Everdure Ecubow, E-cubo User Manual

OPERATION, MAINTENANCE

AND SAFETY INSTRUCTIONS

FOR EVERDURE e-CUBO HEATER

THE EVOLUTION OF HEATNG

IMPORTANT SAFETY INSTRUCTIONS

2

IMPORTANT: Read the safety precautions of this booklet carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage. If you are unsure about anything regarding
your heater or these instructions, please contact Everdure on 1300 766 066 in Australia
or [phone] in New Zealand before operating your appliance.

1. Read all instructions carefully before using the heater.

2. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electrical shock, or injury to persons.

3. Remove the package and ensure that the heater is undamaged. In case of doubt do not use the heater
and contact Everdure Service. Do not let children play with any parts of the package.

4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.

5. Before you use the heater, check if the voltage marked on the rating label corresponds to the mains in
your home.

6. Extreme caution is necessary when the heater is used by or near children or individuals with decreased
mental and physical capacity and whenever the heater is left operating unattended.

7. Avoid using extension cords as the extension cord may overheat and cause a risk of fire.

8. Do not pull the power cord to disconnect with the power source. Always grasp the plug to pull it out.

9. Do not insert any objects into the heater as it may cause an electric shock or fire or damage to the
heater. Do not block or tamper with the heater in any manner while it is in operation. To prevent a
possible fire, do not block the air inlet or outlet in any manner. Do not place on soft surfaces, like a bed,
where openings may become blocked.

10. Do not leave the heater unattended. Always unplug the heater when not in use.

WARNING: The Main Power Switch and the On/Off switch should not be used as the sole means of

disconnecting power. Always unplug the power cord before servicing or moving the unit.

WARNING:

11. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use the
handle when moving the heater (where available) or hold on the sides if not available (make sure the
unit s turned off). Keep combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them at least 1 foot (0.3m) from the
sides and rear.

12. The heater has hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous
locations such as flammable, explosive, chemical-laden or wet atmospheres. This heater is intended
for general indoor domestic use ONLY.

13. This heater is not intended for use in wet or damp locations. Never locate a heater where it may fall into
a bathtub or other water container.

14. Do not use the heater outdoors.

15. This heater includes an audible alarm to warn that parts of the heater are getting excessively hot. If the
alarm sounds, immediately turn the heater off and inspect for any objects on or adjacent to the heater
that may cause high temperatures.

To avoid danger of electric shock, unplug from outlet when not in use and before cleaning. If the
supply cord is damaged, it must be replaced by a special cord or assembly available from
Everdure Service. In order to avoid overheating, do not cover the heater. The heater must NOT
be located immediately below a socket outlet. Do not use the heater in the immediate
surrounding of a bath, shower or swimming pool.

THE EVOLUTION OF HEATNG

GENERAL HEATER PARTS

LED INDICATORS (MAIN UNIT ONLY)

LCD INDICATORS (REMOTE CONTROL ONLY)

THE EVOLUTION OF HEATNG

GETTING STARTED

1. Carefully remove the heater from the plastic bag and the carton.

2. Place the heater on a stable and flat surface.

3. Set the main power switch to the ’OFF’ position (see diagram on right). Plug the cord set into a 240V~A.C.
electrical outlet. Turn the main POWER switch to the ’ON’ position. A ’beep’ sound and the red LED will come
on indicating that there is power to the unit. The heater is now ready for use. Refer to the function setting
section below for the full operation of your heater. The red LED will remain lit until the main POWER foot Switch
is turned OFF and the heater is unplugged from the electrical outlet.

ON Position
OFF Position

FUNCTION SETTING

The heater may be operated by the manual controls located on the heater (refer to the MANUAL OPERATION
section) or by your remote control (refer to the REMOTE CONTROL OPERATION section).

MANUAL OPERATION

TURN THE UNIT ON (POWER): Turn the heater ON by pressing the ‘POWER’ button; the LED of the unit will

1.

display the current ROOM temperature (appears as bright red). Upon turning the heater on, the unit will be in
the default HIGH HEAT MODE.

THE EVOLUTION OF HEATNG