EuroFans Neptune Owner's Instruction Manual

OWNERS INSTRUCTION MANUAL

54”/137cm

Neptune

with LED

INSTALLATION

OPERATION
MAINTENANCE

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION. IF UNSURE CONSULT

A QUALIFIED ELECTRICIAN

SUITABLE FOR 230V/50 CYCLE ELECTRICAL SUPPLY

Enquiries on installing your fan please call our help line on

01959-564440

[e-mail]

IMPORTANT NOTES :

Please minimise risk of electrical shock by switching off electricity supply

at the main circuit breaker. And read the following point carefully.

1. To ensure the success of the installation be sure to read the instructions and study the
diagrams thoroughly before commencing.

2. All electrical work should only be undertaken after disconnection of the power by
removing fuses or turning off the circuit breaker to ensure all pole isolation of the
electrical supply. If you are in any doubt the services of a qualified electrician should be
sought to ensure that all work is carried out in accordance with the I.E.E. Regulations,
current good practice and other national and local electrical codes.

3. Make sure that your installation site will not allow the rotating fan blades to come into
contact with any object and that there is a minimum clearance of 150mm (6”) from the
blade tip to the wall or ceiling. Please note that the bigger this clearance is the better the
airflow from your fan will be. Ensure the blades are mounted at a minimum height of 2.3
meters (7’6”) from the floor when the fan is installed.

4. The fixing point for the fan must be able to support a weight ten times that of the net
weight of the fan. Net weights can be found on the bottom of the unit’s box. If you are
mounting the fan to a ceiling junction box, the box and it’s fixing must be able to support
the moving weight of the fan and must not twist or work loose.

5. The fan must be earthed.

6. Do not connect the fan motor to a dimmer switch. This may give an unsatisfactory
performance (motor hum) and cause damage to the motor.

7. It is not recommended that ceiling fans and gas appliances are operated in the same room
at the same time.

8. The fan must be turned off and stopped completely before reversing the fan direction. This
will prevent any damage to the motor of the unit or controller (if installed).

9. Do not insert anything into the fan blades while the fan is operating. This will damage the
blades and upset the balance of the unit causing the unit to wobble.

10. After the fan is completely installed make sure that all connections are secure
and tight to prevent any problems.

11. Because of the fan’s natural movement, some connections may loosen. Check the support
connections, brackets and blade attachments twice a year to make sure they are all
secure. If they are loose tighten with a screwdriver. ( It is not necessary to take the fan
down from the ceiling )

Note : The important safeguards and instructions given in this manual are not meant to cover
all possible conditions and situations that may occur. It must be understood that common
sense, caution and care are factors, which cannot be built into any product. These factors must
be supplied by the persons caring for and using the unit.

For installation advice, or in the unlikely event of damaged or missing parts please ring:

HELP LINE : [phone]

[e-mail]

PART LIST

20W 3000K LED

All electrical work should only be undertaken after disconnection of the power by removing
fuses or turning off the circuit breaker to ensure all pole isolation of the electrical supply.

Your fan can be installed in either of two options. It can be installed as a flush mount fan
(Picture B), i.e. it is mounted as close to the ceiling as possible. It can also be installed as a
drop rod style of fan (Picture A). In this situation the drop rod assembly is used to lower the fan
down from it’s mounting position slightly. Extension rods, ranging from 12” to 72” (your fan is
supplied with 6” Drop rod in the box), are available if you need to lower your fan further. (This is
normally the case in conservatories or rooms with very high ceilings.)

Rods can be trimmed if necessary. If trimming is required cut excess from the bottom of the rod
and re-drill a hole for the cotter pin.

Picture A

Drop Rod Style

Installing the fan

Picture B

Flush Mount Style