB 2 Front Panel USB 2.0 port
Schedule Setting Support Express and Advanced Schedule Setting
User Access 3 Levels of User Access Support
RS-232 9-pin D-Sub socket (male)
RS-485 1 RS485 (2 RJ45 connector)
Power Source 100VAC~240VAC
Power Consumption 110W max. with 4 x HDD
Dimensions (L x W x H) 423 x 430 x 79.5 mm / 16.6" x 16.9" x 3.2"
Temperature 0°C~40°C / 32°F~104°F (20~80% humidity)

Certificates CE, FCC, UL (pending)
Supported PTZ Protocols EverFocus, Pelco D, Pelco P, Samsung, Transparent

5

1.4 FRONT PANEL

Your primary interaction with your new DVR will be through the Front Panel buttons and their

corresponding buttons on the included IR Remote Control. Take a moment to learn where the keys are as

the remainder of the manual will refer to them often.

Figure 1-1 Front Panel

23

6

1) Remote Control Receiver: Receiver for IR remote control

2) Channel keys 1~16: Press channel key (CH1~CH16) to display that channel in full screen view.

CH1~CH14 are analog video. CH15 and CH16 are HD-CCTV video.

3) Channel keys 1~8: Press channel key (CH1~CH8) to display that channel in full screen view.
CH1~CH14 are analog video.

4) DVD Eject: Press this button to eject the DVD.

5) View: Press this key to switch between 4x, PiP (Picture In Picture),full screen, 6x, 7x, 8x, 9x, 10x, 13x

and 16x.

6) SEQ: Press this key to enter the auto sequential switching mode. The sequence dwell time can be set in
“Display Setting” tab of the Menu.

7) Display: Press this key to switch display of channels and status bar.

8) Monitor: Switch between Main monitor and Call monitor (Function reserved).

9) Zoom: In full screen mode, 2x and 4x electronic zoom. Zoom screen can be moved through arrow keys.

Pressing the Menu/ESC key again switches the electronic zoom off.

10) Menu Navigation Keys: Instead of or in combination with a mouse, you can use these keys to change
the Menu settings.

11) Copy: Press this key to enter Copy Menu

12) JOG/SHUTTLE: Shuttle (outer wheel): In playback mode, use the SHUTTLE for fast forward / fast

reverse playback.
JOG (inner wheel): In PAUSE mode, use the jog to move frame by frame. Within
menu functions, use the jog to adjust the values / parameters. Use Jog to highlight
individual cameras. Use either Shuttle or Jog to switch between MENU

Jog

parameters.

Shuttle

13) System LED
POWER: LED indicating power on
HDD: LED indicating HDD active
Alarm: LED indicating Alarm active
Network: LED for network traffic
Record: LED indicating Record active

7

14) Search: Press this key to enter Search Menu

15) Menu/ESC: Press this key to enter/exit MAIN SETUP MENU

16) DVD burner: DVD+RW burner

17) ►►/I►: Fast Forward playback or step forward playback depending on playback mode

18) ►/ I I: Forward playback or pause

19) ■ : Stop playback

20) I I / ◄: Reverse playback or pause

21) ◄I /◄◄: Fast reverse playback or step reverse playback depending on playback mode

22) USB ports: Use one port for connecting USB-Flash-Drive to copy/archive video or for firmware

upgrades. Use the other port for connecting the mouse.

23) Ear-mount: Use two M3 screws (φ6.8) to fix the ear-mount.

8

1.5 REAR PANEL

During initial setup you will be connecting your DVR to multiple input and output devices. This is done

through the rear panel.

Figure 1-2 Rear Panel

1) Main POWER: Plug the 120~240VAC power source provided into the power socket.

2) ETHERNET: RJ-45 network connection 10/100Mbps Ethernet. There are two LEDs on the LAN jack;

Green LED means network is connected, amber LED flickers when data is being exchanged.

3) RS232 Connector: 9-pin D-Sub control input for RS-232.

4) RS485 Connectors: For remote control via RS-485 keyboards and telemetry control for attached PTZ

devices

9

5) VGA Main Monitor Out: Connect a VGA monitor to the VGA output connection. DVR can auto detect

the best resolution from the connected VGA monitor. If DVR detection fails, the default resolution will be
1920x1080 60Hz vertical, 68 KHz horizontal.

6) HDMI Main Monitor Out: Provides an uncompressed all-digital video interface between the HD DVR

and HDMI-compatible monitor. HDMI output format is 1920x1080p 60Hz vertical, 68 KHz horizontal.

7) Alarm In: Connect up to 16 alarm inputs, selectable between N.O./N.C. contacts.

8) Alarm Out: N.C or N.O type alarm out (form “C”).

9) Audio In 4x RCA, others on DIN connector: Connect line level output of an audio preamplifier to the

audio input connection corresponding to the appropriate camera.

10) Audio Out: Connect to the line level input of an audio amplifier.

11) HD-CCTV Video In (CH15~16) (2H14 only): Connect HD-SDI camera’s video output (CH15~16) or

other HD-SDI video source to the video input connection.

12) HD-CCTV Video In (CH5~8) (4H4 only): Connect HD-SDI camera’s video output (CH5~8) or other

HD-SDI video source to the video input connection.

13) Analog Video Input and looping (CH1~14) (2H14 only): Connect camera’s video output (CH1~14) or

other composite video source to the video input connection.

14) Analog Video Input and looping (CH1~4) (4H4 only): Connect camera’s video output (CH1~4) or

other composite video source to the video input connection.

15) eSATA: Used for external SATA HDD bay. Note: Hot-swappable model does not support eSATA.

10

2 Installation

2.1 HD-CCTV wiring for video inputs

2.1.1 Understanding HD-CCTV signals and wiring

Even if EverFocus HD-CCT
technology - the requirements for wiring and cable types are some different.

This chapter explains some basic facts for HD-CCTV signals and cable requirements.

2.1.2 HD-CCTV signal

V equipment uses coaxial cable and BNC type plugs similar to standard CCTV

In result to the high resolution and uncompressed image transmission from the camera high frequencies
are used for HD-CCT
EverFocus HD-CCTV technology is mostly based on the SMPTE-292M standard, which defines HD-SDI
(High Definition - Serial Digital Interface) video transmission.
In classic CCTV video standards PAL/NTSC the frequency bandwidth is < 6MHz for high resolution
cameras.
HD-CCTV works with up to 1.5 GHz, so this technology requires ~ 250 times higher frequency than
PAL/NTSC based CCTV.
The figure below shows the basic timing and signal levels of a full HD (1920x1080) signal:

V signal transmission.

Timing of HD-SDI signal ("Eye"-diagram)

The diagram shows the total difference of HD-CCTV signals to classic NTSC or PAL signals.

11

Well known signal parts such as Sync, Burst and others do not exist here.
The high frequencies do not allow a signal evaluation by standard oscilloscopes or other standard video
measurement tools. Only quite expensive HD-SDI analyzers and upscale HF - oscilloscopes could be used
here. In most cases such equipment is not available at installation site.
For this reason a careful specification of the cable type is mandatory for system planning, especially in
applications with long cable distances.

2.1.3 Cable types

The short description of HD-SDI signals above explains, why high frequency attenuation of the used video
cable has a high influence on the achievable maximum cable length. Further on also the Return Loss of the
coaxial cable and plug influences signal stability.

The standard RG-59 cable types - the most common in the CCTV industry - are originally designed for
lower frequencies.

However, due to the new optimized receiver interfaces of EverFocus HD-CCTV equipment it is also
possible to use standard RG-59 cable for distances of over 100m.
High quality, low loss RG-59 cable types allow distances up to 160m.

Longer cable distances can be achieved with low loss RG-6 or RG-11 type coaxial cables.
Generally are cable types with 75 Ω impedance required.

Attenuation at 1 GHz: < 32 dB per 100m (328 feet)
Return Loss attenuation: > 20 dB
Impedance: 75 Ω

The table below gives an orientation for achievable cable distances:

Cable Type Attenuation in dB at 1

GHz per 100 m / 328 ft

Max. Cable distance in
m ft

RG-59 24 ~ 40 * 70 ~ 160 230~520

RG-6 15 ~ 35 * 100 ~ 190 330~620

RG-11, CATV-

8 ~ 16 * 180 ~< 250 590~<820

lowloss cables

* Low quality cable may have higher attenuation

12

2.1.4 Cable installation

Please make sure, that the coaxial cable is not squeezed at any position.
Also the max. bending radius defined by the cable manufacturer should be considered.

General rule: maximum bending radius = 10 x outer cable diameter

Bending creates pressure on the center conductor, causing it to move through the dielectric toward the
inside of the bend. This affects impedance and return loss and reduces the maximum possible cable length.

Please try to avoid any BNC - adapter or any connectors in the BNC cable.
Looping HD-SDI signals by BNC T-connectors to other devices is not possible.

2.1.5 BNC-plug

Also the BNC - plug plays an important role for clear HD-CCTV signal transmission.
Standard BNC plugs for CCTV have a quite high attenuation and may cause return losses due to reflection
effects.
We recommend using of HD-Video approved BNC plugs.

2.1.6 Extended cable lengths with repeater EHA-RPT / converter EHA­SRX

The maximum cable distance between camera and DVR and DVR / repeater can be doubled by installing
EHA-RPT in the video line. EHA-SRX is a combined HD-SDI cable extender and HD-SDI to HDMI
converter.
The HD-SDI output of EHA-SRX allows adding one more complete coaxial cable length.

* max. coaxial cable depends on installed cable type

13

2.1.7 Extended cable lengths with fiber optics transmission

The maximum distance between camera and receiving device can be extended by fiber optics cable.
The transmitters and receivers are available for multi-mode and single-mode fiber cables:

EHA-FTX-MM: Fiber optics transmitter multi-mode, max. transmission distance 500 m
EHA-FTX-SM: Fiber optics transmitter single-mode, max. transmission distance 21 Km
EHA-RTX-MM: Fiber optics receiver multi-mode, max. transmission distance 500 m
EHA-RTX-SM: Fiber optics receiver single-mode, max. transmission distance 21 Km

max. coaxial cable distance *

12 VDC

HD-SDI In

EHA-FTX

Fiber Optical Cable

EHA-....X-MM:Multi Mode - up to 500 m

EHA-....X-SM: Single Mode: up to 21 Km

Fiber out

max. coaxial cable distance *

12 VDC

Fiber in

12 VDC

HD-SDI Out

EHA-FRX

* max. coaxial cable depends on installed cable type

The fiber optics interface of EHA-FTX / EHA-FRX requires LC type plugs for the fiber optics cable.

14

2.1.8 MONITOR INSTALLATION

The ENDEAVOR SD+HD DVR provides 2 main monitor outputs with identical functionality - VGA and HDMI.
Both outputs can be used simultaneously and deliver full HD output resolution (1920x1080, progressive, 60
Hz. vert., 68 KHz hor.).
Make sure that the connected monitor's specifications comply with these resolution requirements.

Please do not exceed the max. HDMI cable length of 15 m.
For cable length up to 3 m standard HDMI cables mostly work well, for longer distances (especially in the
15m range) please use only high quality HDMI cable.

2.2 AUDIO INSTALLATION

EDR HD-2H14 DVR provides 16 line level audio inputs and 2 line level audio outputs. EDR HD-4H4
provides 8 line level audio inputs and 2 line level audio outputs. The first 4 audio outputs are RCA
connectors, the rest are on DIN connectors.

Audio out 1 is for local audio output, whereas Audio out 2 is reserved for the audio transmitted from the
remote site back to the DVR.

ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone
amplifier is required). The audio output requires an amplifier to drive a speaker or headphones.

The installation must be connected with audio coax cable and RCA plugs.

AUDIO RECORDING FUNCTIONALITY:

15

Audio recording is activated / deactivated in the Camera Menu for Camera #1~16 respectively. Please
check and always comply with local laws and regulations when using audio recording.

The audio channel is always recorded together with video and is independent of the image recording rate.
Though the audio record control is done in the Camera #1~16 screen, there is no specific camera
allocation.

2.3 ALARM CONT A CTS INSTALLATION

The alarm inputs can be used to start recording or for recording rate adjustment. In addition, alarm
reactions such as camera display on the monitor, buzzer, e-mail and network alarm are available. The
alarm output relay can be switched if required. Alarm input response actions can be controlled according to
a flexible schedule.

2.3.1 Alarm Input Contacts

This DVR provides one alarm input per camera. All inputs are programmable N.O. (Normal Open) or N.C.
(Normal Closed) Inputs have to be switched by dry contacts.

Alarm input with N.O. (Normal Open) contact Alarm input with N.C. (Normal Closed) contact
in idle state in idle state

All settings are programmed in the ALARM menu (Section 0).

2.3.2 Alarm Output Relay

The relay output provides either Normally Open or Normally Closed dry contacts.

Output relay in idle state

2.4 RS-485 keyboard / PTZ Installation

All functions can be remote-controlled by the EKB-500 universal keyboard. Using the EEPbus protocol,
digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One
system can comprise up to 8 keyboards.

16

2.4.1 General RS-485 bus installation

The EKB-500 keyboard uses a RS-485 simplex wiring; the signal is transferred via a single twisted pair line.
CAT5 network cable is recommended, UTP version (unshielded) is sufficient for normal applications. A
shielded cable should be used if the installed cables are expected to be highly susceptible to interference.
The number of devices installed in one bus is limited to 32, and the maximum cable length is 3,900 feet.
Both of these can be expanded using a signal distributor EverFocus Model EDA997A (see below).

Both the first and the last device in series should be terminated with 120 Ohm resistance in order to
minimize line reflections.

RS-485 bus serial wiring

Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes.

RS-485 bus serial wiring with connector boxes and connection cable

Direct RS-485 bus star wiring is not supported unless using an EverFocus Model EDA997A (see below).

Improper RS-485 bus star wiring

An EDA997A RS-485 signal distributor may be used to use a star wiring configuration.

Star wiring with RS-485 signal distributor

17

A RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as
the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an
additional 1200m, and it also enables the additional connection of 31 further devices to each output (the
output itself represents one device).
The maximum system expandability depends on the RS-485 address range of the installed devices.

System expansion with RS-485 signal distributor

ATTENTION: EDA997A signal distributors are unidirectional! This means that the signal only flows from
the input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with
these types of signal distributor!

2.4.2 RS-485 ports

This DVR provides two independent RS-485 ports with 2 RJ-45 plugs each (loop-through).

2.4.3 EKB-500 connection with network patch cable

For a simple, short distance installation, recorder and keyboard can be connected directly using a standard
CAT5 network cable with an 8-pin connector at only one end, and at the other end the Pin 3 wire connected
to RS485 “+” (plus) and the pin 6 wire connected to RS-485 “-“ (minus).

2.4.4 EKB-500 connection to several DVRs

For long distance installations connecting several DVRs, please use an EDA997A signal distributor to
connect. For further details on keyboard connection, please refer to the EKB-500 manual.

RS-485 port communication settings are configured in the I/O CONTROL menu (Section 5.10.4 System

Setup: I/O - control).

2.4.5 Speed Dome Installation

Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional
PowerCon software if the DVR is connected to a network. Local telemetry control is provided by USB ­mouse control or by the optional EKB-500 keyboard.

Supported protocols: EverFocus, Pelco-D, Pelco-P, Samsung, Transparent

18

Required DVR settings: RS-485 receiver address in CAMERA menu

(Section 4.3)

RS-485 parameters and protocol in the I/O CONTROL menu

(Section 5.10.4)

ATTENTION: Some Pelco-

D / -P protocol domes and receivers require an address offset of -1, i.e. the
address assigned to the dome / receiver in the DVR camera menu must be 1 below the address set in the
dome / receiver itself!

2.5 USB-Mouse installation

Connect the USB mouse to one of the 2 USB ports. (This can be done while DVR is powered on) The rear
USB V1.0 port is recommended to reserve the higher speed front USB V2.0 port for video copy/export.

NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless
USB mouse is not supported.

2.6 NETWORK CONNECTION

This section only describes physical connection to an Ethernet network. This step must be completed
before the DVR can connect to the network. There are two basic types of connection:

2.6.1 Direct PC Connection through Crossover Network Cable

The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of
connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a
10/100Mbps compatible network connection.

Figure 2-1 Direct PC Connection

19

Pinout of crossover-cable

2.6.2 Network Connection through Patch Cable

The connection to an existing network requires a normal patch cable (straight-through). Th
shows the connection to a network switch or router.

Figure 2-2 Network Connection through Patch Cable

e illustration

Pinout of straight patch cable

20

2.7 FINAL INSTALL PROCESS

Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in
the power source. The POWER LED will light up if power is normal. Once the system has finished loading,
you can begin to set up the menu options for the DVR.

21

Chapter

3

3 MOUSE AND FRONT P ANEL OPERATION

ENDEAVOR SD+HD DVRs support multiple sources to control the DVR. It can be controlled with a mouse,
the front panel, an EKB500, and the handheld IR remote control.

This chapter will cover the basic operation using the mouse and the front panel buttons.

3.1 GENERAL USB MOUSE OPERA TION

3.1.1 How to select a channel / Enable audio

1. In a view consisting of more than one channel, users can select a channel by clicking once on the

desired channel screen. The selected screen will be highlighted by a white frame.

2. Double clicking on a channel screen will display full screen for this channel.

3. To enable audio out, click the audio icon (ex: ) at lower side of the screen. This system has only

one audio out. Click this button to enable or disable the audio-out mode.

3.1.2 OSD Root Menu

1. Right-click the mouse to obtain the DVR menu bar (see Figure 3-1 OSD Root Menu ). When you move
the mouse over each icon, its title will be displayed at the top of the control bar.

Figure 3-1 OSD Root Menu

2. Click on any icon to perform that action. These actions are covered in detail in Chapter 3.

3. Click the “X” in the top-right corner to close the DVR control bar.

22

3.1.3 Operation in the Configuration Menus

Click on the

icon to access the Configuration Menu.

The Configuration menu screens (shown in Figure 3-2 OSD Menu) are divided into 3 main sections.

1

2

3

Figure 3-2 OSD Menu

1. In section 1, there are ten setup options available. Move the mouse over an icon and click to select it.

2. In section 2, the choices for the selected icon will be displayed. Click on a choice to select it.

3. In section 3, all the options for the selected choice will be available. Click on a field to make changes.

3.1.4 Field Input Opt

ions

The following are examples of different types of fields available in the Configuration menu.

Textbox: Click on the box and an on-screen keyboard will appear*. (see note about

the on-screen keyboard below)

Dropdown box: Click on the down arrow to see all selections, then

directly click on an option to select it.

Check box: Click on the box to enable it (checked) or disable it (unchecked).

Button: Click the button to execute the function.

23

Bar: Click and hold on the bar to adjust the set point Left or Right.

* Note about on-screen keyboard:

Click on a button to input that character.
The buttons on the right and bottom have the following functions:

Space Enter a space

Caps Switch to capital letters

Delete the letter

Confirm the selection

Move to right

Move to left

24

2.2 General Front Panel Operation

2.2.1 How to select a channel / Enable audio

1. In a view consisting of more than one channel, press the arrow keys (Up/Down/

Right/Left) to scroll
through each channel that is displayed. The selected channel will be highlighted by white frame.
Pressing the “left” or “right” arrow when the last/first camera (1,4, 9 or 16) is highlighted will select all
cameras.

2. While channel #1 is selected, press the “Enter” button to turn Audio On/ Off.

2.2.2 OSD Root Menu

1. Press “Me

nu” key to display the DVR menu bar. Use the left/right arrows to scroll over each icon. The

title for each icon will be displayed on top of the menu bar.

2. Press “Enter” key on any icon to perform that action. These actions are covered in detail in Chapter 3

3. Press “Menu” to close the DVR menu bar.

2.2.3 Front Panel Key Review

The basic principle of front panel operation is to use arrow keys to navigate among the menu items. Use
the “Enter” key to confirm a selection or enter the next level menu. Press the “Menu” key to enter the Main
Menu or exit from the current level of the menu.

2.2.4 Operation in Configuration Menu

Press “Menu”, use the arrow keys to highlight the “Configuration” icon, and press “Enter” with
“Configuration” icon highlighted to bring up the Configuration menu.

NOTE: If the require password option is active, you will need to log in first. Refer to “Section 3.2 LOGIN” for
information on logging in. The menu (shown in

Figure 3-3 OSD Menu ) is divided into 3 main sections.

25

1

2

3

Figure 3-3 OSD Menu

1. In section 1, there are ten setup options available. Use arrow keys to highlight an icon and press “Enter”
to select it.

2. In section 2, the main choices for the selected icon will be displayed. Use Up/Down arrow keys to
highlight a choice and press “Enter” to select it.

3. In section 3, all the options for the selected choice will be available here. Use arrow keys to move
between items and press “Enter” to make changes to that item.

Note: press the “Menu” button to go back to the previous menu section/level.

2.2.5 Field Input Options

Textbox: Press Enter key and an on-screen keyboard will appear*. (see

note about on-screen keyboard below)

Dropdown box: Press “Enter” key to show the available options. Use

arrow keys to highlight the desired option and press “Enter” again to select it.

Check box: Press “Enter” key on a setting to enable it (checked) or disable it (unchecked).

Button: Press “Enter” key to execute the function.

26

Bar: Press “Enter” key to activate the slider, then use arrow keys to adjust the setting.

Press “Enter” again to finalize the changes.

* Note about on-screen keyboard:

Use the arrow buttons to highlight each character and press the “Enter” key on the front panel to input the

selected characters. When finished, highlight “Done” and press the “Enter” key on the front panel to

confirm. The buttons on the right and bottom have the following functions:

Space Enter a space

Caps Switch to capital letters

Delete the letter

Confirm the selection

Move to right

Move to left

27

Chapter

3

3. GENERAL DVR OPERATIONS

This chapter introduces the operations on major functions including playback, layout change, sequence,
triplex operations, copy, and search.

3.1 RECORD

By default, the DVR will always be in record mode. When the DVR is turned on, it will start to record. The
exceptions are:

1. DVR will not record any uninstalled cameras (Refer to Section 4.3.1 for more details)

2. If a schedule is active, the DVR will follow the record settings of the schedule.

3.2 LOGIN

In order to access ENDEAVOR SD+HD options, users may be asked to log in for authority identification. To
log in, follow these steps.

1. Right click on the screen or press the Menu Key to display the Main Menu

2. Choose or click (or press “Enter” key) on the Configuration icon to bring up the following screen:

Figure 3-1 Login page

3. Select the user name from the drop-down list and input the password. The defaults are:

User name: admin (lower case)

Password: 11111111

28

+ To input password by mouse: click the password field to bring up the on-screen keyboard (see Figure 3-2
On-screen Keyboard). Click on each button to input the desired characters for the password. When finished,

click “Done” on the on-screen keyboard to confirm the password.

+ To input password using front panel: use the arrow keys to select the password field, then press the
“Enter” key to show the on-screen keyboard (see Figure 3-2 On-screen Keyboard). Use the arrow buttons
to highlight each character and press the “Enter” key on the front panel to input the selected characters.

When finished, highlight “Done” and press the “Enter” key on the front panel to confirm the password.
+ Click (or press “Enter” key when highlighted) on the “Login” button to log in to the system.

Figure 3-2 On-screen Keyboard

3.3 SELECT CAMERA OPERATION

ENDEAVOR SD+HD is a pentaplex DVR; users can control each camera individually by selecting that
camera. For camera selection:

Mouse: Right-click the screen, the image will show a white frame on screen if the camera has been
selected. When in quad display mode, press the quad layout icon in layout menu to select all four cameras.

Front panel: Use the arrows to change the selection. Pressing the “right” or “left” arrow when the last/first
camera (1, 4, 9 or 16) is highlighted will select all cameras.

3.4 CHANGE AUDIO OUTPUT OPERATION

Use the arrow keys to select camera #1 and press “Enter” key to switch audio output on and off. An audio
icon will appear on the screen. Please make sure “Record Audio” option under Camera 1 Basic Settings
setup menu is ON if audio recording is required. Also, the audio source and/or audio output amplifier have
to be connected properly in order to utilize the audio functions. Note: Only Cam#1 controls audio, all others
do not control audio.

29

16

3.5 PLAYBACK

The playback bar is the fastest way to show video from the exact time which users want to see. The
playback bar allows a user to see both a time line and the current playback indicator. The user can then
click the time line to move the indicator to the position which they want to see. The operation is as follows:

To playback:

By mouse: Right-click to bring up the menu bar and click on to enter Playback Menu.

By front panel: Press

key to enter Playback Menu.

The playback bar will show (see figure below):

2009/05/25 09:09:30PM 2009/05/25 09:09:40PM 2009/05/25 09:10:30PM

14 15

1. Stop key: press to stop playback

2. Slow Reverse key: press to start slow reverse playback

3. Pause key: press to pause playback

4. Slow Forward key: press to start slow forward playback

5. Fast Reverse key: press to start fast reverse playback

6. Reverse key: press to start reverse playback

7. Forward key: press to start forward playback

8. Fast Forward key: press to start fast forward playback

9. Time bar: Move the slider on the time bar to the select time to playback (The start time and end time for

time bar appears below the bar). The status of each camera is represented by different colors on the
time bar. Green means normal; orange indicates a Motion; blue indicates Video Loss, red indicates an
alarm event.

10. “+” and “-“ signs are used to adjust the time scale range for the bar. Press “+” or “-“ to select between

scale levels L1 ~ L5. When changing level, the start time and end time of the time bar will change

L1: Entire time bar is 2 days
L2: Entire time bar is 30 hours.
L3: Entire time bar is 1 hour.

30

L4: Entire time bar is 10 minutes.
L5: Entire time bar is 1 minute.

11. Express copy: Press to start express copy when camera during playback (only one camera)

12. Playback speed indicator

13. Press “X” to close the playback bar.

14. Start time for bar (the left-most point of the time bar)

15. Current playback time (the time indicated by the slider)

16. End time for time bar (the right-most point of the time bar)

3.6 PTZ

3.6.1 General PTZ control (if PTZ cameras are installed)

Right-click to bring up the menu bar and click on to display PTZ Controls.

The following actions can be performed using the PTZ Menu:

1. Use Direction Arrows (up, down, left, right) to move the camera to the desired direction
and angle.

2. To Zoom, Click “Z+” to zoom closer or “Z-” to zoom farther away.

3. To Focus, click “F+” to focus far or click “F-” to focus near.

4. With Iris, you can increase the amount of light by clicking “I+” or decrease it by clicking “I-“.

5. To program a preset position (if supported by the camera)

a. Move PTZ camera to the specified position
b. Click “Preset” button
c. Click the number of the desired position (This will be displayed in the box)
d. Click “Set” button

6. To jump to a preset position

a. Click “Preset” button
b. Click the number of the desired position
c. Click “Go” button

7. Shortcut for presets #1-9

a. Click digit 1-9 button without clicking any other buttons
b. The camera will seek that preset position

8. Steps to delete a preset position (if supported by the camera)

a. Click “Preset” button
b. Click the number of the desired position
c. Click “Delete” button

9. For Auto Pan

a. Click “Auto Pan” button

31

10. Pattern Operation (Pattern is the “0” Tour in Everfocus and Pelco PTZ cameras)

a. Click “Pattern” button

11. Steps to run a tour

a. Click “Tour” button
b. Click the number of the desired tour
c. Click “Go” button

12. Steps to remove a tour (if supported by the camera)

a. Click “Tour” button
b. Click the number of the desired tour
c. Click “Delete” button

Click “C” to clear the digit in the number display
Click “X” at the top-right corner to hide the PTZ menu (see Express control below)
Click “Exit” to leave PTZ function.

REMEMBER:

Click “X” at the top-right corner to hide the PTZ menu (see Express control below)
Click “Exit” to leave PTZ function.

“X” only HIDES the PTZ control panel. “EXIT” closes the panel and exits PTZ mode!! Other controls will not

respond until you EXIT the PTZ mode!!

3.6.2 Express Control of PTZ

If the PTZ control panel/menu has first been opened and then hidden, the mouse can be used to control
basic PTZ functions (Quick Mouse Control). The mouse cursor will change to different icons in different
areas of the screen. With Quick Mouse Control, the user can control PTZ direction, zoom, and focus by
clicking directly on screen. The screen is divided into 16 areas, with the outer ring is divided into 12 zones
used to control movement direction. The inner square of 4 areas is used to control zoom and focus.

32

Figure 3-3 Express Control PTZ

The screen is divided into a 4x4 grid. The function of each section is defined as below:

 1: PTZ pan/tilt left and up
 2, 3: PTZ tilt up
 4: PTZ pan/tilt right and up
 5, 9: PTZ pan left
 8,12: PTZ pan right
 13: PTZ pan/tilt left and down
 14, 15: PTZ tilt down
 16: PTZ pan/tilt right and down
 6: Focus closer
 10: Focus further
 7: Zoom in
 11: Zoom out

REMEMBER:

Click “X” at the top-right corner to hide the PTZ menu (see Express control below)
Click “Exit” to leave PTZ function.

“X” only HIDES the PTZ control panel. “EXIT “ closes the panel and exits PTZ mode!! Other controls will not

respond until you EXIT the PTZ mode!!

33

3.7 LAY OUT

The ENDEAVOR264 DVR has several display modes available, depending on the number of cameras the
DVR supports. The different available layouts for a 16 camera model are shown below:

NOTE: PIP display is not available in Playback mode

To change layout, follow the steps below:

By mouse: Right-click to bring up the menu bar and click then click on the desired layout choice.

By front panel: Push the “View” button on the front of the DVR to scroll through each display format.

3.7.1 Bring a camera to full screen mode

By mouse: Double left-click on the selected channel to put that camera in full screen mode.

By front panel: Press any channel key to bring that channel to full screen mode.

With a mouse, double left-click again on the screen to return to the previous multiple camera layout.

3.8 CHANNEL SWIT CHING

Use this function to change a channel position within a multiple camera display

1. Select one camera

2. Press Channel button .

3. Click on the channel number you wish to select on the channel bar. The camera channel displayed in

that position will be switched.

EX: On a four camera screen, select camera1 and enter Channel menu and choose “2”, then camera 2 will
show on position of camera 1, camera 1 will show on position of camera 2. If the new camera being
selected is already displayed on screen, then the camera positions will be exchanged. If the new camera
being selected does not already appear, it will replace the previously displayed camera.

34

3.9 DISPLAY

Press the Display button on the menu by using the mouse or selecting this icon with the front panel
keys and pressing ‘Enter’. Pressing/clicking cycles through the four OSD formats:

1. Press to show camera information. Please see the following table for camera information icons.

Recording Playback Fast forward Fast backward

Alarm Motion Video loss Express copy Audio out

3. Press again to show status information. Please see the following table for status representation.

Back pause

Alarm Audio Event HDD failure

Motion Video loss No network

4. Press again to show both status information and camera information.

5. Press again to hide all information.

HD temp. too high

Seq.

3.10 SEQUENCE

1. By mouse: Click Sequence button to enter the auto sequential switching mode.

2. By front panel: Press the Sequence button on front panel to enter the auto sequential switching mode.

3.11 ZOOM

1. Make sure no camera is in playback mode

2. Select one camera

3. Right-click to bring up the menu bar and click button. Or, press the ZOOM button on the front

panel.

35

4. When in ZOOM mode, the mouse cursor will change to a different icon in different areas of the screen.

Or, use the arrow keys to bring a different portion of the magnified image into view. Users can control
the portion of the magnified image to be displayed by clicking directly on screen:

Figure 3-4 Zoom Express Control

The screen is divided into a 4x4 grid. The function of each section is defined as below:

 1: Left and up
 2, 3: Up
 4: Right and up
 5, 9: Left
 8,12: Right
 13: Left and down
 14, 15: Down
 16: Right and down
 6, 7, 10, 11: Not used

3.12 SEARCH

By mouse: Right-click to bring up the menu bar and click to enter Search Menu.

By front panel: Press ”Search” key to enter Search Menu directly.

36

3.12.1 Time Search

Figure 3-5 Search Menu – Time Search

Start Date/Time: Select the time to begin the search by choosing the Date and Time.

Click on the “Play” button to start the search. The DVR will automatically begin to play the video selected.
The DVR will play the nearest time if there is no data at the selected time.

In search playback mode, pressing the “Stop” button will return to the search menu.

3.12.2 Event Search

Figure 3-6 Search Menu – Event Search

37

Start Date/Time: Select starting date and time

End Date/Time: Select ending date and time.

Camera: Select which cameras to include in the search.

Event: Select which event type(s) to search for. Choose from Alarm, Motion or Video Loss. Or specify an

event by entering the event name to be searched in Text box.

Click on the “Search” button to start searching. The search results will be shown as a list of events.

Prev Page: Go to previous page

Next Page: Go to next page

Play: Playback selected item

Copy: Copy selected item

Note: Text Search supported by VSI-Pro Max POS/Cash register interface from AVE has been
implemented. For more information, you may contact AVE (

http://www.avethailand.com) directly. If you

have any other POS integration request, please contact EverFocus sales.

3.12.3 Smart Search

Smart Search allows the review of a segment of the recorded video from individual cameras to detect
motion in an area specified at the time of the search. The resulting ‘motion events’ are displayed in the form
of an Event List.

38