Euroheat IN1203 Operating & Installation Instructions Manual
Operating & Installation
Instructions for the
Thermostatic
Remote Control
Wood and Gas Stoves
IN1203 Edition B January 2011
This Manual Must Always be Available to the Stove Operator
Euroheat
Natural Energy Company
© EUROHEAT DISTRIBUTORS (H.B.S) LTD. January 2011
Operating Instructions Part number IN1203 Ed. B
2
WARNING
Important Safety Information
Read this manual thoroughly prior to installing, programming or operating this remote control.
This remote control system requires three (3) AAA and four (4) AA alkaline batteries to power the transmitter
and receiver. This remote control system should only be used as described in this manual. Any other use is not
recommended and will void the warranty.
NEVER LEAVE THE TRANSMITTER HANDSET ON TOP OF THE APPLIANCE AS IT MAY DAMAGE BOTH
THE HANDSET AND THE SURFACE OF THE APPLIANCE.
NOTE
Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the transmitter
to stabilize to room temperature before accurate room temperatures are displayed. If the transmitter is activated
from a severe cold condition, allow 15 minutes for accurate temperature readings to appear on the LCD.
Installation
Turn appliance OFF and allow to cool before installing or servicing. Any modification of components will void the
warranty and may cause a fire hazard.
Important
Dip switch settings
Under no circumstances should the remote control
be used if the dip switch settings have not been
correctly set.
© EUROHEAT DISTRIBUTORS (H.B.S) LTD. January 2011
Operating Instructions Part number IN1203 Ed. B
3
Thermostatic thermostatic remote control
This hi/lo remote control system provides a safe, reliable and user-friendly remote control.
The remote can be operated in “Manual” mode by pressing the “+” button to raise the firing rate or the “-”
button to reduce the firing rate.
When the “Auto” button is pressed two temperatures are displayed. The upper one, showing the ambient
temperature, and the lower one, showing the set temperature. By pressing the “ON” and “OFF” buttons the
set temperature can be raised or lowered. In the “Auto” mode the firing rate of the stove will be increased or
lowered to achieve an ambient temperature matching that of the set temperature.
The initial movement will be made within five seconds and thereafter at fifteen minute intervals.
The unit will only instigate four consecutive movements in either direction, which will take the stove to its
maximum or minimum firing rate.
Description Qty
Transmitter (Handset) 1
Battery Alkaline AAA
(for transmitter)
3
Receiver (Assembly)
consists of:
Receiver Box
L Bracket with ON/HI OFF/LO Buttons
1
Battery Alkaline AA (for Receiver) 4
Raw Plugs 2
Velcro 1
Installation Instructions 1
Motor with leads and plug 1
Contents of Kit
Features and Specifications
Contemporary ergonomic style transmitter with large LCD display
Back lit LCD display
Battery powered transmitter and receiver
Easy access front battery door
Preprogrammed for quick installation
Low battery indication
Child proof lockout
Thermal shutdown and out of range shutdown on transmitter
Quick disconnect wiring assembly
Reset button
Carefully inspect the contents for shipment
damage. If any parts are missing or damaged,
immediately contact the dealer from whom
you purchased the kit. Do not attempt to install
any part of the kit unless all parts are in good
condition.
© EUROHEAT DISTRIBUTORS (H.B.S) LTD. January 2011
Operating Instructions Part number IN1203 Ed. B
4
Batteries
The battery compartment cover is opened by pulling the retaining catch towards the cover and then away from
the body of the handset.
+
+
Positive end inserted
last when fitting
Positive end removed
first when replacing
The batteries, three “AAA-RO3 Size 3, 1.5v” are fitted with the positive end, marked with a ” ” symbol, at the
opposite end to the spring. Always fit the batteries by inserting the negative end, marked with a “ “symbol,
against the spring first. When removing the batteries the positive end should be lifted out first.
See page 8 and 13 for
details about setting the dip
switches.
+
-
© EUROHEAT DISTRIBUTORS (H.B.S) LTD. January 2011
Operating Instructions Part number IN1203 Ed. B
5
Ensure that the batteries are fitted the correct way round as
the receiver will not work if they are incorrectly fitted.
Pull down the two latching levers gently and pull
them away from the receiver, allowing the cover to
pivot downwards and be released.
The batteries supplied with the kit are for test purposes only and will only have a limited life, new batteries
should be fitted as soon as is practical.
See page 8 and 13 for
details about setting the dip
switches.
© EUROHEAT DISTRIBUTORS (H.B.S) LTD. January 2011
Operating Instructions Part number IN1203 Ed. B
6
Clip on the manual override switch
cover plate.
Receiver plugs
Insert the plug that connects the receiver’s output to the motor with the retaining latch uppermost.
The latch will be heard to click when the plug is fully engaged.
If it becomes neccessary to remove the motor plug the latch should be
squeezed to release the locking mechanism.
Loading...