Eurocom M570A User Manual
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©August 2005
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel®, Pentium® and Celeron® are US registered trademarks of Intel Corporation.
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and
injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and b atteries indicated in this manual. Do not d ispose of batterie s in a fire. They
may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Model A by a DC Output 20V, 4.5A minimum AC/DC Adapter and Model B by a DC Output 20V , 6.0A minimum AC/DC Adapter - see pages 1 - 3
& C - 6).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class I Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the component s could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating
element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be
badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
IV
Preface
3. A void interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working pro ced ures for the comp ute r. Shut the co mpute r down p roper ly and don ’t
forget to save your work. Remember to periodically save your data as data may be lost if the battery is
depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VI
Warning
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If yo u do not
have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head,
not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any
way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Al ways dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to disp ose of thi s battery into the mu nicip al waste
stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery ac cord i n g to the man u fa ctu re r’ s ins tru cti o ns.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD pan el breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s)
and screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’
adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for
both hardware and software. Make sure your “p apers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes whi le the computer is in
use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best po sition.
XII
Contents
Notice ...........................................................................I
FCC Statement .......................................................II
Instructions for Care and Operation .....................IV
Power Safety ........................................................VI
Battery Precautions .............................................VII
Cleaning ............................................................ VIII
Servicing ........................................................... VIII
Travel Considerations ..........................................IX
Quick Start Guide
Overview ..................................................................1-1
Model Differences ..................................................1-2
Advanced Users .....................................................1-4
Beginners and Not-So-Advanced Users .................1-4
Warning Boxes .......................................................1-4
Not Included ...........................................................1-5
System Software .....................................................1-5
System Startup ..........................................................1-6
System Map: Model A - Front View
with LCD Panel Open ..............................................1-7
System Map: Model B - Front View
with LCD Panel Open ..............................................1-8
LED Indicators ......................................................... 1-9
Preface
Ap-Key Buttons & Keyboard ................................1-10
Function Keys ........................................................ 1-11
System Map: Front View (Audio "DJ") ................ 1-12
Audio "DJ" CD Player ........................................... 1-13
System Map: Rear View ........................................ 1-14
System Map: Right View ....................................... 1-15
System Map: Left View .........................................1-16
System Map: Bottom View ....................................1-17
Windows XP Start Menu & Control Panel ............ 1-18
Video Features .......................................................1-19
Display Devices & Options .................................1-21
Power Management Features ................................. 1-22
Features & Components
Overview ..................................................................2-1
Hard Disk Drive ....................................................... 2-2
Optical (CD/DVD) Device ...................................... 2-3
Loading Discs ........................................................ 2-3
Handling CDs or DVDs ......................................... 2-4
DVD Regional Codes ............................................ 2-5
4-in-1 Card Reader ................................................... 2-6
PC Card Slot ............................................................2-7
Inserting and Removing PC Cards ........................ 2-7
XIII
Preface
Auto Mail Checker ...................................................2-8
Application Ap-Key ...............................................2-10
TouchPad and Buttons/Mouse ...............................2-11
Configuring the TouchPad and Buttons ..............2-11
Audio Features .......................................................2-12
Adding a Printer .....................................................2-13
USB Printer .........................................................2-13
Parallel Printer .....................................................2-13
Power Management
Overview ..................................................................3-1
Advanced Configuration and Power Interface .......3-1
The Power Sources ................................................. ..3-2
AC/DC Adapter ......................................................3-2
Battery ....................................................................3-2
Turning on the Computer .........................................3-3
Power Schemes ........................................................3-4
System Power Options .............................................3-6
Hibernate Mode vs. Shutdown ...............................3-6
Standby Mode vs. Hibernate Mode ........................3-6
Standby ..................................................................3-7
Hibernate ............................................................... 3-7
Configuring the Power Button .................................3-8
Battery Information ..................................................3-9
New Battery ..........................................................3-9
Battery Life ........................................................... 3-9
Recharging the Batter y with the AC/DC Adapter 3-10
Proper handling of the Battery Pack ................... 3-11
Battery FAQ ........................................................ 3-12
Drivers & Utilities
What to Install ..........................................................4-1
Module Driver Installation .................................... 4-1
Service Packs .........................................................4-3
Authorized Driver Message ................................... 4-4
Version Conflict Message ..................................... 4-4
Updating/Reinstalling Individual Drivers ............. 4-4
Driver Installation .................................................... 4-5
Driver Installation Procedure .................................4-6
New Hardware Found ............................................ 4-6
Service Pack Installation ....................................... 4-6
Chipset .................................................................. 4-7
Video(VGA) ......................................................... 4-7
Audio .................................................................... 4-8
Modem .................................................................. 4-8
LAN ...................................................................... 4-9
AP-Key Buttons ....................................................4-9
TouchPad ............................................................ 4-10
PCMCIA/Card Reader ........................................4-10
AutoMail ............................................................. 4-11
XIV
Preface
Module Drivers ....................................................4-11
Wireless LAN .....................................................4-11
Bluetooth ............................................................. 4-11
PC Camera ..........................................................4-11
TV Tuner Options ....................................... .... ....4-11
BIOS Utilities
Overview ..................................................................5-1
The Power-On Self Test (POST) .............................5-2
Failing the POST ....................................................5-3
Fatal Errors ............................................................5-3
Non-Fatal Errors ...................................................5-3
The Setup Program ...................................................5-4
Entering Setup ........................................................5-4
Setup Screens .........................................................5-5
Main Menu ...............................................................5-6
System Time & Date (Main Menu) ..........................5-6
IDE Channel 0 Master/Slave (Main Menu) .............5-7
SATA Port 1(Main Menu) .......................................5-7
System/Extended Memory: (Main Menu) ................5-7
VGA BIOS Revision: (Main Menu) ........................5-7
Advanced Menu .......................................................5-8
Advanced Chipset Control (Advanced Menu) .........5-8
National 383 SIO Control
Sub-Menu (Advanced Menu) ...................................5-9
Legacy USB Support (Advanced Menu) ................. 5-9
Boot-time Diagnostic Screen: (Advanced Menu) .... 5-9
Reset Configuration Data: (Advanced Menu) ......... 5-9
Power on Boot Beep/Battery
Low Alarm Beep: (Advanced Menu) ...................... 5-9
Security Menu ........................................................ 5-10
Set Supervisor Password (Security Menu) ............ 5-10
Password on boot: (Security Menu) .......................5-11
Boot Menu .............................................................5-12
Configuring the Network Boot Protocol ............. 5-14
Exit Menu .............................................................. 5-15
Upgrading The Computer
Overview ..................................................................6-1
When Not to Upgrade ............................................ 6-2
Removing the Battery .............................................. 6-3
Upgrading the Hard Disk Drive ............................... 6-4
Upgrading the Optical (CD/DVD) Device .............. 6-7
Upgrading the System Memory (RAM) .................. 6-8
Inserting the 2nd Hard Disk ................................... 6-11
Upgrading the Processor ........................................ 6-12
Modules & Options
Overview ..................................................................7-1
XV
Preface
Intel PRO/Wireless Mini-PCI WLAN Module ........7-2
Intel WLAN Driver Installation ............................7-3
Bluetooth Module .....................................................7-4
Bluetooth Driver Installation ................................7-4
Bluetooth Audio Setup ..........................................7-6
PC Camera Module .................................... ..............7-8
Sertek PC Camera Driver Installation (WinXP) ...7-9
PC Camera Audio Setup .....................................7-10
BisonCap ..............................................................7-12
Eliminating Screen Flicker ..................................7-13
TV Tuner Module Options .....................................7-14
LifeView FlyDVB-T Hybrid Mini-PCI
TV Tuner Module ................................................7-15
Installing the LifeView FlyDVB-T Driver .........7-15
Installing the InterVideo WinDVD 4 Software ..7-15
YUAN PVR Mini-PCI MPC622-MCE
TV Tuner Module ................................................7-16
Installing the MPC622 Driver for
Windows XP Media Center Edition (MCE) .......7-16
Troubleshooting
Overview ..................................................................8-1
Basic Hints and Tips ................................................8-2
Backup and General Maintenance ............................8-3
Viruses ...................................................................... 8-4
Upgrading and Adding New Hardware/Software .... 8-5
Problems and Solutions ........................................... 8-7
Interface (Ports & Jacks)
Overview ................................................................. A-1
Notebook Ports and Jacks ....................................... A-2
Built-In Microphone ...............................................A-2
Card Reader Port .....................................................A-2
CATV-In Jack .........................................................A-2
DVI-Out Port ..........................................................A-2
DC-In Jack ......................... .....................................A-2
Headphone-Out Jack ...............................................A-2
Line-In Jack ............................................................A-3
Microphone-In Jack ................................................A-3
Mini-IEEE 1394 Port ..............................................A-3
RJ-11 Phone Jack ....................................................A-3
RJ-45 LAN Jack ......................................................A-3
Security Lock Slot ..................................................A-4
Serial Port ...............................................................A-4
S/PDIF-Out Jack .....................................................A-4
S-Video-Out Jack ....................................................A-4
USB 2.0/1.1 Ports ...................................................A-4
XVI
Preface
ATI Video Driver Controls
ATI Video Driver Installation ................................. B-1
ATI Mobility Radeon Properties ............................. B-2
Display Devices .......................................................B-4
Attaching Other Displays ........................................ B-5
Display Modes .........................................................B-6
Clone Mode ...........................................................B-7
Enabling TV Display .............................................B-11
Specifications
Processor .................................................................C-2
Core Logic ...............................................................C-2
Memory ................................................................... C-2
Security ....................................................................C-2
BIOS ........................................................................ C-2
LCD ......................................................................... C-2
Video Card Options .................................................C-3
Storage .....................................................................C-4
Audio ....................................................................... C-4
Interface & Communication ....................................C-5
Card Reader .............................................................C-5
Keyboard & Pointing Device ..................................C-6
PCMCIA ..................................................................C-6
Power Management .................................................C-6
Power .......................................................................C-6
Environmental Spec .................................................C-6
Physical Dimensions & Weight ...............................C-6
Optional ...................................................................C-7
XVII
Preface
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 4-in-1 card reader, PC Card), Auto Mail Checker, Touch Pad & Mouse, Audio
Features & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, PC Camera and TV Tuner modules
(some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the ATI Video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Model Differences
This notebook series includes two different model types. The models differ slig htly in design style inclu ding the
LCD type, and AC/DC adapter. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline of the model
differences (Model B includes two different design types).
Model A Model B
Model A Model B
1 - 2 Overview
Model A
Model B
Design I
Figure 1 - 1 - Model Differences
Model B
Design II
Quick Start Guide
Feature Model A Model B
1
Processor Options
(See Page C - 2)
Design Types
LCD Type
Video Card
AC/DC Adapter
Pentium M & Celeron M Processor Options Pentium M Processor Options Only
1 * Design Type 2 * Design Types
15.4" WXGA (1440*900) Flat Panel TFT
OR
15.4" WSXGA+ (1680*1050) Flat Panel TFT
OR
15.4" WUXGA (1920*1200) Flat Panel TFT
ATI X700 (M26) PCI Express Video Card
(128/256 MB DDR Video RAM On Board)
Full Range AC/DC Adapter 20V, 4.5A
(90 Watts), 100~240V, 47~63Hz
17.0" WXGA (1440*900) Flat Panel TFT
OR
17.0" WSXGA+ (1680*1050) Flat Panel TFT
OR
17.0" WUXGA (1900*1200) Glare Type Flat
Panel TFT
ATI X700 (M26) PCI Express Video Card
(128 MB DDR Video RAM On Board)
OR
ATI X800 XT (M28 PRO) PCI Express Video
Card
Full Range AC/DC Adapter 20V, 6.0A
(120 Watts), 100~240V, 47~63Hz
Table 1 - 1 - Model Differences
Overview 1 - 3
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in
the this Quick Start Guide should be enough to get y ou up and running. Eventually you should try to look through
all the documentation (more detailed descriptions of the functions, setup and sy stem controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this
manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a
indicated in the margin. For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’ s features.
as
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 4 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win-
dows XP (Home & Professional Editions) / Windows XP Media Center Edition operating system.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 6. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “Driver Installation Procedure” on page 4 - 6 for installation instructions.
1
Overview 1 - 5
1
Quick Start Guide
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Move the LCD latches (one Model B design does not have latches) at the front of the computer outwards
towards the sides of the computer, and hold them in place to release the top cover.
6. Raise the lid/LCD to a comfortable viewing angle, and press the power button (make sure the Audio "DJ"
player is turned off) to turn the computer “on”.
7. Adjust the LCD panel to a comfortable viewing angle.
8. The LED indicators show the power and battery status of the computer, give notification of e-mail received, and
display information on the power status of the PC Camera, Bluetooth and Wireless LAN modules.
Shutdown
Please note that you should always shut your computer down by choosing the Turn Off Computer command from the
Start menu in Windows. This will help prevent hard disk or system problems.
1 - 6 System Startup
Quick Start Guide
System Map: Model A - Front View with LCD Panel Open
1
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices (e.g. WLAN or
Bluetooth) aboard aircraft
is usually prohibited.
Make sure any wireless
modules are OFF if you
are using the computer
aboard aircraft.
Use the appropriate function key combination (see
Table 1 - 4, on page 1 -
11) to toggle power to any
wireless modules, and
check the LED indicators
to see if any modules are
powered on or not (see
Table 1 - 2, on page 1 -
9).
1
Front View - LCD Panel Open
Figure 1 - 2
1. Optional Built-In PC Camera
2. LCD
2
3. Ap-Key Buttons
4. Power Button
5. Keyboard
6. TouchPad and Buttons
7. Audio "DJ" Controls
8. Built-In Microp hone
9. Audio "DJ" LED Display
3
4
Panel (Including LED
Indicators)
5
Audio "DJ" & Power Button
Make sure that the Audio "DJ"
6
7
7
8
9
player is off before pressing the
power button to turn the computer
on.
System Map: Model A - Front View with LCD Panel Open 1 - 7
1
Quick Start Guide
System Map: Model B - Front View with LCD Panel Open
Figure 1 - 3
Front View - LCD Panel Open
1. Optional Built-In PC Camera
2. LCD
3. Ap-Key Buttons
4. Power Button
5. Keyboard
6. TouchPad and Buttons
7. Audio "DJ" Controls
8. Built-In Microphone
9. Audio "DJ" LED Display
Panel (Including LED
Indicators)
Audio "DJ" & Power Button
Make sure that the Audio "DJ"
player is off before pressing the
power button to turn the computer
on.
1
Wireless Device
Operation Aboard
Aircraft
2
3
4
5
6
7
9
7
8
The use of any portable
electronic transmission
devices (e.g. WLAN or
Bluetooth) aboard aircraft
is usually prohibited.
Make sure any wireless
modules are OFF if you
are using the computer
aboard aircraft.
Use the appropriate function key combination (see
Table 1 - 4, on page 1 -
11) to toggle power to any
wireless modules, and
check the LED indicators
to see if any modules are
powered on or not (see
Table 1 - 2, on page 1 -
9).
1 - 8 System Map: Model B - Front View with LCD Panel Open
Quick Start Guide
1
LED Indicators
The LED indicators on the computer display helpful
information about the current status of the computer.
Table 1 - 2 - LED Indicators
Icon Color Description
Green The Computer is On
Blinking
Green
Green The AC/DC Adapter is Plugged In
Green
Green Caps Lock is Activated
Green
The Computer is In Standby Mode
Number Lock is Activated (to activate
press Fn & NumLk)
Scroll Lock is Activated (to activate
press Fn & ScrLk)
Icon Color Description
Orange The Battery is Charging
Blinking
Orange
Green The Battery is Fully Charged
Green Hard Disk Activity
Green
Green The Bluetooth Module is Powered On
Green The WLAN Module is Powered On
Blinking
Amber
The Battery has Reached Critically
Low Power Status
Second Battery Indicator
(Colors Displayed as Above)
The PC Camera Module is Powered
On
New Mail Has Arrived
LED Indicators 1 - 9
1
Quick Start Guide
Ap-Key Buttons & Keyboard
These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined
application, with one quick button press. To use the
“user-defined application Ap-Key Button”, you must
install the driver (see “AP-Key Buttons” on page 4 -
9). See “Application Ap-Key” on page 2 - 10 for con-
figuration instructions.
Table 1 - 3 - Ap-Key Buttons
Ap-Key Function
Activate the user specified application e.g.
Microsoft Word or Excel
Activate the Default Internet Program
Activate the Default E-Mail Browser
The keyboard has an embedded numerical keypad for
easy numeric data input, and features Function Keys to
allow you to change operational features instantly (see
Figure 1 - 4). Model A’s keyboard is pictured below.
Model B includes a numeric keypad on the right.
Function Keys
NumLk &
Model A Keyboard
Fn Key
Figure 1 - 4 - Keyboard
Numeric
Keypad
ScrLk Keys
Other Keyboards
If your keyboard is damaged or you just want to make
a change, you can use any standard USB keyboard.
The system will detect and enable it automatically.
However special functions/Ap-keys unique to the system’s regular keyboard may not work.
1 - 10 Ap-Key Buttons & Keyboard
Loading...