The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel and Pentium are registered trademarks of Intel Corporation.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•Re orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1.Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.
2.Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
3.Do not use the telephone to report a gas leak in the vicinity of the leak.
4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for possible special disposal instructions.
5.This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 3.25A minimum).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be
damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2.Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of
heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer
could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
vents.
IV
Preface
3.Avoid interference. Keep the computer away from high capacity transformers, electric motors, and
other strong magnetic fields. These can hinder proper performance and damage your data.
4.Follow the proper working procedures for the computer. Shut the computer down properly and
don’t forget to save your work. Remember to periodically save your data as data may be lost if the
battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5.Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord before
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
• Your AC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If you do not
have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head,
not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
VI
Preface
Battery Precautions
•Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
•Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.
•Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
•Keep the battery away from metal appliances.
•Affix tape to the battery contacts before disposing of the battery.
•Do not touch the battery contacts with your hands or metal objects.
Battery Disposal
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of
its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in your area for recycling options or proper
disposal.
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.Check that the battery pack and any spares are fully charged.
2.Power off the computer and peripherals.
3.Close the display panel and make sure it’s latched.
4.Disconnect the AC adapter and cables. Stow them in the carrying bag.
5.The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
However, check with your travel agent to see if you need any socket adapters.
6.Put the notebook in its carrying bag and secure it with the bag’s straps.
7.If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those
devices’ adapters and/or cables.
8.Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership
for both hardware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the vents/intakes to be blocked. To prevent
your computer from overheating make sure nothing blocks the vent/fan intake while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
•Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
•Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
•Use a chair with a back and adjust it to support your lower back comfortably.
•Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.
•Take periodic breaks if you are using the computer for long periods of time.
Remember to:
•Alter your posture frequently.
•Stretch and exercise your body several times a day.
•Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
•Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
•Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
•Position the display directly in front of you at a comfortable viewing distance.
•Adjust the display-viewing angle to find the best position.
This manual refers to the hardware and essential software required to run your
computer. Depending on how your system is configured, some or all of the
features described may already be set up. This chapter covers:
•The Manual— how to use it
•System Map— navigating around your computer
Advanced Users
If you are an advanced user you may skip over most of this manual. However
you may find it useful to refer to the
Utilities” on page 5 - 1 and
may also find the notes marked with a
“Upgrading The Computer” on page 6 - 1. You
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them)
then you should try to look through all the documentation. Do not worry if you
do not understand everything the first time. Keep this manual nearby and refer
to it to learn as you go. You may find it useful to refer to the notes marked with
a
as indicated in the margin.
“What to Install” on page 4 - 2,“BIOS
of interest to you.
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Overview 1 - 1
1
Introduction
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and
handling instructions as indicated in the
Preface.
Not Included
Operating Systems (e.g. Windows 2000 Professional, Windows XP etc.) have
their own manuals, as do applications (e.g. word processing, spreadsheet and
database programs). If you have questions about the operating systems or programs then please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where
this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the following operating systems:
•Microsoft Windows 2000
•Microsoft Windows XP (Home & Professional Editions)
1 - 2 Overview
Quick Start Guide
This guide assumes that you are already familiar with computers and can tell
at a glance what and where all the key components are. If you are not that comfortable with this type of device, then please refer to the following pages,
which give an overview of the system.
It is still best to review these steps, before taking any action. If there is anything you are not sure about, then please refer to the appropriate chapter before
continuing.
Unless you need to install an operating system, your computer should be ready
to work right out of the box. Before you begin please follow the safety instructions in the Preface.
1.Remove all packing materials.
2.Securely attach any peripherals you want to use with the computer (e.g.
keyboard and mouse) to their ports.
3.Attach the AC adapter to the DC-in jack on the right of the computer (see
“Right Side View” on page 1 - 14), then plug the AC power cord into an
outlet, and connect the AC power cord to the AC adapter.
4.Raise the lid/LCD to a comfortable viewing angle.
5.Press the power button to turn “On”.
Introduction
Peripheral Devices
Please note that peripherals (printers, digital cameras, etc.)
which attach to your
computer by either
USB or IEEE1394
ports may be connected after Windows is
up and running. All other peripherals must be
connected before you
turn on the system.
1
Quick Start Guide 1 - 3
1
Introduction
System Map
Your computer has a lot of built-in features. Most of these are enabled by your
operating system. Further explanations of the various subsystems are covered
in the chapter or pages indicated.
Getting to Know Your Computer
The following graphics will help you to become familiar with the basic functions, and to learn the location of the various ports and components of your
computer.
1 - 4 System Map
Top View
2
11
To open the LCD display:
1.Place the computer on a stable surface.
2.Move the LCD latches in the direction of the arrows to release the top
cover (the left latch will lock in position and is clearly marked with locked
and unlocked icons).
3.Lift the top cover to reveal the LCD panel and keyboard.
4.Adjust the LCD panel to a comfortable viewing angle.
5.The LED indicators show the power and battery status of the computer,
and give notification of e-mail received.
1
2
Introduction
Figure 1 - 1
Top View with LCD
Panel Closed
1.LCD Latches
2.LED Power &
Communication
Indicators
1
Top View 1 - 5
1
Introduction
Top View with LCD Panel Open
Figure 1 - 2
Top View with LCD
Panel Open
1.Optional Built-In PC
Camera
2.LCD
3.LED Power &
Communication
Indicators
4.Speakers
5.Close Cover Switch
6.LED Status
Indicators
7.Power Button
8.Keyboard
9.Built-In Microphone
10. TouchPad and
Buttons
11. Hot-Key Buttons
4
4
9
1
2
3
8
10
5
4
6
7
4
1 - 6 Top View
11
PC Camera
If you have purchased the optional PC Camera, make sure you install the software application (see “PC Camera” on page 7 - 12). The Module ON/OFF
Button will enable/disable the PC Camera (see “Module ON/OFF Button”
on page 1 - 10).
LCD Panel
The computer comes with a wide screen TFT (Thin Film Transistor), Liquid
Crystal Display screen (see “LCD” on page A - 1 for details).
LED Power & Communication Indicators
These indicators display the system power status, and battery status of the
computer. The third indicator may be configured to give a visual confirmation
when e-mail is received in the default e-mail program (see “LED Power &
Communication Indicators” on page 2 - 6).
Stereo Speakers
The built-in speakers provide rich, stereo sound.
Introduction
1
Top View 1 - 7
1
Introduction
Close Cover Switch
This switch acts as a sensor to tell when the LCD Panel is closed. When this
LCD cover sensor is activated the default setting of your operating system’s
power scheme sends the computer into a power saving state (see Figure 3 - 16
on page 3 - 27).
LED Status Indicators
These display the system’s operational status. Refer to “LED Status Indica-
tors” on page 2 - 5 for more information on what the lights mean.
Power Button
Press this button to turn your computer on or off (see “Turning on the
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination
doesn’t work, press the
power button for 4 sec-onds, or longer, to
force the system to
turn itself off.
Computer” on page 2 - 4).
key, once configured as such in the power management control panel of your
operating system (see “Configuring the Power Button” on page 3 - 27).
Please note that you should always shut your computer down by choosing the Shut
Down/Turn Off Computer command from the Start menu in Windows. This will
help prevent hard disk or system problems.
This button may also be used as a suspend/resume
Shutdown
1 - 8 Top View
Keyboard
The computer has a “Win Key” keyboard including a numeric keypad. It has
the same features as a full-sized desktop keyboard and can easily be replaced
with a different language keyboard should you desire.
Microphone
Record on your computer with the built-in microphone.
TouchPad & Buttons
The pointing device features a sensitive glide pad for precise movements. It
functions the same way as a two-button mouse. The right TouchPad button is
the same as the right mouse button; the left TouchPad button is the same as
the left mouse button. The central button may be used to scroll up and down,
or may be configured to perform a variety of functions (see “Configuring the
TouchPad and Buttons” on page 2 - 20).
Hot-Key Buttons
The three hot-keys allow you instant access to your default Internet browser
and default e-mail program, and to toggle on/off the modules (Wireless LAN/
Bluetooth/PC Camera modules). To learn how to set the buttons, see “Hot-
Key Buttons” on page 2 - 16.
Introduction
1
Top View 1 - 9
1
Introduction
Figure 1 - 3
Front View
1.LCD Latches
2.Hot-Key Buttons
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make
sure the module(s) are
OFF if you are using
the computer aboard
aircraft. When your
computer ‘Boots Up’
the modules will be
ON.
Front View
1
2
Hot-Key Buttons
The three hot-keys allow you instant access to your default Internet browser
and default e-mail program, and to toggle on/off the Wireless LAN/Bluetooth/
PC Camera modules. To learn how to set the buttons, see “Hot-Key Buttons”
on page 2 - 16.
Module ON/OFF Button
You can use this button to toggle the power ON/OFF for the 802.11b Wireless
LAN module, the optional Bluetooth module and the optional PC Camera
module. To enable the modules you will need to install the drivers/software
for them (see “Intel PRO 2100 Mini PCI Wireless LAN Module” on page 7
- 2, “Bluetooth Module” on page 7 - 7 & “PC Camera” on page 7 - 12).
Make sure the wireless modules are OFF when you are using the computer aboard aircraft (see sidebar).
1
1 - 10 Front View
Loading...
+ 144 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.