Digital Microphone
Quick Start Guide
20110220V01
Product introduction
Notice
Thank you for buying this product
If need after service, please take this product
to after service center and inform the reason
that causing malfunction.
Please view User’s Manual carefully before you
use product.
Please keep User’s Manual in a safe place after
reviewing.
As product performance is being improved
unceasingly, the User’s Manual would be
changed directly. There is no notice to inform you.
Electric equipment specification:
Input
DC12V 2A
1.Changes or modifications are not expressly approved
by the manufacturer could void the user's authority to
operate the equipment. Changes or modifications to
the device may void FCC and CE compliance. In
frequently used radio links should be tested regularly
to protect against undetected interference or fault.
2.Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Danger
3.Don’t modify product in any way. Otherwise, it’ll
cause a fire, electric shock, serious personal injuries
or product damaged. Only distributor or service center
can do product internal checking, maintaining and
repairing.
4.Please far away from flammable or explosive gases
when use this product, otherwise , it will result in
explosion.
5.If any form of liquid or object into the product, please
don’t use the product. Please contact distributor or
service center, and don’t continue to use this product,
otherwise, it will cause a fire or electric shock.
6.Operating this product with wet hands against,
otherwise, it will cause electric shock.
7.Don’t use this product in the flight.
1
2
Warning
Attention
1. For safety reasons, please keep the product or
accessories out of the reach of small children or
animals against accidents such as:
- swallow product and accessories. If it happens,
please go to see a doctor immediately.
- Some parts of product will result in personal injuries.
Do not place
2.
environment,, high or low temperature environment
may cause negatively affect for internal parts, even
result in a fire.
Such as: microwave oven, oven, radiator, inside or
upside of refrigerator, it may cause
overheating even explosion.
this product
under high temperature
the product
1.If the credit card is near this product, it will be
demagnetized. Please keep credit card away from this
product.
2.A malfunction of this product would be resulted in if
using the power adapter that doesn’t match with the
product.
3.Painting this product is prohibited. It will obstruct
activities of parts and affect normal use.
4.This product is electronic equipment, Badly
damaged would be caused if not prevent the
machine from a impact or rough usage.
3
4
Accessory
Please make sure below components all in accessary box.If any loss,kindly
contact the distributor.
String
Wireless Mic
USB Cable
Quick Start Guide
Collar Set Mic
Function Instruction
Audio in phone jack
MIC in phone jack
DC 5V power jack
Connecting Instruction
Wireless microphone connection
Audio cable
：
USB port
USB cable
External Mic
Volume increase
Mic/Audio switch
Volume decrease
Signal light
5
212))
ON
OFF
Power on
Power off
6
Light Signal Specification
Simple Malfunction Elimination:
Blue Light
OFF
Quick flashing
Slow flashing
Slow flashing
Slow flashing
Red Light
OFF
ON
Slow flashing
Quick flashing
Light Instruction
Power off
Matching state
Match successfully in connecting state
MIC mode if flash one time every 2.5s
Audio mode if flash two times every 2.5s
Charging, red light tuns off automatically after
charging complete
Low power and need to charge if flash one time
every 2.5s
NO signal connection between mic and speaker
Frequency Matching Procedure
1.Turn on the mic, frequency matching procedure needs 3 seconds.
2.After R/B LED quickly flashing alternately we can hear “Bi - Bi” sound.
It means we finish the frequency match process.
3.Matching distance is under 3 meter between mic and speaker.
4.Make sure the bottom of transmitter doesn’t be blocked.
1. Q: Turn on the emitter and finish matching process, the speaker
is soundless.
A: 1.Please make sure if or not matching distance is within 3
meters.
2.Please make sure if or not the emitter is power off.
3.Please make sure if or not hte speaker connects power.
2. Q: No signal light after the emitter turns on .
A: Please make sure if or not the emitter is power off.
3. Q: Low voice when use emitter.
A: Manually adjust the sound button and increase volume.
4. Q: The emitter doesn’t work when charging.
A: Please check if or not the charger is plugged and voltage
is correct.
5. Q: The emitter can’t finish matching process.
A: 1.Please make sure if or not matching distance is within 3
meters away from speaker.
2.Please make sure if or not the emitter is power off.
7
6. Q: How long the emitter can be used?
A: Complete charge process needs at least 4 hours continuous
charging and if it can be continuous used at least 8 hours,
the emitter still can be used at least 1 hours if it appears
reminding on “lack of electricity”.
8
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
z Reorient of relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
9
Loading...