Event Lighting M6B20W, M6B10RGBW User Manual

1

MULTIHEAD BEAM

M6B20W & M6B10RGBW

USER MANUAL

For safety, please read this user manual carefully before initial use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to

change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting

for any clarification or information regarding this item.

www.event-lighting.com.au

V1.1

2

Safety Instructions

WARNING

• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.

• Do not look at the light source when the device is on.

• CAUTION: This unit's housing may be hot during and after operation.

• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.

• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.

• Use a safety chain when mounting this device overhead.

• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.

• Do not operate this device if the housing, lenses, or cables appear damaged.

• Do not connect this device to a dimmer or rheostat.

• ONLY connect this device to a grounded and protected circuit.

• ONLY use the hanging bracket to carry this device.

• In case of a serious operating problem, stop using immediately.

• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Power Input & Power Linking

This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.

Fuse Replacement

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

Product Installation

This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

3

Product Appearance, LUX Chart, Dimensions

M6B20W

M6B10RGBW

4

1. Project lens

2. Head

3. Arm

4. Base

5. Display

6. Foot stand

7. Operation button

8. Handle

9. Wireless indicator

10. Mic

11. Left button

12. Battery indicator

13. Up button

14. Down button

15. Enter button

16. Right button

17. 3-pin DMX in

18. 3-pin DMX out

19. Powercon in

20. Powercon out

21. Fuse

22. Power switch

9 10

11

12

13

14

15

16

17

18

19

20 21 22

1

2
3

4

5

6

7

8

5

Menu operation

Description of icons in the menu

CONNECT

LIGHT

INFOMATION

SET

PROGRAM

Menu

Default setting shadowed. Mark with ①can be basic reloaded, ② be program reloaded, ③can be private reloaded.

CONNECT

DMX Address①

XXX

DMX address setting

Wireless①

Wireless Enabled

LIGHT

Max Temperature①

80~139℃, 80℃ (176~282℉, 176℉)

Lamp will switch off when
temperature continuously
over max temperature for
5 minutes

Lamp Adjust①

Adjust value of each
channels

INFORMATION

Time Info.

Current XXXX(Hours)
Fixture Life XXXX(Hours)

Fixture boot time
Fixture total run time

Temperature

Near Lamp Temp (depends on fixture)

Temperature Sensors

Fans Speed

Near Lamp Fan (depends on fixture)

Fan speed Sensors

Channel Value

Display value of channel

Error Message

Error channels

Fixture Model

M1S150W

Display brand and model

Software Ver

1U01 V1.0.00

Version of each IC

SET

Reset

All
Pan&Tilt
Colors
Gobos
Others

Reset all
Reset Pan&Tilt
Reset Colors
Reset Gobos
Reset Others

Movement

Pan Reverse①
Tilt Reverse①
Pan Degree①
Encoders①
Pan/Tilt Mode①

ON/OFF
ON/OFF
630°/540°
ON/OFF
Stand/Smooth

Pan Reverse
Tilt Reverse
Choose Pan Degree
Encoder wheel on/off
Choose pan/tilt mode

UI Set

Mic Sens. ③
No Signal①
Temperature. C/F①
Fans Mode①
Hibernation①
Backlight①
Flip Display①

0~99%,60%
Close/Hold/Auto/Music
Fahrenheit/Celsius
Auto / High Speed
OFF, 01M~99M，15M
02~60m 02m
ON/OFF

Sensitivity of Mic
Mode when no signal
Temperature at ℃/℉
Fans mode
Sleeping mode
Show backlight time
Display 180°reverse