EUROCOM Notebook V09.2.00 User Manual

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©September 2009

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experie nc ed radio/TV technician for help.

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.

If your purchase option includes both Wireless LAN and 3.5G modules, then the appropriate antennas will be installed. Note
that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or o perate in
conjunction with any other antenna or transmitter.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitche n sink or laundry tub, in a wet
basement or near a swimming pool.

2. Avoid using this eq uipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC
Output of 19V, 4.74A (90 Watts) minimum AC/DC Adapter.

CAUTION

Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELE-

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and powe r supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.

Do not expose the computer
to any shock or vibration.

Do not place it on an unstable
surface.

Do not place anything heavy
on the computer.

Do not expose it to excessive
heat or direct sunlight.

Do not leave it in a place
where foreign matter or mois­ture may affect the system.

Don’t use or store the com­puter in a humid environment.

Do not place the computer on
any surface that will block the
Vents/Fan Intakes.

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g proc edu res for the comput er. Shut the computer down properly and don ’t forge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

5. Take care when using peripheral devices.

Do not turn off the power
until you properly shut down
all programs.

Do not turn off any peripheral
devices when the computer is
on.

Do not disassemble the com­puter by yourself.

Perform routine maintenance
on your computer.

Use only approved brands of
peripherals.

Unplug the power cord befor e
attaching peripheral devices.

Preface

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a

steady , uninte rrupted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third

prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not

by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current

load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power

supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power
cord if you are wet.

Do not use the power cord if
it is broken.

Do not place heavy objects
on the power cord.



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon­nected all peripherals
and cables (including
telephone lines). It is
advisable to also re­move your battery in
order to prevent acci­dentally turning the
machine on.

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way . Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to your servi ce represent ative or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its ca rrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard ­ware and software. Make sure your documents are prepared.



Power Off Before Traveling

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher th an your hips. Place yo ur feet flat on the floor or on
a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light .

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front o f you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too lo ng).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

Preface

Preface

Contents

Notice ................................................................................. I

FCC Statement .............................................................II

FCC RF Radiation Exposure Statement: ................... III

Instructions for Care and Operation ........................... V

Power Safety .............................................................VII

Battery Precautions ................................................. VIII

Cleaning ..................................................................... IX

Servicing .................................................................... IX

Travel Considerations .................................................X

Quick Start Guide

Overview ........................................................................1-1

Advanced Users ...........................................................1-2

Beginners and Not-So-Advanced Users ......................1-2

Warning Boxes ............................................................1-2

Not Included ................................................................1-3

System Startup .............................................................1-4

System Software ..........................................................1-5

Keyboard - Model A ....................................................1-11

Keyboard - Model B .......................................... .... ......1-12

Function/Hot Key Indicators .......................................1-13

System Map: Front & Left Views ................................1-14

System Map: Right & Rear Views .............................. 1-15

System Map: Bottom View - Model A ........................1-16

System Map: Bottom View - Model B ........................1-17

Windows Vista Start Menu & Control Panel ...............1-18

Video Features .............................................................1-19

Display Devices & Options ......................... .... ..........1-20

Power Options ............................................ ..................1-21

Features & Components

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

Optical (CD/DVD) Device ............................................2-3

Loading Discs ..............................................................2-3

Handling CDs or DVDs ...............................................2-4

Preface

Gestures and Device Settings ......................................2-9

Audio Features .............................................................2-11

Adding a Printer ...........................................................2-12

USB Printer ..............................................................2-12

Parallel Printer ..........................................................2-12

Power Management

Overview ........................................................................3-1

The Power Sources .......................................... .... ..........3-2

AC/DC Adapter .......... .... .... .... .....................................3-2

Battery .........................................................................3-2

Turning on the Computer ...............................................3-3

Power Plans ...................................................................3-4

Power-Saving States ......................................................3-6

Sleep ...........................................................................3-6

Hibernate ....................................................................3-7

Shut Down ..................................................................3-7

Configuring the Power Buttons .....................................3-8

Resuming Operation ...................................................3-9

Recharging the Battery with the AC/DC Adapter .....3-13

Proper handling of the Battery Pack .........................3-14

Battery FAQ ..............................................................3-15

Drivers & Utilities

What to Install ................................................................4-1

Module Driver Installation ..........................................4-1

Driver Installation ..........................................................4-2

Updating/Reinstalling Individual Drivers ...................4-4

User Account Control (Win Vista) ..............................4-4

Windows Security Message .........................................4-4

New Hardware Found ..................................................4-5

Driver Installation Procedure .......................................4-5

Chipset ........................................................................ 4-5

Video ..........................................................................4-5

Audio ..........................................................................4-6

Modem ........................................................................ 4-6

LAN ............................................................................4 -6

TouchPad .................................................................... 4-6

Preface

Fingerprint Reader Module ........................................4-8

BIOS Utilities

Overview ........................................................................5-1

The Power-On Self Test (POST) ................................... 5-2

Failing the POST .........................................................5-3

Fatal Errors .................................................................5-3

Non-Fatal Errors .........................................................5-3

The Setup Program ........................................................5-4

Entering Setup .............................................................5-4

Setup Screens ...............................................................5-5

Main Menu .....................................................................5-6

System Time & Date (Main Menu) ...............................5-6

SATA Port 1/2/5 (Main Menu) ......................................5-7

System Memory (Main Menu) ......................................5-7

BIOS Revision/KBC/

EC Firmware Revision (Main Menu) ............................5-7

VGA Card/VBIOS Revision/

VBIOS Build Date (Main Menu) ..................................5-7

Set Supervisor Password (Security Menu) ..................5-10

Set User Password (Security Menu) ............................5-11

Fixed disk boot sector: (Security Menu) ......................5-11

Password on boot: (Security Menu) .............................5-11

Boot Menu ...................................................................5-12

Exit Menu ....................................................................5-13

Upgrading The Computer

Overview ........................................................................6-1

When Not to Upgrade ..................................................6-2

Removing the Battery ....................................................6-3

Upgrading the Hard Disk Drive .....................................6-4

Upgrading the Optical (CD/DVD) Device ....................6-7

Upgrading the System Memory (RAM) ........................6-9

Modules & Options

Overview ........................................................................7-1

Bluetooth Module ..........................................................7-2

Bluetooth Configuration in Windows Vista ...............7-3

Preface

Intel® Wi-Fi Link Series My WiFi

Driver Installation .....................................................7-13

Windows Mobility Center ................................. .... ....7-24

PC Camera Module ......................................................7-25

PC Camera Driver Installation .................................7-26

3.75G/HSPA Module ...................................................7-33

HSPA Modem Interface ............................................7-37

HSPA Modem Interface Installation ........................7-37

HSPA Modem Interface ...........................................7-38

Adding a Profile .......................................................7-40

Contacts .................................................................... 7-42

Messages ...................................................................7-43

Settings .....................................................................7-44

Mobile Partner ...........................................................7-46

Mobile Partner Application Installation ...................7-46

Mobile Partner Application ...................................... 7-47

Profile Management .................................................7-47

Fingerprint Reader Module ..........................................7-51

Fingerprint Reader Driver Installation .....................7-51

Backup and General Maintenance .................................8-3

Viruses ...........................................................................8-4

Upgrading and Adding New Hardware/Software .......... 8-5

Problems and Possible Solutions ...................................8-7

Screen Resolution Error ...............................................8-12

Interface (Ports & Jacks)

Overview ....................................................................... A-1

ATI Video Driver Controls

ATI Video Driver Installation .......................................B-1

ATI Catalyst® Control Center ......................................B-2

Attaching Other Displays ..............................................B-4

HDMI Audio Configuration .....................................B-6

Display Modes ..............................................................B-9

Clone Mode .............................................................B-10

Extended Mode .......................................................B-11

Theater Mode ..............................................................B-14

PowerPlay™ ............................................................... B-15

Preface

Video Adapter ...............................................................C-2

BIOS ............................................................................. C-2

Storage .......................................................................... C-2

Audio ............................................................................ C-2

Keyboard & Pointing Device ........................................C-2

Card Reader .................................. ................................C-2

Interface ........................................................................ C-3

Slots .............................................................................. C-3

Communication ............................................................. C-3

Communication (cont’d) ...............................................C-3

Power Management ......................................................C-3

Power ............................................................................ C-4

Security ......................................................................... C-4

Operating System .......................................................... C-4

Environmental Spec ......................................................C-4

Dimensions & Weight .................................................. C-4

Optional ........................................................................ C-4

Windows 7 Information

Model Differences ........................................................D-2

Attaching Other Displays ..............................................B-9

ATI Catalyst® Control Center ....................................B-11

Display Modes ............................................................D-15

The Power Sources .....................................................D-18

AC/DC Adapter ...........................................................D-18

Battery..........................................................................D-18

Turning On the Computer ...........................................D-19

Power Plans .................................................................D-20

Power-Saving States ...................................................D-22

Sleep ........................................................................D-22

Hibernate .................................................................D-23

Shut down ................................................................D-23

Configuring the Power Buttons ..................................D-24

Resuming Operation ................................................D-25

Energy Star Power Saving...........................................D-26

Battery Information .....................................................D-27

Battery Power ................................. .........................D-27

Conserving Battery Power ........................................D-28

Battery Life ...............................................................D-29

Preface

Driver Installation Procedure.......................................D-35

Optional Drivers .......................................................D-37

Bluetooth Module (Win 7) ..........................................D-38

Bluetooth Configuration in Windows 7 ..................D-39

Wireless LAN Module (Win 7) ..................................D-43

Connecting to a Wireless Network ...........................D-45

Intel® My WiFi Installation & Configuration .........D-48

Windows Mobility Center ................................. .... ...D-60

Fingerprint Reader Module (Win 7) ...........................D-61

Quick Start Guide

1

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), TouchPad & Mouse, Audio & Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s Bluetooth, PC Camera, Wireless LAN, 3.75G/HSPA and Secu-
rity modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

Quick Start Guide

1

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes



Notes

Check the light colored
boxes with the mark
above to find detailed in­formation about the com­puter’s features.

Quick Start Guide

1

Not Included

Operating Systems (e.g. Windows Vista/Windows 7) and applications (e.g. word processing, spreadsheet and da­tabase programs) have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If
your system hasn’t been properly configured (your service representative may have already done that for you); refer to

Chapter 4 for installation instructions.

Ports and Jacks

See Appendix A for a description of the interface (ports & jacks) which allow your computer to communicate with external
devices, connect to the internet etc.

Quick Start Guide

1

System Startup

1. Remove all packing materials.

2. Place the computer on a stable surface.

3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

5. Use one hand to raise the

lid/LCD to a comfortable viewing angle (do not exceed 120 degrees);

use the other
hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by
the lid/LCD).



Quick Start Guide

1

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the following operating systems are sup­ported (see Appendix D for Windows 7 specific information).

Table 1 - 1 - Operating Systems Supported

Operating System & Version Note

Windows Vista - SP2 (Home Basic, Home Premium, Business, Enterprise

and Ultimate Editions)

In order to run Windows Vista/Windows 7
without limitations or decreased performance,
your computer requires a minimum 1GB of
system memory (RAM).

Windows 7



Windows Vista Service Pack 2

Make sure you install Windows Vista Service Pack 2 (or a Windows Vista version which includes Service Pack 2) before installing
any drivers. Go to the Microsoft website for download details, or contact your service center.

Quick Start Guide

1

Model Differences

This notebook series includes two different model types. The models differ as indicated in the table below however
all other features, modules and specifications are identical (see Appendix D).

Feature Model A Model B

Display Type

Supported

17" WXGA(1440 * 900) /

WUXGA (1920 * 1200) TFT LCD

15.6" HD 16:9 Wide Screen (1366 * 768) /
HD+ (1600 * 900) /

FHD (1920 * 1080) TFT LCD

Design

Quick Start Guide

1

System Map: LCD Panel Open - Model A

Figure 1 - 2

LCD Panel Open

(Model A Computers)

1. Built-In PC Camera

2. LCD

3. Power Button

4. Hot Key Buttons

5. Keyboard

6. Built-In Microphone

7. Touchpad &
Buttons

8. Fingerprint Module
(Optional)

9. LED Indicators

2

4

1

6

3

5



Wireless Device

Operation Aboard Aircraft

The use of any portable electronic trans­mission devices aboard aircraft is usually
prohibited. Make sure the module(s) are
OFF if you are using the computer aboard
aircraft.

Use the key combinations to toggle power
to the 3.75G/HSPA/WLAN/Bluetooth
modules, and check the LED indicator
icon to see if the modules are powered on
or not (see Table 1 - 6, on page 1 - 13/

Table 1 - 4, on page 1 - 9).

7

Quick Start Guide

1

System Map: LCD Panel Open - Model B

Figure 1 - 3

LCD Panel Open

(Model B Computers)

1. Built-In PC Camera

2. LCD

3. Power Button

4. Hot Key Buttons

5. Keyboard

6. Built-In Microphone

7. Touchpad &
Buttons

8. LED Indicators

Note: The Fingerprint
Reader module is also an
option for Model B com­puters.

2

4

1

6

3

5



Wireless Device

Operation Aboard Aircraft

The use of any portable electronic
transmission devices aboard air­craft is usually prohibited. Make
sure the module(s) are OFF if you
are using the computer aboard air­craft.

Use the key combinations to toggle
power to the 3.75G/HSPA/WLAN/
Bluetooth modules, and check the
LED indicator icon to see if the
modules are powered on or not
(see Table 1 - 6, on page 1 - 13/

Table 1 - 4, on page 1 - 9).

Quick Start Guide

1

LED Indicators

The LED indicators on the computer display helpful
information about the current status of the computer.

Table 1 - 3 - LED Status Indicators

Table 1 - 4 - LED Power & Communication Indicators

Icon Color Description

Green Hard Disk Activity

Green Number Lock Activated

Green Caps Lock Activated

Green

Scroll Lock Activated (to activate

press Fn & Scr Lk)

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green

The Computer is in Sleep

Mode

Orange The Battery is Chargi ng

Green The Battery is Fully Charged

Blinking Orange

The Battery Has Reached

Critically Low Power Status

Green

The (optional) Wireless LAN

Module is Powered On

Orange

The (optional) Bluetooth

Module is Powered On

Quick Start Guide

1

Hot Key Buttons & Keyboard

These buttons give instant access to the default Internet browser and e-mail program,
and allow you to toggle the Silent Mode on/off with one quick button press.

Table 1 - 5 - Hot Key Buttons

*When enabled, Silent Mode will reduce fan noise and save power consumption.
Note this may reduce computer performance.

Hot Key Function

Activate the Default E-Mail Browser (Note that in Windows 7 this button

will only function after Outlook or Outlook Express are installed)

Activate the Default Internet Program

Toggle *Silent Mode (for power saving)



Other Keyboards

If your keyboard is
damaged or you just
want to make a
change, you can use
any standard USB key­board. The system will
detect and enable it
automatically. Howev­er special functions/
hot-keys unique to the
system’s regular key­board may not work.

NumLk & ScrLk

Hold down the Fn Key
and either NumLk or

Quick Start Guide

1

Keyboard - Model A

The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to
allow you to change operational features instantly. See Table 1 - 6, on page 1 - 13 for full function key combi­nation details.

Numerical Keypad

Play/Pause Key

Function Keys

NumLk &
ScrLk Keys

Toggle Key

3.75G/HSPA Module
Power

Quick Start Guide

1

Keyboard - Model B

The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to
allow you to change operational features instantly. See Table 1 - 6, on page 1 - 13 for full function key combi­nation details.

Numerical Keypad

Play/Pause Key

Function Keys

NumLk &
ScrLk Keys

Toggle Key

3.75G/HSPA Module
Power

Quick Start Guide

1

Function/Hot Key Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition
to the basic function key combinations; visual indicators are available when the hot key utility is installed.

Fn Keys Function Fn Keys Function

Fn + ~

Play/Pause

(in Audio/Video Programs)

Fn + F5/F6 Volume Decrease/Increase

Fn + _

3.75G Module
Power Toggle*

Fn + F7 Display Toggle

See “Switching Displays

Using Fn + F7” on page B - 4

Fn + F1 Touchpad Toggle Fn + F8/F9 Brightness Decrease/Increase

Fn + F2

Turn LCD Backlight Off

(Press a key to or use TouchPad to turn on)

Fn + F10

PC Camera Power

Toggle

Fn + F3 Mute Toggle Fn + F11 WLAN Module Power Toggle

Fn + F4 Sleep Toggle Fn + F12 Bluetooth Module Power Toggle

Quick Start Guide

1

System Map: Front & Left Views

Figure 1 - 6

Front & Left Views

1. LED Power & Com­munication Indica­tors

2. DC-In Jack

3. External Monitor
Port

4. RJ-45 LAN Jack

5. e-SATA Port

6. HDMI-Out Port

7. Vent/Fan Intake/
Outlet

8. 2 * USB 2.0 Ports

9. ExpressCard Slot
(see page 2 - 7)

10. 7-in-1 Card Reader

2

5

4

1

6

3



7-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /

MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /

Mini SD (requires PC adapter) / RS MMC (requires PC adapter)

\

7

8

9

10

8

Quick Start Guide

1

System Map: Right & Rear Views

Figure 1 - 7

Right & Rear Views

1. S/PDIF-Out Jack

2. Microphone-In
Jack

3. Headphone-Out
Jack

4. USB 2.0 Port

5. Optical Device
Drive Bay (for CD/
DVD Device - see
page 2 - 3)

6. RJ-11 Phone Jack

7. Security Lock Slot

8. Battery



Disk Eject Warning

152

4

8

3

6

7



CD/DVD Emergency Eject

If you need to manually eject a CD/
DVD (e.g. due to an unexpected
power interruption) you may push the
end of a straightened paper clip into
the emergency eject hole. Do not use
a sharpened pencil or any object that



Changing DVD Regional Codes

Go to the Control Panel and double-click Device
Manager (Hardware and Sound), then click the +

next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dialog
box, and select the DVD Region (tab) to bring up
the control panel to allow you to adjust the regional
code.

Quick Start Guide

1

System Map: Bottom View - Model A

Figure 1 - 8

Bottom View

(Model A

Computers)

1. Battery

2. RAM & CPU Bay
Cover

3. Vent/Fan Intake/
Outlet

4. Hard Disk Bay
Cover

5. 3.75G/HSPA
USIM Card
Location

6. Speakers

2

3

1

4

5

6

3

3

6



Battery Information

Always completely dis­charge, then fully charge, a
new battery before using it.
Completely discharge and
charge the battery at least
once every 30 days or after
about 20 partial discharges.
See “Energy Star Power

Saving” on page 3 - 10 for

full instructions.



CPU

3

Quick Start Guide

1

System Map: Bottom View - Model B

Figure 1 - 9

Bottom View

(Model B

Computers)

1. Battery

2. RAM & CPU Bay
Cover

3. Vent/Fan Intake/
Outlet

4. Hard Disk Bay
Cover

Note: the 3.75G/HSPA
USIM Card is located un­der the RAM & CPU Bay
Cover.

2

3

1

4

3

3



Battery Information

Always completely dis­charge, then fully charge, a
new battery before using it.
Completely discharge and
charge the battery at least
once every 30 days or after
about 20 partial discharges.
See “Energy Star Power

Saving” on page 3 - 10 for

full instructions.



CPU

Quick Start Guide

1

Windows Vista Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.

Figure 1 - 10 - Start Menu & Control Panel

Click here to toggle Classic View

Quick Start Guide

1

Video Features

You can configure display options, from the Display Settings control panel in Windows as long as the appro­priate video driver is installed. For more detailed video information see “ATI Video Driver Controls” on

page B - 1.

To access Display Settings in Windows:

1. Click Start, and click Control Panel (or point to Settings and click Control Panel).

2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click
Personalization > Display Settings).

3. Move the slider to the preferred setting in Resolution: (Figure 1 - 11 on page 1 - 20).

4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 11 on page 1 - 20).

5. Click Advanced Settings (button) (Figure 1 - 11 on page 1 - 20).

To access the ATI Catalyst Control Center (See Appendix B for detailed information):

1. Click Advanced Settings (button) (Figure 1 - 11 on page 1 - 20).

2. Click ATI Catalyst Control Center (tab) (Figure 1 - 11 on page 1 - 20).

3. Click ATI Catalyst Control Center (button) (Figure 1 - 11 on page 1 - 20) to access the control panel.

4. You can select Basic or Advanced options on the first run of the control panel (you can select Basic or

Advanced views from the View menu at any time).

1

2

3

3

4

5

Quick Start Guide

1

Display Devices & Options

Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as
your display device.

1

2

3

5

4



Quick Start Guide

1

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 17 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-
figuration options.

Pay attention to the instructions on battery care in “Energy Star Power Saving” on page 3 - 10.

Quick Start Guide

1

Features & Components

2

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components
of the computer:

•Hard Disk Drive

• Optical (CD/DVD) Device

• 7-in-1 Card Reader

• ExpressCard Slot

• TouchPad and Buttons/Mouse

• Audio Features

• Adding a Printer

Features & Components

2

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) hard disk drives (see “Storage”

on page C - 2) with a height of 9.5 mm.

The hard disk is accessible from the bottom of your computer as seen below. For fur­ther details see “Upgrading the Hard Disk Drive” on page 6 - 4.



Power Safety

Before attempting to ac­cess any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the ma­chine is turned off. Also
ensure that all peripher­al cables, including
phone lines, are discon­nected from the comput­er.

Model BModel A

21

21

Features & Components

2

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the module you purchased (see “Storage” on page C - 2). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 12).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt­ed, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.



Sound Volume

Adjustment

How high the sound vol­ume can be set depends
on the setting of the vol­ume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting (see

“Audio Features” on
page 2 - 11).

Figure 2 - 2

Optical Device

1

2

3

Features & Components

2

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.



CD Emergency Eject

If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharp­ened pencil or similar
object that may break
and become lodged in
the hole.

Disk Eject Warning

Don’t try to remove a

Features & Components

2

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on

page 1 - 15.

.

DVD Regional Coding

Region Geographical Location

1 USA, Canada

2

Western Europe, Japan, South

Africa, Middle East & Egypt

3

South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia,

Hong Kong

4

South & Central America, Mexico,

Australia, New Zealand

5

N Korea, Russia, Eastern Europe,

Table 2 - 1

DVD Regional Coding

Features & Components

2

7-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “CardReader” on page 4 - 6).

*Note: The PC adapters are usually supplied with these cards.



Card Reader Cover

Make sure you keep the
rubber cover provided in
the card reader when
not in use. This will help
prevent foreign objects
and/or dust getting in to
the card reader.

Figure 2 - 3

Left View

1. Card Reader

• MMC (MultiMedia Card)

• SD (Secure Digital)

• MS (Memory Stick)

• MS Pro (Memory Stick Pro)

• MS Duo (requires PC adapter*)

• Mini SD (requires PC adapter*)

• RS MMC (requires PC adapter*)

1

Features & Components

2

ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/
34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC
Cards). Make sure you install the Card Reader driver

(see

“CardReader” on page 4

- 6

).

ExpressCard/54 is used for applications which require a larger interface slot, e.g.
CompactFlash card reader. The number denotes the card width; 54mm for the Ex­press Card/54 and 34mm for the ExpressCard/34.

Inserting and Removing ExpressCards

• Align the ExpressCard with the slot and push it in until it locks into place (as

pictured in the generic figure below).

• To remove an ExpressCard, simply press the card to eject it.



ExpressCard

Slot Cover

Make sure you keep the
rubber cover provided in
the ExpressCard slot
when not in use. This
will help prevent foreign
objects and/or dust get­ting in to the Express­Card Slot.

Figure 2 - 4

Left View

1. Express Card
Slot

1

Features & Components

2

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you
can configure the functions by double-clicking the TouchPad driver icon on the
taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer
motion and sensitivity options to your preferences. You will find further information
at www.synaptics.com.



Mouse Driver

If you are using an ex­ternal mouse your op­erating system may be
able to auto-configure
your mouse during its
installation or only en­able its basic functions.
Be sure to check the
device’s user docu­mentation for details.

Figure 2 - 6

Mouse Properties

Features & Components

2

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (ac­tion) on the surface of the TouchPad to perform specific actions to manipulate doc­uments, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the left to access the user configurable settings.

Figure 2 - 7

Mouse Properties -

Device Settings

Features & Components

2

Scrolling

The two finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight con­tinuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree in crements.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.



Show Video

You can get a clearer
view of the gestures in­volved by clicking the
Show Video option for
each gesture item.

Select the gesture
(Pinch Zoom, Rotat-

ing, Three Fingers
Down and Three Fin­ger Flick) in the De­vice Settings >
Settings left tree menu
and click the Show
Video button to see

the demonstration vid­eo.

Features & Components

2

Audio Features

You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/
control panel (right-click the taskbar icon bring up an audio menu). The volume
may also be adjusted by means of the Fn + F5/F6 key combination.



Sound Volume

Adjustment

The sound volume level
is set using the volume
control within Windows
(and the volume func­tion keys on the comput­er). Click the volume
icon in the taskbar to
check the setting.

Right-click the icon
to access the menu

Features & Components

2

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.

USB Printer

Most current printers have a USB interface connection. You may use any one of the
ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (unp acking, p aper tr ay, toner/ink car­tridge etc.).

2. Turn ON the computer.

3. Tu rn ON the printer.

4. Connect the printer’s USB cable to one of the USB ports on the computer.

5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.



Parallel Printer

After setting up the print­er attach the parallel ca­ble to the printer.

Connect the printer’s
parallel cable to the Par­allel to USB converter,
and then plug the con­verter into the USB port.

Turn ON the printer,
then turn ON the com­puter.

Windows will identify the
printer and either load
one of its own drivers or

Power Management

3

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning on the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Energy Star Power Saving

• Battery Information

The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For



OS Note

Power management
functions will vary slight­ly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operat­ing system.

(Note: All pictures used
on the following pages
are from the Windows
Vista OS.)

Power Management

3

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-in jack on the left of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”



Silent Mode

Use the key to tog­gle Silent Mode to re­duce fan noise and save
power consumption.
Note this may reduce
computer performance.

Power Management

3

Turning on the Computer

Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.

When the computer is on, you can use the power button as a Sleep/Hibernate hot­key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down). Use Power Op-
tions (Hardware and Sound menu) control panel in Windows Vista to configure
this feature.



Shut Down

Note that you should al­ways shut your comput­er down by choosing the
Shut Down command
from the Lock Button

Menu in Windows Vis-
ta. This will help prevent

hard disk or system
problems.



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow­er button for 4 seconds, or longer, to force the system to turn itself off.

Power Button Sleep

Power Management

3

Power Plans

The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.



Resuming
Operation

See Table 3 - 1, on

page 3 - 9 for informa-

tion on how to resume
from a power-saving
state.

Password

It is recommended that
you enable a password
on system resume in or­der to protect your data.

Figure 3 - 1

Power Plan

Power Management

3

Each Windows power plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).

Choose High performance for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) pow­ered.



ATI PowerPlay™

PowerPlay™ in the ATI
Catalyst Control Cen­ter (in the Graphics Set-

tings Tree View pane)
allows you to set your
graphics processor set­tings for higher perfor­mance or longer battery
life.

Power Management

3

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where
you left off. Sleep is the default power-saving state in Windows Vista.

Earlier versions of Windows used Stand By and Hibernate as system power-saving
states. Windows Vista combines the features of Stand By and Hibernate into the de­fault Sleep power-saving state.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.



Power Button

The Power Button
in the Start Menu (in
Classic View use the
Shut Down button )
can be used to send the
computer into a power­saving state.

Sleep Mode &

Mobile PC Battery

A mobile PC in Sleep
uses very little battery
power.

After an extended peri­od of time the computer

Power Management

3

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.

Shut Down

You should shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from shut down takes longer than
from Sleep or Hibernate.

Power Management

3

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state.



Password
Protection

It is recommended that
you enable a password
on wake up in order to
protect your data.

However you can dis­able this setting from the
Power Options menu
by clicking Require a

password on wakeup

in the left menu, and se­lecting the options (click

Change settings that
are currently unavail­able).

Power Management

3

Resuming Operation

You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Icon Color

To Resume

Power Off Off Press the Power Button

Sleep Blinking Green

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Hibernate

Off (battery)

Press the Power Button

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse/Touchpad



Closing the Lid

If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.

Table 3 - 1

Resuming
Operation



Power Button

Power Management

3

Energy Star Power Saving

This system supports Energy Star power management features that place comput­ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period
of inactivity. If you want to enable Energy Star power saving then follow these in­structions:

1. Right-click the taskbar icon .

2. Select Power Conservation Modes.

3. Select Energy St ar to use the Ener gy Star power management and override othe r
power saving settings.

Figure 3 - 5

Energy Star Menu

Power Management

3

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).

Click the battery icon in the taskbar to see the current battery level and charge
status.



Low Battery

Warning

When the battery is criti­cally low, immediately
connect the AC/DC
adapter to the computer
or save your work, oth­erwise, the unsaved
data will be lost when
the power is depleted.

Figure 3 - 6

Power Management

3

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD

brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or co mmunication applications when they are

not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices,

ExpressCards etc.



Windows Mobility

Center

The Windows Mobility
Center control panel

provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.

Figure 3 - 7

Windows Mobility

Center

Power Management

3

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 15 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-

Power Management

3

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances

• DO NOT expose the battery to fire or high temperatures, it may explode

• DO NOT connect the metal terminals (+, -) to each other



Caution

Danger of explosion if
battery is incorrectly re­placed.

Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s in­structions.



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has been d roppe d we do
not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.

Power Management

3

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

3. Click Change plan settings (after saving it) and click Change advanced power
settings.

Figure 3 - 8

Power Plan Create

Power Management

3

4. Scroll down to Battery and click + to expand the battery options.

5. Choose the options below (click Yes if a warning appears):

Figure 3 - 9

Power Options

Advanced Settings -

Battery

Power Management

3

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.

Power Management

3

Drivers & Utilities

4

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utili­ties essential to the operation or improvement of some
of the computer’s subsystems. The system takes ad­vantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-config­ured with an appropriate driver or utility during oper­ating system installation. Instead, you need to
manually install some system-required drivers and
utilities.

What to Install

The Device Drivers & Utilities + User’s Manual disc
contains the drivers and utilities necessary for the
proper operation of the computer.

Table 4 - 1, on page 4 - 3 lists what you need to install

and it is very important that the drivers are in-
stalled in the order indicated (see “Windows 7 In-

formation” on page D - 1 for Windows 7

information).

Module Driver Installation

The procedures for installing drivers for the Wireless
LAN, PC Camera, 3.75G/HSPA and Fingerprint

modules are provided in “Modules & Options” on

Drivers & Utilities

4

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers/Option Drivers (button).

If you wish to install the drivers manually see overleaf
for the driver path information

.

1. Check the driver installation order from Table 4 - 1,

on page 4 - 3 (the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below.

2. Click to select the driver you wish to install, after
installing each driver it will become grayed out. If
you need to reinstall any driver, click the Unlock
button (you should uninstall the driver first).

3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.

Drivers & Utilities

4

Manual Driver Installation

Click Browse CD (button) in the Drivers Installer ap-
plication and browse to the executable file in the ap­propriate driver folder.

Windows Update

After installing all the drivers make sure you enable
Windows Update in order to get all the latest security
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -

7 for instructions.

Driver - Windows Vista with Service Pack 2

Page

Chipset Page 4 - 5
Video Page 4 - 5
Audio Page 4 - 6
Modem Page 4 - 6
LAN Page 4 - 6
TouchPad Page 4 - 6
CardReader Page 4 - 6
Hot Key Page 4 - 6

Wireless LAN Module Page 7 - 8
PC Camera Module Page 7 - 26

3.75G/HSPA Module Page 7 - 33
Fingerprint Reader Module Page 7 - 51



Windows Vista Service Pack 2

Make sure you install Windows Vista Service Pack 2
(or a Windows Vista version which includes Service
Pack 2) before installing any drivers. Go to the Micro­soft website for download details, or contact your service

Drivers & Utilities

4

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as
outlined in this chapter.

If the driver is not listed in the Programs and Fea-
tures menu:

1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).

2. Double-click Device Manager (Hardware and
Sound > Device Manager).

User Account Control (Win Vista)

If a User Account Control prompt appears as part of
the driver installation procedure, click Continue or
Allow, and follow the installation procedure as direct­ed.

Windows Security Message

If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or “Install” to continue the
installation procedure.

You will receive this message in cases where the driv­er has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.

Drivers & Utilities

4

New Hardware Found

If you see the message “New Hardware Found” dur-
ing the installation procedure (other than when out-
lined in the driver install procedure), click Cancel
to close the window, and follow the installation proce­dure.

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button).

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

Video

1. Click 2.Install Video Driver > Yes.

2. Click Next > Install (button).

3. Click the Express (or Custom if you prefer to

manually configure the driver installation set­tings) button and click Next.

4. Click Accept (button) and click Yes.

5. Click Finish > Yes to restart the computer.



Driver Installation General Guidelines

The driver installation procedure outlined in this
Chapter (and in Chapter 7 Options & Modules),
are accurate at the time of going to press.

Drivers are always subject to upgrade and revision
so the exact procedure for certain drivers may differ
slightly. As a general guide follow the default on
screen instructions for each driver (e.g. Next > Next
> Finish) unless you are an advanced user. In many

Drivers & Utilities

4

Audio

1. Click 3.Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

Modem

1. Click 4.Install Modem Driver > Yes.

2. Click OK.

3. The modem is ready for dial-up configuration.

TouchPad

1. Click 6.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then

click Next.

4. Click Finish > Restart Now to restart the com-

puter.

CardReader

1. Click 7.Install CardReader Driver > Yes.

2. Click Install.

3. Click Finish.

Hot Key

1. Click 8.Install Hotkey Driver > Yes.

2. Click Next > Install.



Modem Country Selection

Go to the Phone and Modem Options con trol panel (Hard­ware and Sound) and make sure the modem country selection

is appropriate for you.

Drivers & Utilities

4

Optional Drivers

See the pages indicated for the driver installation pro­cedures for any modules included in your purchase op­tion.



Windows Update

After installing all the drivers make sure you enable Win­dows Update in order to get all the latest security up-

dates etc. (all updates will include the latest hotfixes
from Microsoft).

To enable Windows Update make sure you are con-
nected to the internet:

1. Click Start, and click Control Panel (or point
to Settings and click Control Panel).

2. Click Check for updates (Security), or
double-click Security Center and click
Windows Update.

3. Double-click Check for updates (button).

4. The computer will now check for updates
(you need to be connected to the internet).

Drivers & Utilities

4

Bluetooth Module

Note: The operating system is the default setting for
Bluetooth control in Windows Vista, and does not re-

quire a driver. See “Bluetooth Module” on page 7 - 2
for configuration instructions.

Wireless LAN Module

See the introduction in “Wireless LAN Module” on

page 7 - 7, and check the installation procedure.

PC Camera Module

See the introduction in “PC Camera Module” on

page 7 - 25, and check the installation procedure.

3.75G/HSPA Module

See the introduction in “3.75G/HSPA Module” on

page 7 - 33, and check the installation procedure.

Fingerprint Reader Module

See the introduction in “Fingerprint Reader Module”

on page 7 - 51, and check the installation procedure.

BIOS Utilities

5

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your
system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service



BIOS Settings

Warning

Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-

up and restore the Set­up Defaults with <F9>.

BIOS Utilities

5

The Power-On Self Test (POST)

Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.



POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt
appears only during

POST

Note:

The

POST

screen
as pictured right is for
guideline purposes only.
The

POST

screen on
your computer may ap­pear slightly different. If
you disable the

Boot-

time Diagnostic Screen

,
the POST screen will not
appear.

1

2

3

BIOS Utilities

5

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “non­fatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:

• Press <F1> to resume

• <F2> to enter Setup

Press F1 to see if the boot process can continue. It may work, without the correct

BIOS Utilities

5

The Setup Program

The Phoenix Setup program tells the system how to configure itself and manage ba-
sic features and subsystems (e.g. port configuration).

Entering Setup

To enter Setup, turn on the computer and press F2 during the POST. The prompt
(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds
after you turn on the system. If you get a “Keyboard Error”, (usually because you
pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.

BIOS Utilities

5

Setup Screens

The following pages contain additional advice on portions of the Setup.

Along the top of the screen is a menu bar with menu headings. When you select a
heading, a new screen appears. Scroll through the features listed on each screen to
make changes to Setup.

Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that sub­ject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.



Setup Menus

The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configura­tion appropriate for your
model and options.

BIOS Utilities

5

Main Menu

System Time & Date (Main Menu)

Figure 5 - 2

Main Menu

BIOS Utilities

5

SATA Port 1/2/5 (Main Menu)

Pressing Enter opens the sub-menu to show the configuration of an HDD/optical de-
vice on the computer’s SATA Port 1/2/5. Use the Auto (Type:) setting to have the
items configured automatically for you.

System Memory (Main Menu)

This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.

BIOS Revision/KBC/EC Firmware Revision (Main Menu)

This item contains information on the current BIOS and firmware versions.

VGA Card/VBIOS Revision/VBIOS Build Date (Main Menu)

This item contains information on the current videos card installed, and on the Video
BIOS version.

BIOS Utilities

5

Advanced Menu

Legacy USB Support (Advanced Menu)

Figure 5 - 3

Advanced Menu

BIOS Utilities

5

Boot-time Diagnostic Screen (Advanced Menu)

Use this menu item to enable/disable the Boot-time Diagnostic Screen or Power-On
Self Test (see “The Power-On Self Test (POST)” on page 5 - 2).

Legacy OS Boot: (Advanced Menu)

Enable this item to support only system boot from the Legacy OS (e.g Windows Vis­ta). If disabled the system will attempt to boot from the EFI (Extensible Firmware

Interface) before the Legacy OS.

Battery Low Alarm Beep (Advanced Menu)

Use this menu item to enable/disable the audible warning when the battery has
reached low power status.

BIOS Utilities

5

Security Menu

Set Supervisor Password (Security Menu)

You can set a password for access to the PhoenixBIOS Setup Utility. This will not



Security Menu

The changes you
make here affect the
access to the Setup
utility itself, and also
access to your ma­chine as it boots up af­ter you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.

Figure 5 - 4

Security Menu

BIOS Utilities

5

Set User Password (Security Menu)

You can set a password for user mode access to the PhoenixBIOS Setup Utility.
This will not affect access to the computer OS, (only the Setup utility) unless you
choose to set a Password on Boot (see below). Many menu items in the Phoenix-
BIOS Setup Utility cannot be modified in user mode. You can only set the user
password after you have set the supervisor password.

Fixed disk boot sector: (Security Menu)

If you choose “Write-Protect” this will protect against viruses being written to the
hard disk boot sector (this is not a substitute for installing an anti-virus program - see

“Viruses” on page 8 - 4).

Password on boot: (Security Menu)

Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled”
is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.



Password Warning

If you set a boot pass­word (Password on boot
is “Enabled“), NEVER
forget your password.

The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your ven­dor and you may lose all
of the information on
your hard disk.

BIOS Utilities

5

Boot Menu

When you turn the computer on it will look for an operating system (e.g. Windows

Figure 5 - 5

Boot Menu

BIOS Utilities

5

Exit Menu

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any

Figure 5 - 6

Exit Menu

BIOS Utilities

5

Upgrading The Computer

6

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the steps out­lined to make the desired upgrades. If you have any trouble or problems you can con­tact your service representative for further help. Before you begin you will need:

• A small crosshead or Phillips screwdriver

• A small regular slotted (flathead) screwdriver

• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic

wrist strap to ground yourself because static electricity may damage the compo­nents.

The chapter includes:

• Removing the Battery



Warranty Warning

Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.

Upgrading The Computer

6

When Not to Upgrade

These procedures involve opening the system’s case, adding and sometimes replac­ing parts.

You should not perform any of these upgrades if:

• Your system is still under warranty or a service contract

• You don’t have all the necessary equipment

• You’re not in the correct environment

• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or re-

place the component(s).



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and disconnect­ed all peripherals and
cables (including tele­phone lines). It is advis­able to also remove your
battery in order to pre­vent accidentally turning
the machine on.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.

Upgrading The Computer

6

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons
it is best to remove the battery.

1. Turn the computer off, and turn it over.

2. Slide the latch in the direction of the arrow.

3. Slide the latch in the direction of the arrow, and hold it in place.

4. Slide the battery out in the direction of the arrow .



Warranty Warning

Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.

Figure 6 - 1

Battery Removal

1
2

3

1

2

Upgrading The Computer

6

Upgrading the Hard Disk Drive

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard
disk drives with a height of 9.5mm (h) (see “Storage” on page C - 2). Follow your
operating system’s installation instructions, and install all necessary drivers and util­ities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk.

1. Turn off the computer, and turn it over and remove the batt er y.

2. Locate the hard disk bay cover and loosen screws & .

3. Remove the hard disk bay cover .



HDD System

Warning

New HDD’s are blank. Be­fore you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
You have all the CD-ROMs
and FDDs required to in­stall your operating system
and programs.
If you have access to the in­ternet, download the latest
application and hardware
driver updates for the oper­ating system you plan to in­stall. Copy these to a
removable medium.

1

2

3

Model BModel A

21

21