This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Page 4
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Re orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1.This device may not cause interference.
And
2.This device must accept any interference, including interference that may cause undesired operation of the
device.
II
Page 5
Preface
FCC RF Radiation Exposure Statement:
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
III
Page 6
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1.Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet
basement or near a swimming pool.
2.Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3.Do not use the telephone to report a gas leak in the vicinity of the leak.
4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5.This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -
240V, 50 - 60Hz/ DC Output 19V, 11.6A or 19V, 12.2A (220W) minimum).
This Computer’s Optical Device is a Laser Class 1 Product
IV
Page 7
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2.Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place where
foreign matter or moisture may
affect the system.
Don’t use or store the computer
in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
V
Page 8
Preface
3.Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4.Follow the proper workin g procedu res for t he comput er. Shut the computer down properly and don’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until
you properly shut down all programs.
Do not turn off any peripheral
devices when the computer is
on.
5.Take care when using peripheral devices.
Use only approved brands of
peripherals.
VI
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Page 9
Power Safety
The computer has specific power requirements:
Preface
•Only use a power adapter approved for use with this computer.
•Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninterru pted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.
•The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
•When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
•Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
•Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VII
Page 10
Preface
Battery Precautions
•Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
•Do not remove any batteries from the computer while it is powered on.
•Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
•Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qual-
ified service personnel.
•Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
•Keep the battery away from metal appliances.
•Affix tape to the battery contacts before disposing of the battery.
•Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VIII
Page 11
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.
IX
Page 12
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.Check that the battery pack and any spares are fully charged.
2.Power off the computer and peripherals.
3.Close the display panel and make sure it’s latched.
4.Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6.Put the notebook in its carrying bag and secure it with the bag’s straps.
7.If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8.Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard -
ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
X
Page 13
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XI
Page 14
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a
footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your kne es, hips an d elbows form approximately 90-degree angles when
you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• T ake periodic breaks when you work at the computer for long periods of time. Frequent and
short breaks are better than fewer and longer breaks.
XII
Page 15
Preface
Lighting
Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.
•Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
•Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
•Position the display directly in front of you at a comfortable viewing distance.
•Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
•Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.
•Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
•Rotate desktop background images every few days.
•Turn the monitor off when the system is not in use.
XIII
Page 16
Preface
XIV
Page 17
Contents
Notice ................................................................................. I
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), Game Keys, TouchPad & Mouse,
Audio Features & Printer.
• Chapter 3 The computer’s power management options.
• Chapter 4The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s RAID, Bluetooth, Wireless LAN, PC Camera, TV Tuner and Fingerprint modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the NVIDIA Video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
Page 24
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”
on page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Page 25
Quick Start Guide
Not Included
Operating Systems (e.g. Windows Vista etc.) and applications (e.g. word processing, spreadsheet and database
programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers
& Utilities” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1
Overview 1 - 3
Page 26
1
Quick Start Guide
System Software
TV Tuner Module
Support
Note that the TV Tuner
module (factory) option
in Windows Vista is
supported by the Win-
dows Media Center
software which comes
built-in to the Windows
Vista Home Premium
and Ultimate Editions
only.
If your purchase includes a TV Tuner option, and you are reconfiguring your system
for a different system,
you should install either
Windows Home Premium or Ultimate Edi-
tions only.
Your computer may already come with system software pre-installed. Where this is
not the case, or where you are re-configuring your computer for a different system,
you will find the Windows Vista (with Service Pack 1) operating system is support-
ed.
Note: In order to run Windows Vista without limitations or decreased performance,
your computer requires a minimum 1GB of system memory (RAM).
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1 (or a Windows Vista version which
includes Service Pack 1) before installing an y drivers. Go to the Microsoft website for
download details, or contact your service center.
RAID & AHCI Setup
Note that setting up a RAID, or AHCI mode, needs to be done prior to installing the
Windows OS (see“Setting Up SATA RAID or AHCI Modes” on page 7 - 2).
1 - 4 Overview
Page 27
Quick Start Guide
System Startup
1. Remove all packing materials, and place th e com p ut er on a stable surfac e.
2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3. Attach the AC/DC adapter to the DC-In jack at the rear of the compute r, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
4. Use one hand to raise the
the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the
computer by the lid/LCD).
5. Raise the lid/LCD to a comfortable viewing angle, and press the power button.
Note that you should always shut your computer down by choosing the Shut Down command from the Lock ButtonMenu in Windows Vista. This will help prevent hard disk or system problems.
lid/LCD to a comfortable viewing angle (it is preferable not to exceed 130 degrees);
Shutdown
1
use
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD
System Startup 1 - 5
Page 28
1
Quick Start Guide
Figure 1 - 2
LCD Panel Open & Top
View
1. Optional Built-In PC
Camera
2. LCD
3. LED Status Indicators
4. Touch Sensor
Instant Keys
5. 8 * Gaming Keys
6. Keyboard
7. TouchPad and
Buttons
8. Fingerprint Reader
Module (optional)
9. LED Power Indicators
10.LCD Panel Color
LED
See Appendix A for a more
detailed description of the
ports & jacks etc.
System Map: LCD Panel Open & Top View
1
Operation Aboard Aircraft
2
3
5
4
6
The use of any portable electronic
transmission devices (e.g. WLAN
or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF if you are
using the computer aboard aircraft.
Use the appropriate function key
combination/Touch Sensor Key to
toggle power to any wireless modules, and check the indicators to
see if any modules are powered on
or not (see Table 1 - 2, on page 1
- 8).
7
8
9
Wireless Device
10
1 - 6 System Map: LCD Panel Open & Top View
Page 29
Quick Start Guide
1
LED Indicators
The two sets of LED indicators (LED Status Indicators and LED Power Indicators) display helpful in-
formation about the current status of the computer.
IconColorDescription
Blinking BlueHard Disk Activity
BlueNumber Lock is Activated
BlueCaps Lock is Activated
BlueScroll Lock is Activated
GreenThe Computer is On
Blinking
Green
OrangeThe Battery is Charging
Blinking
Orange
GreenThe Battery is Fully Charged
The Computer is In Sleep Mode
The Battery has Reached
Critically Low Power Status
Game Keys
The eight Game Keys on the left of the computer allow macros to be configured for common keystrokes
used in applications, as long as the driver is installed.
Figure 1 - 3 - Game Key Configuration
Table 1 - 1 - LED Status Indicators
System Map: LCD Panel Open & Top View 1 - 7
Page 30
1
Quick Start Guide
Touch Sensor Instant Keys
Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module
is powered on the appropriate icon will be highlighted.
IconDescriptionIconDescription
LED Color Toggle (press to toggle
flashing colors or single color)
PC Camera Module Power Toggle Activate the Default Internet Browser
Bluetooth Module Power Toggle
Toggle *Silent Mode (for power saving)
Visual Indicator
Volume Control Slider (move your finger slowly along the slider to
adjust the system volume)
Table 1 - 2 - Touch Sensor Instant Keys
Wireless LAN Module Power Toggle
Sound Effects Equalizer Mode Toggle
(see page 2 - 14)
Mute Toggle
*When enabled, Silent Mode will reduce fan noise and save power consumption. Note this may reduce computer performance.
1 - 8 Touch Sensor Instant Keys
Page 31
Quick Start Guide
1
Keyboard
The keyboard has an embedded numerical keypad for easy numeric data input, and
features function keys to allow you to change operational features instantly. See
Table 1 - 3, on page 1 - 10 for full function key combination details.
Function Keys
NumLk &
ScrLk Keys
Play/Pause Key
Numerical
Keypad
Fn Key
Figure 1 - 4 - Keyboard
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
Num Lk & Scr Lk
Hold down the Fn Key
and Scr Lk/Num Lk to enable scroll lock/number
lock, and check the LED
indicator for status.
Keyboard 1 - 9
Page 32
1
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the
basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed (see “Hot Key” on page 4 - 7).
After installing the driver an icon will appear in the taskbar.
Fn + ~Play/Pause (in Audio/Video Programs)Fn +F8/F9
Fn + F1Touchpad ToggleFn + F10
Fn + F2
Fn + F3Mute ToggleFn + F12
Fn + F4Sleep ToggleFn + NumLkNumber Lock Toggle
Fn +F5/F6
Fn + F7Display Toggle
(Press a key to or use Touchpad to turn on)
Volume Decrease/
Turn LCD Backlight Off
Increase
Fn + F11
Fn + ScrLkScroll Lock Toggle
Note: DO NOT use the Fn + F7 key combination to toggle
through display options when SLI is enabled (see “SLI Multi
GPU Configuration” on page B - 13).
Brightness
Decrease/Increase
PC Camera Power
Toggle
WLAN Module
Power Toggle
Bluetooth Module
Power Toggle
Table 1 - 3 - Function Keys & Visual Indicators
1 - 10 Keyboard
Page 33
Quick Start Guide
1
System Map: Front & Rear Views
11
11
Note that the TV Tuner module options in Windows Vista is supported by the Windows
Media Center software which comes built-in to the Windows Vista Home Premium and
Ultimate Editions only.
If your purchase includes a TV Tuner option, and you are re-configuring your system for a
different system, you should install either Windows Home Premium or UltimateEditions
only.
23
2
TV Tuner Module Support
4
2
5
2
Figure 1 - 5
Front View
1. Color LEDs
2.
Speakers
3. LED Power
Indicators
4. Consumer Infrared
Transceiver
(enabled with
optional TV Tuner
only)
5. DC-In Jack
See Appendix A for a more
detailed description of the
ports & jacks etc.
System Map: Front & Rear Views 1 - 11
Page 34
1
Quick Start Guide
Figure 1 - 6
Right View
1. Headphone-In Jack
2. Microphone-In Jack
3. Line-In Jack
4. S/PDIF-Out Jack
5. Cable (CATV)
Antenna Jack
6. Combined eSATA/
USB Port
7. USB 2.0 Port
8. Security Lock Slot
9. Power Button
*Enabled with Optional
Mini-PCI TV Tuner Only
See Appendix A for a more
detailed description of the
ports & jacks etc.
*
System Map: Right View
6
4
3
2
1
TV Tuner Module Support
Note that the TV Tuner module options in Windows Vista is supported by the Windows
Media Center software which comes built-in to the Windows Vista Home Premium and
Ultimate Editions only.
If your purchase includes a TV Tuner option, and you are re-configuring your system for a
different system, you should install either Windows Home Premium or UltimateEditions
only.
USB Ports
Note that the connections to the USB ports only fit one way, do not force them.
5
7
9
8
1 - 12 System Map: Right View
Page 35
Quick Start Guide
1
System Map: Left View
1
3
2
4
5
8
Mini-IEEE 1394 Port
The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. Make sure
you install the IEEE 1394 filter driver (see page 4 - 7).
7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter)
Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
HDMI-Out Port
Note that the HDMI-Out Port supports video and audio signals to attached external displays
(also see “HDMI Audio Configuration” on page B - 8).
6
7
Figure 1 - 7
Left View
1. DVI-Out Port
2. 2 * USB 2.0 Ports
3. RJ-45 LAN Jack
4. HDMI-Out Port
5. 7-in-1 Card Reader
6. ExpressCard Slot
7. Mini-IEEE 1394 Port
8. Optional Device
Drive Bay
See Appendix A for a more
detailed description of the
ports & jacks etc.
USB Ports
Note that the connections to the USB ports
only fit one way, do not
force them.
System Map: Left View 1 - 13
Page 36
1
Quick Start Guide
Disk Eject Warning
Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop
the disk first then eject it, or press the stop button
twice.
CD/DVD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to
an unexpected power interruption) you may push the
end of a straightened paper clip into the emergency
eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole.
Don’t try to remove a floppy disk/CD/DVD while the
system is accessing it. This may cause the system to
“crash”.
Changing DVD Regional Codes
Go to the Control Panel and double-click Device
Manager (Hardware and Sound), then click th e +
next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dialog
box, and select the DVD Region (tab) to bring up the
control panel to allow you to adjust the regional code.
DVD region detection is device dependent, not OSdependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.
1 - 14 System Map: Left View
Page 37
Quick Start Guide
1
System Map: Bottom View
1
2
3
45
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 10 for full instructions.
22
Figure 1 - 8
Bottom View
1. Sub Woofer
2. Fan Outlet/Intake
3. Component Bay
Cover
4. Battery
(Secondary HDD
Bay - HDD3)
5. Primary HDD Bay
(HDD1 & 2)
See Appendix A for a more
detailed description of the
ports & jacks etc.
Overheating
To prevent your computer from overheating make
sure nothing blocks the
vent(s)/fan intake(s)
while the computer is in
use.
System Map: Bottom View 1 - 15
Page 38
1
Quick Start Guide
Windows Vista Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.
Click here to toggle Category View
Figure 1 - 9 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessedfrom the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed
in Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle off Category View.
1 - 16 Windows Vista Start Menu & Control Panel
Page 39
Quick Start Guide
Video Features
You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “NVIDIA Video Driver Controls” on
page B - 1.To access Display Settings in Windows:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click
Personalization > Display Settings).
3. Move the slider to the preferred setting in Resolution: (Figure 1 - 10 on page 1 - 18).
4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 10 on page 1 - 18).
7. Click Start theNVIDIA Control Panel (Figure 1 - 10 on page 1 - 18) to access the control panel.
8. The NVIDIA Control Panel can also be accessed by right-clicking the desktop, and then clicking NVIDIA
Control Panel (or from the NVIDIA Control Panel in the Windows control panel).
Note that card types, specifications and drivers are subject to continual updates and changes. This computer features an
NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combin ing dual NVIDIA GPUs
in a single system for some of the video card options. SLI Configuration needs to be enabled from the NVIDIA ControlPanel (3D Settings > Set SLI Configuration); see “SLI Multi GPU Configuration” on page B - 13. Check with your
service center for the latest details on video cards supported (see “Video Adapter” on page C - 2 for details). SLI Con-
figuration should not be enabled under battery power (see page B - 14).
3
4
Video Card Options
1
2
1
Video Features 1 - 17
Page 40
1
Quick Start Guide
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or
TV (connected to the DVI-Out port/HDMI-Out port) as your display device.
SingleOne display device is used.
CloneBoth connected displays output the same view
DualviewBoth connected displays are treated as separate devices, and act as a virtual desktop
Table 1 - 4 - Display Modes Available
1 - 18 Video Features
Note that SLI
configuration
supports only
Single display.
Page 41
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-
figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 10.
1
Note: Sleep is the default power saving state in Windows Vista
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
•Optical Device
•7-in-1 Card Reader
•ExpressCard Slot
•Game Keys
•Audio Features
•Adding a Printer
2
Overview 2 - 1
Page 44
Storage Devices, Mouse, Audio & Printer
2
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Power Safety
Hard Disk Drive
The hard disk drive(s) is(are) used to store your data in the computer. The hard
disk(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives
with a height of 9.5 mm. The primary hard disk bay is accessible from the bottom
of your computer as seen below, and the secondary hard disk bay is located under
the battery compartment.
The computer can accommodate up to three hard disks (two in the primary bay, and
one in the secondary bay), and these may be configured in RAID or AHCI modes.
Further details on removing and inserting the hard disk are available in “Upgrading
the Hard Disk Drive” on page 6 - 4.
1
2
2
Figure 2 - 1
Hard Disk Location
2
1
2 - 2 Hard Disk Drive
Page 45
Storage Devices, Mouse, Audio & Printer
Optical Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page C - 3). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see“Boot Menu” on page 5 - 12).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
1
2
1
2
3
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-dows. Click the Volume
icon on the taskbar to
check the setting.
Peripherals must be
connected before you
turn on the system.
Figure 2 - 2
Optical Device
2
Optical Device 2 - 3
Page 46
Storage Devices, Mouse, Audio & Printer
2
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
•Hold the CD or DVD by the edges; do not touch the surface of the disc.
•Use a clean, soft, dry cloth to remove dust or fingerprints.
•Do not write on the surface with a pen.
•Do not attach paper or other materials to the surface of the disc.
•Do not store or place the CD or DVD in high-temperature areas.
•Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
•Do not bend the CD or DVD.
•Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical Device
Page 47
Storage Devices, Mouse, Audio & Printer
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 14.
DVD Regional Coding
RegionGeographical Location
1USA, Canada
2
3
4
5
6China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia, New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Optical Device 2 - 5
Page 48
Storage Devices, Mouse, Audio & Printer
2
Card Reader Cover
Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust getting in to the card reader.
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader/ExpressCard” on page 4 - 6).
•MMC (MultiMedia Card)
•SD (Secure Digital)
•MS (Memory Stick)
•MS (Memory Stick Pro)
•MS Duo (requires PC adapter*)
•Mini SD (requires PC adapter*)
•RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 3
Right View
1.Card Reader
1
2 - 6 7-in-1 Card Reader
Page 49
Storage Devices, Mouse, Audio & Printer
ExpressCard Slot
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/
34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC
Cards).
ExpressCard/54 is used for applications which require a larger interface slot, e.g.
CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the ExpressCard driver (see “Card Reader/ExpressCard” on page 4 - 6).
1
Inserting and Removing ExpressCards
•Align the ExpressCard with the slot and push it in until it locks into place (as
pictured in the generic figure below).
•To remove an ExpressCard, simply press the card to eject it.
ExpressCard
Slot Cover
Make sure you keep the
cover in the ExpressCard slot when not in
use. This will help prevent foreign objects and/
or dust getting in to the
ExpressCard Slot.
Figure 2 - 4
ExpressCard Slot
1.Express Card
Slot
2
ExpressCard Slot 2 - 7
Page 50
Storage Devices, Mouse, Audio & Printer
2
Game Keys
The eight game hot keys on the left of the computer allow macros to be configured
for common keystrokes used in applications (the keys can assigned macros for any
program, not only games). To configure the keys follow the instructions below
(make sure you have installed the GameKey Utility driver - see “GameKey Utility”
on page 4 - 6).
1.Run the Game Key Configuration program from the desktop icon (or from
C:\Program Files (x86)\Chicony\GameKey\GmKeyCfgUtl.exe).
2.Double-click the button for the appropriate key (it will turn red ).
3.When the button is red you may then record the keystrokes to be assigned to
the Game Key.
Figure 2 - 5
Game Key
Configuration
4.Click OK.
5.Repeat the procedure for the other Game Key if required.
6.Close the Game Key Configuration window.
7.The keystroke order will be repeated with the appropriate button press in any
application program.
2 - 8 Game Keys
Page 51
Storage Devices, Mouse, Audio & Printer
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.
Install the TouchPad driver (see page 4 - 6) and then double-click the TouchPad
driver icon in the taskbar to configure the functions. You may then configure the
TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your
preferences. The TouchPad may be toggled on/off by means of the Fn + F1 key
combination.
Mouse Driver
If you are using an external mouse your operating system may be able
to auto-configure your
mouse during its installation or only enable its
basic functions. Be sure
to check the device’s
user documentation for
details.
Figure 2 - 6
Mouse Properties
2
TouchPad and Buttons/Mouse 2 - 9
Page 52
Storage Devices, Mouse, Audio & Printer
2
Audio Features
You can configure the audio options on your computer from the Sound control
Sound Volume
Adjustment
The sound volume level
is set using the volume
control within Windows
(and the volume function keys on the computer). Click the volume
icon in the taskbar to
check the setting.
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/
control panel (right-click the taskbar icon to bring up an audio menu). The volume
may also be adjusted by means of the Fn + F5/F6 key combination or by moving
your finger slowly along the Touch Sensor volume control slider (see Table 1 - 2,
on page 1 - 8).
Right-click the icon
to access the menu
above.
Figure 2 - 7
Realtek Audio
Manager
See “HDMI Audio Configuration” on page B - 8 for a description of the audio configuration
when connecting an HDMI supported display device.
2 - 10 Audio Features
Page 53
Storage Devices, Mouse, Audio & Printer
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1.Click
2.Click Realtek HD Audio Manager (or right-click the taskbar icon and select
3.Click Microphone Effects (tab) in Microphone (tab), and then click to select
4.Click OK to close the control panel and save the settings.
Start
, and click
and make sure you are in
Sound Manager).
Noise Suppression (button), or adjust the Recording Volume level to around 60,
to obtain the optimum recording quality.
Control Panel
Classic View
(or point to
.
Settings
and click
Control Panel
Beam Forming
)
If your stereo microphone supports Beam
Forming (Directional
Recording), then click
the button to calibrate
the stereo microphone
before recording.
Figure 2 - 8
Realtek Audio
Manager -
Recording Setup
2
Audio Features 2 - 11
Page 54
Storage Devices, Mouse, Audio & Printer
2
Figure 2 - 9
Speaker
Configuration
To setup your system for 5.1 surround sound you will need to connect the audio cables to the Line-In and Microphone-In jacks.
1.Click
2.Click Realtek HD Audio Manager (or right-click the taskbar icon and select
3.Click Speakers (tab) and click Speaker Configuration (tab).
4.Select 5.1 Speaker from the Speaker Configuration pull-down menu.
Start
, and click
and make sure you are in
Sound Manager).
Control Panel
Connector Settings
(or point to
Classic View
Settings
.
and click
Control Panel
Auto Popup Dialog
You should enable the
auto popup dialog to automatically detect when a
device has been
plugged-in. If disabled,
double-click connectorsettings and click the
box to enable the auto
popup detection of
plugged-n devices.
)
Setup for 5.1 Surround Sound
2 - 12 Audio Features
Page 55
Storage Devices, Mouse, Audio & Printer
5.Plug the front speaker cables into the Headphone-Out Jack.
6.Plug in the other cables (y ou may require an adapter to connect each cable to the
appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as
follows:
•Line-In Jack = Rear Speaker Out
•Microphone-In Jack = Center/Subwoofer Speaker Out
7.As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on
page 2 - 12).
8.Click to put a tick in the appropriate box according to the speaker plugged-in (e.g.
Rear Speaker Ou t), and then click OK to save the setting.
9.Click OK to exit Realtek HD Audio Manager.
2
Figure 2 - 10
Connected Device
Auto Popup
Audio Features 2 - 13
Page 56
Storage Devices, Mouse, Audio & Printer
2
Press the Sound Effects Equalizer Mode Toggle button to toggle through
some of the equalizer options (an on-screen icon will appear to show the selected
mode). A more comprehensive list of options is available from the Equalizer dropdown list.
1.Click
2.Click Realtek HD Audio Manager (or right-click the taskbar icon and select
3.Click Digital Output (tab), click Sound Effects (tab) and then click to select an
4.Click OK to close the control panel and save the settings.
Start
, and click
and make sure you are in
Sound Manager).
option in the Equalizer drop-box.
Control Panel
Classic View
(or point to
.
Settings
and click
Control Panel
)
Figure 2 - 11
Realtek Audio
Manager -
Recording Setup
Sound Effects Equalizer
2 - 14 Audio Features
Page 57
Storage Devices, Mouse, Audio & Printer
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most new printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1.Set up the printer according to its instruction s (unpacking, p aper tr ay, toner/ink cartridge etc.).
2.Turn ON the computer.
3.Turn ON the printer.
4.Connect the printer’s USB cable to one of the USB ports on the computer.
5.Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar
(you will need to purchase a parallel to USB converter).
Parallel Printer
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
2
Adding a Printer 2 - 15
Page 58
Storage Devices, Mouse, Audio & Printer
2
2-16
Page 59
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.
This chapter covers:
•The Power Sources
•Turning on the Computer
•Power Plans
•Power-Saving States
•Configuring the Power Buttons
•Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the WindowsVista OS.)
Hibernate Mode In
Windows Vista SP1
If you are using Windows Vista SP1 with
4GBRAM installed, see
page 8 - 13 for information on Hibernate.
3
Overview 3 - 1
Page 60
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components (see page C - 4).
1.Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2.Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3.Raise the lid/LCD to a comfortable viewing angle.
4.Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery dischargecompletely before recharging (see “How do I completely discharge the battery?”
on page 3 - 14).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 10.
3 - 2 The Power Sources
Page 61
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down). Use Power Op-tions (Hardware and Sound menu) control panel in Windows Vista to configure
this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button Sleep
Sleep is the default power mode when the power button is pressed for less than 4 seconds.You may configure the options for the power button from the Power Options (Hardware
and Sound menu) control panel in Windows Vista (see your OS’s documentation, or
“Configuring the Power Buttons” on page 3 - 8 for details).
Power Management
Shut Down
Note that you should always shut your computer down by choosing the
Shut Down command
from the Lock Button
Menu in Windows Vis-
ta. This will help prevent
hard disk or system
problems.
3
Turning on the Computer 3 - 3
Page 62
Power Management
Power Plans
3
Resuming
Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
3 - 4 Power Plans
Page 63
Each WindowsPower Plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Figure 3 - 2
Power Plans
Power Plans3-5
Page 64
Power Management
Power-Saving States
3
Power Button
The Power Button
in the Start Menu (in
Classic View use the
Shut Down button )
can be used to send the
computer into a powersaving state.
Sleep Mode &
Mobile PC Battery
A mobile PC in Sleep
uses very little battery
power.
After an extended period of time the computer
will save any open documents and applications
to hard disk.
You can use power-saving states to stop the computer’s operation and restart where
you left off. Sleep is the default power-saving state in Windows Vista.
Earlier versions of Windows used Stand By and Hibernate as system power-saving
states. Windows Vista combines the features of Stand By and Hibernate into the default Sleep power-saving state.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
3 - 6 Power-Saving States
Page 65
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.
Shut Down
You should shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from shut down takes longer than
from Sleep or Hibernate.
Power Management
Silent Mode
You can use Silent
Mode to reduce power
consumption and fan
noise. Use the SilentMode Touch Sensor Instant Key to toggle
this mode on/off.
On screen visual indicators and the
Touch Sensor Instant
Key will display the
Silent Mode status (see
Table 1 - 2, on page 1 -
8).
Note Silent Mode may
reduce computer performance.
3
Figure 3 - 3
Lock Button menu
Power-Saving States 3 - 7
Page 66
Power Management
Configuring the Power Buttons
3
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 4
Power Options
Define Power
Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state.
3 - 8 Configuring the Power Buttons
Page 67
Resuming Operation
You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status
Power OffOffPress the Power Button
SleepBlinking Green
Icon Color
Press the Sleep Button (Fn + F4 Key Combo)
To Resume
Press the Power Button
Power Management
Closing the Lid
If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.
3
Hibernate
Display Turned OffGreenPress a Key or Move the Mouse/Touchpad
Off (battery)
Press the Power Button
Orange (AC/DC adapter)
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for
longer than this will force shut the computer to shut down).
Configuring the Power Buttons 3 - 9
Table 3 - 1
Resuming
Operation
Page 68
Power Management
Battery Information
3
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings
Please follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge
status.
3 - 10 Battery Information
Page 69
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
•Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
•Reduce the amount of time before the display is turned off.
•Close wireless, Bluetooth, modem or communication applications when they are
not being used.
•Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel
provides an easy point
of access for information
on battery status, power
plans used etc.
Figure 3 - 6
Windows Mobility
Center
3
Conserving Battery Power 3 - 11
Page 70
Power Management
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
3
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 14 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery Information” on page 3 - 10 for more information on how to maintain and properly
recharge the battery pack.)
3 - 12 Battery Life
Page 71
Proper handling of the Battery Pack
•DO NOT disassemble the battery pack under any circumstances.
•DO NOT expose the battery to fire or high temperatures, it may explode.
•DO NOT connect the metal terminals (+, -) to each other.
Power Management
Caution
Danger of explosion if
battery is incorrectly replaced.
3
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Battery Life3-13
Page 72
Power Management
Battery FAQ
How do I completely discharge the battery?
3
Figure 3 - 7
Power Plan Create
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1.Save and close all files and applications.
2.Create a power plan for discharging the battery and set all the options to Never.
3.Click Change plan settings (after saving it) and click Change advanced power settings.
3 - 14 Battery Life
Page 73
4.Scroll down to Battery and click + to expand the battery options.
5.Choose the options below (click Yes if a warning appears):
•Low battery levels = 0%
•Critical battery Levels = 0%
•Low battery action = Do Nothing
•Critical battery action (On battery) = Shut Down
•Critical battery action (Plugged in) = Do Nothing
Power Management
3
Figure 3 - 8
Power Options
Advanced Settings -
Battery
Battery Life3-15
Page 74
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
SLI Multi GPU Configuration & Battery Power
Note that due to the high power and system demands created by enabling SLI Configu ration, you should not enable SLI configuration if your computer is powered by batteryonly. If you attempt to run an SLI config uration when the computer is powered by the battery only, then system problems may occur.
If the computer is currently powered by battery only do not enable SLI configuration.
If you have currently enabled SLI configuration, an d the computer is powered by the AC/
DC adapter, do not switch to battery power only (or go to the NVIDIA Control Panel and
disable SLI configuration before switching to battery power only).
3 - 16 Battery Life
Page 75
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities.
RAID & AHCI Setup
Note that setting up a RAID, or AHCI mode, needs to
be done prior to installing the Windows OS, and therefore before installing the other drivers listed here (see
“Setting Up SATA RAID or AHCI Modes” on page 7
- 35).
What to Install
The Device Drivers & Utilities + User’s Manual disc
contains the drivers and utilities necessary for the
proper operation of the computer.
Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in-stalled in the orderindicated.
Module Driver Installation
The procedures for installing drivers for the WLAN,
PC Camera, Consumer Infrared (for TV tuner re-mote), and Fingerprint modules are provided in
“Modules” on page 7 - 1.
4
What to Install 4 - 1
Page 76
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-ers (button) to access the Optional driver menu.
4
Figure 4 - 1 - Drivers Installer Screen 1
1.Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2.Click to select the driver you wish to install, after
installing each driver it will become grayed out. If
you need to reinstall any driver, click the Unlock
button (you should uninstall the driver first).
3.Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
PC Camera ModulePage 7 - 38
TV Tuner ModulePage 7 - 46
Fingerprint Reader ModulePage 7 - 49
Table 4 - 1 - Driver Installation
Manual Driver Installation
Click the Browse CD/DVD button in the Drivers Installer application and browse to the executable file in
the appropriate driver folder.
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -
8 for instructions.
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1
(or a Windows Vista version which includes Service
Pack 1) before installing any drivers. Go to the Microsoft website for download details, or contact your service
center.
4
Driver Installation 4 - 3
Page 78
Drivers & Utilities
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
4
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as
outlined in this chapter.
If the driver is not listed in the Programs and Fea-tures menu:
1.Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2.Double-click Device Manager (Hardware and
Sound > Device Manager).
3.Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4.Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
User Account Control (Win Vista)
If a User Account Control prompt appears as part of
the driver installation procedure, click Continue/Al-low, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of
the driver installation process. Just click “Install thisdriver software anyway” or Install to continue the in-
stallation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” during the installation procedure (other than when out-lined in the driver install procedure), click Cancel
to close the window, and follow the installation procedure.
4 - 4 Driver Installation
Page 79
Drivers & Utilities
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
discand click Install Drivers (button), or Option Driv-ers (button) to access the Optional driver menu.
Driver Installation General Guidelines
The driver installation procedure outlined in this
Chapter (and in Chapter 7 Options & Modules),
are accurate at the time of going to press.
Drivers are always subject to upgrade and revision
so the exact procedure for certain drivers may differ
slightly. As a general guide follow the default on
screen instructions for each driver (e.g. Next > Next> Finish) unless you are an advanced user. In many
cases a restart is required to install the driver.
RAID Note: Setting up a RAID, or AHCI mode,
needs to be done prior to installing the Windows OS,
and therefore before installing the other drivers listed
here.
Chipset
1.Click 1.Install Chipset Driver > Yes.
2.Click Next> Next > Next.
3.Click > Yes.
4.Click Next> Next.
5.Click Finish to restart the computer.
6.Click Restart Now to apply the changes to the
computer.
Video
1.Click 2.Install Video Driver > Yes.
2.Click Next > Next.
3.Click Finish to restart the computer.
4
Driver Installation 4 - 5
Page 80
Drivers & Utilities
Audio Drivers
Note that two drivers are provided on the disc for the
4
Audio system.The driver included in the Drivers Installer menu has already received certification for
Windows. A second driver is included (which may
resolve some known issues with the original driver),
which at time of going to press, has not yet received
certification for Windows. Install one of the drivers
as per your preference.
Audio (Beta Version)
1.If you are in the Drivers Installer list click
Back to return to the top level of the disc.
2.Click Browse CD.
3.Browse to the following location on the Device
Drivers & Utilities + User’s Manual disc (note
that D: is the CD/DVD device drive letter,
however your system may have designated a
different device drive letter): D:\Driv-ers\Beta\Audio\setup.exe.
Audio (Drivers Installer Version)
1.Click 3. Install Audio Driver > Yes.
2.Click Next.
3.Click Finish to restart the computer.
TouchPad
1.Click 4.Install Touchpad Driver > Yes.
2.Click Next > Finish.
3.Click Restart Now to restart the computer.
Card Reader/ExpressCard
1.Click 5.Install Cardreader Driver > Yes.
2.Click Install > Finish.
GameKey Utility
1.Click 6.InstallGamekey Driver > Yes.
2.Click Next.
3.Click Finish to restart the computer.
4.See “Game Keys” on page 2 - 9 for configura-
tion instructions.
4 - 6 Driver Installation
Page 81
Hot Key Drivers
Note that two drivers are provided on the disc for the
Hot Key utility.The driver included in the Drivers In-staller menu has already received certification for
Windows. A second driver is included (which may
resolve some known issues with the original driver),
which at time of going to press, has not yet received
certification for Windows. Install one of the drivers
as per your preference.
Hot Key (Beta Version)
1.If you are in the Drivers Installer list click
Back to return to the top level of the disc.
2.Click Browse CD.
3.Browse to the following location on the Device
Drivers & Utilities + User’s Manual disc (note
that D: is the CD/DVD device drive letter, however your system may have designated a different device drive letter):
D:\Drivers\Beta\Hotkey\setup.exe.
Drivers & Utilities
Hot Key
1.Click 7.InstallHotkey Driver > Yes.
2.Click Next > Install.
3.Click Finish to restart your computer.
IEEE 1394 Filter Driver
1.Click 8.Install 1394 Filter Driver > Yes.
2.Click Install > Finish.
4
Driver Installation 4 - 7
Page 82
Drivers & Utilities
Optional Drivers
Windows Update
After installing all the drivers make sure you enable Win-
4
dows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes
from Microsoft).
To enable Windows Update make sure you are con-nected to the internet:
1.Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2.Click Check for updates (Security), or doubleclick Security Center and click Windows Update.
3.Double-click Check for updates (button).
4.The computer will now check for updates (you
need to be connected to the internet).
5.Click Install now (button) to install the updates.
See the pages indicated for the driver installation procedures for any modules included in your purchase option.
Figure 4 - 3 - Optional Drivers Installer Screen
4 - 8 Driver Installation
Page 83
Drivers & Utilities
RAID Setup
Note: Prior to setting up the RAID you will need to use
an operable computer to copy the RAID driver to a
USB flash drive before installing the Windows Vista
operating system. See “Setting Up SATA RAID or
AHCI Modes” on page 7 - 2 for configuration instruc-
tions.
Bluetooth Module
Note: The operating system is the default setting for
Bluetooth control in Windows Vista, and does not re-
quire a driver. See “Bluetooth Module” on page 7 - 16
for configuration instructions.
Wireless LAN
See the appropriate install procedure for your WLAN
module in “Wireless LAN Module” on page 7 - 20.
PC Camera
See the install procedure in “PC Camera Module” on
page 7 - 38.
Consumer Infrared (for TV Tuner Remote)
See the install procedure in “TV Tuner Module” on
page 7 - 45.
Fingerprint Reader Module
See the install procedure in “Fingerprint Reader
Module” on page 7 - 48.
4
Driver Installation 4 - 9
Page 84
Drivers & Utilities
4
4-10
Page 85
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what youare doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
Page 86
BIOS Utilities
Phoenix SecureCore(tm) Desktop
Copyright 1985-2007 Phoenix Technologies Ltd.
All Rights Reserved
BIOS Revision: ********
KBC/EC Firmware Revision: ********
CPU=1Processors Detected, Cores per Processor = 2
Intel(R) Core(TM)2 CPUP8700 @ 2.53GHz
600K System RAM Passed
1022M Extended RAM Passed
3072 KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: FUJITSU MHZ2250BH G2
ATAPI CD-ROM: TSSTcorp CDDVDW TS-L633A
Mouse intialized
Press <F2> to enter SETUP
The Power-On Self Test (POST)
POST Screen
1.BIOS information
2.CPU type
3.Memory status
5
4.Enter Setup prompt
appears only during
POST
Note: The POST screen
as pictured is for guideline purposes only.
Figure 5 - 1
POST Screen
Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
1
2
3
4
5 - 2 The Power-On Self Test (POST)
Page 87
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
•Press <F1> to resume
•<F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
BIOS Utilities
5
The Power-On Self Test (POST) 5 - 3
Page 88
BIOS Utilities
The Setup Utility
The Phoenix Setup utility tells the system how to configure itself and manage basic
features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt
5
(Press F2 to Enter Setup) seen in Figure 5 - 1 on page 5 - 2 is usually present for a
few seconds after you turn on the system. If you get a “Keyboard Error”, (usually
because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Utility
Page 89
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with menu headings. When you select a
heading, a new screen appears. Scroll through the features listed on each screen to
make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
BIOS Utilities
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
F1HelpSelect Item-/+Change ValuesF9Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
<Tab>, <Shift Tab>, or
<Enter> selects field.
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
Page 91
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
BIOS Revision/VGA Card etc. (Main Menu)
This item contains information on the BIOS version and video card etc., and is not
user configurable.
BIOS Utilities
5
Main Menu 5 - 7
Page 92
BIOS Utilities
Advanced Menu
MainAAdvancedSecurityBootExit
Figure 5 - 3
Advanced Menu
5
Installed O/S:[Windows VISTA]
SATA Mode Selection:[AHCI]
Legacy USB Support:[Enabled]
Boot-time Diagnostic Screen:[Disabled]
Power On Boot Beep[Disabled]
Battery Low Alarm Beep:[Disabled]
F1Help Select Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Installed O/S (Advanced Menu)
This setting tells the computer what kind of operating system you’re using. Make
sure you choose the correct setting for your O/S in order to prevent system problems.
Note: If you select the Vista O/S then the SATA Mode Selection menu will become
available.
Phoenix SecureCore(tm) Setup Utility
Advanced
Only available if Windows Vista
is selected as the O/S.
Item Specific Help
Select Items To
Enable/Disable
integrated devices
5 - 8 Advanced Menu
Page 93
SATA Mode Selection (Advanced Menu)
This menu is only available if you select the Vista O/S as your operating system.
You may enable/disable SATA RAID or AH CI mode for your hard disks, however
you should only enable/disable SATA RAID or AHCI BEFORE installing an
operating system, and after you have backed up all necessary files and data (see
sidebar).
Legacy USB Support: (Advanced Menu)
Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is “Enabled” and
does not need to be changed if you intend to use your USB devices in Windows.
Boot-time Diagnostic Screen: (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep:(Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities
SATA Mode
Selection
If you have installed the
Windows Vista operating system with either
AHCI or RAID mode enabled, DO NOT disable
the set mode (if you wish
to disable the set mode
you will need to reinstall
the Windows VIsta OS).
5
Advanced Menu 5 - 9
Page 94
BIOS Utilities
t
e
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
5
access to your machine as it boots up after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
Figure 5 - 4
Security Menu
MainAdvancedSSeeccuurriittyyBootExit
=
Supervisor Password Is:Clear
User Password Is:Clear
Set Supervisor Password[Enter]
Set User Password[
Password on boot:[
F1Help Select Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Set Supervisor Password (Security Menu)
You can set a password for access to the Phoenix SecureCore SetupUtility. This
will not affect access to the computer OS (only the Phoenix SecureCore SetupUtility).
Phoenix SecureCore(tm) Setup Utility
Security
sab]
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Security Menu
5 - 10 Security Menu
Page 95
Set User Password (Security Menu)
You can set a password for user mode access to the Phoenix SecureCore Setup
Utility. This will not affect access to the computer OS, (only the Setup utility) unlessyou choose to set a Password on Boot (see below). Many menu items in the Phoenix
SecureCore Setup Utility cannot be modified in user mode. You can only set the
user password after you have set the supervisor password.
Password on boot (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled”is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
BIOS Utilities
Password Warning
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
F1Help Select Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Phoenix SecureCore(tm) Setup Utility
Boot
Exit
Item Specific Help
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<x> exclude or include
the device to boot.
When you turn the computer on it will look for an operating system (e.g. Windows
Vista) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.
5 - 12 Boot Menu
Page 97
Exit Menu
BIOS Utilities
MainAdvancedSecurityBoot
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1Help Select Item-/+Change ValuesF9Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Phoenix SecureCore(tm) Setup Utility
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.
Figure 5 - 6
Exit Menu
5
Exit Menu 5 - 13
Page 98
BIOS Utilities
5
5-14
Page 99
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Battery
• Upgrading the Hard Disk Drive
• Upgrading the System Memory (RAM)
• Upgrading the Optical (CD/DVD) Device
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Page 100
Upgrading The Computer
When Not to Upgrade
Power Safety Warning
These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if:
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
6
cables (including telephone lines). It is advisable to also remove your
battery in order to prevent accidentally turning
the machine on.
6 - 2 Overview
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or re-
place the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the processor or mainboard.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.