Island Canopy
SERVICE TOLL FREE NUMBER
1800 805 300
SERVICE WEBSITE
www.customersupport.hapl.com.au
Rangehood
MODEL: ICF9BLS - 900mm (Stainless Steel)
distributors of distributors of
HAPL_MC_ICF9BLS_May 2013
INSTA LLATION AND OPERATION MANUAL
Island Canopy Installation Oper ation Manual
Dear Customer,
We thank you for choosing this quality appliance and hope you enjoy many
years of reliable servic e.
Please ensure this manual is read carefully before installation and use. Kee p
this manual in a safe and ac cessible location should future reference be
required.
Regards
Home Appliances
CONTENTS
2 ………………………………………. Notice
2 ………………………………………. Safety Warning
3 ………………………………………. Ducted installation
5 ………………………………………. Re-c irc u lat ed installation
6 ……………………………………..... Instructions of Use
9 ...…..…………………………………. Cleaning baffle filters
9 ...…..…………………………………. Replacing carbon filters
10 .…..…………………………………. Cleaning rangehood
10 .…..…………………………………. Replacing LED lights
11 .…..…………………………………. Troubleshooting
- 1 -
Island Canopy Installation Oper ation Manual
NOTICE
1. Thank you for choosing our cooker hood. Please read the instruction manual
carefully before use.
2. The installation work must be undertaken by a qualified and competent fitter.
3. The manufacturer disclaims all liability for any damage or injury caused as a
result of not following instructions for installation contained in the following
text.
The cooker hood is used on 220/240v, 50Hz.
SAFETY WARNINGS
• Installation of this Island Canopy Rangehood must be carried by a qualified
and competent installer.
• The manufacturer disclaims and liability for any damage or injury caused as a
result of not following instruction of installation contained in this instruction
manual.
• This Island Canopy Rangehood is not intended for use by young children or
infirm persons without supervision.
• Young children should be supervised to ensure they do not play with this Island
Canopy Rangehood.
• To avoid possible electric shock this Island Canopy Rangehood should be
unplugged before any maintenance or cleaning is carried out.
• This Island Canopy Rangehood cannot be installed in an external
environment.
• The Grease Baffle Filters should be cleaned at least once a month to avoid
the risk of fire.
• Flambe cooking cannot be carried out under the Island Canopy Rangehood
and is not recommended for use over Barbeques.
• Ducting must be independent from any other form of ducting of other
household heating sources, for example, combustion heater ducting.
• Ducting into wall cavities is prohibited unless the cavity has been designed for
this purpose.
• Lit gas burner on cooktop should never remain uncovered or on when there is
no pan present due to the risk of fire.
• Adequate ventilation of the room is required when the cooker hood is used at
the same time as appliances burning gas or other fuels.
CAUTION: Accessible parts may become hot when used with cooking appliances.
- 2 -
Island Canopy Installation Oper ation Manual
INSTALLATION – Ducted installation
Note: Before installation, please ensure the area is clean to avoid suction of
the remaining debris of wood, gyprock and dust.
Ducting tube should be ≥120°, parallel or above the start point when
connected to the external wall. Alternative ly, ducting sh ould trave l in a
straight run and out through the ceiling cavity to the outside through the roof.
Warning: Ducting must not terminate (expel air) into the roof cavity as this
could cause risk of fire. The ducting MUST go to the outside atmosphere using
fire retardant type ducting.
After installation, m ak e sure that the extractor is lev el to avoid grease
collection at one end.
1. The ceiling must be able to bear a t least 120kgs weight, and the
thickness of the ceiling must be ≧30MM, see pic 2, drill 1*170mm
round hole in the ceiling.
2. Align up the hanging bracket, drill 12 holes in the ceiling, see pic 2,
12pcs of ST6*40mm big flat screws will be used to fix the hanging
bracket on the ceiling, and then 8pcs of M4*10 screws and M4
nuts w ith gas ket will be used to connect the angle support frame
iron into the hanging bracket, see pic 1, calculate the length of
the angle support frame iron, 16pcs M4*10 big fl at screws and M4
nut w ith gasket will be used to connect the angle support frame
iron and the other angle support frame iron (the overlap length of
angle frame iron cannot less 100MM)
3. Let the one side of the extensible pipe go outside through the hole
of 170MM, see pic 3.
4. 4pcs ST4*8 big flat screws will be used to connect the internal
chimney into the hanging bracket, then put one the external
chimney, two hooks will be used to put up the external chimney in
order to the next installation, see pic 4.
5. 4pcs ST4*8 big flat screws will be used to install the outlet, see pic 5.
6. Adjust the 4 glass screws to check whether the glass and the
cooker hood body connected well and fixed, see pic 6.
7. Hold up the hood, 16pcs M4*10 big flat screws will be used to
connect the hood body into angle iron, see pic 7.
8. Put the extensible pipe on the outlet; after ensure all the things ok,
put down the hook, take from the external chimney, all the
installation is finished, see pic8.
- 3 -
Island Canopy Installation Oper ation Manual
Warning: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical haza rds
- 4 -
Island Canopy Installation Oper ation Manual
INSTALLATION – Re-circulated installation
The IA150IGRK re-circulating kit will need to be purchased to
perform this type of installation. The IA150IGRK consists of the
following:
1 x CF120 carbon filter
I x piece of flexible ducting
1 x re-circulating t-piece
Installation for re-circulating uses the same procedures as those for
ducted installation with exception of the need to take the ducting
to the outside atmosphere:
1. Follow steps 1, 2 of ducted installation.
2. Connect the extensible pipe to the re-circulating t-piece. see pic
10.
3. 4pcs of ST4*8 screws will be used to fix the re-circulating t-piece to
the internal chimney. see pic 11.
4. Follow step 4, 5, 6, 7, 8 of duc ted installation.
5. Fit the carbon filter to the underside of the motor housing in the
support brackets located above the baffle filters.
- 5 -
PIC 10 PIC 11
Instructions of USE
Island Canopy Installation Oper ation Manual
LCD Touch control
1. Power on: Plug in the rangehood, switch on the powerpoint, the
LCD display will then light up, with time displaying. If there has been
no other operation within 30 seconds, the backlight will turn off.
2. “Light” touch button “ “. Press the “Light” button, the lights turn on;
press the button again, the lights turn off.
3. On position and Increasing Power touch button ” “. The motor is
provided with three positions, i.e. low, medium and high.
1. Press button once, the is displayed on the display screen,
and the motor starts operation. The is the low position
(power on position.)
2. Press button once more at the low position, the is
displayed on the display screen, and the is the medium
position.
- 6 -
Island Canopy Installation Oper ation Manual
3. Press button once more at the medium position, the
is displayed on the display screen, and the is the high
position.
4. Go on pressing button a t the high position, the is still
displayed on the display screen, and the motor works normally.
It is still at high position at this time.
4. Decreasing Power and Off position touch button “ “.
1. Press “ ” button once, the motor i s adjusted to a lower
position, and the LCD screen displays that position in the
meantime; If it is decreased continuously to the position
indicating no segments, then, this is the OFF position for the
rangehood and the motor will stop.
5. “Timer” touch button “ ”:
1. Setting the Time: In the case of neither light nor motor working,
the “Timer” button is used for setting the time.
① Long press timer button for 2-3 seconds, time segment
, and the first two hour bit segment flash, use
button for the digit increase, and use button for the
digit decrease. Namely: The variable is 01 each time it is
pressed; the hour segment is with the largest digit of 23. If it
exceeds 23, button is null and void. If it is equal to 00,
then, the button is null and void.
② Press the timer button for the 2nd time , time segment
, and the last two minute bit segment flash, use
button for the digit increase, and use key for the digit
decrease. Namely: The variable is 01 each time it is
pressed; the minute segment is with the largest digit of 59.
If it exceeds 59, button is null and void. If it is equal to 00,
then, the button is null and void.
③ Press the timer button for the 3rd time, and it is the time
setting exit and confirm key.
④ Long press timer button for 2-3 seconds under this
operation mode, and it is for the hour setting; Press it for
the 2nd time: Setting for the minute; Press it for the 3rd time:
For the time setting exit and confirm, and it will be
repeated again and again (if the 1st time pressing doesn't
- 7 -
Island Canopy Installation Oper ation Manual
exceed 2 seconds, then it can't run this operating
procedure.)
2. Setting the Off Timer: In the case of either light or motor working,
the “Timer” button is for duration time settings.
① It is provided with three kinds of time segment, and they are
5min/15min/30min/timer cancel in sequence, and the 1
st
time is 5min, the 2nd time is 15min, the 3rd time is 30min, the
4th time is timer cancel, the 5th time is 5min, and the 6th
time is 15min …., and it will be repeated again and again.
② Example: Let the setting time be 15min, the display is 00:15,
00:14, …00:1, with 0:00 displays per minute, and once “00:
00” appears, the motor position and the indicator power
supply will be cut off automatically, (the display screen
displays “24-hour system”, the output is blocked up, and
the soot machine enters standby status, and the backlight
will be put out automatically 30 seconds later.)
③ Time segment change over, 5 seconds later, it starts to
decrease gradually (example: 15min is changed over to
30min, with a delay of 5 seconds, and 00: 30 on the display
screen starts to decrease gradually).
- 8 -
Island Canopy Installation Oper ation Manual
MAINTENANCE
The cleaning of the Baffle Filters
The baffle filter is made of high-density stainless steel. Please do not use th e
corrosive detergent o n it. Keeping this filter cl ean will keep the appliance
running correctly. Please stric tly follow the guidelines below.
This procedure should be done on a monthly basis, or more depending on the
type of cooking done.
Remove filters by depressing the button which will disengage the filter
from the tab holes in the edge of the filter carriage. Ensure that the free
hand supports the filters from falling onto the cooktop under the
rangehood.
Method 1: Put the filter into 40-50oC clean water, pour on detergent,
and soak for 2-3 mins. Wear gloves and clean with a soft brush. Leave
in sink dish drainer or in the sun to ensure filters are completely dry
before refitting
Method 2: The baffle filters are suitable for cleaning within a
dishwasher, use normal programme which is normally set at around 60
degrees.
Replacing carbon filters (when installed in re-circulating mode)
Note: Carbon Filters cannot be washed and re-used, they must remov ed,
discarded and replaced to ensure they are work correctly.
This procedure should be done on a 6 monthly basis although dependant on
the type of cooking performed and may require changing more of less often.
Remove baffle filters as described in previous section.
Remove saturated carbon filter in place and discard. Replace with the
new carbon filter, model number, CF120
- 9 -
Island Canopy Installation Oper ation Manual
Cleaning rangehood
Before carrying out an y cle aning of the rangehood ensure t he po wer is
turned off at the powerpoint and unplug for safety reasons. As the
powerpoint may be in the ceiling, turn off circuit breaker that th e rangehood
is connected to at the circuit board.
A. To protect the main body from corrosion over a long period of
time, the cooker hood should be cleaned with hot water plus
non corrosive detergent every month. The rangehood should be
wiped done with a soft cloth following cleaning to remove any
excess water on the hood.
B. Please do not use abrasive cleaning products as this could
damage the surface.
C. Keep the motor and other spare parts free from water, as this will
cause damage to the appliance.
D. Before cleaning the appliance please remember to cut off
power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon filter
G. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
Replacing LED lights
Warning: The rangehood must be disconnected prior to this procedure
being carried out.
Remove the baffle filters.
Push the LED light downwards, and unplug the wiring connector.
Replace with new LED lamp.
- 10 -
Island Canopy Installation Oper ation Manual
smell from the motor
the electric diagram
entrance are not tightly sealed
valve and seal with glue
or paint
shaking
the gas top too long
machine
horizontal
Troubleshooting
Fault Cause Solution
Light on, but
motor does not
work
Light does not
work, motor does
not work
Oil leakage
The leaf blocked Get rid of the blocking
The capacitor damaged Replace capacitor
The motor jammed bearing damaged Replace motor
The internal with of motor off or a bad
Beside the above mentioned, check the following:
Light damaged Replace lights
Power cord looses Connect the wires as per
One way valve and the air ventilation
Leakage from the connection of Ushaped section and cover
Replace motor
Take down the one way
Take U-shaped section
down and seal with soap
Shake of the
body
Insufficient suction The distance between the body and
The machine
inclines
The leaf damaged and causes
The motor is not tightly hanged Lock the motor tightly
The body is not tightly hanged Fixed the body tightly
Too much ventilation from open doors
or windows
The fixing screw not tight enough Tighten the hanging
The hanging screw not tight enough Tighten the hanging
Replace the leaf
Readjust the distance
Choose a new place
and resemble the
screw and make it
screw and make it
horizontal
- 11 -
Loading...