EUROCOM Multimedia PC V12.1.00, V12.1.00 User Manual

Page 1
V12.1.00
Page 2
Page 3
I
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©August 2012
Trademarks
Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
Page 4
II
Preface
R&TTE Directive
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux­embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov­enia.
EuP-Standby and Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode or standby mode:
Standby Mode < 2W
Off Mode < 1W
Page 5
III
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has at­tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas mo st q uality marking s are voluntary.
Page 6
IV
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the service representative or an experienc e d ra di o/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference. And
2. This device must accept any interference, including interference that may cause undesired operation of the
device.
Page 7
V
Preface
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-l ocated or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environ ment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.
Page 8
VI
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 -
240V, 50 - 60Hz, DC Output 19V, 6.3A).
This Computer’s Optical Device is a Laser Class 1 Product
Page 9
VII
Preface
Instructions for Care and Operation
The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g proc edur es for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost.
5. Take care when using peripheral devices.
Page 10
VIII
Preface
Power Safety
The computer has specific power requirements:
•When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
•Make sure the socket and any extension cord(s) you use can su pport the total current load of all the connected devices.
•Before cleaning the computer, make sure it is disconnected from any external power sup­plies.
Do not plug in the power cord if you ar e wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and discon­nected all peripherals and cables (including telephone lines and power cord).
You must also remove your battery in order to prevent accidentally turning the machine on. Before removing
the battery discon­nect the AC/DC adapter from the computer.
Page 11
IX
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.
Polymer batteries may experience a slight expansio n or swelling, however this is part of the battery’s safety mecha-
nism and is not a cause for concern.
Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-
ture environments, and do not store unused batteries for extended per iods.
See also the general battery precautionary information overleaf for further information.
Page 12
X
Preface
Battery Precautions
Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
Do not remove any batteries from the computer while it is powered on.
Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
If you do not use the battery for an extended period, then remove the battery from the computer for storage.
Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
Do not try to repair a battery pack. Refer any battery pack repa ir or replac ement to your service repre sentati ve or qual-
ified service personnel.
Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es
may explode or leak if exposed to fire, or improperly handled or discarded.
Keep the battery away from metal appliances.
Affix tape to the battery contacts before disposing of the battery.
Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Page 13
XI
Preface
Cleaning
Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
When the power cord is damaged or frayed.
If the computer has been exposed to any liquids.
If the computer does not work normally when you follow the operating instructions.
If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.
Also note the following when the cover is removed:
Hazardous moving parts.
Keep away from moving fan blades.
Page 14
XII
Preface
Ergonomics
We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer:
The top third of the LCD (screen) should be at eye-level or slightly below.
The LCD should be at least 18"/45cm. directly in front of you.
If the screen resolution makes you strain to read, then adjust the resolution to something more co mfortable (see “Video
Features” on page 1 - 18).
Angle the LCD (see “Tilting the LCD Screen” on page 1 - 6) so that it doesn’t reflect any light into your eyes.
Use a chair which offers good back support (especially lower-back). The seat should allow your feet to rest flat on the
floor or on a footrest directly in front of you.
If possible, illuminate your work area with natural daylight or use a steady-glowing (non-flickering) light source.
Place the keyboard and mouse so that your arms are at your sides and your forearms are roughly parallel to the floor.
Your wrists should flex slightly downward as you work. Your neck and shoulders should also be relaxed.
Take a break from the computer. Get up, stretch, flex your wrists, walk about, and look at something else for about 10
minutes every hour.
Page 15
XIII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflecti ons from overhead lighting or outside sources of light.
Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
Position the display directly in front of you at a comfortable viewing distance.
Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
Rotate desktop background images every few days.
Turn the monitor off when the system is not in use.
Carrying the Computer
We strongly recommend using both hands to move the computer (one hand gripping the handle area and the other grip­ping the computer) to avoid accidentally dropping it. Be careful that objects such as belt buckles etc. do not scratch the screen while it is being carried.
Page 16
XIV
Preface
Wall Mounting Information
The computer may be mounted on a wall for display. The system meets VESA MIS-D Standard (100mm * 100mm) for wall mounting. However if you intend to wall mount the system please contact your service center for information in order to avoid personal injury, or damage to the computer.
Page 17
XV
Preface
Contents
Notice .............................................................................................................................................................I
EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II
FCC Statement ............................................................................................................................................IV
FCC RF Radiation Exposure Statement: .....................................................................................................V
Instructions for Care and Operation ......................................................................................................... VII
Power Safety ............................................................................................................................................VIII
Polymer Battery Precautions ......................................................................................................................IX
Battery Precautions ......................................................................................................................................X
Cleaning ......................................................................................................................................................XI
Servicing .....................................................................................................................................................XI
Ergonomics ............................................................................................................................................... XII
Wall Mounting Information .....................................................................................................................XIV
Quick Start Guide
Overview ....................................................................................................................................................1-1
Advanced Users .........................................................................................................................................1-2
Beginners and Not-So-Advanced Users ....................................................................................................1-2
Warning Boxes ..........................................................................................................................................1-2
Not Included ..............................................................................................................................................1-3
System Startup ...........................................................................................................................................1-4
System Map: Front View ...........................................................................................................................1-5
Page 18
XVI
Preface
Tilting the LCD Screen ..............................................................................................................................1-6
Buttons & LED Indicators .........................................................................................................................1-8
On Screen Display Indicators/Buttons .......................................................................................................1-9
System Map: Left View ...........................................................................................................................1-10
HDMI-In Port ..........................................................................................................................................1-11
Mode Toggle ............................................................................................................................................1-11
System Map: Right View .........................................................................................................................1-13
System Map: Rear View ..........................................................................................................................1-14
Optional Keyboard & Mouse Kit ............................................................................................................1-15
Wireless Keyboard & Mouse USB Transceiver ......................................................................................1-16
Windows 7 Start Menu & Control Panel .................................................................................................1-17
Video Features .........................................................................................................................................1-18
Power Options .........................................................................................................................................1-20
Features & Components
Overview ....................................................................................................................................................2-1
Hard Disk Drive .........................................................................................................................................2-2
Optical (CD/DVD) Device ........................................................................................................................2-3
Loading Discs ............................................................................................................................................2-3
Handling CDs or DVDs .............................................................................................................................2-4
DVD Regional Codes ................................................................................................................................2-5
Multi-in-1 Card Reader ..............................................................................................................................2-6
Page 19
XVII
Preface
ExpressCard Slot .......................................................................................................................................2-7
Inserting and Removing ExpressCards ......................................................................................................2-7
Audio Features ...........................................................................................................................................2-8
Setup for Audio Recording ........................................................................................................................2-9
Power Management
Overview ....................................................................................................................................................3-1
The Power Sources ....................................................................................................................................3-2
AC/DC Adapter .........................................................................................................................................3-2
Battery ........................................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Power Plans ...............................................................................................................................................3-4
Power-Saving States ..................................................................................................................................3-6
Sleep ..........................................................................................................................................................3-6
Hibernate ....................................................................................................................................................3-7
Shut down ..................................................................................................................................................3-7
Configuring the Power Buttons .................................................................................................................3-8
Resuming Operation ..................................................................................................................................3-9
Energy Star Power Saving .......................................................................................................................3-10
Battery Information .................................................................................................................................3-11
Conserving Battery Power .......................................................................................................................3-12
Battery Life ..............................................................................................................................................3-13
Page 20
XVIII
Preface
New Battery .............................................................................................................................................3-13
Recharging the Battery with the AC/DC Adapter ...................................................................................3-13
Proper handling of the Battery Pack ........................................................................................................3-14
Battery FAQ .............................................................................................................................................3-15
Drivers & Utilities
What to Install ............................................................................................................................................4-1
Driver Installation ......................................................................................................................................4-2
Updating/Reinstalling Individual Drivers ..................................................................................................4-4
User Account Control ................................................................................................................................4-5
Windows Security Message .......................................................................................................................4-5
New Hardware Found ................................................................................................................................4-5
Driver Installation Procedure .....................................................................................................................4-6
Chipset .......................................................................................................................................................4-6
Video ..........................................................................................................................................................4-6
LAN ...........................................................................................................................................................4-6
ExpressCard/Card Reader ..........................................................................................................................4-6
Hotkey AP .................................................................................................................................................4-6
USB 3.0 ......................................................................................................................................................4-7
MEI Driver .................................................................................................................................................4-7
Audio .........................................................................................................................................................4-7
Windows Experience Index .......................................................................................................................4-8
Page 21
XIX
Preface
Optional Drivers ........................................................................................................................................4-9
BIOS Utilities
Overview ....................................................................................................................................................5-1
The Setup Utility ........................................................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
Fatal Errors ................................................................................................................................................5-3
Non-Fatal Errors ........................................................................................................................................5-3
Setup Screens .............................................................................................................................................5-4
Main Menu .................................................................................................................................................5-5
System Time & Date (Main Menu) ...........................................................................................................5-5
SATA Port # (Main Menu) ........................................................................................................................5-6
System/Extended Memory: (Main Menu) .................................................................................................5-6
MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6
Advanced Menu .........................................................................................................................................5-7
Advanced Chipset Control (Advanced Menu) ..........................................................................................5-7
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-8
Total Graphics Memory (Advanced Menu > Advanced Chipset Control) ................................................5-8
SATA Mode Selection (Advanced Menu) ................................................................................................5-8
Boot Logo (Advanced Menu) ....................................................................................................................5-9
Power On Boot Beep (Advanced Menu) ...................................................................................................5-9
Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9
Page 22
XX
Preface
Super IO Configuration (Advanced Menu) ...............................................................................................5-9
Security Menu ..........................................................................................................................................5-10
Password on boot (Security Menu) ..........................................................................................................5-10
Set Supervisor Password (Security Menu) ..............................................................................................5-11
Set User Password (Security Menu) ........................................................................................................5-11
Interface Items (Security Menu) ..............................................................................................................5-11
Secure Boot (Advanced Menu) ...............................................................................................................5-12
Configuration (Security Menu) ................................................................................................................5-12
Boot Menu ...............................................................................................................................................5-13
Fast Boot / UEFI Boot (Boot Menu) .......................................................................................................5-14
Boot Option Priorities (Boot Menu) ........................................................................................................5-14
Wake-up On LAN (Boot Menu) ..............................................................................................................5-14
Exit Menu ................................................................................................................................................5-15
Upgrading The Computer
Overview ....................................................................................................................................................6-1
When Not to Upgrade ................................................................................................................................6-2
Removing the Battery ................................................................................................................................6-3
Inserting the Battery ..................................................................................................................................6-5
Removing the Rear Component Cover ......................................................................................................6-6
Inserting the Rear Cover ............................................................................................................................6-8
Upgrading the Hard Disk Drive/SSD ........................................................................................................6-9
Page 23
XXI
Preface
Removing the 3.5" (88.9mm) HDD .........................................................................................................6-10
Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD ...............................................................6-12
Removing the 2.5" (63.5mm) HDD or SSD ............................................................................................6-14
Upgrading the Optical (CD/DVD) Device Drive ....................................................................................6-17
Upgrading the System Memory (RAM) ..................................................................................................6-18
Upgrading the Processor ..........................................................................................................................6-21
Modules & Options
Overview ....................................................................................................................................................7-1
PC Camera Module ....................................................................................................................................7-2
PC Camera Driver Installation ...................................................................................................................7-3
PC Camera Audio Setup ............................................................................................................................7-4
Wireless LAN Module .............................................................................................................................7-10
3rd Party 802.11b/g/n Driver Installation (for WLAN Module Only) ....................................................7-11
3rd Party 802.11b/g/n Driver Installation (for Combo Modules) ............................................................7-12
Intel® WLAN Driver Installation ............................................................................................................7-13
Connecting to a Wireless Network in Windows 7 ...................................................................................7-16
Connecting to a Wireless Network Using Intel® PROSet Wireless .......................................................7-19
Intel® My WiFi Configuration ................................................................................................................7-21
Windows Mobility Center .......................................................................................................................7-30
Intel® Wireless Display Application .......................................................................................................7-31
Intel® WiDi Application Installation ......................................................................................................7-32
Page 24
XXII
Preface
Intel® Wireless Music Driver Installation ...............................................................................................7-32
Intel® WiDi Application Configuration ..................................................................................................7-33
Bluetooth & WLAN Combo Module ......................................................................................................7-36
3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-37
Intel Bluetooth Combo Driver Installation ..............................................................................................7-38
Standard Bluetooth Configuration in Windows 7 ...................................................................................7-39
Trusted Platform (Security) Module ........................................................................................................7-43
Enabling & Activating TPM ....................................................................................................................7-44
Trusted Platform Module (TPM) Driver Installation ..............................................................................7-46
Initializing TPM .......................................................................................................................................7-47
Infineon Security Platform Settings Tool ................................................................................................7-49
Troubleshooting
Overview ....................................................................................................................................................8-1
Basic Hints and Tips ..................................................................................................................................8-2
Backup and General Maintenance .............................................................................................................8-3
Viruses .......................................................................................................................................................8-4
Upgrading and Adding New Hardware/Software ......................................................................................8-5
Problems & Possible Solutions ..................................................................................................................8-7
Bluetooth Connection Problems ..............................................................................................................8-11
Interface (Ports & Jacks)
Overview ...................................................................................................................................................A-1
Page 25
XXIII
Preface
Computer Ports and Jacks .........................................................................................................................A-2
Card Reader Port .......................................................................................................................................A-2
DC-In Jack ................................................................................................................................................A-2
HDMI-In Port ...........................................................................................................................................A-2
HDMI-Out Port .........................................................................................................................................A-2
Headphone-Out Jack .................................................................................................................................A-2
Microphone-In Jack ..................................................................................................................................A-3
PS/2 Type Keyboard & Mouse Ports ........................................................................................................A-3
RJ-45 LAN Jack .......................................................................................................................................A-3
RS-232 COM/Serial Ports ........................................................................................................................A-3
Security Lock Slot ....................................................................................................................................A-4
USB 2.0/1.1 Ports .....................................................................................................................................A-4
USB 3.0 Port .............................................................................................................................................A-4
Intel Video Driver Controls
Intel Video Driver Installation ..................................................................................................................B-1
Video .........................................................................................................................................................B-1
Dynamic Video Memory Technology ......................................................................................................B-1
Intel® Graphics & Media Control Panel ..................................................................................................B-2
Display Devices & Options ......................................................................................................................B-4
Attaching Other Displays .........................................................................................................................B-5
Configuring an External Display in Windows 7 .......................................................................................B-7
Page 26
XXIV
Preface
HDMI Audio Configuration ...................................................................................................................B-10
Processor ...................................................................................................................................................C-2
Core Logic ................................................................................................................................................C-2
Display ......................................................................................................................................................C-2
Memory .....................................................................................................................................................C-2
Video Adapter ...........................................................................................................................................C-3
BIOS .........................................................................................................................................................C-3
Storage ......................................................................................................................................................C-3
Audio ........................................................................................................................................................C-3
Keyboard & Pointing Device ....................................................................................................................C-3
Interface ....................................................................................................................................................C-3
Card Reader ..............................................................................................................................................C-3
Slots ..........................................................................................................................................................C-3
Communication .........................................................................................................................................C-3
Power Management ..................................................................................................................................C-4
Power ........................................................................................................................................................C-4
Security .....................................................................................................................................................C-4
Operating System ......................................................................................................................................C-4
Design Features ........................................................................................................................................C-4
LED Indicators ..........................................................................................................................................C-4
Environmental Spec ..................................................................................................................................C-4
Physical Dimensions & Weight ................................................................................................................C-4
Page 27
Overview 1 - 1
Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer.
Chapter 3 The computer’s power saving options.
Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
Chapter 6 Instructions for upgrading your computer.
Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo and
Trusted Platform (Security) modules (some of which may be optional depending on your pur­chase configuration).
Chapter 8 A troubleshooting guide.
Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
Appendix B Information on the Intel video driver controls.
Appendix C The computer’s specification.
Page 28
1 - 2 Overview
Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Page 29
Overview 1 - 3
Quick Start Guide
1
Not Included
Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4 - 3. You will be unable to use most advanced controls until the necessary drivers and util­ities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Computer Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com­puter to communicate with external devices, connect to the internet etc.
Page 30
1 - 4 System Startup
Quick Start Guide
1
System Startup
1. Remove all packing materials, CDs/DVDs and floppy disks etc.
2. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse etc.)
3. Attach the AC/DC adapter to the DC-In jack at the rear of the LCD, then plug the AC power cord into an outlet,
and connect the AC power cord to the AC/DC adapter.
4. Push the power button at the front of the computer (along the bottom of the LCD) to turn the computer “on”.
Figure 1 - 1 - AC/DC Adapter Plugged-In/Power Button
Power Button (located along the bottom of the LCD)
Shutdown
Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.
Page 31
System Map: Front View 1 - 5
Quick Start Guide
1
System Map: Front View
Figure 1 - 2 - Front View
1. Optional Built-In PC Camera
2. PC Camera LED
3. Built-In Microphone
4. LCD
5. Power Button
6. Function Buttons
7. Power & System Activity LED Indicators
8. Speakers
1
2
5
4
6
3
7
88
5
67
Page 32
1 - 6 Tilting the LCD Screen
Quick Start Guide
1
Tilting the LCD Screen
It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc.
1. Place one hand at the top of the computer , and use the other to open the stand to an angle of around 15 degrees from the vertical position (the stand will allow you to adjust to the appropriate angle if you pull it
out and let it spring back).
Figure 1 - 3 - Adjust the Stand
1
2
Moving the Computer
We strongly recommend using both hands to move the computer. You can use one hand to grip the computer by the stand, and the other to hold the top of the LCD screen.
It is recommended that you carry the computer with the LCD facing your body to avoid scratching the surface against other objects. However take care not to scratch the LCD with any personal items, belt fit­tings or jewelry etc.(one hand gripping the stand and the other gripping the top of the computer to avoid accidentally dropping it).
15°
Adjust the stand to tilt the computer to 15° from the vertical posi­tion.
1
2
Page 33
Tilting the LCD Screen 1 - 7
Quick Start Guide
1
2. Apply pressure with one hand at the to p (at point ) of the computer (while holding on to the side with the ot her hand) to carefully push the LCD screen down in order to tilt it to the appropriate viewing angle (up to 50 degrees from the vertical position).
3. Use one hand at the top of the co mputer (while holding on to the side with the other hand) to move the compu ter back to the original position.
Figure 1 - 4 - LCD Screen Tilt
3
3
Apply pressure from the top of the screen to adjust the stand outwards (up to 50° from the vertical position).
DVD Operation
Note that although the comput­er may be tilted up to an angle of 50 degrees from the vertical position, the DVD-ROM drive will only work (i.e continue to spin and read DVDs) up until an angle of around 35 degrees from the vertical position.
If you have any problems with the system reading DVDs, ad­just the tilt angle accordingly.
50°
50°
Page 34
1 - 8 Buttons & LED Indicators
Quick Start Guide
1
Buttons & LED Indicators
The buttons located under the front panel icons allow you to make screen and input adjustments.
Figure 1 - 5 - Front Icons
Table 1 - 1 - Function Buttons
The LED indicators on the computer display helpful information about the current status of the computer.
Table 1 - 2 - LED Indicators
Icon Description
Decrease/Increase Buttons - Use the buttons
to decrease/increase the brightness/volume
Menu Toggle - Use this button to switch
between the brightness or audio menus and
use the buttons above to adjust
Mode Toggle - Use this button to toggle
between the computer and HDMI Input
modes (see “Mode Toggle” on page 1 - 11)
Icon Color Description
Orange AC/DC Power is Plugged In
Green The Computer is On
Blinking Green The Computer is in Sleep Mode
Orange The Battery is Charging
Blinking
Orange
The Battery has Reached
Critically Low Power Status
Blank The Battery is Fully Charged
Green
HDMI Cable Plugged-In (if the
computer is off - see page 1 - 11
Green System Activity
Green
The (optional) WLAN Module is
Powered On
Orange
The (optional) Bluetooth Module
is Powered On
Page 35
Quick Start Guide
On Screen Display Indicators/Buttons 1 - 9
1
On Screen Display Indicators/Buttons
Press the function menu button for about two seconds (see Table 1 - 1, on page 1 - 8) to bring up the On Screen Display. The OSD provides visual indicators for brightness, volume, camera power toggle and WLAN/ Bluetooth power toggle (the camera, WLAN and Bluetooth power indicators will only display if the modules are included in your purchase configuration) when the Hotkey AP is installed (see page 4 - 6).
Table 1 - 3 - On Screen Display Indicators
The indicators will appear when the computer boots up, or resumes from a power saving state, in order to display the current power status of the camera and/or WLAN/Bluetooth module. If you adjust the brightness or volume the OSD indicators will appear, and will also allow you to adjust the power status of the camera and/or WLAN/ Bluetooth module using the mouse to click on the icon.
OSD Icon Description OSD Icon Description
Volume Decrease/Increase Camera Power Toggle
Brightness Decrease/Increase Bluetooth Power Toggle
WLAN Power Toggle
Page 36
Quick Start Guide
1 - 10 System Map: Left View
1
System Map: Left View
Figure 1 - 6
Left View
1. Stand
2. Multi-in-1 Card Reader
3. ExpressCard Slot (see page 2 - 7)
4. 2 * USB 3.0 Ports
5. HDMI-in Port
6. HDMI-Out Port
ExpressCard Slot
The ExpressCard Slot accepts either Express-
Card/34 or Express­Card/54 formats.
1
HDMI-In Port
Note that the HDMI-In Port supports video and audio signals from attached HDMI devices.
Multi-in-1 Card Reader
The card reader allows you to use the most
popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC /
SDXC Compatible
MS (Memory Stick) / MS Pro / MS Duo
USB 3.0 Port
The USB 3.0 port is denoted by its blue col­or; USB 2.0 ports are colored black. Note that the USB 3.0 port requires a driver in- stallation (see “USB 3.0” on page 4 - 7), does not support wake on USB and is not operational under DOS.
2
3
4
5
6
4
Page 37
HDMI-In Port 1 - 11
Quick Start Guide
1
HDMI-In Port
This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen.
The computer itself does not need to be powered on to display video and audio from external HDMI input sources. As long as the computer is plugged-in to a power source using the AC/DC adapter (the HDMI-In port
will nit function under battery power), simply plug-in the HDMI cable from the external device to the computer’s HDMI-In port and the computer will act as the display device. For resolutions supported see page C - 3.
Mode Toggle
Press and hold the mode toggle button to switch between the computer and HDMI input modes. When the HDMI input source is displayed you can use any HDMI device plugged in to the computer’s HDMI-In port. A quick press of the button will toggle the display on/off.
When the HDMI cable is plugged-in, and the computer is powered off, the
icon will be green when
you press and hold the mode toggle button . When the HDMI device is playing the icon will then return to indicate the battery charge status. See Table 1 - 4, on page 1 - 12 for details.
Page 38
1 - 12 HDMI-In Port
Quick Start Guide
1
The following table indicates the functions when an HDMI cable is plugged in to the HDMI-In port.
Table 1 - 4 - Mode Toggle Functions when HDMI Cable is Plugged-In
Computer Power
Status
HDMI Icon
Mode Toggle Button
(Press & Hold)
Mode Toggle Button
(Quick Press)
The computer is
powered on (using the
AC/DC adapter)
Indicates battery charge status
only
Toggles between computer
display and HDMI input
Toggles the display on/off
The computer is
powered off (but is
plugged in to the AC/DC
adapter)
Green (when HDMI cable is
plugged-in and the Mode Toggle
Button has been pressed and
held to select HDMI input)
When the HDMI source is playing
the icon will indicate battery
charge status only
Toggles between computer
display and HDMI input
Toggles the display on/off
Page 39
System Map: Right View 1 - 13
Quick Start Guide
1
System Map: Right View
4
2
3
1
2 3
4
4
5
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unex­pected power interruption) you may push the end of a straight­ened paper clip into the emer­gency eject hole. Do not use a sharpened pencil or similar ob­ject that may break and become lodged in the hole.
Figure 1 - 7 - Right View
1. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3
2. Headphone-Out Jack
3. Microphone-In Jack
4. USB 2.0 Port
5. Stand
Changing DVD Regional Codes
Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM de-
vice to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. You can select your module’s region code 5 times (see “DVD Region
Note” on page 2 - 5).
Media Warning
Don’t try to remove the CD/DVD while the system is accessing it. This may cause the system to “crash”.
Page 40
1 - 14 System Map: Rear View
Quick Start Guide
1
System Map: Rear View
Figure 1 - 8
Rear View
1. Rear Component Cover
2. Stand
3. Vent/Fan Intake
4. Carrying Handle Area
5. USB Wireless Transceiver Cover (for Optional RF Keyboard & Mouse Kit)
6. Security Lock Slot
7. Battery
8. 2 * RS-232 Serial Ports
9. PS/2 Port (keyboard)
10.PS/2 Port (mouse)
11.DC-In Jack
12.2 * USB Ports
13.RJ-45 LAN Port
1
2
3
8
3
8
9
4
13
5
5
5
12
USB Port for
Wireless
Transceiver
Note that the USB port for the wireless transceiver is de­signed specifically for the optional RF Key­board & Mouse kit supplied with this model only.
Do not use any other USB devices in this port.
6
11
7
10
Page 41
Optional Keyboard & Mouse Kit 1 - 15
Quick Start Guide
1
Optional Keyboard & Mouse Kit
There is an optional RF wireless USB keyboard and mouse kit available for this computer series. A USB port located at the bottom of the rear cover (see “System Map: Rear View” on page 1 - 14) is designed to house the transceiver for the USB wireless keyboard & mouse kit. See “Wireless Keyboard & Mouse USB Transceiver”
on page 1 - 16 for more information.
Figure 1 - 9 - Optional Wireless Keyboard & Mouse Kit
Dongle & USB Ports
A single USB dongle (which acts as a trans­ceiver for the keyboard and mouse) is pro­vided with the keyboard and mouse kit. This dongle may be inserted into any of the USB ports however it is recommended that you use the USB port specifically provided for this (see page 1 - 14).
Port Warning
The computer can only accept one key­board at a time. Don’t try to install a USB and a PS/2 keyboard at the same time. Do­ing so may cause resource conflicts and make the system unstable.
Page 42
1 - 16 Wireless Keyboard & Mouse USB Transceiver
Quick Start Guide
1
Wireless Keyboard & Mouse USB Transceiver
If your purchase includes the optional wireless keyboard & mouse kit you can use the USB port located at the bottom left of the rear cover to house the USB transceiver (do not use this port for any other device, see sidebar).
1.Remove the USB transceiver port cover by sliding it in the direction of a rrow .
2.Insert the USB transceiver into the USB port.
3.Replace the cover.
USB Port for
Wireless
Transceiver
Note that the USB port for the wireless trans­ceiver is designed spe­cifically for the optional RF keyboard and mouse kit supplied with this model only.
Do not use any other USB devices in this port.
Figure 1 - 10
USB Port for
Wireless Keyboard
& Mouse Kit
123
1
2
1
3
Page 43
Windows 7 Start Menu & Control Panel 1 - 17
Quick Start Guide
1
Windows 7 Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac­cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.
Figure 1 - 11 - Start Menu & Control Panel
Click here to toggle Category View
Page 44
1 - 18 Video Features
Quick Start Guide
1
Video Features
You can configure display options from the Display (Control Panel) and Screen Resolution in Windows. For more detailed video information see Chapter B“Intel Video Driver Controls” from page B - 1.
To access Display (Control Panel) and Screen Resolution in Windows:
1. Click Start and click Control Panel.
2. Click Display (icon) - In the Appearance and Personalization category.
3. Click Adjust Screen Resolution/Adjust resolution.
Figure 1 - 12 - Screen Resolution
1
3
2
Right-Click Desktop
1. You can right-click the desktop and select Screen resolution (Figure 1 - 12).
2. Use the dropbox to select the screen Resolution
(Figure 1 - 12).
3. Click Advanced settings
(Figure 1 - 12) to bring up the Advanced properties tabs.
123
Page 45
Video Features 1 - 19
Quick Start Guide
1
To access the Intel(R) Graphics Media Accelerator Driver for mobile control panel:
1. Click Advanced settings (Figure 1 - 12 on page 1 - 18) in the Screen Resolution control panel in Win­dows.
2. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 13 on page 1 - 19) .
OR
3. Right-click the desktop and select Graphics Properties from the menu.
OR
4. Click the icon in the taskbar and select Graphics Properties from the menu.
Figure 1 - 13 - Intel GMA Driver for Mobile Control Panel
3
4
4
Page 46
1 - 20 Power Options
Quick Start Guide
1
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 17 ) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further con­figuration options.
Figure 1 - 14 - Power Options
Page 47
Features & Components
Overview 2 - 1
2
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components of the computer:
•Hard Disk Drive
Optical (CD/DVD) Device
Multi-in-1 Card Reader
ExpressCard Slot
Audio Features
Page 48
Features & Components
2 - 2 Hard Disk Drive
2
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" or 3.5" (pictured below) serial (SATA) hard disk drives with a height of 9.5 mm.
The hard disk is accessible from the rear of your computer as seen below. For further details see “Upgrading the Hard Disk Drive/SSD” on page 6 - 9.
Power Safety
Before attempting to ac­cess any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the ma­chine is turned off. Also ensure that all peripher­al cables, including phone lines, are discon­nected from the comput­er.
Figure 2 - 1
Hard Disk Location
Hard Disk
Page 49
Features & Components
Optical (CD/DVD) Device 2 - 3
2
Optical (CD/DVD) Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with la­bel-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/ DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly inter­rupted, insert an object such as a straightened paper clip into the emergency eject hole to open the tray.
Sound Volume
Adjustment
How high the sound vol­ume can be set depends on the setting of the vol­ume control within Win- dows. Click the Volume icon on the taskbar to check the setting (see
“Audio Features” on page 2 - 8).
Figure 2 - 2
Optical Device
1
2
3
123
Page 50
Features & Components
2 - 4 Optical (CD/DVD) Device
2
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Note the following:
Hold the CD or DVD by the edges; do not touch the surface of the disc.
Use a clean, soft, dry cloth to remove dust or fingerprints.
Do not write on the surface with a pen.
Do not attach paper or other materials to the surface of the disc.
Do not store or place the CD or DVD in high-temperature areas.
Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
Do not bend the CD or DVD.
Do not drop or subject the CD or DVD to shock.
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharp­ened pencil or similar object that may break and become lodged in the hole.
Disk Eject Warning
Don’t try to remove a CD/DVD while the sys­tem is accessing it. This may cause the system to “crash”.
Page 51
Features & Components
Optical (CD/DVD) Device 2 - 5
2
DVD Regional Codes
To change the DVD regional codes:
1. Go to the Control Panel
2. Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control p anel to allow yo u to adjust the regional code.
DVD Region Note
DVD region detection is device dependent, not OS-dependent. You can select your module’s re­gion code 5 times. The fifth selection is perma­nent. This cannot be al­tered even if you change your operating system or you use the module in another computer.
Figure 2 - 3
DVD Region Codes
Region 1 - USA & Canada
Region 2 - Western Europe, Japan,
South Africa, Middle East & Egypt
Region 3 - South-East Asia, Taiwan,
South Korea, The Philippines, Indo­nesia, Hong Kong
Region 4 - South & Central Amer-
ica, Mexico, Australia, New Zealand
Region 5 - N Korea, Russia, Eastern
Europe, India & Most of Africa
Region 6 - China
Page 52
Features & Components
2 - 6 Multi-in-1 Card Reader
2
Multi-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 6).
Card Reader Cover
Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust get­ting in to the card read­er.
Figure 2 - 4
Front View
1. Card Reader
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS (Memory Stick) / MS Pro / MS Duo
1
Page 53
Features & Components
ExpressCard Slot 2 - 7
2
ExpressCard Slot
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).
ExpressCard/54 is used for applications which re­quire a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the Express­Card/34. Make sure you install the Card Reader driv­er (see “ExpressCard/Card Reader” on page 4 - 6).
Inserting and Removing Express­Cards
Align the ExpressCard with the slot and push it in
until it locks into place.
To remove an ExpressCard, simply press the card
to eject it.
ExpressCard Slot
Cover
Make sure you keep the cover in the Express­Card slot when not in use. This will help pre­vent foreign objects and/ or dust getting in to the ExpressCard Slot.
Figure 2 - 5
ExpressCard Slot
1. ExpressCard Slot
1
Page 54
Features & Components
2 - 8 Audio Features
2
Audio Features
You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notifi­cation area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume icon in the taskbar or the On Screen Display Indicators (see Table 1 - 3, on page 1 - 9).
Volume Adjustment
The sound volume level is set using the volume control within Windows (and the volume func­tion keys on the comput­er). Click the volume icon in the notification area to check the set­ting.
Figure 2 - 6
Realtek Audio
Manager
Right-click the icon to access the menu above.
Note that many keyboards have built-in controls to allow you to adjust the audio vol­ume.
Page 55
Features & Components
Audio Features 2 - 9
2
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instruc­tions below:
1. Click
Start
, and click
Control Panel
(or point to
Settings
and click
Control Panel
)
and make sure you are in
Classic View
.
2. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
3. Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust th e Recording Volume level to around 60, to obtain the optimum recording quality.
4. Click OK to close the control panel and save the settings.
Figure 2 - 7
Realtek Audio
Manager -
Recording Setup
Page 56
Features & Components
2-10
2
Page 57
Power Management
Overview 3 - 1
3
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
This chapter covers:
Turning On the Computer
Power Plans
Power-Saving States
Configuring the Power Buttons
Energy Star Power Saving
The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.
Using some form of power management greatly increases the life span of the LCD.
OS Note
Power management functions will vary slight­ly depending on your operating system. For more information it is best to refer to the user’s manual of your operat­ing system.
(Note: All pictures used on the following pages are from the Windows 7 OS.)
Page 58
Power Management
3 - 2 The Power Sources
3
The Power Sources
The computer can be powered by either the AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.
3. Adjust the LCD to a comfortable viewing angle.
4. Press the power button on the front of the computer for about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 15).
We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Energy Star Power Saving” on page 3 - 10.
Page 59
Power Management
Turning On the Computer 3 - 3
3
Turning On the Computer
Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the sys­tem to turn itself off.
Power Button as
Stand by or
Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the sys­tem into Stand by or Hi­bernate mode (see your OS’s documentation, or
“Configuring the Pow­er Buttons” on page 3
- 8 for details).
Shut Down
Note that you should always shut your computer down by choosing the Shut Down com­mand from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.
Page 60
Power Management
3 - 4 Power Plans
3
Power Plans
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.
Resuming
Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in or­der to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
Page 61
Power Management
Power Plans3-5
3
Each Windows power plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) pow­ered.
Figure 3 - 2
Power Plans
Click to Show/Hide additional power plans
Page 62
Power Management
3 - 6 Power-Saving States
3
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer do wn before the battery becomes depleted.
Page 63
Power Management
Power-Saving States 3 - 7
3
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.
Shut down
You should Shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.
Figure 3 - 3
Start Menu Power
Page 64
Power Management
3 - 8 Configuring the Power Buttons
3
Configuring the Power Buttons
The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Password
Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can dis­able this setting from the Power Options menu by clicking Require a
password on wakeup
in the left menu, and se­lecting the options (click
Change settings that are currently unavail­able).
Figure 3 - 4
Power Options
Define Power
Buttons
Page 65
Power Management
Configuring the Power Buttons 3 - 9
3
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).
Power Status
Icon Color
To Resume
Power Off Off Press the Power Button
Sleep Blinking Green
Press the Power Button
Press the Sleep Button
(see your keyboard documentation)
Hibernate
Off (battery)
Press the Power Button
Orange (AC/DC adapter)
Display Turned Off Green Press a Key or Move th e Mouse
Table 3 - 1
Resuming
Operation
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
Page 66
Power Management
3 - 10 Configuring the Power Buttons
3
Energy Star Power Saving
This system supports Energy Star power management features that place comput­ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. If you want to enable Energy Star power saving then follow these in­structions:
1. Right-click the taskbar icon (see sidebar).
2. Select Power Conservation Modes.
3. Select Energy St ar to use the Ener gy Star power management and override other power saving settings.
Figure 3 - 5
Energy Star Menu
Conservation Modes
The default Energy Star setting will result in maximum power sav­ing, but with the possible loss of some performance. Setting the mode to Balance will give power saving matched with performance. Performance will give optimum computer performance but with less power conservation.
Page 67
Power Management
Battery Information 3 - 11
3
Battery Information
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure
3 - 1 on page 3 - 4).
Click the battery icon in the notification area to see the current battery level and charge status.
Low Battery
Warning
When the battery is criti­cally low, immediately connect the AC/DC adapter to the computer or save your work, oth­erwise, the unsaved data will be lost when the power is depleted.
Figure 3 - 6
Battery Icon
(Notification Area) &
Battery Advanced
Settings
Page 68
Power Management
3 - 12 Battery Information
3
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
Reduce the amount of time before the display is turned off.
Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
Disconnect/remove any unnecessary external devices e.g. USB devices.
Windows Mobility
Center
The Windows Mobility Center control panel
provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Figure 3 - 7
Windows Mobility
Center
Page 69
Power Management
Battery Information 3 - 13
3
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”
on page 6 - 4.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 15 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 9 for information on the battery charge status, and to “Energy Star Power Saving” on page 3 - 10 for more information on how to maintain and prop-
erly recharge the battery pack.)
Page 70
Power Management
3 - 14 Battery Information
3
Proper handling of the Battery Pack
DO NOT disassemble the battery pack under any circumstances.
DO NOT expose the battery to fire or high temperatures, it may explode.
DO NOT connect the metal terminals (+, -) to each other.
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the comp uter continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.
Caution
Danger of explosion if battery is incorrectly re­placed.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s in­structions.
Page 71
Power Management
Battery Information 3 - 15
3
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
Figure 3 - 8
Power Plan Create
Page 72
Power Management
3 - 16 Battery Information
3
3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Figure 3 - 9
Change Plan
Settings / Change
Advanced Power
Settings
Page 73
Power Management
Battery Information 3 - 17
3
4. Scroll down to Battery and click + to expand the battery options.
5. Choose the options below (click Yes if a warning appears):
Low battery levels = 0%
Critical battery Levels = 1%
Low battery action = Do Nothing
Critical battery action (On battery) = Shut Down
Critical battery action (Plugged in) = Do Nothing
Figure 3 - 10
Power Options
Advanced Settings -
Battery
Page 74
Power Management
3 - 18 Battery Information
3
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 75
Drivers & Utilities
What to Install 4 - 1
4
Chapter 4: Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the lat­est versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.
What to Install
The Devic e Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that the drivers are installed in the order indicated (all drivers provided are for Windows 7 with Service Pack 1).
The procedures for installing drivers for the PC Camera, Wireless LAN and Bluetooth & WLAN Combo modules are provided in “Modules & Options” on page 7 - 1.
Driver Installation & Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source. Some drivers draw a significant am ou n t of power during the installation procedure, and if the remaining battery ca-
pacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).
Page 76
Drivers & Utilities
4 - 2 Driver Installation
4
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive and click Install Drivers/Op- tion Drivers (button).
Follow the instructions to install the driver. Alterna­tively click Start, navigate (Browse..) to the execut­able file and then follow the manual setup instructions.
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below .
2. Click to select the driver you wish to install, (you should note down the drivers as you install them).
3. Follow the instructions for each individual driver installation procedure as listed on the following pages.
Note: If you need to reinstall any driver, you should uninstall the driver first.
Figure 4 - 2 - Drivers Installer Screen 2
Page 77
Drivers & Utilities
Driver Installation 4 - 3
4
Table 4 - 1 - Driver Installation
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
Driver for Windows 7 with Service Pack 1 Page # Driver for Windows 7 with Service Pack 1 Page #
Chipset Page 4 - 6 PC Camera Module Page 7 - 2 Video Page 4 - 6 Wireless LAN Module Page 7 - 10 LAN Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 36 ExpressCard/Card Reader Page 4 - 6 Trusted Platform (Security) Module Page 7 - 43 Hotkey AP Page 4 - 6 USB 3.0 Page 4 - 7 MEI Driver Page 4 - 7 Audio Page 4 - 7
Page 78
Drivers & Utilities
4 - 4 Driver Installation
4
Manual Driver Installation
Click Bro wse CD/DVD (button) in the Drivers Install­er application and browse to the executable file in the
appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest securi ty updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows 7 Update” on page 4
- 8 for instructions.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro- grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea- tures menu:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Double-click Device Manager (Hardware and Sound > Device Manager).
3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4. Click Driver (tab) and click the Update Driver or Uninstall button and follow the on screen prompts.
Page 79
Drivers & Utilities
Driver Installation 4 - 5
4
User Account Control
If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as direct­ed.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
You will receive this message in cases where the driv­er has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” dur­ing the installation procedure (other than when out- lined in the driver install procedure), click Cancel to close the window, and follow the installation proce­dure.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slight­ly. As a general guide follow the default on screen in­structions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a re­start is required to install the driver.
Make sure any modules (e.g. PC Camera, WLAN or Bluetooth) are ON before installing the appropriate driv­er.
Page 80
Drivers & Utilities
4 - 6 Driver Installation
4
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual disc into your DVD drive and click Install Drivers (button).
Chipset
1. Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer .
Video
1. Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer .
LAN
1. Click 3.Install LAN Driver > Yes.
2. Click Install Drivers and Software > Next.
3. Click the button to accept the license and click Next.
4. Click Next > Install.
5. Click Finish.
6. The network settings can now be configured.
ExpressCard/Card Reader
1. Click 4.Install Cardreader Driver > Yes.
2. Click Finish.
Hotkey AP
1. Click 5.Install Hotkey AP > Yes.
2. Click Next > Next.
3. Click Finish > Finish to restart the computer.
Page 81
Drivers & Utilities
Driver Installation 4 - 7
4
USB 3.0
1. Click 6.Install USB 3.0 Driver > Yes.
2. Choose the language you prefer and click OK.
3. Click Next.
4. Click the button to accept the license agreement
and click Next.
5. Click Finish.
MEI Driver
1. Click 7.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish to restart the computer.
Audio
1. Click 8.Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To in­stall any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to ac­cess the optional driver menu.
(See Over)
Page 82
Drivers & Utilities
4 - 8 Driver Installation
4
Windows Experience Index
After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi- ence Index:
1. Click Start, and click Control Panel.
2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index).
3. Click “Rate this computer”.
4. The computer will take a few minutes to assess the system performance.
5. Close the control panel.
Windows 7 Update
After installing all the drivers make sure you enable Win­dows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con- nected to the internet:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Windows Update (System and Security).
3. Click Check for updates (button).
4. The computer will now ch eck for updates (you need to be connected to the internet).
5. Click Install now (button) to begin checking for the updates.
6. Click Install updates (button) to install the updates.
Page 83
Drivers & Utilities
Driver Installation 4 - 9
4
Optional Drivers
See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules in­cluded in your purchase option. Insert the Device Drivers & Utilities + User’s Manual disc and click Option Drivers (button) to access the optional driver menu.
Figure 4 - 3 - Optional Drivers
Page 84
Drivers & Utilities
4-10
4
Page 85
BIOS Utilities
Overview 5 - 1
5
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
If your computer has never been set up, or you are makin g important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Screens
Note that the BIOS screens pictured on these pages are intend­ed for guidance in set­ting up your system’s BIOS.
BIOS versions are sub­ject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
Page 86
BIOS Utilities
5 - 2 The Setup Utility
5
The Setup Utility
Each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
The Aptio Setup Utility tells the syst em how to configure itself and manage basic features and subsystems (e.g. port configuration).
To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup). If the Boot Logo is enabled the F2 on screen will be highlighted to illustrate that the system is processing the request during the POST (or press F7 for boot options). If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
To see the boot options press F7 and choose your preferred boot device.
Page 87
BIOS Utilities
The Setup Utility 5 - 3
5
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “non­fatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options.
Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
Page 88
BIOS Utilities
5 - 4 The Setup Utility
5
Setup Screens
The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make chang­es to Setup.
Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the upper right side of each screen explains the highlight- ed item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that sub­ject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configura­tion appropriate for your model and options.
Figure 5 - 1
Navigation Menu
Page 89
BIOS Utilities
Main Menu 5 - 5
5
Main Menu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
Figure 5 - 2
Main Menu
Page 90
BIOS Utilities
5-6Main Menu
5
SATA Port # (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports.
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
MB Series / BIOS Revision / KBC/EC firmware Revision
This item contains information on the BIOS version etc., and is not user configu­rable.
Page 91
BIOS Utilities
Advanced Menu 5 - 7
5
Advanced Menu
Advanced Chipset Control (Advanced Menu)
The sub-menu here allows you to adjust the Bluetooth Power Setting and Total Graphics Memory.
Figure 5 - 3
Advanced Menu
Page 92
BIOS Utilities
5 - 8 Advanced Menu
5
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)
You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
Total Graphics Memory (Advanced Menu > Advanced Chipset Control)
Use this menu item to set the amount of system memory to be allocated for use by Intel
®
Dynamic Video Memory Technology for the graphics device. The default
memory size allocated is Max (up to 1748MB) and this may be adjusted to 128MB or 256MB (by pressing the spacebar to adjust) if required (see “Dynamic Video
Memory Technology” on page B - 1).
SATA Mode Selection (Advanced Menu)
You can configure SATA (Serial ATA) control to operate in IDE (native/compati­ble), AHCI (Advanced Host Controller Interface) modes from this menu. The SATA Mode should be set BEFORE installing an operating system, and after you have backed up all necessary files and data (see sidebar).
SATA Mode
Selection
If you have installed the Windows 7 operating system with either IDE
or AHCI mode enabled, DO NOT disable the set
mode (if you wish to dis­able the set mode you will need to reinstall the Windows 7 OS).
Page 93
BIOS Utilities
Advanced Menu 5 - 9
5
Boot Logo (Advanced Menu)
Use this menu item to enable/disable th e Boot Logo screen at system startup. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
Super IO Configuration (Advanced Menu)
Use this menu to enable/disable and configure the serial (RS-232) ports to your re­quirements. Change Settings allows you to change the IO and IRQ settings, and De- vice Mode allows you to set the ports to normal or high speed modes.
Page 94
BIOS Utilities
5 - 10 Security Menu
5
Security Menu
Password on boot (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled is selected, only users who enter a correct password can boot the system (see the warning in the sidebar).
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
Figure 5 - 4
Security Menu
Page 95
BIOS Utilities
Security Menu 5 - 11
5
Set Supervisor Password (Security Menu)
You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility). If you set a supervisor password you can then add a user password.
Set User Password (Security Menu)
You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Aptio Setup Utility cannot be modified in user mode. You can only set the user password after you
have set the supervisor password.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Interface Items (Security Menu)
The interfaces for the ExpressCard (New Card), Card Reader, WLAN, LAN, Audio and ODD (optical device drive) may be enabled/disabled from the menu items here if required.
Password Warning
If you set a boot pass­word (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your ven­dor and you may lose all of the information on your hard disk.
Page 96
BIOS Utilities
5 - 12 Security Menu
5
Secure Boot (Advanced Menu)
Enable/disable Secure Boot from this menu. The Secure Boot specification pro­vides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, Secure Boot defines a set of standard boot and runtime services. Secure Boot may be set to Standard (with a fixed Secure Boot policy), or Custom (which allows changes to execution policy and Secure Boot databases).
Configuration (Security Menu)
This sub-menu will allow you to enable/d isable the Trusted Platform Module (TPM) Security Device Support, and to configure the TPM State. Select Configuration and press Enter to access the sub-menu. Press Enter to access the (TPM) Configu- ration menu and select Enable to display the full TPM configuration menu (see
“Trusted Platform (Security) Module” on page 7 - 43 for details).
Page 97
BIOS Utilities
Boot Menu 5 - 13
5
Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows
7) from the devices listed in this menu, and in this priority order. If it cannot find
the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities. Item specific help on the right is available to help you move devices up and down the order.
Figure 5 - 5
Boot Menu
BIOS Screens
Note that the BIOS screens pictured on these pages are intend­ed for guidance in set­ting up your system’s BIOS.
BIOS versions are sub­ject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
Page 98
BIOS Utilities
5 - 14 Boot Menu
5
Fast Boot / UEFI Boot (Boot Menu)
Fast Boot will enable a boot with the minimal set of devices required (the sub-menus will allow you to choose to skip the EFI VGA driver, USB devices and/or PS/2 de­vices. You can also choose to enable/disable boot from UEFI devices.
Boot Option Priorities (Boot Menu)
Use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list. You can go to either Network Device BBS Priorities,
CD/DVD ROM Drive Priorities or Hard Drive BBS Priorities and use the
+ and
- keys to move the device’s boot priority up and down the list (the selected device
will be highlighted in white).
Wake-up On LAN (Boot Menu)
Enable/disable the Wake-up On LAN feature here. If enabled network activity will wake up the computer from sleep.
Page 99
BIOS Utilities
Exit Menu 5 - 15
5
Exit Menu
Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made
to the Setup. You can also choose Load Setup Defaults to restore the original Setup defaults and return the Setup to its original state, and erase any previous changes you have made in a previous session.
Figure 5 - 6
Exit Menu
Page 100
BIOS Utilities
5-16
5
Loading...