EUROCOM Notebook V11.6.00 User Manual

V11.6.00

I

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©June 2011

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

II

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc­tive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux­embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov­enia.

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has at­tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas mo st q uality marking s are voluntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference.
And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

IV

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-l ocated or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environ ment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.

V

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -

240V, 50 - 60Hz DC Output 20V, 15A (300W) minimum).

This Computer’s Optical Device is a Laser Class 1 Product

VI

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overhe at it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.

Do not expose the computer
to any shock or vibration.

Do not place it on an unstable
surface.

Do not place anything heavy
on the computer.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or stor e the computer

in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g proc edur es for t he computer. Sh ut the comp uter down p roper ly and don ’t forge t

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

5. Take care when using peripheral devices.

Do not turn off the power until
you properly shut down all pro­grams.

Do not turn off any peripheral
devices when the computer is
on.

Do not disassemble the com­puter by yourself.

Perform routine maintenance
on your computer.

Use only approved brands of
peripherals.

Unplug the power cord befor e
attaching peripheral devices.

VIII

Preface

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC ada pter may be design ed for inte rnational travel but it still re quires a steady,
uninterrupted power supply. If you are unsure of your local power specifications, consult
your service representative or local power company.

• The power adapter may have either a 2-pr ong or a 3-prong grou nded plug. The third prong
is an important safety feature; do not defeat its purpose. If you do not have access to a
compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord , be sure to disconnect it by the plug head, not by
its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load
of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power sup­plies (i.e. AC/DC adapter or car adapter).

Do not plug in the power
cord if you ar e wet.

Do not use the power cord if
it is broken.

Do not place heavy objects
on the power cord.



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon­nected all peripherals
and cables (including
telephone lines). It is
advisable to also re­move your battery in
order to prevent acci­dentally turning the
machine on.

IX

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansio n or swelling, however this is part of the battery’s safety mecha­nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera­ture environments, and do not store unused batteries for extended per iods.

See also the general battery precautionary information overleaf for further information.

X

Preface

General Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replac ement to your service repre sent ative or qual­ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Bat teries
may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.

XI

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.

XII

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapte r. However ,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or r equire proof of ownersh ip for both ha rd-

ware and software. Make sure your “papers” are handy.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. T o prevent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

XIII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.

XIV

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods o f time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Y our knees sho uld be sligh tly high er than your h ips. Place yo ur feet flat on the floor or on
a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.

XV

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

Cable TV Safety

If you have included a TV Tuner in your purchase option then pay careful attention to the following:

• Make sure that your CATV system installer has connected the Coaxial cable shield to the grounding system of the
building, as close to the point of cable entry as practical.

• This reminder is provided to call the CATV system installer’s attention to Article 820-93 of the NEC (Section 54, Part
I of the Canadian Electrical Code).

• The TV antenna supplied with any TV Tuner module is intended for indoor use only. Please do not use your TV Tuner
module outdoors.

XVI

Preface

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your service center.

XVII

Preface

Contents

Notice .................................................................................I

FCC Statement ................................................................III

FCC RF Radiation Exposure Statement: ........................IV

Instructions for Care and Operation ...............................VI

Power Safety ................................................................ VIII

Polymer Battery Precautions ..........................................IX

General Battery Precautions ............................................X

Cleaning .......................................................................... XI

Servicing .........................................................................XI

Travel Considerations ....................................................XII

Quick Start Guide

Overview ........................................................................1-1

Advanced Users .............................................................1-2

Beginners and Not-So-Advanced Users ........................1-2

Warning Boxes ............................................ ..................1-2

Not Included .................................................................. 1-3

System Software ...................................................... .... ..1-4

RAID & AHCI Setup .....................................................1-4

System Startup ...............................................................1-5

System Map: LCD Panel Open & Top View ................1-6

LED Indicators ...............................................................1-7

Touch Sensor Instant Keys ............................................1-8

Keyboard ........................................................................1-9

Function Keys & Visual Indicators .............................1-10

System Map: Front & Rear Views ...............................1-11

System Map: Right View .............................................1-12

System Map: Left View ...............................................1-13

System Map: Bottom View ..........................................1-15

Windows 7 Start Menu & Control Panel .....................1-16

Video Features .............................................................1-17

Screen Resolution ........................................................1-18

NVIDIA Control Panel ................................................1-19

Catalyst Control Center ...............................................1-20

Power Options ........................................ ......................1-21

Storage Devices, Mouse, Audio &
Printer

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

Optical Device ...............................................................2-3

Loading Discs ................................................................2-3

Handling CDs or DVDs .................................................2-4

DVD Regional Codes ....................................................2-5

Multi-In-1 Card Reader .................................................2-6

ExpressCard Slot ............................................................2-7

XVIII

Preface

Inserting and Removing ExpressCards ..........................2-7

Audio Features ...............................................................2-8

Setup for Audio Recording ............................................2-9

Setup for 5.1 or 7.1 Surround Sound ...........................2-10

Dolby Settings .............................................................2-12

HDMI Audio Configuration ........................................2-13

Audio Setup for LCD Monitors/

TVs with HDMI Input .................................................2-14

TouchPad and Buttons/Mouse .....................................2-16

Gestures and Device Settings ......................................2-18

Adding a Printer ...........................................................2-21

USB Printer ..................................................................2-21

Install Instructions: ......................................................2-21

Parallel Printer .............................................................2-21

Power Management

Overview ........................................................................3-1

The Power Sources ........................................................3-2

AC/DC Adapter .............................................................3-2

Battery ............................................................................3-2

Turning On the Computer .............................................. 3-3

Power Plans ...................................................................3-4

Power-Saving States ......................................................3-6

Sleep ..............................................................................3-6

Hibernate ........................................................................3-7

Shut down ......................................................................3-7

Configuring the Power Buttons .....................................3-8

Resuming Operation ......................................................3-9

Battery Information ......................................................3-10

Conserving Battery Power ...........................................3-11

Battery Life ..................................................................3-12

New Battery .................................................................3-12

Recharging the Battery with the AC/DC Adapter .......3-12

Proper handling of the Battery Pack ............................3-13

Battery FAQ .................................................................3-14

Drivers & Utilities

RAID & AHCI Setup .....................................................4-1

What to Install ................................................................4-1

Module Driver Installation ............................................. 4-1

Driver Installation ..........................................................4-2

Manual Driver Installation .............................................4-4

Updating/Reinstalling Individual Drivers ......................4-4

User Account Control ....................................................4-5

Windows Security Message ...........................................4-5

New Hardware Found ....................................................4-5

Driver Installation Procedure ......................................... 4-6

Chipset ...........................................................................4-7

Video (NVIDIA) ............................................................4-7

Video (AMD) .................................................................4-7

XIX

Preface

LAN ...............................................................................4-7

Card Reader ...................................................................4-7

TouchPad .......................................................................4-8

USB 3.0 ..........................................................................4-8

Hot Key ..........................................................................4-8

Audio .............................................................................4-8

Windows Experience Index ...........................................4-9

Optional Drivers ..........................................................4-10

Wireless LAN ..............................................................4-10

PC Camera ...................................................................4-11

Consumer Infrared (for TV Tuner Remote) ................4-11

Security Modules (Fingerprint & TPM) ......................4-11

BIOS Utilities

Overview ........................................................................5-1

The Power-On Self Test (POST) ................................... 5-2

Failing the POST ........................................................... 5-3

Fatal Errors ....................................................................5-3

Non-Fatal Errors ............................................................5-3

The Setup Utility ............................................................5-4

Entering Setup ...............................................................5-4

Setup Screens .................................................................5-5

Main Menu .....................................................................5-6

System Time & Date (Main Menu) ...............................5-6

System/Extended Memory: (Main Menu) .....................5-7

BIOS Revision/VGA Card etc. (Main Menu) ............... 5 -7

Advanced Menu .............................................................5-8

Advanced Chipset Control (Advanced Menu) ...............5-8

SATA Mode Selection (Advanced Menu) .....................5-9

Legacy USB Support: (Advanced Menu) ......................5-9

Boot-time Diagnostic Screen: (Advanced Menu) ..........5-9

Reset Configuration Data (Advanced Menu) ................5-9

Power On Boot Beep (Advanced Menu) .....................5-10

Battery Low Alarm Beep: (Advanced Menu) ..............5-10

Advanced Chipset Control Menu ................................5-11

Bluetooth Power Setting >

Advanced Chipset Control ........................................... 5-11

Intel Virtualization Technology >

Advanced Chipset Control ........................................... 5-12

Hyperthreading > Advanced Chipset Control .............5-12

CPU C State > Advanced Chipset Control ..................5-12

Turbo Boost > Advanced Chipset Control ..................5-12

Security Menu ..............................................................5-13

Set Supervisor Password (Security Menu) ..................5-13

Set User Password (Security Menu) ............................5-14

Password on boot (Security Menu) ..............................5-14

TPM State ....................................................................5-15

Change TPM State (TPM State) ..................................5-15

Boot Menu ...................................................................5-17

Exit Menu ....................................................................5-18

XX

Preface

Upgrading The Computer

Overview ........................................................................6-1

When Not to Upgrade ....................................................6-2

Removing the Battery ....................................................6-3

Upgrading the Hard Disk Drive(s) ................................6-4

Upgrading the Optical (CD/DVD) Device ..................6-13

Upgrading the System Memory (RAM) ......................6-14

Modules

Overview ........................................................................7-1

Setting Up SATA RAID Mode ......................................7-2

AHCI Mode ...................................................................7-2

RAID ..............................................................................7-2

Intel® Rapid Storage Technology Application .............7-2

SATA RAID Setup Procedure (BIOS) ..........................7-4

RAID Setup (Intel Matrix) .............................................7-5

Intel Rapid Storage Technology ....................................7-8

IRST Driver Installation ................................................7-8

RAID Volume Data Verification and Repair ..............7-10

Replacing and Reverting Recovery and

Master Volumes ...........................................................7-10

RAID Volume Data Verification and Repair ..............7-12

Replacing and Reverting Recovery and

Master Volumes ...........................................................7-12

Wireless LAN Module .................................................7-15

Intel® Wi-Fi Link Series Driver Installation ...............7-16

802.11b/g/n Driver Installation ....................................7-16

Connecting to a Wireless Network in Windows 7 .......7-17

Intel® My WiFi Configuration ....................................7-20

Windows Mobility Center ...........................................7-32

PC Camera Module ......................................................7-33

PC Camera Driver Installation .....................................7-34

PC Camera Audio Setup ..............................................7-35

TV Tuner Module ........................................................7-41

Consumer Infrared Driver ............................................7-42

Digital TV Broadcast Signal ........................................7-43

TV Recording and Power Plans ...................................7-43

Remote Control Unit ....................................................7-43

Bluetooth Module ........................................................7-44

3rd Party Bluetooth Combo Driver Installation ........... 7-46

3rd Party Bluetooth & WLAN Combo Settings ..........7-47

Bluetooth Networking Setup .......................................7-50

Bluetooth & WLAN Combo Module Configuration ...7-51

Intel Bluetooth Combo Driver Installation ..................7-54

Bluetooth Configuration in Windows 7 .......................7-55

Security Modules (Fingerprint & TPM) ......................7-59

Fingerprint Reader Module ..........................................7-60

Fingerprint Reader Driver Installation .........................7-60

User Enrollment ...........................................................7-61

Fingerprint Control Center Features ............................7-64

XXI

Preface

Trusted Platform Module .............................................7-65

Enabling & Activating TPM ........................................7-65

Trusted Platform Module (TPM) Driver Installation ..7-67

Initializing TPM ...........................................................7-67

Infineon Security Platform Settings Tool ....................7-70

Troubleshooting

Overview ........................................................................8-1

Basic Hints and Tips ......................................................8-2

Backup and General Maintenance .................................8-3

Viruses ...........................................................................8-4

Upgrading and Adding New Hardware/Software ..........8-5

Problems & Possible Solutions ...................................... 8-7

Bluetooth Connection Problems ..................................8-15

Intel® WLAN & Bluetooth V3.0+HS

Combo Modules ...........................................................8-19

Interface (Ports & Jacks)

Overview .......................................................................A-1

Ports and Jacks ..............................................................A-2

Card Reader ..................................................................A-2

Cable (CATV) ..............................................................A-2

Antenna Jack .................................................................A-2

Consumer Infrared Transceiver ....................................A-2

DC-In Jack ....................................................................A-2

DVI-Out Port ................................................................A-2

e-SATA Port .................................................................A-3

HDMI-Out Port .............................................................A-3

Headphone-Out Jack .....................................................A-3

Line-In Jack ..................................................................A-3

Microphone-In Jack ......................................................A-3

Mini-IEEE 1394b Port ..................................................A-4

RJ-45 LAN Jack ............................................................A-4

S/PDIF-Out Jack ...........................................................A-4

Security Lock Slot ........................................................A-4

USB 2.0/1.1 Ports .........................................................A-5

USB 3.0 Port .................................................................A-5

NVIDIA Video Driver Controls

NVIDIA Video Driver Installation ...............................B-1

NVIDIA Control Panel (Win 7) ....................................B-2

Display Devices ............................................................B-5

Display Modes ..............................................................B-6

Attaching Other Displays (Win 7) ..............................B-11

SLI Multi GPU Configuration ....................................B-14

SLI Multi GPU Configuration & Battery Power ........ B-15

Enabling TV Display ..................................................B-16

XXII

Preface

AMD Video Driver Controls

Video Driver Installation ..............................................C-1

Video (VGA) C-1

Catalyst™ Control Center ............................................C-2

Catalyst™ Control Center Preferences C-3

Display Devices & Options ..........................................C-7

Configuring an External Display In the CCC ............... C-8

Configuring an External Display In Windows 7 ....... C-12

HDMI Audio Configuration .......................................C-17

Specifications

Processor ....................................................................... D-2

Core Logic ................................................................... .D-2

Display .......................................................................... D-2

Memory .........................................................................D-2

Video Adapter Options .................................................D-2

Video Adapter Options .................................................D-2

Video Adapter Options .................................................D-3

Video Adapter Options .................................................D-3

Video Adapter Options .................................................D-3

BIOS .............................................................................D-3

Storage ..........................................................................D-4

Audio ............................................................................D-4

Keyboard & Pointing Device ........................................D-4

Slots ..............................................................................D-4

Card Reader ..................................................................D-4

Interface ........................................................................D-4

Communication ............................................................. D-5

Security .........................................................................D-5

Operating System ..........................................................D-5

Power Management .................................................. ....D-5

Power ............................................................................D-5

Environmental Spec ......................................................D-5

Physical Dimensions & Weight .................................... D-5

Overview 1 - 1

Quick Start Guide

1

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, card reader), TouchPad & Mouse, Audio Features & Printer.

• Chapter 3 The computer’s power management options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s RAID, Wireless LAN, PC Camera, TV Tuner, Bluetooth &

WLAN Combo and Security (Fingerprint and TPM) modules (some of which may be optional
depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the NVIDIA Video driver controls.

• Appendix C Information on the AMD Video driver controls.

• Appendix D The computer’s specification.

1 - 2 Overview

Quick Start Guide

1

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”

on page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.



Notes

Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.

Overview 1 - 3

Quick Start Guide

1

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs)
have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers

& Utilities” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to com­municate with external devices, connect to the internet etc.

1 - 4 Overview

Quick Start Guide

1

System Software

Your computer may already come with system software pre-installed. Where this is
not the case, or where you are re-configuring your computer for a different system,
you will find the Windows 7 operating system is supported.

Note: In order to run Windows 7 without limitations or decreased performance, your
computer requires a minimum 1GB of system memory (RAM).

RAID & AHCI Setup

Note that setting up a RAID, or AHCI mode, needs to be done prior to installing the
Windows OS (see “Setting Up SATA RAID Mode” on page 7 - 2).



TV Tuner Module

Support

Note that the TV Tuner
module (factory) option
is supported by the Win-

dows Media Center
software. Windows Me­dia Center is not includ-
ed in Starter or Home
Basic versions of Win-

dows 7.

System Startup 1 - 5

Quick Start Guide

1

System Startup

1. Remove all packing materials, and plac e th e c omp ut er on a stable surf ac e.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to raise the

lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);

use
the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the
computer by the lid/LCD).

5. Raise the lid/LCD to a comfortable viewing angle, and press the power button.

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD



Shutdown

Note that you should always shut your computer down by choos­ing the Shut Down command from the Start menu in Windows 7.
This will help prevent hard disk or system problems.

135

1 - 6 System Map: LCD Panel Open & Top View

Quick Start Guide

1

System Map: LCD Panel Open & Top View

Figure 1 - 2

LCD Panel Open

& Top View

1. Built-In PC Camera

2. Built-In Microphone

3. LCD

4. LED Status Indicators

5. Touch Sensor Instant
Keys

6. Speakers

7. Power Button

8. Keyboard

9. TouchPad and
Buttons

10.Fingerprint Reader
Module

11. LCD Panel Color
LED

11

3

1

8

9

7

4



Wireless Device

Operation Aboard

Aircraft

The use of any portable elec­tronic transmission devices (e.g.
WLAN or Bluetooth) aboard air­craft is usually prohibited. Make
sure any wireless modules are
OFF if you are using the comput­er aboard aircraft.

Use the appropriate function key
combination to toggle power to
any wireless modules, and
check the indicators to see if any
modules are powered on or not
(see Table 1 - 3, on page 1 - 8).

6 6

66

5

4

5

5

22

10

6

Quick Start Guide

System Map: LCD Panel Open & Top View 1 - 7

1

LED Indicators

The LED indicators display helpful information about
the current status of the computer.

Table 1 - 1 - LED Status Indicators

Table 1 - 2 - LED Power Indicators

Icon Color Description

Blue Scroll Lock is Activated

Blue Caps Lock is Activated

Blue Number Lock is Activated

Blinking Blue Hard Disk Activity

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking

Green

The Computer is In Sleep Mode

Orange The Battery is Charging

Blinking

Orange

The Battery has Reached

Critically Low Power Status

Green The Battery is Fully Charged

Quick Start Guide

1 - 8 Touch Sensor Instant Keys

1

Touch Sensor Instant Keys

Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module
is powered on the appropriate icon will be highlighted blue.

Table 1 - 3 - Touch Sensor Instant Keys

Note that you can also use the function key combinations for all of the functions above (see page 1 - 10).

Icon Description

Mute Toggle

Bluetooth Module (optional) Power Toggle

Wireless LAN Module (optional) Power Toggle

PC Camera Module Power Toggle

Volume Control (Press and hold your finger at either end

/ of the volume control

to adjust the system volume)

Keyboard 1 - 9

Quick Start Guide

1

Keyboard

The keyboard has an embedded numerical keypad for easy numeric data input, and
features function keys to allow you to change operational features instantly. See

Table 1 - 4, on page 1 - 10 for full function key combination details.

Figure 1 - 3 - Keyboard



Other Keyboards

If your keyboard is dam­aged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it auto­matically. However spe­cial functions/hot-keys
unique to the system’s
regular keyboard may not
work.

Num Lk & Scr Lk

Hold down the Fn Key
and Scr Lk/Num Lk to en­able scroll lock/number
lock, and check the LED
indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk &
ScrLk Keys

Fn Key

Keypad



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.

1 - 10 Keyboard

Quick Start Guide

1

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the
basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is in­stalled (see “Hot Key” on page 4 - 8).

After installing the driver an icon will appear in the taskbar.

Table 1 - 4 - Function Keys & Visual Indicators

Keys Function/Visual Indicators Keys Function/Visual Indicators

Fn + ~ Play/Pause (in Audio/Video Programs) Fn +F8/F9

Brightness Decrease/

Increase

Fn + F1 Touchpad Toggle Fn + F10

PC Camera Power

Toggle

Fn + F2

Turn LCD Backlight Off

(Press a key to or use Touchpad to turn on)

Fn + F11

*WLAN Module

Power Toggle

Fn + F3 Mute Toggle Fn + F12

Bluetooth Module

Power Toggle

Fn + F4 Sleep Toggle Fn + NumLk Number Lock Toggle

Fn +F5/F6

Volume Decrease/

Increase

Fn + ScrLk Scroll Lock Toggle

Fn + F7 Display Toggle - DO NOT use when SLI is enabled Fn + 5

Audio Toggle - Toggle between Stereo and 5.1 Sur-

round Sound Modes

Quick Start Guide

System Map: Front & Rear Views 1 - 11

1

System Map: Front & Rear Views

Figure 1 - 4

Front View

1. ExpressCard Slot
(see page 2 - 7)

2. Consumer Infrared
Transceiver
(enabled with
optional TV Tuner
only)

3. LED Power
Indicators

4. DC-In Jack

5. Vent/Fan Intake

3

4

2

5 5



TV Tuner Module Support

Note that the TV Tuner module (factory) option is supported by the Windows Media Cen­ter software. Windows Media Center is not included in Starter or Home Basic versions

of Windows 7.

5 5

1

1 - 12 System Map: Right View

Quick Start Guide

1

System Map: Right View

Figure 1 - 5

Right View

1. Line-In Jack

2. S/PDIF-Out Jack

3. Microphone-In Jack

4. Headphone-In Jack

5. 3 * USB 2.0 Ports

6. Security Lock Slot

1

5

3 42

6



USB Ports

Note that the connections to the USB ports only fit one way, do not force them.

5 5



USB 2.0 or 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

System Map: Left View 1 - 13

Quick Start Guide

1

System Map: Left View

Figure 1 - 6

Left View

1. Speaker

2. DVI-Out Port

3. Cable (CATV)
Antenna Jack

*

4. RJ-45 LAN Jack

5. HDMI-Out Port

6. 2 * USB 3.0 Ports

7. eSATA Port

8. Mini-IEEE 1394b Port

9. 9-in-1 Card Reader

10. Optical Device Drive
Bay

*Enabled with Optional
Mini-PCI TV Tuner Only



Mini-IEEE 1394b Port

The Mini-IEEE 1394b port
only supports SELF POW-

ERED IEEE 1394 devices.

1

2

3

4

5

9

6

8



USB 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2 .0 ports are colored black. Note that
the USB 3.0 port requires a driver installation (see “USB 3.0” on page 4 - 7), does not
support wake on USB and is not operational under DOS.

9-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible

MS (Memory Stick) / MS Pro / MS Duo

HDMI Ports

Note that the HDMI Ports support video and audio signals to attached external displays
(also see “HDMI Ports” on page 2 - 7).

7

6

10

1 - 14 System Map: Left View

Quick Start Guide

1



Disk Eject Warning

Don’t try to eject a CD/DVD while the system is ac­cessing it. This may cause the system to “crash”. Stop
the disk first then eject it, or press the stop button
twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to
an unexpected power interruption) you may push the
end of a straightened paper clip into the emergency
eject hole. Do not use a sharpened pencil or any ob­ject that may break and become lodged in the hole.
Don’t try to remove a floppy disk/CD/DVD while the
system is accessing it. This may cause the system to
“crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device
Manager (Hardware and Sound), then click th e +

next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dialog
box, and select the DVD Region (tab) to bring up the
control panel to allow you to adjust the regional code.

DVD region detection is device dependent, not OS­dependent. You can select your module’s region
code 5 times. The fifth se lection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.

System Map: Bottom View 1 - 15

Quick Start Guide

1

System Map: Bottom View

Figure 1 - 7

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay
Cover

4. Battery
(Secondary HDD
Bay - HDD3)

5. Primary HDD Bay
(HDD1 & 2)



Overheating

To prevent your comput­er from overheating make
sure nothing blocks the
vent(s)/fan intake(s)
while the computer is in
use.

1

2

4 5



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial dis­charges. See “Battery Information” on page 3 - 10 for full instructions.

3

2 2

1 - 16 Windows 7 Start Menu & Control Panel

Quick Start Guide

1

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac­cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features,
however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all
controls it may be necessary to toggle off Category View to view the control panel icons.

Figure 1 - 8 - Start Menu & Control Panel

Click here to toggle Category View

Video Features 1 - 17

Quick Start Guide

1

Video Features

This computer features two different (either AMD or NVIDIA) video options. You can switch display devices,
and configure display options, from the Display control panel (in Appearances and Personalization) in Win-
dows 7.

To access Display (Control Panel) and Screen Resolution in Windows:

1. Click Start and click Control Panel.

2. Click Display (icon) - In the Appearances and Personalization category.

3. Click Adjust Screen Resolution/Adjust resolution.

OR

4. Alternatively you can right-click the desktop and select Screen resolution (Figure 1 - 9 on page 1 - 18).

5. Use the dropbox to select the screen Resolution (Figure 1 - 9 on page 1 - 18).

1

2



NVIDIA & AMD Video Controls

More detailed video controls are provided by the NVID IA Control Pane l or Catalyst Control Center. For more detailed
information see see “NVIDIA Control Panel” on page 1 - 19/“Catalyst Control Center” on page 1 - 20 and Appendix

B or Appendix C.

You can also access the control panels by right-clicking the de sktop and selecting NVIDIA Control Panel/Catalyst (TM)
Control Center (Figure 1 - 10 on page 1 - 19/Figure 1 - 11 on page 1 - 20).

1 - 18 Video Features

Quick Start Guide

1

Screen Resolution

Figure 1 - 9 - Screen Resolution

2



Video Options

Note that card types, specifica­tions and drivers are subject to
continual updates and changes.
Check with your service center
for the latest details on video
cards supported.

1

Video Features 1 - 19

Quick Start Guide

1

NVIDIA Control Panel

You can access the NVIDIA Control Panel as follows:

1. Click

Start

, and click

Control Panel

.

2. Click NVIDIA Control Panel (Figure 1 - 10) - In the Appearances and Personalization category.

3. See “NVIDIA Video Driver Controls” on page B - 1 for full details on control panels etc.

OR

4. You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel .

Figure 1 - 10 - NVIDIA Control Panel

1

2

2

1

1 - 20 Video Features

Quick Start Guide

1

Catalyst Control Center

You can access the CatalystTM Control Center as follows:

1. Right-click the desktop and select Catalyst Control Center (Figure 1 - 11).
OR

2. Double-click the icon (Figure 1 - 11) in the Windows notification area (or right-click the icon and select
Catalyst Control Center).

3. See “AMD Video Driver Controls” on page C - 1 for full details on control panels etc.

Figure 1 - 11 - Catalyst Control Center Access

1

2

1

Right-Click
for Menu

2

Power Options 1 - 21

Quick Start Guide

1

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change plan settings and click Change advanced power settings to access further con­figuration options.

Pay attention to the instructions on battery care in “Battery Information” on page 3 - 10.

Figure 1 - 12 - Power Options

Quick Start Guide

1 - 22

1

Storage Devices, Mouse, Audio & Printer

Overview 2 - 1

2

Chapter 2: Storage Devices, Mouse, Audio &
Printer

Overview

Read this chapter to learn more about the following main features and components
of the computer:

•Hard Disk Drive

• Optical Device

• Multi-In-1 Card Reader

• ExpressCard Slot

• Audio Features

• HDMI Audio Configuration

• Adding a Printer

Storage Devices, Mouse, Audio & Printer

2 - 2 Hard Disk Drive

2

Hard Disk Drive

The hard disk drive(s) issuer) used to store your data in the computer. The hard
disks) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives
with a height of 9.5 mm. The primary hard disk bay is accessible from the bottom
of your computer as seen below, and the secondary hard disk bay is located under
the battery compartment.

The computer can accommodate up to three hard disks (two in the primary bay, and
one in the secondary bay), and these may be configured in RAID or AHCI modes.
Further details on removing and inserting the hard disk are available in “Upgrading

the Hard Disk Drive(s)” on page 6 - 4.



Power Safety

Before attempting to ac­cess any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the ma­chine is turned off. Also
ensure that all peripher­al cables, including
phone lines, are discon­nected from the comput­er.

Figure 2 - 1

Hard Disk Location

1

2

1

2

Storage Devices, Mouse, Audio & Printer

Optical Device 2 - 3

2

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the model you purchased (see “Storage” on page D - 3). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 15).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt­ed, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.



Sound Volume

Adjustment

How high the sound vol­ume can be set depends
on the setting of the vol­ume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting.

Peripherals must be
connected before you
turn on the system.

Figure 2 - 2

Optical Device

123

1

2

3

Storage Devices, Mouse, Audio & Printer

2 - 4 Optical Device

2

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.



CD Emergency Eject

If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharp­ened pencil or similar
object that may break
and become lodged in
the hole.

Disk Eject Warning

Don’t try to remove a
CD/DVD while the sys­tem is accessing it. This
may cause the system
to “crash”.

Storage Devices, Mouse, Audio & Printer

Optical Device 2 - 5

2

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on

page 1 - 14.

DVD Regional Coding

Region Geographical Location

1 USA, Canada

2

Western Europe, Japan, South

Africa, Middle East & Egypt

3

South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia,

Hong Kong

4

South & Central America, Mexico,

Australia, New Zealand

5

N Korea, Russia, Eastern Europe,

India & Most of Africa

6China

Table 2 - 1

DVD Regional Coding

Storage Devices, Mouse, Audio & Printer

2 - 6 Multi-In-1 Card Reader

2

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the card reader driver (see

“Card Reader” on page 4 - 7).

Note: Some of these cards require PC adapters that are usually supplied with the
cards.



Card Reader Cover

Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust get­ting in to the card read­er.

Figure 2 - 3

Right View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

1

Storage Devices, Mouse, Audio & Printer

ExpressCard Slot 2 - 7

2

ExpressCard Slot

The computer is equipped with an ExpressCard/34 slot that reads Express Card/34
formats. ExpressCards are the successors to PCMCIA (PC Cards).

Inserting and Removing ExpressCards

• Press the cover to eject it before inserting an ExpressCard.

• Align the ExpressCard with the slot and push it in until it locks into place.

• To remove an ExpressCard, simply press the card to eject it.



ExpressCard

Slot Cover

Make sure you keep the
cover in the Express­Card slot when not in
use. This will help pre­vent foreign objects and/
or dust getting in to the
ExpressCard Slot.

Figure 2 - 4

Express Card Slot

1. ExpressCard
Slot

1

Storage Devices, Mouse, Audio & Printer

2 - 8 Audio Features

2

Audio Features

You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/
control panel (right-click the taskbar icon to bring up an audio menu). The volume
may also be adjusted by means of the Fn + F5/F6 key combination or by pressing
your finger on either end of the Touch Sensor volume control (see Table 1 - 3, on

page 1 - 8).



Sound Volume

Adjustment

The sound volume level
is set using the volume
control within Windows
(and the volume func­tion keys on the comput­er). Click the volume
icon in the taskbar to
check the setting.

Figure 2 - 5

Realtek Audio

Manager

Right-click the icon
to access the menu
above.

See “HDMI Audio Configuration” on page 2 - 13 for a description of the audio configuration
when connecting an HDMI supported display device.

Storage Devices, Mouse, Audio & Printer

Audio Features 2 - 9

2

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instruc­tions below:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

)

and make sure you are in

Classic View

.

2. Click Realtek HD Audio Manager (or right-click the taskbar icon and select
Sound Manager).

3. Click Microphone Effects (tab) in Microphone (tab), and th en click to select
Noise Suppression (button), or adjust th e Recording Volume level to around 60,
to obtain the optimum recording quality.

4. Click OK to close the control panel and save the settings.

Figure 2 - 6

Realtek Audio

Manager -

Recording Setup

Storage Devices, Mouse, Audio & Printer

2 - 10 Audio Features

2

Setup for 5.1 or 7.1 Surround Sound

To setup your system for 5.1 or 7.1 surround sound you will need to connect the au­dio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out
jacks (note: the S/PDIF jack is used for 7.1 surround sound only) .

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

)

and make sure you are in

Classic View

.

2. Click Realtek HD Audio Manager (or right-click the taskbar icon and select
Sound Manager).

3. Click Speakers (tab) and click Speaker Configuration (tab).

4. Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.



Fn + 5 Audio Toggle

The Fn + 5 key combi­nation allows you to tog­gle the audio system
between stereo and sur­round modes. The ste­reo mode will allow for a
louder audio volume.

Note that if you have
stereo mode enabled,
and attempt to demo the
speaker configuration,
then the sound will only
be enabled through the
front and rear speakers.

Figure 2 - 7

Speaker

Configuration (7.1)



Auto Popup Dialog

You should enable the
auto popup dialog to au­tomatically detect when a
device has been
plugged-in. If disabled,
double-click connector
settings and click the
box to enable the auto
popup detection of
plugged-n devices.

Connector Settings

Storage Devices, Mouse, Audio & Printer

Audio Features 2 - 11

2

5. Plug the front speaker cables into the Headphone-Out Jack.

6. Plug in the other cables (you may require an adapter to connect each cable to the
appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as
follows:

• Line-In Jack = Rear Speaker Out

• Microphone-In Jack = Center/Subwoofer Speaker Out

• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)

7. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on

page 2 - 10).

8. Click to put a tick in the appropriate box according to the speaker plugged-in (e.g.
Rear Speaker Out), and then click OK to save the setting.

9. Click OK to exit Realtek HD Audio Manager.

Figure 2 - 8

Connected Device

Auto Popup

Note: Side Speaker Out is required fo r 7.1 Surround only.

Storage Devices, Mouse, Audio & Printer

2 - 12 Audio Features

2

Dolby Settings

You can adjust the Dolby settings from the Dolby tab in Speakers Properties.

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2. Click Sound (Hardware and Sound).

3. Click Playback (tab).

4. Double-click Speakers (or select Properties from the right-click menu).

5. Click Dolby (tab)

6. Adjust the settings to your preferences and click OK.

Figure 2 - 9

Speakers Properties

Dolby Settings

Storage Devices, Mouse, Audio & Printer

Audio Features 2 - 13

2

HDMI Audio Configuration

As HDMI (High-Definition Multimedia Interface) carries both audio and video sig­nals you can configure the audio output as per the instructions below.

Audio Setup for HDMI

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2. Click Sound (Hardware and Sound).

3. Click Playback (tab), and click to select Realtek Digital Output.

4. Click Set Default (button).

5. Click OK to close the Sound control panel.

6. Select Speakers as the default for standard audio sources.

Figure 2 - 10

Sound Playback

Options

Storage Devices, Mouse, Audio & Printer

2 - 14 Audio Features

2

Audio Setup for LCD Monitors/TVs with HDMI Input

Some LCD monitors/TVs support HDMI input, but DO NOT have built-in digital
audio decoders. Where this is the case, when playing DVDs in Windows Media
Player/CyberLink Power DVD, a background noise can occur. If this situation does
arise then please follow the instructions below.

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2. Click Sound (Hardware and Sound).

3. Double-click Realtek Digital Output.

4. Click Supported Formats (tab).

5. Click to disable (remove the check in the box) DTS Audio and Dolby Digital.

6. Click OK and close the control panels.

Figure 2 - 11

Sound

Supported Formats

Storage Devices, Mouse, Audio & Printer

Audio Features 2 - 15

2

HDMI Notes

• Connect a device with HDMI support to the HDMI-Out port BEFORE attempt-

ing to play audio/video sources through th e device.

• If you disconnect the HDMI cable the default audio playback device will not

revert to speakers until the computer is restarted (if you do not wish to restart the
computer then go to the Sound control panel and select Speakers as the default
audio playback device).

HDMI Video Configuration

1. Connect an HDMI cable from the HDMI-Out port to your external display.

2. Configure your external display as per the instructions in “Configuring an

External Display using the NVIDIA Control Panel” on page B - 7.

3. Set up your external display (TV or LCD) for HDMI input (see your display device
manual).

4. You can now play video/audio sources through your external display.



Other Applications

If you are using a third
party application to play
DVDs etc. you will need
to consult the applica­tion’s documentation to
see the appropriate au­dio configuration (the
application must support
digital to analog transla­tion).

Storage Devices, Mouse, Audio & Printer

2 - 16 TouchPad and Buttons/Mouse

2

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.



Mouse Driver

If you are using an ex­ternal mouse your op­erating system may be
able to auto-configure
your mouse during its
installation or only en­able its basic functions.
Be sure to check the
device’s user docu­mentation for details.

Storage Devices, Mouse, Audio & Printer

TouchPad and Buttons/Mouse 2 - 17

2

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 8) you
can configure the functions from the Mouse control panel in Windows, or by double­clicking the TouchPad driver icon on the taskbar. You may then configure the
TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your
preferences. You will find further information at www.synaptics.com.



TouchPad Scrolling

This computer model se­ries may feature different
TouchPad versions.

These TouchPads may
differ in their vertical
scrolling function in most
scrollable windows.

Some TouchPads require
sliding the finger up and
down on the right of the
TouchPad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
TouchPad to scroll the
window.

Figure 2 - 12

Mouse Properties

Storage Devices, Mouse, Audio & Printer

2 - 18 TouchPad and Buttons/Mouse

2

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (ac­tion) on the surface of the TouchPad to perform specific actions to manipulate doc­uments, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (t ab) and click Settings.

4. Use the menu tree on the left to access the user configurable settings.



Show Video

You can get a clearer
view of the gestures in­volved by clicking the
Show Video option for
each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Set­tings left tree menu

and click the Show Video
button to see the demon­stration video.

For more details on any of
the gestures see the help
in the lower part of the
right menu window.

Figure 2 - 13

Mouse Properties -

Device Settings

Storage Devices, Mouse, Audio & Printer

TouchPad and Buttons/Mouse 2 - 19

2

Scrolling

The Two-Finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight con­tinuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.

Figure 2 - 14

Scrolling Gesture

Figure 2 - 15

Zooming Gesture

Storage Devices, Mouse, Audio & Printer

2 - 20 TouchPad and Buttons/Mouse

2

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of
applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.

Figure 2 - 16

Rotating Gesture

Figure 2 - 17

Flick/Press

Gesture

Storage Devices, Mouse, Audio & Printer

Adding a Printer 2 - 21

2

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.

USB Printer

Most new printers have a USB interface connection. You may use any one of the
ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (u npacking, p aper tr ay, toner/ink car­tridge etc.).

2. Turn ON the computer.

3. Turn ON the printer.

4. Connect the printer’s USB cable to one of the USB port s on the computer.

5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar
(you will need to purchase a parallel to USB converter).



Parallel Printer

After setting up the print­er attach the parallel ca­ble to the printer.

Connect the printer’s
parallel cable to the Par­allel to USB converter,
and then plug the con­verter into the USB port.

Turn ON the printer,
then turn ON the com­puter.

Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen in­structions.

Storage Devices, Mouse, Audio & Printer

2-22

2

Power Management

Overview 3 - 1

3

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.



OS Note

Power management
functions will vary slight­ly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operat­ing system.

(Note: All pictures used
on the following pages
are from the Windows 7
OS.)

Power Management

3 - 2 The Power Sources

3

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components (see page D - 5).

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 14).

We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 10.

Power Management

Turning On the Computer 3 - 3

3

Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.



Forced Off

If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the sys­tem to turn itself off.

Power Button as

Stand by or

Hibernate Button

You can use the OS’s
Power Options control
panel to set the power
button to send the sys­tem into Stand by or Hi­bernate mode (see your
OS’s documentation, or

“Configuring the Pow­er Buttons” on page 3

- 8 for details).



Shut Down

Note that you should always shut your computer down by choosing the Shut Down com­mand from the bottom right of the Start menu in Windows. This will help prevent hard disk
or system problems.

Power Management

3 - 4 Power Plans

3

Power Plans

The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.



Resuming
Operation

See Table 3 - 1, on

page 3 - 9 for informa-

tion on how to resume
from a power-saving
state.

Password

It is recommended that
you enable a password
on system resume in or­der to protect your data.

Figure 3 - 1

Power Plan

Advanced Settings

(Win 7)

Power Management

Power Plans3-5

3

Each Windows power plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) pow­ered.

Figure 3 - 2

Power Plans (Win 7)

Click to Show/Hide
additional
power plans

Power Management

3 - 6 Power-Saving States

3

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where
you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.

If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer do wn before the battery becomes
depleted.

Power Management

Power-Saving States 3 - 7

3

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from Shut down takes longer than
from Sleep or Hibernate.

Figure 3 - 3

Start Menu Power

Win 7

Power Management

3 - 8 Configuring the Power Buttons

3

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state. Click Choose what the power buttons do on
the left menu in Power Options to bring up the menu.



Password
Protection

It is recommended that
you enable a password
on wake up in order to
protect your data.

However you can dis­able this setting from the
Power Options menu
by clicking Require a

password on wakeup

in the left menu, and se­lecting the options (click

Change settings that
are currently unavail­able).

Figure 3 - 4

Power Options

Define Power

Buttons

Power Management

Configuring the Power Buttons 3 - 9

3

Resuming Operation

You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Icon Color

To Resume

Power Off Off Press the Power Button

Sleep Blinking Green

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Hibernate

Off (battery)

Press the Power Button

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse/Touchpad



Closing the Lid

If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.

Table 3 - 1

Resuming
Operation



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).

Power Management

3 - 10 Battery Information

3

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure

3 - 1 on page 3 - 4).

Click the battery icon in the taskbar to see the current battery level and charge
status.



Low Battery

Warning

When the battery is criti­cally low, immediately
connect the AC/DC
adapter to the computer
or save your work, oth­erwise, the unsaved
data will be lost when
the power is depleted.

Figure 3 - 5

Battery Icon

(Taskbar) & Battery

Advanced Settings

Power Management

Battery Information 3 - 11

3

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or communication applications when they are
not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.



Windows Mobility

Center

The Windows Mobility
Center control panel

provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.

Figure 3 - 6

Windows Mobility

Center

Power Management

3 - 12 Battery Information

3

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 14 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-

tors” on page 1 - 7 for information on the battery charge status, and to “Battery In­formation” on page 3 - 10 for more information on how to maintain and properly

recharge the battery pack.)

Power Management

Battery Information 3 - 13

3

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has been d roppe d we do
not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.



Caution

Danger of explosion if
battery is incorrectly re­placed.

Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s in­structions.

Power Management

3 - 14 Battery Information

3

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

Figure 3 - 7

Power Plan Create

Power Management

Battery Information 3 - 15

3

3. Click Change plan sett ings (after creating it) and click Change plan settings >

Change advanced power settings.

Figure 3 - 8

Change Plan

Settings / Change

Advanced Power

Settings

Power Management

3 - 16 Battery Information

3

4. Scroll down to Battery and click + to expand the battery options.

5. Choose the options below (click Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

Figure 3 - 9

Power Options

Advanced Settings -

Battery

Power Management

Battery Information 3 - 17

3

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.



SLI Multi GPU Configuration & Battery Power

Note that due to the high power and system demands created by enabl ing SLI Configu ra­tion, you should not enable SLI configuration if your computer is powered by battery
only. If you attempt to run an SLI config uration when the computer is powered by the bat­tery only, then system problems may occur.

If the computer is currently powered by battery only do not enable SLI configuration.
If you have currently enabled SLI configurati on, and the computer is powered by the AC/

DC adapter, do not switch to battery power only (or go to the NVIDIA Control Panel and
disable SLI configuration before switching to battery power only).

Power Management

3-18

3

Drivers & Utilities

What to Install 4 - 1

4

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utili­ties essential to the operation or improvement of some
of the computer’s subsystems. The system takes ad­vantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-config­ured with an appropriate driver or utility during oper­ating system installation. Instead, you need to
manually install some system-required drivers and
utilities.

RAID & AHCI Setup

Note that setting up a RAID, or AHCI mode, needs to
be done prior to installing the Windows OS, and there­fore before installing the other drivers listed here (see

“Setting Up SATA RAID Mode” on page 7 - 2).

What to Install

The Device Drivers & Utilities + User’s Manual disc
contains the drivers and utilities necessary for the
proper operation of the computer.

Table 4 - 1, on page 4 - 3 lists what you need to install

and it is very important that the drivers are in-
stalled in the order indicated.

Module Driver Installation

The procedures for installing drivers for the WLAN,
PC Camera, Consumer Infrared (for TV tuner re-

mote), Bluetooth & WLAN Combo and Security
(Fingerprint & TPM modules) are provided in

“Modules” on page 7 - 1.

Drivers & Utilities

4 - 2 Driver Installation

4

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.

Figure 4 - 1 - Drivers Installer Screen 1

1. Check the driver installation order from Table 4 - 1,

on page 4 - 3 (the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below .

2. Click to select the driver you wish to install, (you
should note down the drivers as you install them).

3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.

Figure 4 - 2 - Drivers Installer Screen 2

Drivers & Utilities

Driver Installation 4 - 3

4

Table 4 - 1 - Driver Installation

Note that you need to install both the WLAN & Bluetooth drivers for Intel and 3rd party WLAN & Bluetooth
Combo modules.

Windows 7 Driver Page Windows 7 Driver Page

Chipset Page 4 - 7 Intel Rapid Storage Technology (for RAID) Page 7 - 8
Video (NVIDIA)

Video (AMD)

Page 4 - 7 Wireless LAN Module Page 7 - 15

LAN Page 4 - 7 PC Camera Module Page 7 - 33
Card Reader Page 4 - 7 TV Tuner Module Page 7 - 41

TouchPad Page 4 - 8

Bluetooth Module

(note that you need to install both the WLAN &
Bluetooth drivers for the WLAN & Bluetooth
Combo module)

Page 7 - 44

USB 3.0 Page 4 - 8 Fingerprint Reader Module Page 7 - 60
Hot Key Page 4 - 8 Trusted Platform Module Page 7 - 67
Audio Page 4 - 8

Drivers & Utilities

4 - 4 Driver Installation

4

Manual Driver Installation

Click the Browse CD/DVD button in the Drivers In­staller application and browse to the executable file in

the appropriate driver folder.

Windows Update

After installing all the drivers make sure you enable
Windows Update in order to get all the latest securi ty
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -

9 for instructions.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as
outlined in this chapter.

If the driver is not listed in the Programs and Fea-
tures menu:

1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).

2. Double-click Device Manager (Hardware and
Sound > Device Manager).

3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).

4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.

Drivers & Utilities

Driver Installation 4 - 5

4

User Account Control

If a User Account Control prompt appears as part of
the driver installation procedure, click Continue/Al-
low, and follow the installation procedure as directed.

Windows Security Message

If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the in­stallation procedure.

You will receive this message in cases where the driv­er has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” dur­ing the installation procedure (other than when out-
lined in the driver install procedure), click Cancel
to close the window, and follow the installation proce­dure.

Drivers & Utilities

4 - 6 Driver Installation

4

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers
(button) to access the Optional driver menu.

RAID Note: Setting up a RAID, or AHCI mode, needs to be done prior to installing the Windows OS, and there­fore before installing the other drivers listed here.



Driver Installation General Guidelines

The driver installation procedure outlined in this
Chapter (and in Chapter 7 Options & Modules),
are accurate at the time of going to press.

Drivers are always subject to upgrade and revision
so the exact procedure for certain drivers may differ
slightly. As a general guide follow the default on
screen instructions for each driver (e.g. Next > Next
> Finish) unless you are an advanced user. In many
cases a restart is required to install the driver.

Drivers & Utilities

Driver Installation 4 - 7

4

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

The video driver installation procedure will depend
upon which video adapter is included in your purchase
option (NVIDIA or AMD).

Video (NVIDIA)

1. Click 2.Install Video Driver > Yes.

2. Click AGREE AND CONTINUE (button) to

accept the terms of the license agreement.

3. Click NEXT.

4. Click the RESTART NOW button to restart

the computer.

After the video driver has been installed, and the sys­tem restarted, the OS will automatically run the "Win­sat.exe" to rate the performance. Allow time for this
process to finish and do not restart during this process
(if you have restarted the system see “Windows Up-

date” on page 4 - 9).

Video (AMD)

1. Click 2.Install Video Driver > Yes.

2. Click Next > Install (button).

3. Click the Express (or Custom if you prefer to

manually configure the driver installation set­tings) button and click Next.

4. Click Accept (button) and click Yes.

5. Click Finish > Yes to restart the computer.

6. After the computer has restarted, click Restart

Now to restart again to refresh the video driver.

LAN

1. Click 3.Install LAN Driver > Yes.

2. Click Install.

3. Click Finish to complete the installation.

Card Reader

1. Click 4.Install Cardreader Driver > Yes.

2. Click Install > Finish.

Drivers & Utilities

4 - 8 Driver Installation

4

TouchPad

1. Click 5.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then

click Next.

4. Click Finish > Restart Now to restart the com-

puter.

USB 3.0

1. Click 6.Install USB 3.0 Driver > Yes.

2. Click Next.

3. Click the button to accept the license and then

click Next.

4. Click Next > Install.

5. Click Finish.

Hot Key

1. Click 7.Install Hotkey AP > Yes.

2. Click Next > Next.

3. Click Finish > Finish to restart your computer.

Audio

1. Click 8. Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

It is recommended that you install the Intel Rapid
Storage Technology driver (see “Intel Rapid Storage

Technology” on page 7 - 8 - required for AHCI &

RAID mode).

(see over)

Drivers & Utilities

Driver Installation 4 - 9

4

4.

Windows Experience Index

After the drivers are installed follow this procedure to
ensure an accurate rating from the Windows Experi-
ence Index (make sure the AC/DC adapter is plugged
in):

1. Click Start, and click Control Panel.

2. Click Performance Information and Tools

(System and Security > System > Check the
Windows Experience Index).

3. Click “Rate this computer/Refresh Now/Re-

run the assessment”.

4. The computer will take a few minutes to assess

the system performance.

5. Close the control panel.



Windows Update

After installing all the drivers make sure you enable Win­dows Update in order to get all the latest security up-

dates etc. (all updates will include the latest hotfixes
from Microsoft).

To enable Windows Update make sure you are con-
nected to the internet:

1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).

2. Click Windows Update (System and Security/
Security).

3. Click Check for updates (button).

4. The computer will now check for updates (you
need to be connected to the internet).

5. Click Install now (button) to begin checking for the
updates.

6. Click Install updates (button) to install the

updates.

Drivers & Utilities

4 - 10 Driver Installation

4

Optional Drivers

See the pages indicated for the driver installation pro­cedures for any modules included in your purchase op­tion.

Figure 4 - 3 - Optional Drivers Installer Screen

RAID Setup

Note: Prior to setting up the RAID you will need to use
an operable computer to copy the RAID driver to a
USB flash drive before installing the Windows operat-
ing system. See “Setting Up SATA RAID Mode” on

page 7 - 2 for configuration instructions.

Bluetooth Module

If your purchase option includes the standalone V2.1
Bluetooth module then no driver is required. If your
purchase option includes the Combination Wireless
LAN & V3.0 Bluetooth module then install the driver

as instructed in “3rd Party Bluetooth Combo Driver

Installation” on page 7 - 46 or “Intel Bluetooth Com­bo Driver Installation” on page 7 - 54.

Wireless LAN

See the appropriate install procedure for your WLAN
module in “Click Advanced and click Verify, then

click Verify (button) to begin the process.” on page 7

- 13.

Drivers & Utilities

Driver Installation 4 - 11

4

PC Camera

See the install procedure in “PC Camera Module” on

page 7 - 32.

Consumer Infrared (for TV Tuner Remote)

See the install procedure in “TV Tuner Module” on

page 7 - 40.

Security Modules (Fingerprint & TPM)

See the install procedures in “Fingerprint Reader

Module” on page 7 - 60 and “Trusted Platform Mod­ule” on page 7 - 65.

Drivers & Utilities

4-12

4

BIOS Utilities

Overview 5 - 1

5

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are makin g important changes to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your
system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.



BIOS Screens

Note that the BIOS
screens pictured on
these pages are intend­ed for guidance in set­ting up your system’s
BIOS.

BIOS versions are sub­ject to constant change
and revision, therefore
your computer’s actual
screens may appear
slightly different from
those pictured on these
pages.

BIOS Utilities

5 - 2 The Power-On Self Test (POST)

5

The Power-On Self Test (POST)

If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you
turn on the computer the system takes a few seconds to conduct a POST, including
a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.



POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt
appears only during

POST

Note:

The

POST

screen
as pictured right is for
guideline purposes only.
The

POST

screen on
your computer may ap­pear slightly different. If
the

Boot-time Diagnos-

tic Screen is disabled

(see page

5 - 9

as per the
default setting), the POST
screen will not appear.

Figure 5 - 1

POST Screen

1

2

3

4