OPERATION, MAINTENANCE
AND SAFETY INSTRUCTIONS
FOR EVERDURE HEATER HCT241S & HCT242B
HEAT LIVE RELAX
IMPORTANT SAFETY INSTRUCTIONS
2
IMPORTANT: Read the safety precautions of this booklet carefully before attempting to
assemble, install, operate or maintain the product described. Protect yourself and
others by observing all safety information. Failure to comply with instructions
could result in personal injury and/or property damage. If you are unsure about
anything regarding your heater or these instructions, please contact Everdure on
1300 766 066 before operating your appliance.
1. Read all instructions carefully before using the heater.
2. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.
3. Remove the package and ensure that the heater is undamaged. In case of doubt do not use the heater
and contact Everdure Service. Do not let children play with any parts of the package.
4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
5. Before you use the heater, check if the voltage marked on the rating label corresponds to the mains in
your home.
6. Extreme caution is necessary when the heater is used by or near children or individuals with decreased
mental and physical capacity and whenever the heater is left operating unattended.
7. Avoid using extension cords as the extension cord may overheat and cause a risk of fire.
8. Do not pull the power cord to disconnect with the power source. Always grasp the plug to pull it out.
9. Do not insert any objects into the heater as it may cause an electric shock or fire or damage to the
heater. Do not block or tamper with the heater in any manner while it is in operation. To prevent a
possible fire, do not block the air inlet or outlet in any manner. Do not place on soft surfaces, like a bed,
where openings may become blocked.
10. Do not leave the heater unattended. Always unplug the heater when not in use.
WARNING: The Main Power Switch and the On/Off switch should not be used as the sole means of
disconnecting power. Always unplug the power cord before servicing or moving the unit.
11. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use the
handle when moving the heater (where available) or hold on the sides if not available (make sure the
unit is turned off). Keep combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them at least 1 foot (0.3m) from the
sides and rear.
12. The heater has hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous
locations such as flammable, explosive, chemical-laden or wet atmospheres. This heater is intended
for general indoor domestic use ONLY.
13. This heater is not intended for use in wet or damp locations. Never locate a heater where it may fall into
a bathtub or other water container.
14. Do not use the heater outdoors.
15. This heater includes a tilt switch that turns the heater off if it falls over. Once righted, the heater can be
used as normal.
WARNING:
To avoid danger of electric shock, unplug from outlet when not in use and before cleaning. If the
supply cord is damaged, it must be replaced by a special cord or assembly available from an
authorised person. In order to avoid overheating, do not cover the heater. The heater must NOT
be located immediately below a socket outlet. Do not use the heater in the immediate
surrounding of a bath, shower or swimming pool.
HEAT LIVE RELAX
GENERAL HEATER PARTS
Front view
1. Touch sensor control panel with LED display
2. Front protective grill for air inflow
3. Base
4. PTC heating element
Back view
1. Main switch (Power on/off)
2. Handle
3. Back removable grill for the inflow of air
4. Air filter
Remote control
1. Remote control
2. Signal transmitter
TOUCH SENSOR FUNCTIONS
3
Heater on/off
Output high/Low
Oscillation
SET Setting automatic timer or temperature
+ Increase setting
- Decrease setting
Oscillation
HEAT LIVE RELAX
GETTING STARTED
1. Carefully remove the parts of the heater from the plastic bag and the carton, and unscrew the securing nut. Place
the base section on the bottom of the unit & screw on with the securing nut. Unwind the cord to its full length.
2. Place the heater onto a stable, flat and dry surface.
3. Turn the heater off (“O” on the power switch - see diagram above). Plug the cord set into a 220-240V A.C. 50Hz
electrical outlet. Turn the power on at the electrical outlet.
4. Turn the heater on (“-“ on the power switch – see diagram above). Two auditable ‘beeps’ will be heard to
indicate that power is now connected to the heater and that it is ready for operation. The display will light up
indicating the room temperature. Refer to the operating instructions section further in this manual for the full
operation of your heater.
OPERATING INSTRUCTIONS
All functions that can be performed from the main unit are repeated on the remote control. Whenever a button is
depressed on the heater or remote control, an auditable ‘beep’ is sounded. This confirms that a button has been
pressed, not that the operation has changed.
When in normal operation, the display will show the room temperature (9ºC - 39 ºC), if it is below this range, the
display will show “Lo”, or above the range, it will show “Hi”.
HEATER ON/OFF BUTTON
Press the button to start the heater. The heater will start operating at “low”. To turn the heater off, press the
button again. NOTE: When the heater is turned off, the fan will run for a short period of time to cool the fan down.
OUTPUT HIGH/LOW BUTTON
The output high/low button works only when the heater is in manual mode. The heater starts running at low (the
low indicator light is lit). Pressing the button once will change the output to high (the low indicator turns off & the
high indicator is lit). Note: the change is to the heating elements and the fan speed stays the same.
OSCILLATION BUTTON
To start the heater oscillating, press the oscillation button. To halt the oscillation in the position it is currently in,
press the button again.
HEAT LIVE RELAX
SET BUTTON
The heater can be set to run for up to 12 hours (in 1 hour increments) and then turn off. To use the timer function,
press the SET button on the heater. The display will change from the room temperature to a flashing number (the
length in time in hours). Pressing the “+” and “-“ buttons will adjust the length of time the heater will run for. To
confirm the time, stop pressing the buttons and the display will stop flashing and return to the room temperature.
After running for the set time, the heater will turn off as normal.
To cancel the function, press the heater on/off button.
The maximum room temperature is set by pressing the SET button twice. The display shows a flashing temperature,
which is adjusted by pressing the “+” and “-“ buttons. The temperature range is 15ºC to 35º. To confirm the
maximum room temperature, stop pressing the buttons and the display will stop flashing and return to the room
temperature. The heater will run until the required temperature is reached (both the low and high indicators are off),
at which point the elements will turn off but the fan will continue to work. When the room temperature drops, the
elements will turn on again.
To exit this automatic mode, press the heater on/off button.
NOTE: The maximum room temperature set also effects the operation in manual mode; if the room temperature is
greater than the set maximum room temperature, the heater will not work.
REMOTE CONTROL
All functions that can be performed from the main unit are repeated on the remote control. Please note that:
Output high/low = “heater”
SET = “shift”
Oscillation = “scanning”
The remote control requires 1 CR2032 battery which is inserted into the bottom of the control. To use the remote
control, point at the front of the heater and push the appropriate buttons.
SAFETY FEATURES
1. There are two thermal overload protectors is built in the heater to prevent overheating. The first is resettable and
the second is non-resettable.
2. When an overheat temperature is reached, the heater will automatically shut off. It can only resume operation
when the user resets the unit (see reset instructions below).
3. If the resettable thermal overload protector fails, the non-resettable thermal overload protector will activate. If
this happens, the heat will not reset. Please contact Everdure Service.
To reset your heater:
1. Unplug the heater and wait between 5-10 minutes for the unit to cool down.
2. Then, turn on the unit again and operate normally.
HEAT LIVE RELAX
CLEANING & MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING, DO NOT
IMMERSE HEATER IN WATER!
Clean the Air Inlet with the vacuum brush attachment on your Vacuum cleaner.
Clean the body of the heater with a soft damp cloth. Always make sure that the heater is completely
dry before connecting back to the mains supply.
CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc. as they will damage the
heater. NEVER use ALCOHOL OR SOLVENTS.
STORAGE: Store the heater with these instructions in the original packaging, in a cool, dry place.
WEEE WARNING
This product should not be disposed of with household waste. Please recycle where facilities exist and
check with your local authority for recycling advice.
HINTS & TIPS
Where possible your electric heater should be connected to a power outlet that uses a separate 10 amp power
circuit. This will avoid overloading your household fuse.
In the event that your household fuse is overloaded and trips, please note this is normally caused by the use of
excessive power outlets at the same time your heater is operating (for example, a steam iron, kettle, toaster etc.).
Please ensure to check the use of the power circuit and adjust when heater is in use (i.e. turn off the heater when
boiling a kettle). Should you still experience difficulty contact Everdure Service for assistance.
WARRANTY
Please refer to the separate warranty documents accompanying this product. This product has a 2 year
replacement warranty.
To make a claim on the warranty, the heater must be returned to the point of purchase together with the original
receipt. Warranty does not apply to any defect, deterioration, loss, injury or damage caused by, or as a result of
the misuse or abuse of this heater. You may have rights implied by State or Federal law. Nothing in terms of this
warranty is to be taken to exclude any conditions or warranties implied by state or Federal law, which cannot be
excluded or modified. .
We highly recommend that you register your Everdure products on www.everdure.com
.
Everdure National Sales & Service Line
1300 766 066
HEAT LIVE RELAX
OTHER PRODUCTS AVAILABLE FROM EVERDURE
Barbecues
Gas Heaters
Cooking Products
HEAT LIVE RELAX
A division of Shriro Australia Pty Ltd
23-27 Chaplin Drive Lane Cove NSW 2066
1300 766 066
www.everdure.com
IM Ref: HCT24XX 24/2009/12
HEAT LIVE RELAX
HEAT LIVE RELAX
Loading...