Euromaid Island Canopy ICG9BLS Installation & Operation Manual

Island Canopy
Rangehood

MODEL: ICF9BLS - 900mm (Stainless Steel)

INSTA LLATION AND OPERATION MANUAL

1800 805 300

HAPL_MC_ICF9BLS_May 2013

distributors of distributors of

SERVICE WEBSITE
www.customersupport.hapl.com.au

SERVICE TOLL FREE NUMBER

Island Canopy Installation Operation Manual

- 1 -

Dear Customer,
We thank you for choosing this quality appliance and hope you enjoy many

years of reliable service.
Please ensure this manual is re ad carefully before insta ll ation and use. Keep

this manual in a safe and accessible location should future reference be
required.

Regards

Home Appliances

CONTENTS

2 ………………………………………. Notice
2 ………………………………………. Safety Warning
3 ………………………………………. Ducted installation
5 ………………………………………. Re-cir culated installation

6 ……………………………………..... Instructions of Use

9 ...…..…………………………………. Cleaning baffle filters
9 ...…..…………………………………. Replacing carbon filters
10 .…..…………………………………. Cleaning rangehood
10 .…..…………………………………. Re placing LED lights
11 .…..…………………………………. Troubleshooting

Island Canopy Installation Operation Manual

- 2 -

NOTICE

1. Thank you for choosing our cooker hood. Please read the instruction manual
carefully before use.

2. The installation work must be undertaken by a qualified and competent fitter.

3. The manufacturer disclaims all liability for any damage or injury caused as a
result of not following instructions for installation contained in the following
text.

The cooker hood is used on 220/240v, 50Hz.

SAFETY WARNINGS

• Installation of this Island Canopy Rangehood must be carried by a qualified
and competent installer.

• The manufacturer disclaims and liability for any damage or injury caused as a
result of not following instruction of installation contained in this instruction
manual.

• This Island Canopy Rangehood is not intended for use by young children or
infirm persons without supervision.

• Young children should be supervised to ensure they do not play with this Island
Canopy Rangehood.

• To avoid possible electric shock this Island Canopy Rangehood should be
unplugged before any maintenance or cleaning is carried out.

• This Island Canopy Rangehood cannot be installed in an external
environment.

• The Grease Baffle Filters should be cleaned at least once a month to avoid
the risk of fire.

• Flambe cooking cannot be carried out under the Island Canopy Rangehood
and is not recommended for use over Barbeques.

• Ducting must be independent from any other form of ducting of other
household heating sources, for example, combustion heater ducting.

• Ducting into wall cavities is prohibited unless the cavity has been designed for
this purpose.

• Lit gas burner on cooktop should never remain uncovered or on when there is
no pan present due to the risk of fire.

• Adequate ventilation of the room is required when the cooker hood is used at
the same time as appliances burning gas or other fuels.

CAUTION: Accessible parts may become hot when used with cooking appliances.

Island Canopy Installation Operation Manual

- 3 -

INSTALLATION – Ducted installation

Note: Before installation, please ensure the area is clean to avoid suction of

the remaining debris of wood, gyprock and dust.
Ducting tube should be ≥120°, parallel or above the start point when

connected to the external wall. Alternatively, ducting should trave l in a
straight run and out through the ceiling cavity to the outside through the roof.

Warning: Ducting must not terminate (expel air) into the roof cavity as this
could cause risk of fire. The ducting MUST go to the outside atmosphere using
fire retardant type ducting.

After installation, mak e sure that the extractor is level to avoid grease
collection at one end.

1. The ceiling must be able to bea r at least 120kgs w eight, and the
thickness of the ceiling must be ≧30MM, see pic 2, drill 1*170mm
round hole in the ceiling.

2. Align up the hanging bracket, drill 12 holes in the ceiling, see pic 2,
12pcs of ST6*40mm big fl at screws will be used to fix the hanging
bracket on the ceiling, and then 8pcs of M4*10 screws and M4
nuts with gaske t will be used to connect the angle support frame
iron into the hanging bracket, see pic 1, calculate the length of
the angle support frame iron, 16pcs M4*10 bi g flat screws and M4
nut w ith gasket will be used to connect the angle support frame
iron and the other angle support frame iron (the overlap length of
angle frame iron cannot less 100MM)

3. Let the one side of the extensible pipe go outside through the hole
of 170MM, see pic 3.

4. 4pcs ST4*8 big flat screws will be used to connect the internal
chimney into the hanging bracket, then put one the external
chimney, two hooks will be used to put up the external chimney in
order to the next installation, see pic 4.

5. 4pcs ST4*8 big flat screws will be used to install the outlet, see pic 5.

6. Adjust the 4 glass screws to check whether the glass and the
cooker hood body connected well and fixed, see pic 6.

7. Hold up the hood, 16pcs M4*10 big flat screws will be used to
connect the hood body into angle iron, see pic 7.

8. Put the extensible pipe on the outlet; after ensure all the things ok,
put down the hook, take from the external chimney, all the
installation is finished, see pic8.