V09.1.20
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©June 2009
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC
Output of 19V, 1.58A or 19V, 1.57A (30 Watts) minimum AC/DC Adapter.
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
III
Preface
Instructions for Care and Operation
The computer is rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
• Do not place it on an unstable surface.
• Do not place anything heavy on the computer
2.
Keep it dry , an d don’t overhea t it.
This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
• Do not expose it to excessive heat.
• Do not leave it in a place where foreign matter or moisture may affect the system.
• Don’t store the computer in a humid environment.
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down proper ly and don ’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted
• Do not turn off the power until you properly sh ut down all programs.
• Do not turn off any peripheral devices when the computer is on.
• Do not disassemble the computer by yourself.
• Perform routine maintenance on your computer.
5. Take care when using peripheral devices.
• Use only approved brands of peripherals.
• Unplug the power cord before attaching peripheral devices.
Keep the computer and power supply away from any kind of he ating element.
IV
Power Safety
The computer has specific power requirements:
Preface
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninterru pted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
V
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Pay careful attention to the instructions on swapping the battery.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the computer’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qual-
ified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VI
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
4. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
5. Put the computer in its carrying bag and secure it with the bag’s straps.
6. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
7. Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hardware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your computer is completely powered off before putting it into a travel bag (or any such container).
VII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the computer - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
VIII
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly belo w the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
IX
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
• Set the Windows Power Schemes to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
X
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
XI
Preface
Upgrading the Memory and HDD/SSD
If you want to upgrade your computer by upgrading the system memory or the hard disk drive/solid state drive
you will need to contact your customer service representative. We recommend that you do not do this yourself,
since if it is done incorrectly you may damage the mainboard.
Warranty Warning
Please check with your service representative before undertaking any up grade procedures to find ou t if this will VOID your
warranty.
The CPU is not a user serviceable part. Accessing the CPU in any way, may violate your warranty.
Unauthorized tampering with the HDD may also violate your warranty.
XII
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
Instructions for Care and Operation ..........................IV
Power Safety ...............................................................V
Battery Precautions ....................................................VI
Travel Considerations ...............................................VII
Cleaning ..................................................................... XI
Servicing .................................................................... XI
Quick Start Guide
Overview ........................................................................1-1
Introduction ....................................................................1-2
LED Backlight LCD ....................................................1-2
Advanced Users ...........................................................1-5
Beginners and Not-So-Advanced Users ......................1-5
Warning Boxes ............................................................1-5
Not Included ................................................................1-6
System Software ..........................................................1-7
System Startup ...............................................................1-8
Operating System Setup ................................................1-9
System Software Installation .....................................1-10
Operating System Installation ..................................1-10
Tablet Notebook Input .................................................1-11
Preface
Calibrating the Touch Panel .....................................1-11
Pen Options & Tablet Settings .................................1-13
On-Screen Keyboard ................................................1-14
System Map: LCD Panel View - Front ........................1-15
LED Indicators ..........................................................1-16
Function Buttons ........................................................1-17
On-Screen Menu ..........................................................1-18
G-Sensor - Hard Disk Drive Protection .......................1-20
System Map: Rear View ..............................................1-21
System Map: Left View ...............................................1-22
System Map: Right View .............................................1-23
System Map: Top & Bottom Views ............................1-24
Windows Vista Start Menu & Control Panel ...............1-25
Video Features .............................................................1-26
Display Devices & Options ......................................1-26
Power Options ............................................ .... .... ..........1-28
Optimizing Battery Life .............................................1-29
Removing the Battery ..................................................1-30
Hot-Swapping the Battery ...........................................1-31
Features & Components
Overview ........................................................................2-1
Hard Disk Drive/Solid State Drive ................................2-2
XIII
Preface
5-in-1 Card Reader ........................................................2-3
ExpressCard Slot ...........................................................2-4
Inserting and Removing ExpressCards .......................2-4
Audio Features ...............................................................2-5
Tablet PC Options ..........................................................2-6
Screen Orientation .......................................................2-7
Adding a Printer ...........................................................2-12
USB Printer .......................................................... ....2-12
Parallel Printer ..........................................................2-12
Power Management
Overview ........................................................................3-1
The Power Sources ........................................................3-2
AC/DC Adapter ................................................. .... .... ..3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Plans ...................................................................3-4
Power-Saving States ......................................................3-6
Sleep ...........................................................................3-6
Hibernate ....................................................................3-7
Shut Down ..................................................................3-7
Configuring the Power Buttons .....................................3-8
Resuming Operation ...................................................3-9
Battery Information .....................................................3-10
Battery Power ...........................................................3-10
Conserving Battery Power .........................................3-11
Battery Life ................................................................3-12
New Battery ..............................................................3-12
Recharging the Batter y with the AC/DC Adapter .....3-12
Proper handling of the Battery Pack .........................3-13
Battery FAQ ..............................................................3-14
Battery Gauge ...........................................................3-16
Battery Indicators ......................................................3-17
Drivers & Utilities
What to Install ............................................................... .4-1
Module Driver Installation ..........................................4-1
Driver Installation ..........................................................4-2
Updating/Reinstalling Individual Drivers ...................4-4
User Account Control (Win Vista) ..............................4-4
Windows Security Message .........................................4-4
New Hardware Found ..................................................4-4
Driver Installation Procedure .......................................4-5
Chipset ........................................................................ 4-5
Video ..........................................................................4-5
LAN ............................................................................4-5
Touch Panel Application ............................................4-6
Pop Menu Utility ........................................................4-6
Audio ..........................................................................4-6
Optional Drivers ..........................................................4-7
XIV
Preface
Bluetooth Module .......................................................4-7
Wireless LAN Module ...............................................4-7
PC Camera Module ....................................................4-7
Fingerprint Reader Module ........................................4-7
BIOS Utilities
Overview ........................................................................5-1
The Power-On Self Test (POST) ................................... 5-2
Failing the POST .........................................................5-3
Fatal Errors .................................................................5-3
Non-Fatal Errors .........................................................5-3
The Setup Program ........................................................5-4
Entering Setup .............................................................5-4
Setup Screens ......................................................... ......5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ...............................5-6
Large Disk Access Mode (Main Menu) ........................5-7
Primary Master/ Primary Slave (Main Menu) ...............5-7
System/Extended Memory: (Main Menu) .....................5-7
Advanced Menu .............................................................5-8
Installed O/S (Advanced Menu) ....................................5-8
Reset Configuration Data (Advanced Menu) ................5-9
Boot-time Diagnostic Screen (Advanced Menu) ...........5-9
POST Beep Sound (Advanced Menu) ...........................5-9
Battery Low Alarm Beep (Advanced Menu) .................5-9
Hyperthreading (Advanced Menu) ................................5-9
Security Menu ..............................................................5-10
Set Supervisor Password (Security Menu) ..................5-10
Set User Password (Security Menu) ............................5-11
Diskette access (Security Menu) ..................................5-11
Virus check reminder (Security Menu) .......................5-11
System backup reminder (Security Menu) ..................5-12
Password on boot (Security Menu) ..............................5-12
Boot Menu ...................................................................5-13
Exit Menu ....................................................................5-14
Modules
Overview ........................................................................6-1
Bluetooth Module ..........................................................6-2
Bluetooth Configuration in Windows Vista ...............6-3
Wireless LAN Module ...................................................6-6
802.11b/g Driver Installation ......................................6-6
Connecting to a Wireless Network .............................. 6-7
PC Camera Module ......................................................6-11
PC Camera Driver Installation .................................6-11
Fingerprint Reader Module ..........................................6-17
Fingerprint Reader Driver Installation .....................6-17
User Enrollment ........................................................6-18
Fingerprint Control Center Features ......................... 6-21
GPS Module .................................................................6-22
XV
Preface
Configuring the COM Port for the GPS Module ......6-23
RFID Reader Module ..................................................6-24
Configuring the COM Port for the RFID Reader .....6-25
Troubleshooting
Overview ........................................................................7-1
Basic Hints and Tips ......................................................7-2
Backup and General Maintenance .................................7-3
Viruses ........................................................................... 7-4
Adding New Hardware/Software ..................................7-5
Problems and Possible Solutions ...................................7-7
Interface (Ports & Jacks)
Ports and Jacks ..............................................................A-1
Intel Video Driver Controls
Video Driver .............................................................. B-1
Specifications
Processor Options ......................................................... C-2
Core Logic ....................................................................C-2
LCD Options .................................................................C-2
Memory .........................................................................C-2
Video Adapter ...............................................................C-2
Video Camera ............................................................... C-2
BIOS .............................................................................C-2
Drop Protection .............................................................C-2
Storage .......................................................................... C-2
Audio ............................................................................C-2
Button Keys ..................................................................C-2
Interface ........................................................................ C-2
Card Reader/ExpressCard .............................................C-3
Communication .............................................................C-3
Security ......................................................................... C-3
Power Management ............................................... ... ....C-3
Power ............................................................................ C-3
Operating System ..........................................................C-3
Environmental Spec ......................................................C-3
Dimensions & Weight ..................................................C-3
Indicators ......................................................................C-3
Optional ........................................................................C-3
Factory Options .............................................................C-4
Windows XP Information
Tablet Notebook Input ..................................................D-2
Calibrating the Touch Panel ......................................D-2
On-Screen Menu ...........................................................D-4
G-Sensor - Hard Disk Drive Protection ........................D-6
Windows XP Start Menu & Control Panel ...................D-7
Audio Features ..............................................................D-8
XVI
Preface
Video Features ..............................................................D-9
Attaching Other Displays ...........................................D-12
Display Modes ............................................................D-13
Power Management Features ......................................D-17
The Power Sources .....................................................D-18
Turning on the Computer ............................................D-19
Power Schemes ...........................................................D-20
System Power Options ................................................D-22
Configuring the Power Button ....................................D-24
Battery Information ....................................................D-25
Battery Guidelines ...................................................D-27
Battery Gauge ..........................................................D-28
Battery Indicators .....................................................D-29
Removing the Battery .................................................D-30
Hot-Swapping the Battery ..........................................D-31
Driver Installation .......................................................D-32
Bluetooth Module .................................................... ...D-37
Bluetooth Configuration in Windows XP ...............D-39
To Add a Bluetooth Device .....................................D-40
Wireless LAN Module ................................................D-42
PC Camera Module .....................................................D-44
Fingerprint Reader Module .........................................D-49
User Enrollment ................................................ .... ...D-50
Fingerprint Control Center Features ........................D-53
GPS Module ................................................................D-54
RFID Reader Module ..................................................D-56
ExpressCard 34 Approved List
XVII
Preface
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk/
Solid State Drive, 5-in-1 card reader, ExpressCard), Audio, Tablet PC Options & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 A quick guide to the computer’s Bluetooth, Wireless LAN, PC Camera, GPS, RFID Reader
modules (some of which are optional).
• Chapter 7 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to com munic ate wi th ex ternal
devices.
• Appendix B Information on the Intel Video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Introduction
This semi-ruggedized tablet computer provides an ideal platform for outdoor computer use with an IP54 (Ingress
Protection) rating against dust and spray and features an optional sunlight readable LCD touch panel; all touch
panels support both finger and stylus pen input. Hard disk drive protection is provided by G-Sensor sof tware that
protects the hard disk drive from a drop of up to 40CM when the system is powered on, and the hard disk drive
is shock mounted offering protection from a drop of 120CM when the system is powered off.
Spray Resistant
Note that the computer is spray resistant with a
Ingress protection rating of 4 (i.e protection from
splashed water). Note that spilling liquids directly
on, or immersing the computer in water may violate your warranty.
Figure 1 - 1 - Spray Resistant Computer
LED Backlight LCD
The LED Backlight LCDs on this computer model allow for greater color quality and consume less power than
conventional fluorescent LCDs, and therefore can save significant ba ttery life. In addition the LED b acklit LCD
allows for clearer reading in sunlit conditions.
1 - 2 Introduction
Quick Start Guide
Optional Accessories
This computer features a range of options including a GPS module (including an optional active aerial), HF
RFID reader, as well as a range of optional accessories including car adapter, charger box, USB to RS 232 cable,
hand holder, shoulder strap and carrying handle.
1
Figure 1 - 2 - Optional Accessories
Introduction 1 - 3
1
Quick Start Guide
Attaching the Optional Hand Holder.
The hand holder offers ease of use when using the computer on the move outdoors. Attach the hand holder as
follows:
1. Place the hand holder at the rear of the computer with the screws facing inwards towards the computer.
2. Align the screws on the hand holder with the screw holes
adjust the straps to do this).
3. Fully tighten the screws
4. Put your hand through the hand holder and secure it with the velcro straps & .
5 8
- using a flathead screwdriver.
1 4
- in the rear of the case (you may need to
9 10
1
4
1 - 4 Introduction
2
5
3
Figure 1 - 3 - Attaching the Optional Hand Holder
8
6
7
9
10
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the reminder of the User’s
Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
Notes
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1
Introduction 1 - 5
1
Quick Start Guide
Not Included
Operating Systems (e.g. Windows Vista or XP) and applications (e.g. word processing, spreadsheet and database
programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1 (you will need an external USB optical device driv e). Drivers are
programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It
is very important that you install the drivers in the order listed in. You will be unable to use most advanced contro ls until
the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you); refer to Chapter 4 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 1 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1 - 6 Introduction
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the following operating systems are supported.
Operating System & Version Note
1
*Windows XP - SP3 (32-bit) Home or
Professional
Windows Vista - SP1 (32-bit)
Home Basic Edition
Table 1 - 1 - Operating Systems Supported
In order to run Windows XP without limitations or
decreased performance, your computer requires a
minimum 512MB of system memory (RAM)
In order to run Windows Vista without limitations or
decreased performance, your computer requires a
minimum 1GB of system memory (RAM).
*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-
dows XP Information” on page D - 1.
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1 (or a Windows Vista version which includes Service Pack 1) before
installing any drivers. Go to the Microsoft website for download details, or contact your service center.
Introduction 1 - 7
1
Quick Start Guide
System Startup
1. Remove all packing materials.
2. Place the computer flat on a stable surface with LCD panel facing upwards.
Shutdown
Please note that you should always shut
your computer down by choosing the Turn
Off Computer command from the Start
menu in Windows. This will help prevent
hard disk or system problems.
External Optical (CD/DVD) Device Drives
To install applications and drivers etc. you
will need to attach an external optical CD/
DVD device to the USB ports.
Figure 1 - 4 - Computer with AC/DC Adapter Plugged-In / Computer with Stylus Pen
3. Securely attach any peripherals you want to use with the computer (e.g. keyboard or mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Press the power button to turn the computer “on”.
6. Remove the Stylus pen to use as your input device.
7. The LED indicators show the power and battery status of the computer.
Touch Panel Input
Do not use any sharp or pointed objects as your input device e.g. the end of a pen or
pencil. You should only use
the provided stylus pen (PDA
type) as your input device. Be
very careful not to press too
hard with the stylus pen when
using it as the input device.
Device
1 - 8 System Startup
Quick Start Guide
Operating System Setup
If you are installing new system software, or are re-configuring your computer for a different system, make sure you
configure the appropriate OS setting in the BIOS before installing a new operating system.
1. Start-up the computer and press <F2> to enter the BIOS.
2. Go to the Advanced menu, select “Installed O/S” and make sure the appropriate operating system is selected.
3. Go to the Exit menu and select “Exit Saving Changes” (or press F10 and select “Yes” then press Enter) and
press Enter to exit the BIOS and reboot the computer.
Main AAdvanced Security Boot Exit
Installed O/S: [WinXP/Vista]
Reset Configuration Data: [No]
Boot-time Diagnostic Screen: [Disabled]
POST Boot Sound [Disabled]
Battery Low Alarm Beep: [Disabled]
Hyperthreading: [Enabled]
Advanced
Phoenix SecureCore(tm) Setup Utility
Item Specific Help
Select the operating
system installed on
your system which you
will use most
commonly.
Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.
1
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Figure 1 - 5 - Advanced BIOS Menu
Operating System Setup 1 - 9
1
Quick Start Guide
System Software Installation
Your computer may come with an operating system software and all necessary drivers pre-installed. If you are
installing new system software, or are re-configuring your computer for a different sy stem, you will need to install the drivers after installing the operating system.
Operating System Installation
Prepare the following before installing the Microsoft Windows Vista Home Basic Edition - 32-bit (with Service
Pack 1) or Microsoft Windows XP - 32-bit (with Service pack 3) operating system software:
• An external USB CD/DVD device drive (the Microsoft Windows OS CD should be inserted into this drive).
•The Device Drivers & Utilities + User’s Manual Disc.
• A USB keyboard connected to one of the USB ports.
4. Attach the external USB CD/DVD device drive (containing the Microsoft Windows OS CD) to the computer.
5. Start-up your computer and press <F2> to enter the BIOS.
6. Go to the Boot menu (see “Boot Menu” on page 5 - 13).
7. Set the external CD/DVD-ROM Drive (make sure the Microsoft Windows OS CD is inserted) as the first
device in the boot order from the Boot priority order menu (use the “+” and “-” keys to move the device up and
down the priority order.
8. Select Exit Saving Changes from the Exit menu (or press F10 and Enter) and press Enter to exit the BIOS and
reboot the computer.
9. As the computer starts up, press a key when you see the message "Press any key to boot from CD".
10. The system software will prompt you through the installation procedure (see the Microsoft Windows OS
documentation for more details).
11. Install the drivers as per the instructions in Chapter 4 (in the order indicated in Table 4 - 1, on page 4 - 3).
1 - 10 Operating System Setup
Quick Start Guide
Tablet Notebook Input
Use the stylus pen provided to interact with the computer in the same way you would use the mouse (tap twice
to double-click and keep the pen in contact with the scr een to right-click). Before using the stylus pen you should
calibrate the touch screen.
Calibrating the Touch Panel
1. Double-click the Touch tool utility icon on the desktop OR from the Touch Package folder in the Pro-
grams/All Programs group (the driver must be installed).
2. Click General.
3. Click 9 pts Linearity (if you would prefer to calibrate more accurately, or are having distortion/tracking
problems, then click Advance and choose either 25 pts Linearity).
1
Figure 1 - 6 - Touch Package (General & Advance)
Tablet Notebook Input 1 - 11
1
Quick Start Guide
4. Use the stylus pen to touch the blinking symbol until symbol changes color (maintain contact until the symbol stops blinking)
and you will be prompted to lift up the pen.
5. Repeat the process for all the remaining screen points.
6. Click Free Draw (button) to test the calibration.
7. Use the Mouse Emulation and Sound control panels to further adjust the settings to your preference.
Touch Panel Input
Device
Do not use any sharp or
pointed objects as your
input device e.g. the end
of a pen or pencil. You
should only use the provided stylus pen (PDA
type) as your input device. Be very careful not
to press too hard with the
stylus pen when using it
as the input device.
1 - 12 Tablet Notebook Input
Screen Distortion
If you experience any line
distortion, or tracking inaccuracy, recalibrate the
touch screen using 25pts
of calibration (click the
Advance item in the
Touch package and
click 25pts Linearity).
Figure 1 - 7 - Screen Calibration
Quick Start Guide
Pen Options & Tablet Settings
Configure the stylus pen input settings, from the Pen and Input Devices control pane in Windows Vista; the
Tablet PC Settings control panel allows you to configure the tablet screen appearance. Access the control panels
as follows:
1. Click
2. Click Mobile PC and click Pen and Input Devices (or just double-click Pen and Input Devices).
3. Click Mobile PC and click Tablet PC Settings (or just double-click Tablet PC Settings).
Start
, and click
Control Panel
(or point to
Settings
and click
Control Panel
).
Tablet PC Options
See “Tablet PC Options”
on page 2 - 10 for further
information on Tablet PC
settings etc.
1
Figure 1 - 8 - Pen and Input Devices & Tablet PC Settings Control Panel
Tablet Notebook Input 1 - 13
1
Quick Start Guide
On-Screen Keyboard
The On-Screen Keyboard allows you to input text without the use of a keyboard. Move the pen over any character and then tap it to activate it.
1. Click
2. Double-click Ease of Access and click Start On-Screen Keyboard.
3. Use the stylus pen to tap the appropriate keys to input.
4. Click the Help menu to get more information.
Start
, and click
Control Panel
(or point to
Figure 1 - 9 - On-Screen Keyboard
Settings
and click
Control Panel
).
Note: You can use the Ease of Access icon at system startup (at the point of system password entry) to bring
up the On-Screen Keyboard and input the system password.
1 - 14 Tablet Notebook Input
System Map: LCD Panel View - Front
Quick Start Guide
Figure 1 - 10
LCD Panel View - Front
1
1
2
7
3
4
5
6
7
4
1. Built-In Microphone
2. LED Indicators
3. LCD Touch Panel
Screen
4. Speakers
5. Fingerprint Reader
6. 5 Function Buttons
7. Protective
Surround
2
System Map: LCD Panel View - Front 1 - 15
1
Quick Start Guide
LED Indicators
The LED indicators on the computer display helpful information about the current status of the computer.
Icon Color Description
Orange DC Power is Plugged In
Green The Computer is On
Blinking Green The Computer is in Sleep Mode
Orange The Battery is Charging
Green The Battery is Fully Charged
Blinking Orange The Battery Has Reached Critically Low Power Status
Green Hard Disk / System Activity
Table 1 - 2 - LED Indicators
1 - 16 System Map: LCD Panel View - Front
Quick Start Guide
Function Buttons
The function buttons provide easier access to functions on the computer.
Key Buttons Icon Description
Page Mode / Zoom Mode Toggle
Access / Hide the On-Screen Menu
Page Mode = Page Up / Page Down
Zoom Mode (for Picture files - Does NOT Zoom the Camera) =
Zoom In / Zoom Out
Run the BisonCap Application
If the BisonCap Application is Running = Take Still Picture
Table 1 - 3 - Function Buttons
Press the Camera Button to run the BisonCap application program (for PC Camera). When the BisonCap
application program is running, press the Camera Button to take a still picture.
1
Use the Zoom Mode (press the Mode Toggle Button to toggle Zoom and Page Modes) to zoom in and
out of open picture files (e.g. bitmap, jpeg files etc.).
Use the Page Mode to Page Up and Page Down text files etc.
System Map: LCD Panel View - Front 1 - 17
1
Quick Start Guide
On-Screen Menu
Pressing the Menu button (or double-click the Pop Menu icon in the taskbar) on the computer will bring up
the on-screen menu (make sure you install the pop menu driver - see “Pop Menu Utility” on page 4 - 6). Use
the stylus pen to touch any of the buttons to activate the control. Press the Menu button (or double-click the Pop
Menu icon in the taskbar) to quit the menu. Use the stylus pen to tap the appropriate on-screen button to
adjust the setting and the button will display the current status.
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic
transmission devices aboard aircraft is usually prohibited. Make
sure the module(s) are OFF if you
are using the computer aboard aircraft.
Use the On-Screen Menu button
to toggle power to any Wireless/
Bluetooth/GPS module, and check
the menu icon to see if the module
is powered on or not.
1 - 18 On-Screen Menu
Figure 1 - 11 - On-Screen Menu
Quick Start Guide
Function On-Screen Button Function On-Screen Button
1
Brightness
Decrease/Increase
Volume Decrease/
Increase
Mute Toggle
Display Toggle
Display Battery
Level
WLAN Module
Power Toggle
Bluetooth Module
Power Toggle
PC Camera Module
Power Toggle
G-Sensor
Protection Mode
Toggle
GPS Module Power
Toggle
RFID Module
Power Toggle
Note: Any modules not included in your purchase configuration will appear grayed out when the key combination is pressed.
Note: Use the stylus pen to tap the appropriate on-screen button to adjust the setting.
Note: The default setting for the Wireless LAN and PC Camera modules is OFF.
Table 1 - 4 - On-Screen Menu Buttons
On-Screen Menu 1 - 19
1
Quick Start Guide
G-Sensor - Hard Disk Drive Protection
The built-in G-Sensor gives protection to the system and hard disk (the G-Sensor does not function with Solid
State Drives) in the event that the computer is accidentally dropped when the system is powered on (40cm drop
approved when the system is powered on and 120cm drop approved when the system is powered off). Press
the Menu button (or double-click the Pop Menu icon in the taskbar) to bring up the on-screen menu and use
the stylus pen to toggle the G-Sensor mode ON or Off .
If the system is dropped, and the G-Sensor is on, the system will briefly pause (for about 3 seconds) to protect
the hard disk and will display an on-screen message and an audible warning) to inform that the hard disk is protected. Allow the system about 3 seconds to recover before using it again.
Figure 1 - 12 - HDD Protected Message
Set the G-Sensor On or Off in accordance with the manner the computer is being used. If the computer is sitting
on the desktop (or if you find the G-Sensor is too sensitive), then the G-Sensor can be turned Off. The G-Sensor
will be automatically activated to offer protection when the computer enters Sleep or Hibernate modes (even if
turned off).
1 - 20 G-Sensor - Hard Disk Drive Protection
Quick Start Guide
1
System Map: Rear View
3
5
6
Figure 1 - 13
LCD Rear View -
2
1
3
4
1. Built-In PC Camera
2. GPS Active Aerial
Socket (for
optional Active
Aerial)
3. Protective
Surround
4. Stylus Pen &
Holder
5. Battery Gauge
6. Battery
Battery Information
See “Battery Informa-
tion” on page 3 - 9 for full
instructions.
System Map: Rear View 1 - 21
1
Quick Start Guide
Figure 1 - 14
Left View
1. Security Lock Slot
2. Stylus Pen &
Holder
3. DC-In Jack
4. 1 * USB 2.0 Port
Mouse & Keyboard
You can use any external
mouse and keyboard attached to any of the USB
ports.
System Map: Left View
1
2
1
2
Touch Panel Input Device
Do not use any sharp or pointed objects as your input d evice e.g. the end of a pen or pencil. You should only use
the provided stylus pen (PDA type) as your input device.
Be very careful not to press too hard with the stylus pen
when using it as the input device.
3
3
4
4
External Optical (CD/
DVD) Device Drives
To install applications
and drivers etc. you will
need to attach an external optical CD/DVD
device to the USB
ports.
1 - 22 System Map: Left View
Quick Start Guide
1
System Map: Right View
1 3
1
2
5-in-1 Card Reader
The card reader allows you to use the most popular digital storage card
formats:
SD (Secure Digital)
Mini SD (requires PC adapter)
SDIO (requires PC adapter)
MMC (MultiMedia Card)
RS MMC (requires PC adapter)
2
4
5
Figure 1 - 15
Right View
1. Headphone-Out
Jack
2. External Monitor
Port
3. Card Reader
Cover
4. ExpressCard 34
Slot (see below)
5. 5-in-1 Card
Reader
ExpressCard Support
There is a list of approved
ExpressCard modules listed
on Table E - 1, on page E -
1 Please make sure any Ex-
pressCards modules you
use with this computer are
included in the list. Contact
your service center for further information.
System Map: Right View 1 - 23
1
Quick Start Guide
Figure 1 - 16
Top & Rear Views
1. Strap Holders (for
Carrying Strap)
2. Power Button
3. RFID (Radio
Frequency
Identification)
Reader (Factory
Option)
4. RJ-45 LAN Jack
5. 1 * USB 2.0 Ports
System Map: Top & Bottom Views
1 1
2 3
4
5
External Optical (CD/DVD) Device Drives
To install applications and drivers etc.
you will need to attach an external optical
CD/DVD device to the USB ports.
1 - 24 System Map: Top & Bottom Views
Quick Start Guide
Windows Vista Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.
Click here to toggle Classic View
Figure 1 - 17 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers provided. To see all controls it may be necessary to toggle to Classic View on.
1
Windows Vista Start Menu & Control Panel 1 - 25
1
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed.
To access Display Settings in Windows Vista:
1. Click
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization >
3. Move the slider to the preferred setting in Resolution: (Figure 1 - 18 on page 1 - 27).
4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 18 on page 1 - 27).
5. Click Advanced Settings (button) (Figure 1 - 18 on page 1 - 27) and click Intel(R) GMA Driver for ultra mobile (tab).
6. Click Graphics Properties (button) (Figure 1 - 18 on page 1 - 27) to access the Intel GMA Driver for ultra mobile
7. The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display
connected to the external monitor port as your display device. Note: MID (Mobile Internet Device) is the computer’s LCD display.
Start
, and click
Display Settings).
control panel (this control panel can also be accessed by double-clicking Intel(R) GMA Driver for ultra mobile control panel
in Windows Classic View).
from the menu.
Control Panel
(or point to
3
4
Settings
and click
1
2
Control Panel
).
1 - 26 Video Features
Quick Start Guide
1
1
2
4
3
Figure 1 - 18 - Display Properties Desktop
Intel Display Mode Description
Single Mode One of the connected displays is used as the display device
Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured ind ependently
Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop
Table 1 - 5 - Display Options
Video Features 1 - 27
1
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 25 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, display and sleep mode from the left menu. Note
that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-
figuration options.
1 - 28 Power Options
Note: Sleep is the default power saving state in Windows Vista
Figure 1 - 19 - Power Options
Quick Start Guide
Optimizing Battery Life
To optimize your battery life, follow the instructions below and also see “Conserving Battery Power” on page 3
- 10. You can check the battery’s current capacity from the gauge at the rear of the computer (see “Battery
Gauge” on page 3 - 16).
Set the Power Plan to Power saver:
1. Click
2. Double-click Power Options (icon); Power Options (icon) is in the System and Maintenance category.
3. Click Power saver (button) in select Select a power plan.
4. Close the control panel.
Power Off any modules not in use:
1. Press the Menu button (or double-click the Pop Menu icon in the taskbar).
2. Use the stylus pen to touch any of the buttons to turn of f any module not in current use (e.g. came ra, Bluetooth,
Start
, and click
WLAN etc.).
Control Panel
(or point to
Settings
and click
Control Panel
).
1
Figure 1 - 20 - Power Saver Power Plan
Power Options 1 - 29
1
Quick Start Guide
Removing the Battery
If you need to remove the battery follow the procedure below.
1. Turn the computer off (unless you are hot swapping the battery), and turn it over.
2. Remove screws at points - .
3. Remove the battery cover .
4. Grip the tab and lift the battery out in the direction of the arrow .
6 7
1 4
5
2
1
1 - 30 Removing the Battery
3
4
5
Figure 1 - 21 - Battery Removal
6
7
Quick Start Guide
Hot-Swapping the Battery
If you have more than one battery included in your purchase option you can swap the battery while the system
is running.
1. Check the level of the backup battery from the on-screen menu.
2. Press the battery level button to display the indicator:
Main Battery Level
Bridge Battery Level
Figure 1 - 22 - Battery Level Indicator
3. The lower indicator will display the bridge battery level and the upper indicator displays the main battery level.
4. If the bridge battery level indicated “Ready” you can swap batteries.
5. Remove the AC/DC adapter cable from the DC-In jack (if applicable) and an on-screen icon will indicate the
main battery status if less than a 3% charge remains.
Battery Less than 3% Charge - Plug-in Adapter to ChargeBattery Less than 3% Charge - Change Battery
Figure 1 - 23 - Bridge Battery Ready Indicators
6. You can then remove the battery as per the instructions in “Removing the Battery” on page 1 - 3 0.
7. When the battery is removed a beep will indicate that the system is running on bridge battery power (you have
up to 3 minutes maximum to swap the battery depending upon applications being used).
8. When a new sufficiently charged battery is inserted the beep will stop.
1
Hot-Swapping the Battery 1 - 31
1
Quick Start Guide
1 - 32
Features & Components
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components
of the computer.
• Hard Disk Drive/Solid State Drive
• 5-in-1 Card Reader
• ExpressCard Slot
• Audio Features
• Tablet PC Options
• Adding a Printer
2
Overview 2 - 1
Features & Components
2
If you want to upgrade
your computer by upgrading the hard disk
drive/solid state drive
you will need to contact
your customer service
representative. We recommend that you do not
do this yourself, since if
it is done incorrectly you
may damage the computer.
Upgrading the
HDD/SSD
Hard Disk Drive/Solid State Drive
The hard disk drive or solid state drive (factory options) is used to store your data
in the computer. The HDD/SSD can be taken out (please check with your service
representative before undertaking any upgrade or replacement procedures to find out
if this will VOID your warranty) to accommodate other 2.5" serial (SATA) HDDs/
SSDs (SLC) with a height of 9.5 mm.
The built-in G-Sensor gives protection to the system and hard disk (the G-Sensor
does not function with Solid State Drives) in the event that the computer is accidentally dropped when the system is powered on (40cm drop approved when the sys-
tem is powered on and 120cm drop approved when the system is powered off).
Press the Menu button (or double-click the Pop Menu icon in the taskbar) to
bring up the on-screen menu and use the stylus pen to toggle the G-Sensor mode ON
or Off . See “G-Sensor - Hard Disk Drive Protection” on page 1 - 20
for more details.
2 - 2 Hard Disk Drive/Solid State Drive
Features & Components
5-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s).
• MMC (MultiMedia Card)
• SD (Secure Digital)
*Note: The PC adapters are usually supplied with these cards.
• Mini SD (requires PC adapter*)
• SDIO (requires PC adapter*)
• RS MMC (requires PC adapter*)
1
2
Card Reader Cover
Make sure you keep
card reader cover
closed when not in use.
This will help prevent
foreign objects and/or
dust getting in to the
card reader.
Figure 2 - 1
Right View
1. Card Reader
Cover
2. Card Reader
2
5-in-1 Card Reader 2 - 3
Features & Components
2
Make sure you keep
card reader cover
closed when not in use.
This will help prevent
foreign objects and/or
dust getting in to the
card reader.
ExpressCard
Slot Cover
Figure 2 - 2
Right View
1. Card Reader
Cover
2. ExpressCard
Slot
ExpressCard Slot
The computer is equipped with an ExpressCard 34 slot. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver
ExpressCard
Support
1
2
There is a list of approved
ExpressCard modules
listed on Table E - 1, on
page E - 1 Please make
sure any ExpressCards
modules you use with this
computer are included in
the list. Contact your service center for further information.
Inserting and Removing ExpressCards
• Align the ExpressCard with the slot and push it in until it locks into place.
• To remove an ExpressCard, simply press the card to eject it.
2 - 4 ExpressCard Slot
Features & Components
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/
control panel (right-click the taskbar icon to bring up an audio menu). The volume
may be adjusted by means of the On-Screen Menu buttons or the volume icon in
the taskbar (see sidebar).
Right-click the icon
to access the menu
above.
Sound Volume
Adjustment
The sound volume level
is set using the volume
control within Windows
(and the volume function keys on the computer). Click the volume
icon in the taskbar to
check the setting.
Figure 2 - 3
Realtek Audio
Manager
2
Audio Features 2 - 5
Features & Components
2
Tablet PC Options
Chapter 1 contains basic information on calibration (see “Calibrating the Touch
Panel” on page 1 - 11), pen options and tablet settings (see “Pen Options & Tablet
Settings” on page 1 - 1 3) and the On-Screen keyboard (see “ On-Screen Keyboard”
on page 1 - 14). The following pages will add some more de tailed information on
Tablet PC input and settings.
2 - 6 Tablet PC Options
Features & Components
Screen Orientation
If you prefer to orientate the screen differently follow these steps.
Screen Orientation - Windows Control Panel
1. Click Start, and click Control Panel (or point to Settings and click Control
Panel).
2. Click Mobile PC (or just double-click Tablet PC Settings) and then click Tablet
PC Settings.
3. Click Display (tab) and select the orientation required.
4. Click Apply.
5. It is advisable to calibrate the touch panel after rotating the screen (see page
1 - 11
2
).
Figure 2 - 4
Tablet PC Settings
(Display)
Tablet PC Options 2 - 7
Features & Components
Screen Orientation - Intel GMA Control Panel
2
1. Open the Display Settings control panel (see “Video Features” on page 1 - 26 )
and click Advanced Settings (button).
2. Click the Intel(R)... tab and click Graphics Properties (button).
3. Go to the Intel GMA control panel (see “Video Features” on page 1 - 26) and
click Display Settings.
4. Make sure Enable Rotation is ticked and choose the degree of rotation.
5. Click Apply and OK to confirm the setting change.
6. It is advisable to calibrate the touch panel after rotating the screen (see page 1 -
11).
Figure 2 - 5
Intel GMA Display
Settings (Rotation)
2 - 8 Tablet PC Options
Touch Package Settings
You can also configure the pen options from the Touch Package control panel.
Features & Components
2
1. Double-click the Touch tool utility icon on the desktop OR from the Touch
Package folder in the Programs/All Programs group (the driver must be
installed).
2. Click Mouse Emulation.
3. Double-click either Drawing Mode or Button Mode to configure the Right-Click
or Double-Click settings (you can also disable touch altogether if you prefer).
Other Tools
The Touch Package
Touch Tool utility also
allows you to configure
Sound options (for
when you touch and lift
up the stylus pen) and
gives you quick access
to system information
(Advance > System In-
formation Tool).
Figure 2 - 6
Touch Package
Mouse Emulation
Tablet PC Options 2 - 9
Features & Components
Pen and Input Devices
2
You can configure the pen options from the Pen and Input Devices control panel.
1. Click Start, and click Control Panel (or point to Settings and click Control
Panel).
2. Click Mobile PC (or just double-click Pen and Input Devices) and then click Pen
and Input Devices.
3. Select the Pen action from the left menu and click Settings to configure the
setting.
4. You can select the sensitivity of the double-tap speed and distance, the sensitivity
and duration of press and hold (for right-clicking) , and you can test the settings
from this menu.
Figure 2 - 7
Double Tap & Press
and Hold Settings
2 - 10 Tablet PC Options
Features & Components
Other Useful Windows Vista Features for Tablet PC Users
Multi-Select Files in Windows Explorer
The option to multi-select files in Windows Explorer in Windows Vista is very
useful when using a pen as your input device.
2
1. Click
2. Click Appearance and Personalization and click Folder Options (or just
3. Click View (tab), and make sure Use check boxes to select items is ticked.
4. Click OK to save the setting.
5. Check boxes will appear in open folders to allow you to easily multi-select files with
Start
, and click
double-click Folder Options).
a pen.
Control Panel
(or point to
Settings
and click
Control Panel
Tablet PC Options 2 - 11
).
Figure 2 - 8
Folder Options
&
Multi-Select Files
Features & Components
2
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
Parallel Printer
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most current printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instructions (unp acking, p aper tray, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar,
however you will need to purchase a parallel to USB converter.
2 - 12 Adding a Printer
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
• The Po wer So urces
• Turning on the Computer
• Power Plans
• Power-Saving States
• Configuring the Power Buttons
• Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
Hibernate Mode In
Windows Vista SP1
If you are using Windows Vista SP1 with
4GB RAM installed, see
page 7 - 10 for information on Hibernate.
3
Overview 3 - 1
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach th e AC/DC adapter to the DC-in jack on the left of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3. Press the power button and then release it to turn the computer “on”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 14).
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on press the po wer button and release it.
When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when you press and release it in less than 4 seconds (pressing the power
button without releasing it for longer than this will force the computer to shut down).
Use Power Options (Hardware and Sound menu) control panel in Windows Vista
to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination on an attached keyboard
doesn’t work, press and hold the power button for 4 seconds, or longer, to force the system
to turn itself off.
Power Button Sleep
Sleep is the default power mode when the power button is pr essed and released in less
than 4 seconds. You may configure the options for the power button from the Power Options (Hardware and Sound menu) control panel in Windows Vista (see your OS’s doc-
umentation, or “Configuring the Power Buttons” on page 3 - 8 for details).
Power Management
Shut Down
Note that you should always shut your computer down by choosing the
Shut Down command
from the Lock Button
Menu in Windows Vis-
ta. This will help prevent
hard disk or system
problems.
3
Turning on the Computer 3 - 3
Power Management
Power Plans
3
Resuming
Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 1
Power Plan -
Advanced Settings
The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
3 - 4 Power Plans
Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Video Files
If you are playing video files (e.g. mpeg
files) on the computer, it is recommended
that you choose the
High Performance
power plan.
Power Management
Intel GMA Driver
Power Settings
Use the Power Settings control to allow
the Intel(R) GMA Driver
for ultra mobile control
panel to adjust the power options when the
computer is running on
battery power (see
“Power Settings” on
page B - 5).
Figure 3 - 2
Power Plans
3
Power Plans3-5
Power Management
Power-Saving States
3
Power Button
The Power Button in
the Start Menu (in Classic View use the Shut
Down button ) can be
used to send the computer into a power-saving state.
Sleep Mode &
Mobile PC Battery
A mobile PC in Sleep
uses very little battery
power.
After an extended period of time the computer
will save any open documents and applications
to hard disk.
You can use power-saving states to stop the computer’s operation and restart where
you left off. Sleep is the default power-saving state in Windows Vista.
Earlier versions of Windows used Stand By and Hibernate as system power-saving
states. Windows Vista combines the features of Stand By and Hibernate into the default Sleep power-saving state.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
3 - 6 Power-Saving States
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.
Shut Down
You should shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from shut down takes longer than
from Sleep or Hibernate.
Power Management
3
Figure 3 - 3
Lock Button menu
Power-Saving States 3 - 7
Power Management
Configuring the Power Buttons
3
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 4
Power Options
Define Power
Buttons
The power button, sleep button (on any attached keyboard) or Sleep command from
the Lock Button Menu in Windows Vista may be set to send the computer in to a
power-saving state.
3 - 8 Configuring the Power Buttons
Resuming Operation
You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button on an attached keyboard.
Power Management
3
Power Status
Power Off Off Press the Power Button
Sleep Blinking Green
Hibernate
Display Turned Off Green Move any attached Mouse//Touch the Screen
Icon Color
Press the Sleep Button on any attached
Off (battery)
Orange (AC/DC adapter)
To Resume
Press the Power Button
keyboard
Press the Power Button
Power Button
When the computer is on, you can use the power button a s a Sleep/Hi berna te/Sh ut Down
hot key button when it is pressed and released in less than 4 seconds (pressing the power
button for longer than this will force the computer to shut down).
Configuring the Power Buttons 3 - 9
Table 3 - 1
Resuming
Operation
Power Management
Battery Information
3
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings
Please follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge
status.
3 - 10 Battery Information
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth or communication applications when they are not
being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel
provides an easy point
of access for information
on battery status, power
plans used etc.
Figure 3 - 6
Windows Mobility
Center
3
Battery Information 3 - 11
Power Management
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
3
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 1 - 30.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 14 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 16 for information on the battery charge status, and to “Battery
Information” on page 3 - 10 for more information on how to maintain and properly
recharge the battery pack.)
3 - 12 Battery Information
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Power Management
Caution
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
3
Battery Information 3 - 13
Power Management
Battery FAQ
How do I completely discharge the battery?
3
Figure 3 - 7
Power Plan - Create
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all th e options to Never.
3. Click Change plan settings (after saving it) and click Change advanced power
settings.
3 - 14 Battery Information
4. Scroll down to Battery and click + to expand the battery options.
5. Choose the options below (click Yes if a warning appears).
• Low battery levels = 0%
• Critical battery Levels = 0%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
Power Management
3
Figure 3 - 8
Power Options
Advanced Settings -
Battery
Battery Information 3 - 15
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
Battery Gauge
The battery gauge at the rear of the computer provides a clear indication of remaining battery life. Firmly press the PUSH CHECK button and the Led will show the
current battery level.
Figure 3 - 9
Battery Capacity
Gauge
3 - 16 Battery Information
Battery Indicators
On-screen indicators will display the battery status if the battery level button
is pressed or the AC/DC adapter is not connected.
Action Icon Description
Power Management
3
The on-screen
battery level
button is pressed.
AC/DC Adapter
Connection
Removed
Main Battery Level Indicator
Bridge Battery Level Indicator
Main Battery Level is Under 3%
Plug-in the AC/DC Adapter
Main Battery Level is Under 3%
Change Battery
Table 3 - 1
On-Screen Battery
Indicators
Battery Information 3 - 17
Power Management
3
3-18
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities.
Note: For Windows XP driver installation information
see “Driver Installation” on page D - 32.
What to Install
You will need to attach a CD/DVD drive to the computer in order to access the drivers on the Device Driv-
ers & Utilities + User’s Manual disc. This contains
the drivers and utilities necessary for the proper operation of the computer.
Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in-
stalled in the order indicated.
Module Driver Installation
The procedures for installing drivers for the Wireless
LAN, PC Camera and Fingerprint modules are pro-
vided in “Modules” on page 6 - 1.
Note: The operating system is the default setting for
Bluetooth control in Windows Vista, and does not re-
quire a driver. See “Bluetooth Module” on page 6 - 2
for configuration instructions.
4
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the optional driver menu.
4
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the dri ve r s mus t be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, after
installing each driver it will become grayed out (if
you need to reinstall any driver, click the Unlock
button).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Drivers & Utilities
Vista (SP1) Driver Page #
Chipset Page 4 - 5
Video Page 4 - 5
LAN Page 4 - 5
Touch Panel Application Page 4 - 6
Pop Menu Utility Page 4 - 6
Audio Page 4 - 6
Wireless LAN Module Page 6 - 6
PC Camera Module Page 6 - 11
Fingerprint Reader Module Page 6 - 17
Table 4 - 1 - Driver Installation
Manual Driver Installation
Click Browse CD (button) in the Drivers Installer ap-
plication and browse to the executable file in the appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -
6 for instructions.
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1
(or a Windows Vista version which includes Service
Pack 1) before installing any drivers. Go to the Microsoft website for download details, or contact your service
center.
4
Driver Installation 4 - 3
Drivers & Utilities
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
4
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as
outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Double-click Device Manager (Hardware and
Sound > Device Manager).
3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
User Account Control (Win Vista)
If a User Account Control prompt appears as part of
the driver installation procedure, click Continue/Al-
low, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the in-
stallation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installation procedure (other than when outlined in the
driver install procedure), click Cancel to close the
window, and follow the installation procedure.
4 - 4 Driver Installation
Drivers & Utilities
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc into your attached CD/DVD drive and click In-
stall Drivers (button), or Option Drivers (button) to
access the optional driver menu.
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so
the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish)
unless you are an advanced user. In many cases a restart is required to install the driver.
Chipset
1. Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish.
4
Video
1. Click 2.Install Video Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
LAN
1. Click 3.Install LAN Driver > Yes.
2. Click Next > Install.
3. Click Finish.
4. The network settings can now be configured.
Driver Installation 4 - 5
Drivers & Utilities
Touch Panel Application
1. Click 4.Install Touch Panel Driver > Yes.
2. Click Next > Next > Install.
3. Click Finish.
4. Click OK to restart the computer.
4
5. You will then need to calibrate the touch panel
(see “Calibrating the Touch Panel” on page 1
- 11).
Pop Menu Utility
1. Click 5.Install POP Menu Utility > Yes.
2. Click Next > Install.
3. Click Finish > Finish to restart the computer.
4. See “On-Screen Menu” on page 1 - 18 for
details.
Audio
1. Click 6.Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer .
Windows Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes
from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1. Click Start, and click Control Panel (or point
to Settings and click Control Panel).
2. Click Check for updates (Security), or
double-click Security Center and click
Windows Update.
3. Double-click Check for updates (button).
4. The computer will now check for updates
(you need to be connected to the internet).
5. Click Install now (button) to install the
updates.
4 - 6 Driver Installation
Drivers & Utilities
Optional Drivers
See the pages indicated overleaf for the driver installation procedures for any modules included in your purchase option.
Figure 4 - 3 - Optional Drivers
Bluetooth Module
Note: The operating system is the default setting for
Bluetooth control in Windows Vista, and does not re-
quire a driver. See “Bluetooth Module” on page 6 - 2
for configuration instructions.
4
Wireless LAN Module
See the introduction in “Wireless LAN Module” on
page 6 - 6, and check the installation procedure.
PC Camera Module
See the introduction in “PC Camera Module” on
page 6 - 11, and check the installation procedure.
Fingerprint Reader Module
See the introduction in “Fingerprint Reader Module”
on page 6 - 17, and check the installation procedure.
Driver Installation 4 - 7
Drivers & Utilities
4
4-8
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
Note that you will need to attach a USB keyboard to one of the USB ports in
order to edit the BIOS settings.
If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities
Phoenix TrustedCore(tm) NB
Copyright 1985-2006 Phoenix Technologies Ltd.
All Rights Reserved
Bios Revision: ********
KBC/EC Firmware Revision: ********
CPU=1Processors Detected
Intel(R) Atom(TM) CPU Z250 @ 1.33GHz
1015M System RAM Passed
512KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: TOSHIBA MK1246GSX
Mouse intialized
Press <F2> to enter SETUP
The Power-On Self Test (POST)
POST Screen
1.BIOS information
2.CPU type
3.Memory status
5
4.Enter Setup prompt
appears only during
POST
Note:
The
POST
screen
as pictured right is for
guideline purposes only.
POST
The
your computer may appear slightly different. If
you disable the
time Diagnostic Screen
(see page 5 - 9
POST screen will not appear.
screen on
Boot-
), the
Figure 5 - 1
POST Screen
Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
1
2
3
4
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
• Press <F1> to resume
• <F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
BIOS Utilities
5
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
The Setup Program
The Phoenix Setup program tells the system how to configure itself and manage ba-
sic features and subsystems (e.g. port configuration).
Note that you will need to attach a USB keyboard to one of the USB ports in
order to edit the BIOS settings.
5
5 - 4 The Setup Program
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt
(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds
after you turn on the system. If you get a “Keyboard Error”, (usually because you
pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with menu headings. When you select a
heading, a new screen appears. Scroll through the features listed on each screen to
make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
BIOS Utilities
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
5
The Setup Program 5 - 5
BIOS Utilities
Main Advanced Security Boot Exit
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
<Tab>, <Shift Tab>, or
<Enter> selects field.
Main
System Time: [22:12:05]
System Date: [04/24/2009]
Large Disk Access Mode: [DOS]
Primary Master [TOSHIBA MK1246GSX-(P]
Primary Slave [None]
System Memory 640 KB
Extended Memory 1014 MB
BIOS Revision ********
KBC/EC Firmware Revision ********
Phoenix SecureCore(tm) Setup Utility
Main Menu
Figure 5 - 2
Main Menu
5
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
5-6Main Menu
Large Disk Access Mode (Main Menu)
This refers to the representation of hard disk drive geometries as addressed by different operating systems. Select “Other” if you are using systems such as Novell,
UNIX etc. Select “DOS” (default) if you are using Windows.
Primary Master/ Primary Slave (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a HDD/optical device on the computer’s Primary Master/Primary Slave channels is applicable. Use
the Auto (Type:) setting to have the items configured automatically for you.
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities
Advanced Menu
Figure 5 - 3
Advanced Menu
5
Main AAdvanced Security Boot Exit
Installed O/S: [WinXP/Vista]
Reset Configuration Data: [No]
Boot-time Diagnostic Screen: [Disabled]
POST Boot Sound [Disabled]
Battery Low Alarm Beep: [Disabled]
Hyperthreading: [Enabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Advanced
Phoenix SecureCore(tm) Setup Utility
Item Specific Help
Select the operating
system installed on
your system which you
will use most
commonly.
Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.
Installed O/S (Advanced Menu)
This setting tells the computer what kind of operating system you’re using. Make
sure you choose the correct setting for your O/S in order to prevent system pro blems.
5 - 8 Advanced Menu
Reset Configuration Data (Advanced Menu)
This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious
system conflict that the operating system is unable to boot.
Boot-time Diagnostic Screen (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen (see Figure
5 - 1 on page 5 - 2).
POST Beep Sound (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
Hyperthreading (Advanced Menu)
Hyperthreading will increase performance of your computer, depending on the hardware and software you use, by activating additional CPU threads. Make sure your
OS supports Hyperthreading if you are installing a non-Windows OS.
BIOS Utilities
5
Advanced Menu 5 - 9
BIOS Utilities
t
e
u
p
D
b
b
D
b
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
5
access to your machine as it boots up after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
Figure 5 - 4
Security Menu
Main Advanced SSeeccuurriittyyBoot Exit
=
Supervisor Password Is: Clear
User Password Is: Clear
Set Supervisor Password [Enter]
Set User Password [
Diskette access: [
Virus check reminder: [
System backup reminder: [
Password on boot: [
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Set Supervisor Password (Security Menu)
You can set a password for access to the PhoenixBIOS Setup Utility. This will not
affect access to the computer OS, (only the PhoenixBIOS Setup Utility).
Phoenix SecureCore(tm) Setup Utility
Security
e
so
]
]
s
]
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Security Menu
5 - 10 Security Menu
Loading...