Eutech Instruments Temp 4, Temp 5, Temp6 User Manual

gyM

sy...

Instruction Manual

Temp 4/5/6

Temperature Meter Series

68X243607

Technolo

adeEa

Rev. 3 08/03

Preface

This instruction manual serves to explain the use of the Temp 4/5/6 temperature meter.

It functions in two ways: first as a step by step guide to help you operate the meter; second, it serves as a handy reference guide.

This manual is written to cover as many anticipated applications of the Temp 4/5/6 meter as possible. If there are doubts in the use of this meter, please do not hesitate to contact the nearest Eutech Instruments/ Oakton Instruments Authorised Distributor.

Eutech Instruments/ Oakton Instruments will not accept any responsibility for damage or malfunction to the meter caused by improper use of the instrument.

The information presented in this manual is subjected to change without notice as improvements are made, and does not represent a commitment on the part of Eutech Instruments Pte Ltd/ Oakton Instruments.

Eutech Instruments Pte Ltd/ Oakton Instruments

Rev. 3 08/03.

TABLE OF CONTENTS

1. INTRODUCTION 1

1.1 Introducing the economy series 1

2. GETTING STARTED 2

2.1 Description of Keypad Functions 2

2.2 Description of LCD Annunciators 2

2.3 Inserting & Removing the Rubber Boot 3

2.4 Inserting New Batteries 4

2.5 Battery Replacement 5

2.6 Connecting the Temperature Sensor 5

2.7 Switching the Meter On 6

3. CALIBRATION 7

3.1 Temperature Calibration 7

3.1.1 Temperature Calibration using Offset Adjustment 7

3.1.2 Temperature Curve Selection (Temp 5 Meter Only) 9

4. MEASUREMENT 10

4.1 Taking Measurements 10

4.2 Displaying Maximum and Minimum Readings 10

4.3 Holding a Reading 10

4.4 Releasing a Held Reading 11

4.5 Maximum and Minimum Hold Mode 11

5. DISABLE AUTO POWER-OFF FEATURE 12

6. PROBE CARE AND MAINTENANCE 13

7. TROUBLESHOOTING 13

8. SPECIFICATIONS OF TEMP SERIES 14

9. ACCESSORIES 15

10. WARRANTY & RETURN OF ITEMS 16

11. RETURN OF ITEMS 17

Instruction Manual Temp 4/5/6

1. INTRODUCTION

1.1 Introducing the economy series

Thank you for purchasing the Temp 4/5/6 meter. These microprocessor-based handheld meters are economical and easy to use. They are available in three models:

• The Temp 4 uses *YSI 400 series thermistor temperature sensor

• The Temp 5 uses 100K thermistor temperature sensor

• The Temp 6 uses PT100 ohm (Platinum) RTD temperature sensor

All Temp 4/5/6 meter series feature:

• Large LCD for clear and easy reading

• Readings in

C and oF (selectable)

• Minimum and maximum temperature display

• Minimum and maximum hold mode

• Low battery indicator

• Hold function, freezes measured reading

• User calibration - offset adjustment

• Non volatile memory backup; calibration and other information remain if

battery is disconnected

• Temp 5 meter allows user selection of most suitable temperature curve for its thermistor sensor

This instruction manual is organised for quick reference with step-by-step procedures that give you thorough review of the various features and meter operations.

Included with your meter are a temperature sensor (Temp 5 only), rubber boot, 4 alkaline “AAA” batteries, an instruction manual and a warranty card. To order other accessories, please refer to Section on Accessories for more information.

* YSI is a registered trademark of Yellow Springs Instruments.

Instruction Manual Temp 4/5/6

2. GETTING STARTED

2.1 Description of Keypad Functions

Temp 4/5/6 meters have six keys on its splash-proof keypad. These keys include ON / OFF, CAL, HOLD / ENTER, (DOWN) keys.

oC/o

F, MAX /S (UP) and MIN /T

ON/OFF: Powers meter ON or OFF. Meter directly enters measurement mode when you turn it on

CAL: Allows temperature calibration of the meter.

HOLD/ENTER: Freezes the measured reading; confirm calibration

value.

MAX/S (UP) and MIN/T (DOWN): Momentarily displays meter’s

maximum and minimum temperature; enter maximum or minimum hold mode; scroll up and down in calibration mode.

oC/o

F: Switches between oC and oF in measurement mode.

OFF

CAL

HOLD

ENTER

MAX

MIN

°C/°F

2.2 Description of LCD Annunciators

The Temp 4/5/6 meters have a large custom LCD that consists of 4-digit segments and operation annunciators for “MIN’, “MAX”, “HO” (when the HOLD function is activated) and “LO” (low battery condition).

HO LO MAX MIN

C and oF. Other indicators include

°C °F

Instruction Manual Temp 4/5/6

2.3 Inserting & Removing the Rubber Boot

1. To remove meter from rubber boot, push out from the bottom edges of meter until it is completely out of boot. Ensure that the connector of temperature sensor is not connected.

2. To insert meter into rubber boot, slide in from the top of meter before pushing the bottom edges of meter down to set it into position. Lift up the stand at the back of meter for bench top applications if necessary.

Instruction Manual Temp 4/5/6

2.4 Inserting New Batteries

The battery compartment is found at the back of instrument. To open the battery compartment, push in the direction of arrow and lift up the cover. Note the polarity of battery before inserting into position. After replacement, place cover back and press down until it locks tight.

+ 16 hidden pages