Eve Audio TS107, TS108 Product Manual
EVE AUDIO PRODUCT MANUAL
TS108
TS107
JAN 2016
TS108
TS107
2
SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. DO NOT install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including ampliers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of
the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. ONLY USE attachments/accessories specied by the manufacturer.
12. USE ONLY with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tipover.
13. UNPLUG this apparatus during lightning storms or when unused for long
periods of time.
14. REFER all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
EVE Audio product manual
3
15. To reduce the risk of re or electric shock, do not expose this apparatus
to rain or moisture. The apparatus shall not be exposed to dripping or
splashing and that objects lled with liquids, such as vases, shall not be
placed on apparatus.
16. Where the MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
17. DO NOT overload wall outlets or extension cords beyond their rated
capacity as this can cause electric shock or re.
18. No naked ame sources, such as lighted candles, should be placed on the
apparatus.
19. Minimum distances around the apparatus for sucient ventilation.
20. The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table cloths, curtains, etc.
21. Correct Disposal of this product. This marking indicates that this
product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
22. The lightning ash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’ s enclosure that may be
of sucient magnitude to constitute a risk of electrical shock to persons.
23.
!
The exclamation point, within an equilateral triangle, is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product.
24.
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION
AVIS : RISQUE DE CHOC ÉLECTRIQUE – NE PAS OUVRIR.
WARNING: Do Not Open! Risk of
Electrical Shock. Voltages in this
equipment are hazardous to
life. No user-serviceable parts
inside. Refer all servicing to qualied service personnel. Place the
equipment near a main power supply outlet and make sure that you can
easily access the power breaker switch.
TS108
TS107
4
25. WARNING: This product is intended to be operated ONLY from the AC
Voltages listed on the back panel or included power supply of the product.
Operation from other voltages other than those indicated may cause
irreversible damage to the product and void the products warranty. The
use of AC Plug Adapters is cautioned because it can allow the product
to be plugged into voltages in which the product was not designed to
operate. If the product is equipped with a detachable power cord, use only
the type provided with your product or by your local distributor and/or
retailer. If you are unsure of the correct operational voltage, please contact
your local distributor and/or retailer.
EVE Audio product manual
5
TABLE OF CONTENT
1. INTRODUCTION ............................................................................6
2. QUICK START ................................................................................. 7
2.1. First Steps .............................................................................................................................7
2.2. Subwoofer Connection ...................................................................................................7
2.3. Powering On .......................................................................................................................7
3. OPERATION ...................................................................................8
3.1. First Steps .............................................................................................................................8
3.2. Operating Modes ..............................................................................................................9
3.3. Powering on/o: Standby Mode .................................................................................9
3.4. Volume Mode .....................................................................................................................9
3.5. Settings Menu ................................................................................................................. 11
3.6. Filter .................................................................................................................................... 11
3.7. Sat. Filter (only when using the XLR ins & outs) .................................................. 12
3.8. Sub Filter ........................................................................................................................... 12
3.9. Sub Phase .......................................................................................................................... 12
3.10. LED Mode .......................................................................................................................... 12
3.11. Saving Your Settings ..................................................................................................... 13
3.12. Remote Control ............................................................................................................... 13
3.13. Power Switch ................................................................................................................... 15
3.14. DIP Switches ..................................................................................................................... 15
3.15. Power Connector (IEC) ................................................................................................. 16
4. POSITIONING ..............................................................................16
4.1. Subwoofer Positioning ................................................................................................. 16
4.2. Height and Distance ..................................................................................................... 16
4.3. Stereo Setup + Subwoofer (2.1) ................................................................................ 17
4.4. Multichannel Setup (5.1) ............................................................................................. 18
4.5. Room Acoustics .............................................................................................................. 19
5. TECHNICAL SPECIFICATIONS .....................................................21
6. COMPLIANCE ...............................................................................22
7. WARRANTY ..................................................................................23
TS108
TS107
6
INTRODUCTION
1. INTRODUCTION
Thank you for your time and interest in the EVE Audio product range.
EVE Audio is a loudspeaker manufacturer based in Berlin, Germany, that
specializes in the development and design of unique studio monitors.
The use of rst-class components is our highest priority because we rmly
believe this is the only way to manufacture rst-class products.
You have chosen a TS107 or TS108 subwoofer from our ThunderStorm
series. Both modelsmake use of passive radiators instead of a bass reex
port. This allows for a lower tuning of the subwoofer and avoids the
emergence of hum, which is unavoidable when applying the bass reex
port design. The passive radiator is on the bottom side of the subwoofer.
All subwoofers of the ThunderStorm series are the ideal extension for the
two, three and four-way systems of the EVE Audio SilverCone series. They
can be easily integrated in any situation thanks to their ThunderStorm
Chassis (6,5” or 8”), PWM ampliers (100 and 150 Watt), accurate DSP
technology and IR remote control. Moreover, both TS107 and TS108 oer
additional features in order to extend the frequency response of our SC203
Master/Slave system optimally.
We wish you a lot of fun with your EVE Audio subwoofer. If you have any
questions regarding our products, do not hesitate to contact your nearest
dealer or get directly in touch with us... We will be more than happy to help
you out!
All the best from Berlin.
The EVE Audio Team
EVE Audio product manual
Powering On
7
QUICK START
2. QUICK START
If you already have experience with studio subwoofers, the Quick Start
guide ought to be more than enough to get you started.
For unexperienced users we recommend reading the whole user’s manual
in order to prevent any misuse.
2.1. First Steps
Check the package components (loudspeaker, remote control + batteries,
user’s manual, power cord).
Check the setting of the DIP Switches (O).
2.2. Subwoofer Connection
Connect the two inputs on the rear side (L In + R In) to the left and right XLR
outputs of a playback source, for instance, an audio interface. The output
level should be as low as possible.
Connect the two outputs on the rear side (L Out + R Out) to the
corresponding XLR inputs of your studio’s left and right satellites. All
output levels should be as low as possible.
In case you combine the subwoofer with our SC203 stereo Master/Slave
system, connect the signal source to the SC203 inputs and the dedicated
SC203 Sub out to the Unbalanced in on the subwoofer rear panel. While
doing this, all output levels should be as low as possible.
2.3. Powering On
Engage the Power switch on the rear side of the subwoofer to turn it on
or o.
The LEDs around the System Volume control on the front panel will light
up clockwise. If the LED on the right end is dimly lit, this indicates that the
subwoofer is in Standby mode. Press the System Volume control to turn
the subwoofer on. If you turn the System Volume control counter clockwise
until the LED on the left end lights up dimly the subwoofer will be muted.
Increase the output level on the source device until the LED ring starts to
blink, then reduce the output level a bit. The maximum operating level
for the input (i.e. the analog to digital converter) is now set optimally. To
set the desired listening volume use the System Volume control on the
subwoofer. The LED ring indicates the volume setting. If the LED ring starts
to blink, reduce the output level on the signal source.
TS108
TS107
First Steps
8
OPERATION
3. OPERATION
3.1. First Steps
Rear Connections & DIP Switches
Check the package components (loudspeaker, remote control + batteries,
user’s manual, power cord).
Check the setting of the DIP Switches (O).
Connections: there are XLR input and output connectors on the rear side
that allow the connection of balanced and unbalanced devices (signal
sources, active monitors, etc.).
• Balanced XLR pin assignment: 1= Shield, 2= hot (+), 3= cold(-).
• Unbalanced XLR pin assignment: 1+3= Shield, 2= Signal.
The rear side also oers an unbalanced RCA input connector for the
connection to the dedicated Sub out of an EVE Audio SC203 Master/Slave
system.
• RCA pin assignment: Sleeve= Shield, Tip= Signal.
Depending on the setting of the Max. Input DIP switch on the rear panel,
the maximum level of the source signal should not exceed +8 dBu or
+22dBu (see Max. Input). If the input is overloaded the LED ring will start
blinking.
Loading...