OPERATING INSTRUCTIONS
FOR MODEL 3806ZL SUITE
UNIT
TO ARM (TURN ON) YOUR SYSTEM
1. Check the red window above the arming buttons to
see that all LEDs are off This indicates that all
protection points are normal. If any LED is lit, this
indicates that a protection point is off-normal (open)
and must be restored (closed) before the suite unit can
be armed (turned on).
2. Enter your four digit user code. Press each number
button firmly until you hear a beep. If you are not sure
that you have entered the correct digits, press the
backspace button (*) four times to backspace your
entry. You may then re-enter your four digit code.
3. Press the FULL ARM button. In a moment, the
beeper will start pulsing and the red
ARMED/ALARM LED will start flashing. You now
have 30 seconds to leave your suite.
4. If you attempt to arm the suite unit with one of the
zone LEDs lit, the suite unit will beep once and
nothing more will happen. Try and close up the zone
or see ZONE BYPASS on page 4.
1
TO DISARM (TURN OFF) YOUR SYSTEM
1. When you enter your suite, the beeper will start
sounding. This is to remind you to disarm your system.
2. Enter your four digit user code. Press each number
button firmly until you hear a beep. As before in
arming, you may use the backspace button (*) to
permit re-entering the code.
3. Press the DISARM button firmly. In a moment the
beeping will stop and the ARMED/ALARM LED will
extinguish. The system is now turned off.
TO ACKNOWLEDGE AN ALARM
If an alarm occurs while you are in your suite, (e.g. the
hall door is opened while the panel is SLEEP armed),
the beeper will start sounding and the ARMED/
ALARM LED will be flashing. To turn the beeper off,
enter your four digit user code and then press the
DISARM button.
DIRECT ENTRY BUTTONS:
To the left of the number buttons, notice the buttons
labelled FIRE, PANIC and MEDICAL.
These buttons are used to summon the desired service.
2
It is not necessary to enter your user code to use these
buttons. To activate any of these buttons, firmly press
and hold the button for about three seconds. The
beeper will sound a distinctive pattern for each of the
buttons and then the ARMED/ALARM LED will
start flashing. The concierge or alarm monitoring
company (if used) will receive a text message
indicating which service you have selected and will
follow their response procedure.
OTHER KEYPAD FEATURES:
HOME ARM - allows you to remain in your suite
with part of the protection turned on. The entry/exit
door is on but interior motion sensors (if any) are not
on. Opening the door will sound the entry beeper. You
must disarm the suite unit to stop the beeper.
Enter your four digit user code followed by the
HOME button. Notice that the red ARMED/
ALARM LED will blink for approximately 30 seconds
and then remain on. During this 'silent exit time' you
may leave the suite via the entry/exit door. If the
entry/exit door is opened while the LED is on steady,
the entry beeper will start. You must disarm the suite
unit within 30 seconds (see DISARM above) to stop
the beeper or an intrusion alarm will be created. If you
wait too long and an intrusion alarm is created, disarm
the suite unit (see page 2) to stop the beeper.
3
SLEEP ARM - allows you to remain in your suite
with part of the protection turned on. The entry/exit
door is on but interior motion sensors (if any) are not
on. Opening the door will cause an immediate
intrusion alarm. You must disarm the suite unit to stop
the beeper.
Enter your four digit user code followed by the
SLEEP button. Notice that the red ARMED/ALARM
LED will come on in a moment. If the entry/exit door
is opened while the LED is on steady, an intrusion
alarm will occur immediately. You must disarm the
suite unit (see DISARM above) to stop the beeper.
DOOR CHIME - allows you to be alerted any time
the entry/exit door is opened.
To turn on the chime feature, firmly press and release
the FUNCTION button and then the number 1 button.
The suite unit will beep for two seconds. Every time
the entry/exit door is opened, the suite unit will beep
for two seconds.
To turn off the chime feature, press and release the
FUNCTION button and then the number 2 button.
ZONE BYPASS - allows you to bypass a valid zone
e.g., a window you might want left open while the
protection is turned on.
4
To bypass a zone, firmly press and release the
FUNCTION button and then the number 3 button.
The BYPASS LED (lower right front) on the suite
unit will be blinking. Firmly press the number of the
zone to be bypassed (1-4) and the blinking led will
be on steady. The zone is now bypassed. To bypass
additional zones, repeat the above procedure.
To unbypass a zone(s), disarm the suite unit (see
page 2). The bypass LED will extinguish.
USER CODES
The suite panel can be operated by five different users.
These persons are called USER 1, USER 2, USER 3,
etc. By identifying who armed and disarmed your
suite unit, this will create an audit trail which will let
you know who has been in and out of your suite. A
user must be given a four digit code. It is important
not to forget these codes.
USING THE DEFAULT CODE
When you take occupancy of your suite, a default
user code' 1010' has been assigned to user number 1.
Since all suite units in the building will be given same
code, it is essential that this code be changed to one
that you prefer. It may be your year of birth, the last
four digits of your telephone number, or any other
number from '0001' to '9999'. Users 2 thru 5 have no
5
'default' setting and must be given new codes.
Check with the property management office or
building security as to the policy for submitting your
codes to them or receiving your codes from them. The
programming of the codes into the system must be
done by management/security and may require you to
prepare a list noting the user number followed by a
four digit code. After these codes have been entered
into the system, then you may then use the codes on
your suite unit.
ZONE ASSIGNMENT TABLE
The following table may be filled out to provide a
description of the protection circuit connected to each
zone in the suite unit. When a zone is off-normal, the
corresponding LED on the suite unit will light.
ZONE
1
2
3
4
5
6
DESCRIPTION
6
EMERGENCY NUMBERS
POLICE:
FIRE DEPT:
AMBULANCE:
DOCTOR:
HOSPITAL:
OTHER:
7
Loading...