Everest AP1004WRi, AP24I612 Installation Manual
EVEREST™'Network'Solutions'
Model'Number:'AP24I612'
INSTALLATION'GUIDE'
AP1004WRi'Wireless'
Access'Point'
Release'Number:'1.4'
Page | i
AP1004WRe Installation Guide
Table of Contents
Chapter 1 : Overview ............................................................................................................. 1
Dependencies ................................................................................................................................ 1
AP1004WRi Package Contents .................................................................................................. 1
Additional Item ............................................................................................................................. 1
Item Identification ....................................................................................................................... 2
Related Documentation .............................................................................................................. 2
Chapter 2 : Installing AP1004WRi ..................................................................................... 3
Third-Party Mounting System Installation ........................................................................... 3
Connecting AP 1004WRi .............................................................................................................. 5
Chapter 3 : Configuring AP1004WRi ................................................................................. 6
Logging into BaseCamp ................................................................................................................ 6
Configuring AP 1004WRi .............................................................................................................. 6
Configuring AP1004WRi to Work with Discovery Protocol ................................................ 8
Chapter 4 : AP1004WRi Coverage ...................................................................................... 9
AP1004WRi Radiation Pattern .................................................................................................. 9
Regulatory Declarations .................................................................................................. 11
Appendix: Technical Specifications .............................................................................. 16
Mechanical Specifications ........................................................................................................16
Operational Requirements .......................................................................................................16
Environmental Requirements ..................................................................................................18
Page | ii
AP1004WRe Installation Guide
Safety Warnings
The AP1004WRi Wireless Access Point installation must be performed by certified technicians only and
in compliance with all local/state/federal safety requirements. All warnings and information in this
manual should be read and understood before proceeding with installation. Any noncompliance by the
user voids the warranty of the product.
General Safety
You can be killed or injured if performing antenna installation near electrical power lines.
Carefully read and follow all instructions in this guide. Ensure that there are no high voltage or
electrical fields nearby.
Working Aloft Warning
When working on tower or roof, individuals must wear safety belts. Tools must be tied to the
individual using them. Workers below must wear safety helmets.
Lightning Activity Warning
Make sure not to connect or disconnect cables during periods of lightning activity. A surge
protective device should be installed to prevent potential damage from very high surges, for
instance, the peak surges caused by lightning.
Explosive Device Proximity Warning
Do not operate network devices close to explosive merchandise or in explosive environments,
for example, in the vicinity of a gas station.
Antenna Placement Warning
Do not install any antenna near overhead power lines or other electric light, or where the
antenna can come into contact with such circuits.
Grounding Warning
Protect your AP1004WRi Wireless Access Point by installation of grounding lines. The ground
connection must be complete before connecting power to the AP1004WRi Wireless Access
Point enclosure. The requirement of grounding is to make sure the resistance is less than
5 ohm between the ground termination point to grounding tier.
Power Installation Warning
The installation of the power switch must be performed by a certified technician. The power
switch is not supplied with the AP1004WRi Wireless Access Point. The power cord must be
assembled by a certified technician, and the final assembly must comply with related
requirements.
Solar Irradiation and High Temperature Protection
Pay attention to the level of sunlight, which can increase the working temperature of the
AP1004WRi Wireless Access Point to higher than specifications allow.
Page | 1
AP1004WRe Installation Guide
Chapter 1 : Overview
This document provides information and procedures required to install and configure the AP1004WRi
Wireless Access Point (model number AP14E612) into a WLAN installation and is intended for certified
system installers, system administrators, and network operators.
The WLAN system is designed for high density deployments. It comprises of the following main
components:
• AP1004WRi Wireless Access Point (AP)
• Access Controller (AC)
• BaseCamp™ Wireless Management System
Dependencies
The installation and configuration of AP1004WRi Wireless Access Point depends on the following
components:
• Access Controller
• BaseCamp™ Wireless Management System
• DHCP Server
AP1004WRi Package Contents
The AP1004WRi package consists of the following item:
• One AP1004WRi Wireless Access Point
The installation technician is responsible for procuring wall/ceiling anchors, mounting
screws, and safety systems, as required by the local/state/federal authorities governing the installation of the AP1004WRi Wireless Access Point.
Additional Item
The following additional item is to be purchased separately:
• Access Controller
The BaseCamp™ Wireless Management System is bundled along with the Access Controller.
Page | 2
AP1004WRe Installation Guide
Item Identification
The following figures show top and bottom view of the AP1004WRi Wireless Access Point.
Figure 1: AP1004WRi Wireless Access Point - Top View
Figure 2: AP1004WRi Wireless Access Point - Bottom View
Related Documentation
• AP1004WRe Installation Guide
• AP1004NRe Installation Guide
• AP1002We Installation Guide
• AP1002Oi Installation Guide
• Access Controller Installation Guide
• BaseCamp™ Wireless LAN Management System User Guide
• BaseCamp™ Wireless LAN Management System Quick Start Guide
Page | 3
AP1004WRe Installation Guide
Chapter 2 : Installing AP1004WRi
The AP1004WRi installation must be performed by certified technicians only and
Proper grounding and surge protectors may be required in some installations.
The installer or user assumes all liabilities unless the installation methods are explicitly
This section provides information required to install AP1004WRi Wireless Access Point.
in compliance with all local/state/federal safety requirements and building codes.
The network coverage depends on the location and position of the AP1004WRi.
Third-Party Mounting System Installation
stated in a warranty agreement between Tembo Systems, Inc. and the third-party
installer.
AP1004WRi Wireless Access Point has two sets of mounting holes at the bottom of the chassis for
attaching third-party mounting systems:
• The inner set of mounting holes are 75 mm apart in both the horizontal and vertical directions and are
tapped with a M4 x 0.7 mm thread pattern to a depth of 10 mm.
Loading...