Eurocom M350C, M360C Service Manual
Notebook Computer
M350C/M360C
Service Manual
Preface
Preface
I
Preface
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained
herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are
they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or
reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of
their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement
of that product or its manufacturer.
Version 1.0
July 2003
Trademarks
Intel® and Pentium® are registered trademarks of Intel Corporation.
Windows® is a registered trademark of Microsoft Corporation.
Other brand and product names are trademarks and./or registered trademarks of their respective companies.
II
About this Manual
This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and
inspection of personal computers.
It is organized to allow you to look up basic information for servicing and/or upgrading components of the M350C/
M360C series notebook PC.
The following information is included:
Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade
elements of the system.
Preface
Appendix A, Part Lists
Appendix B, Schematic Diagrams
Appendix C, Updating the FLASH ROM BIOS
Preface
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 3.25A).
CAUTION
Preface
IV
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Preface
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This
is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface which will block
the vents.
3. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save
your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
Do not disassemble the computer by yourself.
Perform routine maintenance
on your computer.
Preface
V
Preface
4. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag-
netic fields. These can hinder proper performance and damage your data.
5. Take care when using peripheral devices.
Preface
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
Use only approved brands of
peripherals.
Unplug the power cord before
attaching peripheral devices.
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are
unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do
not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies.
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
VI
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service
personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode
or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of
its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in your area for recycling options or proper
disposal.
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Preface
Preface
VII
Preface
Preface
Related Documents
You may also need to consult the following manual for additional information:
User’s Manual on CD
This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup program. It also describes the installation and operation of the utility programs provided with the notebook PC.
VIII
Contents
Preface
Introduction ..............................................1-1
Overview .........................................................................................1-1
System Specifications .....................................................................1-2
Processor Options ............................................................................ 1-2
Core Logic .......................................................................................1-2
Structure ..........................................................................................1-2
Security ............................................................................................1-2
Memory ...........................................................................................1-2
BIOS ................................................................................................1-2
LCD .................................................................................................1-2
Display ............................................................................................1-2
Storage .............................................................................................1-2
PC Card ........................................................................................... 1-2
Audio ...............................................................................................1-2
Keyboard .........................................................................................1-3
Interface ...........................................................................................1-3
Communication ...............................................................................1-3
Power Management .........................................................................1-3
Power ...............................................................................................1-3
Indicators ......................................................................................... 1-3
Buttons ............................................................................................1-3
Environmental Spec ........................................................................1-4
Physical Dimensions .......................................................................1-4
Weight .............................................................................................1-4
Optional ...........................................................................................1-4
Design Differences .......................................................................... 1-4
External Locator - Top View ..........................................................1-5
External Locator - Front & Left Side Views ...................................1-6
External Locator - Right Side & Rear Views .................................. 1-7
External Locator - Bottom View ..................................................... 1-8
Mainboard Overview - Top (Key Parts) ......................................... 1-9
Mainboard Overview - Bottom (Key Parts) ................................. 1-10
Mainboard Overview - Top (Connectors) .................................... 1-11
Mainboard Overview - Bottom (Connectors) ............................... 1-12
Disassembly ...............................................2-1
Overview ......................................................................................... 2-1
Maintenance Tools .......................................................................... 2-2
Connections .................................................................................... 2-2
Maintenance Precautions ................................................................ 2-3
Disassembly Steps .......................................................................... 2-4
Removing the Battery ..................................................................... 2-7
Removing the Hard Disk Drive and Wireless LAN ....................... 2-8
Removing the System Memory (RAM) ....................................... 2-10
Removing the CD Device ............................................................. 2-12
Removing the Modem .................................................................. 2-13
Removing the Processor ............................................................... 2-14
Removing the Keyboard ............................................................... 2-16
Removing the Bottom Case .......................................................... 2-17
Removing the Audioboard ............................................................ 2-18
Removing the Multi-function board ............................................. 2-19
Removing the Mainboard ............................................................. 2-20
Removing the TouchPad and Click Board ................................... 2-21
Removing the Inverter .................................................................. 2-22
Removing the Speakers ................................................................ 2-23
Removing the LCD Panel ............................................................. 2-24
Removing the PC Camera Module ............................................... 2-24
Part Lists ..................................................A-1
Part List Illustration Location ........................................................ A-2
Top (M350C) ................................................................................. A-3
Preface
IX
Preface
Bottom (M350C) ............................................................................A-4
LCD (M350C) ................................................................................ A-5
CD-ROM Drive - QSI (M350C) .................................................... A-6
CD-ROM Drive - SAMSUNG (M350C) ....................................... A-7
CD-RW Drive - KME (M350C) ....................................................A-8
CD-RW Drive - TEAC (M350C) ................................................... A-9
Combo Drive - QSI (M350C) ......................................................A-10
Combo Drive - TEAC-SAMSUNG (M350C) .............................A-11
DVD-ROM Drive - QSI (M350C) ...............................................A-12
DVD-ROM Drive - TEAC (M350C) ........................................... A-13
Top (M360C) ................................................................................ A-14
Bottom (M360C) ..........................................................................A-15
LCD (M360C) ..............................................................................A-16
CD-ROM Drive - QSI (M360C) .................................................. A-17
CD-ROM Drive - SAMSUNG (M360C) .....................................A-18
CD-RW Drive - KME (M360C) ..................................................A-19
Preface
CD-RW Drive - TEAC (M360C) ................................................. A-20
Combo Drive - QSI (M360C) ......................................................A-21
Combo Drive - TEAC-SAMSUNG (M360C) .............................A-22
DVD-ROM Drive - QSI (M360C) ...............................................A-23
DVD-ROM Drive - TEAC (M360C) ........................................... A-24
Schematic Diagrams................................. B-1
LVDS; CRT ..................................................................................B-11
ICH4-1 (1 of 3) .............................................................................B-12
ICH4-2 (2 of 3) .............................................................................B-13
ICH4-3 (3 of 3) .............................................................................B-14
USB 2.0, Wireless LAN ...............................................................B-15
MDC, BT, CCT ............................................................................B-16
HDD, CDROM .............................................................................B-17
LAN RTL8100BL ........................................................................B-18
ROM, W517 .................................................................................B-19
TI1394 (TSB43AB21) ..................................................................B-20
Hitachi H8S ..................................................................................B-21
CON ..............................................................................................B-22
Audio Codec ALC201 ..................................................................B-23
PCMCIA (ENE1410) ....................................................................B-24
PCMCIA Socket ...........................................................................B-25
AC IN; Power Button ...................................................................B-26
CH7011; TV-Out ..........................................................................B-27
V_CORE .......................................................................................B-28
Charger .........................................................................................B-29
Multi-Function Board ...................................................................B-30
Updating the FLASH ROM BIOS......... C-1
System Block Diagram ................................................................... B-2
Socket 479 - 1 of 2 ......................................................................... B-3
Socket 479 - 2 of 2 ......................................................................... B-4
Montara GM-1 ................................................................................ B-5
Montara GM-2 ................................................................................ B-6
Montara GM-3 ................................................................................ B-7
DDRAM ......................................................................................... B-8
DDR Termination ........................................................................... B-9
Clock Generator ........................................................................... B-10
X
1: Introduction
Overview
This manual covers the information you need to service or upgrade the M350C/M360C series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information
about drivers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer.
Operating systems (e.g. DOS, Windows 9x, Windows NT 4.0, Windows 2000, Windows XP, OS/2 Warp, UNIX, etc.) have
their own manuals as do application software (e.g. word processing and database programs). If you have questions about
those programs, you should consult those manuals.
The M350C/M360C series notebook is designed to be upgradeable. See “Disassembly” on page 2 - 1 for a detailed description of the upgrade procedures for each specific component. Please note the warning and safety information indicated by the “” symbol.
The balance of this chapter reviews the computer’s technical specifications and features.
Introduction
1.Introduction
Overview 1 - 1
Introduction
1.Introduction
System Specifications
Processor Options
• Mobile Intel Pentium 4 Processor-M
- (478-pin) uFC-PGA package
(
µ0.13) 0.13 Micron Process Technology,
- 1.3/ 1.4/ 1.5/ 1.6/ 1.7 GHz
Core Logic
• Intel 855GM + ICH4-M
Structure
• PC2001 Compliant
• PCI 2.2 Compliant
• ACPI 2.0 Compliant
Security
• Security (Kensington® Type) Lock Slot
• BIOS Password
LCD
• 14.1" XGA Flat Panel TFT (1024*768)
Display
• Dynamic Video Memory Technology
• 128 bit 2D/3D Graphics Engine
• Motion Compensation for DVD Accelerator
• Fully DirectX 7/8 Compliant Graphics Engine
• Supports VESA DDCI, DDC2B and DDC 3.0 Specifications
Storage
• One changeable 12.7mm(h) optical Drive
• Easy changeable 2.5" 9.5 mm (h) HDD
Supports Master Mode IDE
Supports LBA Mode
Supports PIO Mode 4
ATA-33/66/100
Memory
• Two 200-pin SODIMM sockets, supporting DDR modules
• Memory expandable up to 1GB (128/ 256/ 512 MB DDR
modules)
BIOS
• One 512KB Flash ROM
• Insyde BIOS, Plug and Play (1.0a)
1 - 2 System Specifications
PC Card
• One Type-II PCMCIA 3.3V/5V Socket
Audio
• AC’97 2.2 Compliant
• Advanced Wavetable Synthesizer
• DirectSound™ 3D Accelerator
• Full-duplex
• Virtual AC3
• Built-In Microphone
• 2 Built-In Speakers
Introduction
Keyboard
• A4 Size Win 95 Keyboard (3mm travelling)
• Built-In TouchPad with Scrolling Function
Interface
• Two USB 2.0 Ports
• One Mini- IEEE 1394 Port
• One External CRT Monitor Port
• One Headphone-Out Jack
• One Microphone-In Jack
• One S/P DIF Output Jack
• One TV-Out Jack
• One RJ-11 Jack for Plug & Play Fax/Modem
• One RJ-45 Jack for 10M/ 100M Fast Ethernet
• One DC-in jack
Communication
• 56K Plug & Play Fax/Modem V.90/92 Compliant
• 10M/100M Fast Ethernet (IEEE 802.3 and 802.3u
Standard Compliant)
• CMOS Camera with USB Interface
• INTEL PRO/Wireless LAN 2100 module with Mini-PCI
interface
• Bluetooth 1.1 with MDC Interface (optional)
Power Management
• Supports ACPI 2.0
• Soft Off by system Power Button
• Supports Suspend to disk
• Supports Suspend to RAM
• Supports Battery Low Suspend
• Supports Resume From Alarm Time
• Supports Resume From Modem Ring
• Supports Wake on LAN
Power
• Full Range AC Adapter
AC-Input 100~240V, 47~63Hz
DC Output 20V, 3.25A (65W)
• 1st Smart Lithium-Ion (6 cells)
• 2nd Smart Lithium-Ion (12 cells) - optional
Indicators
• LED Indicators (Power/Suspend, Battery, HDD/CD-ROM,
Num Lock, Caps Lock, Scroll Lock, E-Mail, 802.11b &
Bluetooth)
Buttons
•E-Mail
• Internet Browser
•Power
• On/Off Switch for optional 802.11b & Bluetooth
1.Introduction
System Specifications 1 - 3
Introduction
Figure 1
1.Introduction
Design Differences
Environmental Spec
• Temperature
Operating: 5
Non-Operating: -20
• Relative Humidity
Operating: 20% ~ 80%
Non-Operating: 10% ~ 90%
°C ~ 35°C
°C ~ 60°C
Physical Dimensions
• 312mm (w) * 273mm (d) * 27.5mm (h) Min
Weight
• 2.2kg without Battery Pack
Optional
• 1st Smart Lithium-Ion (48Watt) Battery Pack
• 802.11b Module with Mini-PCI Interface
• Bluetooth 1.1 MDC Module
• 2.5" 12.5/12.7mm Height Hard Disk Drive
• 1st Smart Lithium-Ion (96Watt) Battery Pack
Design Differences
This manual refers to the two notebook designs pictured below. The designs vary slightly in external design. Photographs
used throughout this manual are of Design I.
1 - 4 System Specifications
Design I
Design II
Introduction
External Locator - Top View
4 4
Figure 2
Top View
1
1. Built-In CMOS
Camera
2. LCD
3. LED Power &
2
3
5
6
7
Communication
Indicators
4. Speakers
5. Close Cover
Switch
6. LED Status
Indicators
7. Power Button
8. Keyboard
9. Built-In
Microphone
10. TouchPad and
Buttons
11. Hot-Key Buttons
1.Introduction
8
9
10
11
External Locator - Top View 1 - 5
Introduction
Figure 3
Front View
1. LCD Latches
2. Hot-Key Buttons
Figure 4
Left Side View
1.Introduction
1. Vent
2. External Monitor
(CRT) Port
3. S-Video-Out Port
4. RJ-11 Phone Jack
5. RJ-45 LAN Jack
6. 2 * USB 2.0 Ports
7. IEEE 1394 Port
8. PC Card Slot
Eject Button
9. PC Card Slot
External Locator - Front & Left Side Views
1
2
1
2 4 5 6 7
3
1
8
9
1 - 6 External Locator - Front & Left Side Views
External Locator - Right Side & Rear Views
Introduction
Figure 5
Right Side View
1 2 3
4
5
1. Microphone-In
Jack
2. Headphone-Out
Jack
3. S/P DIF Out Port
4. CD Device Bay
5. DC-In Jack
1.Introduction
Figure 6
Rear View
1
2
1. Security Lock Slot
2. Vent
External Locator - Right Side & Rear Views 1 - 7
Introduction
Figure 7
Bottom View
External Locator - Bottom View
1. Vent/Fan Intakes
2. Battery
3. CPU Cover
4. RAM & Modem
Cover
5. CD Device
Removal Cover
6. Hard Disk &
WLAN Cover
Note: The RAM
cards are located under the RAM & Modem Cover while the
1.Introduction
optional Wireless
LAN module is located under the Hard
Disk Cover.
2
1
3
5
1
4
1 - 8 External Locator - Bottom View
6
Introduction
Mainboard Overview - Top (Key Parts)
6
5
4
3
Figure 8
Mainboard Top
Key Parts
1. PC Card
Assembly
2. LAN Controller
RTL8100BL
3. Southbridge Intel 82801DB
4. Northbridge Intel 82852GM
5. H8 Keyboard
Controller
7
6. TV-Out Controller
7. V-Core Power IC
8. Super I/O
Winbond 83517
1.Introduction
2
1
8
Mainboard Overview - Top (Key Parts) 1 - 9
Introduction
Figure 9
Mainboard Bottom
Key Parts
1. Memory Sockets
(no memory
installed)
2. CPU Socket (no
CPU installed)
3. Clock Generator
4. BIOS EEPROM
5. LAN Transformer
6. CardBus ENE
1410
7. 1394 PHY
TSB41LV01
8. ALC202 - Audio
Codec
9. Audio Amplifier
1.Introduction
Mainboard Overview - Bottom (Key Parts)
2
3
4
1 - 10 Mainboard Overview - Bottom (Key Parts)
5
1
6
9
8
7
Introduction
Mainboard Overview - Top (Connectors)
2
1
Figure 10
Mainboard Top
Connectors
1. TouchPad Cable
Connector (JTP1)
2. Keyboard
Connector (JKB1)
1.Introduction
Mainboard Overview - Top (Connectors) 1 - 11
Introduction
Figure 11
Mainboard Bottom
Connectors
1. Battery Connector
(JBATT1)
2. RTC (JBAT1)
3. Power Cable Connector
(JPWR1)
4. Multi-function Board
Cable Connector
(JMFC1)
5. CD-ROM Connector
(JCD1)
6. Hard Disk Connector
(JHDD1)
7. Wireless LAN Cable
Connector (JWLAN1)
8. Audio Board Cable
Connector (JAUDIO1)
9. Int. MIC (JMIC1)
10. 1394 Connector
1.Introduction
11. USB Connector (JUSB1
& JUSB2)
12. Int. Speaker Cable
Connector (JSPK1)
13. LAN Connector
(JMLAN1)
14. Modem Cable Connector
(JMODEM1)
15. TV-Out Connector
(JSVIDEO1)
16. VGA-Out Connector
(JVGA1)
17. Inverter Connector
(JINV1)
18. LCD (LVDS) Connector
(JLCD1)
19. Fan Cable Connector
(JFAN1 & JFAN2)
20. Modem Connector
(JMDC1)
Mainboard Overview - Bottom (Connectors)
1
2
3
4
5
6
7 8 9
19
19
18
20
17
16
15
14
13
12
11
11
10
1 - 12 Mainboard Overview - Bottom (Connectors)
2: Disassembly
Overview
This chapter provides step-by-step instructions for disassembling the M350C/M360C series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated).
We suggest you completely review any procedure before you take the computer apart.
Disassembly
Procedures such as upgrading/replacing the RAM, CD device and hard disk are included in the User’s Manual but are
repeated here for your convenience.
To make the disassembly process easier each section may have a box in the page margin. Information contained under
the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a
lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the disassembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previous disassembly procedure. The amount of screws you should be left with will be listed here also.
A box with a will also provide any possible helpful information. A box with a contains warnings.
An example of these types of boxes are shown in the sidebar.
2.Disassembly
Information
Warning
Overview 2 - 1
Disassembly
2.Disassembly
NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the
battery is removed too).
Maintenance Tools
The following tools are recommended when working on the notebook PC:
• M3 Philips-head screwdriver
• M2.5 Philips-head screwdriver (magnetized)
• M2 Philips-head screwdriver
• Small flat-head screwdriver
• Pair of needle-nose pliers
• Anti-static wrist-strap
Connections
Connections within the computer are one of four types:
Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to
gently pry the locking collar away from its base. When replacing the connection, make sure the connector is oriented in the
same way. The pin1 side is usually not indicated.
2 - 2 Overview
Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently
rock it from side to side as you pull it out. Do not pull on the
wires themselves. When replacing the connection, do not try to
force it. The socket only fits one way.
Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-
ers to gently lift the connector away from its socket. When replacing the connection, make sure the connector is oriented in
the same way. The pin1 side is usually not indicated.
Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as
you pull them apart. If the connection is very tight, use a small
flat-head screwdriver - use just enough force to start.
Maintenance Precautions
The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions:
1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other
components could be damaged.
2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight.
3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong mag-
netic fields. These can hinder proper performance and damage components and/or data. You should also monitor
the position of magnetized tools (i.e. screwdrivers).
4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly
damaged.
5. Be careful with power. Avoid accidental shocks, discharges or explosions.
•Before removing or servicing any part from the computer, turn the computer off and detach any power supplies.
•When you want to unplug the power cord or any cable/wire, be sure to disconnect it by the plug head. Do not pull on the wire.
6. Peripherals – Turn off and detach any peripherals.
7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity.
Before handling any part in the computer, discharge any static electricity inside the computer. When handling a
printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that
you use an anti-static wrist strap instead.
8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands produce oils which can attract corrosive elements.
9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted
to charged surfaces, reducing performance.
10. Keep track of the components. When removing or replacing any part, be careful not to leave small parts, such as
screws, loose inside the computer.
Disassembly
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
2.Disassembly
Cleaning
Do not apply cleaner directly to the computer, use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Overview 2 - 3
Disassembly
Disassembly Steps
The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM
THE DISASSEMBLY STEPS IN THE ORDER INDICATED.
2.Disassembly
To remove the Battery:
1. Remove the battery page 2 - 7
To remove the HDD & WLAN:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
To remove the System Memory:
1. Remove the battery page 2 - 7
2. Remove the system memory page 2 - 10
To remove the CD Device:
1. Remove the battery page 2 - 7
2. Remove the CD device page 2 - 12
To remove the Modem:
1. Remove the battery page 2 - 7
2. Remove the modem page 2 - 13
To remove the Processor:
To remove the Keyboard:
1. Remove the battery page 2 - 7
2. Remove the keyboard page 2 - 16
To remove the Bottom Case:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the system memory page 2 - 10
4. Remove the CD device page 2 - 12
5. Remove the processor page 2 - 14
6. Remove the bottom case page 2 - 17
To remove the Audioboard:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the CD device page 2 - 12
4. Remove the processor page 2 - 14
5. Remove the bottom case page 2 - 17
6. Remove the audioboard page 2 - 18
1. Remove the battery page 2 - 7
2. Remove the processor page 2 - 14
2 - 4 Disassembly Steps
Disassembly
To remove the Multi-function board:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the CD device page 2 - 12
4. Remove the processor page 2 - 14
5. Remove the bottom case page 2 - 17
6. Remove the multi-function board page 2 - 19
To remove the Mainboard:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the system memory page 2 - 10
4. Remove the CD device page 2 - 12
5. Remove the modem page 2 - 13
6. Remove the processor page 2 - 14
7. Remove the keyboard page 2 - 16
8. Remove the bottom case page 2 - 17
9. Remove the audioboard page 2 - 18
10. Remove the multi-function board page 2 - 19
11. Remove the mainboard page 2 - 20
To remove the TouchPad & Click Board:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the system memory page 2 - 10
4. Remove the CD device page 2 - 12
5. Remove the modem page 2 - 13
6. Remove the processor page 2 - 14
7. Remove the keyboard page 2 - 16
8. Remove the bottom case page 2 - 17
9. Remove the audioboard page 2 - 18
10. Remove the multi-function board page 2 - 19
11. Remove the mainboard page 2 - 20
12. Remove the touchpad & click board page 2 - 21
To remove the Inverter:
1. Remove the battery page 2 - 7
2. Remove the inverter page 2 - 22
To remove the Speakers:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the CD device page 2 - 12
4. Remove the processor page 2 - 14
5. Remove the bottom case page 2 - 17
6. Remove the multi-function board page 2 - 19
7. Remove the mainboard page 2 - 20
8. Remove the inverter page 2 - 22
9. Remove the speakers page 2 - 23
2.Disassembly
Disassembly Steps 2 - 5
Disassembly
2.Disassembly
To remove the LCD Panel:
1. Remove the battery page 2 - 7
2. Remove the HDD & WLAN page 2 - 8
3. Remove the CD device page 2 - 12
4. Remove the processor page 2 - 14
5. Remove the bottom case page 2 - 17
6. Remove the multi-function board page 2 - 19
7. Remove the inverter page 2 - 22
8. Remove the LCD panel page 2 - 24
To remove the PC Camera:
1. Remove the battery page 2 - 7
2. Remove the inverter page 2 - 22
3. Remove the PC Camera page 2 - 24
2 - 6 Disassembly Steps
Removing the Battery
Disassembly
1. Turn the computer off, and turn it over.
2. Locate the battery release latch
1
3. Latch
4. Slide the Battery out (Figure 1c).
a.
should slide to the left, and you will need to hold it in place (Figure 1b).
2
1
1
(Figure 1a).
b.
c.
Figure 1
Battery Removal
a. Locate the battery re-
lease latch.
b. Slide the latch to the left
and hold.
c. Slide the battery out.
2
2.Disassembly
2. Battery
Removing the Battery 2 - 7
Loading...