EUROCOM M190S World Warrior User Manual
I
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©February 2003
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel and Pentium are registered trademarks of Intel Corporation.
II
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance
with the above standards could void your authority to operate the equipment.
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example near a bathtub, washbowl, kitchen sink or laundry tub, in
a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for possible special disposal instructions.
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
IV
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be
damaged.
2. Keep it dry, and don’t overheat it, and. Keep the computer and power supply away from any kind
of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface which will block
the vents.
V
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and
other strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working procedures for the computer. Shut the computer down properly and
don’t forget to save your work. Remember to periodically save your data as data may be lost if the
battery is depleted.
5. Take care when using peripheral devices.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
Do not disassemble the computer by yourself.
Perform routine maintenance
on your computer.
Use only approved brands of
peripherals.
Unplug the power cord before
attaching peripheral devices.
VI
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If you do not
have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head,
not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VII
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of
its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in your area for recycling options or proper
disposal.
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
VIII
Preface
Cleaning
Do not apply cleaner directly to the computer, use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
IX
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC adapter and cables. Stow them in the carrying bag.
5. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those
devices’ adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership
for both hardware and software. Make sure your “papers” are handy (it may be useful to have the
computer in a sleep mode before going through customs).
X
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook: For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields: Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely: Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment,
make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can: If an electrical outlet is available, use the AC adapter and keep your battery(ies) charged.
Keep it dry: If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
XI
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display viewing angle to find the best position.
XIII
Preface
Contents
Trademarks ......................................................... I
FCC Statement ..................................................II
Instructions for Care and Operation ................ IV
Power Safety .................................................... VI
Battery Precautions .........................................VII
Cleaning ........................................................VIII
Servicing ........................................................VIII
Travel Considerations ...................................... IX
Introduction ..................................1-1
Overview ..................................................................1-1
Advanced Users ..................................................1-1
Beginners and Not-So-Advanced Users .............1-1
Warning Boxes ...................................................1-2
Not Included .......................................................1-2
System Software .................................................1-2
Quick Start Guide .....................................................1-3
CDMA or GPRS Modem Operation ........................1-4
CDMA ............................................................1-4
GPRS ..............................................................1-4
Turning the Modem OFF & ON ....................1-4
System Map ..............................................................1-5
Getting to Know Your Computer .......................1-5
Top View ............................................................ 1-6
Front View ......................................................... 1-7
LCD Panel ...................................................... 1-8
LED Status Indicators .................................... 1-8
Close Cover Switch ....................................... 1-8
Power Button ................................................. 1-9
Built-In Microphone ...................................... 1-9
Keyboard ........................................................ 1-9
Speakers ....................................................... 1-10
Hot-Keys ...................................................... 1-10
TouchPad & Buttons .................................... 1-10
LED Power & Communication Indicators ... 1-10
SPDIF Out Port ............................................ 1-10
Microphone-In Jack ..................................... 1-11
Headphone-In Jack ...................................... 1-11
Infrared Transceiver ..................................... 1-11
Built-In Telecom Microphone ..................... 1-11
Left Side View ................................................. 1-12
Antenna ........................................................ 1-13
External Monitor Port .................................. 1-13
DC-In Jack ................................................... 1-13
PS/2 Type Port ............................................. 1-13
Telephone Headset Jack ............................... 1-13
External IDE Port ......................................... 1-13
Mini - IEEE 1394 Port ................................. 1-14
XIV
Preface
PC Card Slot .................................................1-14
Right Side View ................................................1-15
Hard Disk Drive ...........................................1-16
Dual USB 2.0 Ports ......................................1-16
RJ-11 Phone Jack .........................................1-17
RJ-45 LAN Jack ...........................................1-17
Vent ..............................................................1-17
Rear & Bottom Views ......................................1-18
Security Lock ...............................................1-18
Using The Computer ...................2-1
Overview ..................................................................2-1
The Power Sources ...................................................2-2
AC Adapter .........................................................2-2
Battery ................................................................2-3
Recharging Battery with the AC Adapter ...........2-4
Proper handling of the Battery Pack ..............2-4
Turning on the Computer .........................................2-5
LED Indicators .........................................................2-6
LED Status Indicators .........................................2-7
LED Power & Communication Indicators ......... 2-8
The Hard Disk Drive (HDD) ....................................2-9
The External IDE Device .......................................2-10
The Floppy Disk Drive (FDD) ...............................2-11
Inserting/Removing Floppy Disks .................... 2-11
The CD Device ...................................................... 2-12
Loading Discs .................................................. 2-12
Handling CDs or DVDs ................................... 2-13
DVD Regional Codes ....................................... 2-14
Changing the DVD Regional Codes ............ 2-15
The PC Card Slot ................................................... 2-16
Inserting and Removing PC Cards ................... 2-16
Hot-Keys ................................................................ 2-17
My Computer Hot-Key ................................ 2-17
Programming the Hot-Keys ......................... 2-17
The Function Keys and Numeric Keypad .............. 2-19
Function Keys .............................................. 2-19
The Numeric Keypad ................................... 2-19
Function Keys and Numeric Keypad ........... 2-21
TouchPad and Buttons/Mouse ............................... 2-22
Configuring the TouchPad and Buttons ........... 2-22
Adding a Printer ..................................................... 2-23
USB Printer ...................................................... 2-23
Install Instructions: ...................................... 2-23
Parallel Printer .................................................. 2-24
Install Instructions: ...................................... 2-24
Advanced Controls ......................3-1
Overview .................................................................. 3-1
Advanced Video Controls ........................................ 3-2
XV
Preface
Opening the LCD ................................................3-2
Video Driver Controls ..............................................3-3
Making Adjustments for the Display ..................3-3
Display Properties ..........................................3-4
SiS Utility Tray/Manager ...................................3-5
Video Memory .........................................................3-7
Display Devices and Options ...................................3-8
Switching/Enabling Displays (Keyboard) .......... 3-9
Switching/Enabling Displays (Driver) ............. 3-10
Mirror Mode .................................................3-11
Multimonitor ................................................3-12
Adjusting Monitor Settings ....................................3-14
Power Management Features .................................3-18
Advanced Configuration & Power Interface .... 3-18
Enabling Power Options .........................................3-19
Conserving Power (Individual Components) ... 3-20
Turn off Monitor ..........................................3-20
Turn off Hard Disks .....................................3-20
Conserving Power (System) .............................3-21
Hibernate Mode vs. Shutdown ..................... 3-21
Standby Mode vs. Hibernate Mode .............. 3-21
Standby .........................................................3-22
Hibernate ......................................................3-22
Configuring the Power Button ..........................3-23
Battery Information ................................................3-24
New Battery ................................................. 3-24
Battery Life .................................................. 3-24
Battery FAQ ..................................................... 3-25
Conserving Battery Power ............................... 3-25
Removing and Replacing the Battery .............. 3-26
Installing the CDMA or GPRS SIM Card ............. 3-27
Drivers & Utilities ........................4-1
Overview .................................................................. 4-1
What to Install .......................................................... 4-2
Authorized Driver Message ............................... 4-3
Version Conflict Message .............................. 4-3
Install Procedure ................................................ 4-3
Windows 2000 Professional .................................... 4-4
Audio (Win2000) ............................................... 4-4
Modem (Win2000) ............................................. 4-5
LAN (Win2000) ................................................. 4-6
Video (Win2000) ............................................... 4-6
USB 2.0 (Win2000) ........................................... 4-6
TouchPad (Win2000) ......................................... 4-7
Hot-Key (Win2000) ........................................... 4-7
Windows XP ............................................................ 4-8
Audio (WinXP) .................................................. 4-8
Modem (WinXP) ................................................ 4-9
LAN (WinXP) .................................................. 4-10
XVI
Preface
Video (WinXP) .................................................4-10
TouchPad (WinXP) ..........................................4-11
Hot-Key (WinXP) .............................................4-11
BIOS Utilities ...............................5-1
Overview ..................................................................5-1
Important BIOS Settings ..........................................5-2
The Power-On Self Test (POST) .............................5-3
Failing the POST ................................................5-4
Fatal Errors .....................................................5-4
Non-Fatal Errors .............................................5-4
The Setup Program ...................................................5-5
Entering Setup ....................................................5-5
Setup Screens ......................................................5-6
Main Menu ...............................................................5-7
Advanced Menu .......................................................5-9
Security Menu ........................................................5-13
Boot Menu ..............................................................5-15
Configuring the Network Boot Protocol ..........5-17
Exit Menu ...............................................................5-18
Upgrading The Computer ...........6-1
Overview ..................................................................6-1
When Not to Upgrade .........................................6-2
Upgrading the Hard Disk Drive ...............................6-3
Removing the Hard Disk ....................................6-3
Setting up a New HDD ...................................... 6-4
Upgrading the System Memory ............................... 6-5
Upgrading the Memory in Socket 2 ................... 6-6
Upgrading the Processor .......................................... 6-8
Troubleshooting ...........................7-1
Basic Hints and Tips ................................................ 7-2
Backup and General Maintenance ........................... 7-3
Viruses ..................................................................... 7-4
Upgrading and Adding New Hardware/Software .... 7-5
Power ....................................................................... 7-7
Display ..................................................................... 7-9
Hard Disk & Boot Password .................................. 7-11
Floppy Disk Drive ................................................. 7-12
Audio & CD Device .............................................. 7-13
PC Card .................................................................. 7-15
Keyboard and Mouse ............................................. 7-16
Printer ..................................................................... 7-17
Operation ............................................................... 7-18
Appendix A. Specifications A-1
Overview 1 - 1
1
Introduction
Chapter 1: Introduction
Overview
This manual refers to the hardware and essential software required to run your
notebook computer. Depending on how your system is configured, some or all
of the features described may already be set up. What this chapter covers:
• Quick Start Guide — the minimum you need to know
• System Map — navigating around your computer
Advanced Users
If you are an advanced user you may skip over most of this manual. However
you may find it useful to refer to “Drivers & Utilities” on page 4 - 1,
“BIOS
Utilities” on page 5 - 1 and
“Upgrading The Computer” on page 6 - 1. You
may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers, or do not have an advanced knowledge of them,
try to look through all the documentation. Do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn
as you go. You may find it useful to refer to the notes marked with a
as
indicated in the margin.
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Introduction
1 - 2 Overview
1
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and
handling instructions as indicated in the
Preface.
Not Included
Operating Systems (e.g. Windows 2000 Professional, Windows XP etc.) have
their own manuals, as do applications (e.g. word processing, spreadsheet and
database programs). If you have questions about the operating systems or programs then please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where
this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the following operating systems:
• Microsoft Windows 2000
• Microsoft Windows XP
Quick Start Guide 1 - 3
1
Introduction
Quick Start Guide
This guide assumes that you are already familiar with computers and can tell
at a glance what and where all the key components are. If you are not that comfortable with this type of device, then please refer to the following pages,
which give an overview of the system.
It is still best to review these steps, before taking any action. If there is anything you are not sure about, then please refer to the appropriate chapter before
continuing.
Unless you need to install an operating system your computer should be ready
to work right out of the box. Before you begin to undertake the steps outlined
below please follow the safety instructions in the Preface.
1. Remove all packing materials, CDs/DVDs, floppy disks, and PC Cards.
2. Securely attach any peripherals you want to use with the notebook (e.g.
keyboard and mouse) to their ports.
3. Attach the AC adapter to the DC-in jack on the left of the computer.
4. Plug the AC power cord into an outlet, and then connect the AC power cord
to the AC adapter.
5. Raise the lid/LCD to a comfortable viewing angle.
6. Press the power button to turn “on” the computer.
Peripheral Devices
Please note that peripherals (printers, digital cameras, etc.)
which attach to your
computer by either
USB or IEEE1394
ports may be connected after Windows is up
and running. All other
peripherals must be
connected before you
turn on the system.
Introduction
1 - 4 CDMA or GPRS Modem Operation
1
CDMA or GPRS Modem Operation
If you have purchased the optional internal CDMA OR GPRS modem module, full instructions for use are available in the manual that accompanies the
module.
CDMA
For most CDMA services you will need to install the CDMA Application,
then activate the service for your CDMA modem module (you do not usually
need a SIM card). However some service providers do require you to install a
SIM card for your CDMA RUIM (Removable User Identity Module) service
instead. Check with your service provider for instructions.
GPRS
The internal GPRS modem module is used in conjunction with your SIM card
(supplied by your GPRS service provider or mobile phone service provider).
For instructions on installing the SIM card see “Installing the CDMA or
GPRS SIM Card” on page 3 - 27.
Turning the Modem OFF & ON
The default power state for the internal CDMA or GPRS modem module is set
to OFF. When your computer ‘Boots Up’ the modem will be OFF. Press and
hold the Fn + Z keys to toggle the modem ON/OFF. When the modem is ON,
the LED Communication Indicator will flash green.
Modem Operation
Aboard Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make
sure the modem is
OFF, if you are using
the computer aboard
aircraft.
CDMA or GPRS
Software
The software applications provided with the
optional CDMA or
GPRS module are
compatible with the
Windows XP operating system only.
System Map 1 - 5
1
Introduction
System Map
Your notebook PC has a lot of built-in features. Most of these are enabled by
your operating system. Further explanations of the various subsystems are
covered in the chapter or pages indicated.
Getting to Know Your Computer
The following pages will help you to become familiar with the basic functions,
and to learn the location of the various ports and components of your computer.
Introduction
1 - 6 System Map
1
Top View
To open the LCD panel:
1. Place the computer on a stable surface.
2. Move the cover latch to the right to release the top cover.
3. Lift the top cover to reveal the LCD panel and keyboard.
4. Adjust the LCD panel to a comfortable viewing angle.
5. If you have the optional CDMA/GPRS modem module, you can extend the
phone antenna to use this function to access the internet etc.
Figure 1 - 1
Top View with LCD
Panel Closed
1
2
1
2
System Map 1 - 7
1
Introduction
Front View
Figure 1 - 2
Front View
1. LCD Panel
2. LED Status
Indicators
3. Close Cover Switch
4. Power Button
5. Built-In Microphone
6. Keyboard
7. Speakers
8. Hot-Key Buttons
9. TouchPad &
Buttons
10. LED Power &
Communication
Indicators
11. S/PDIF,
Microphone &
Headphone Jacks
12. Infrared
Transceiver
13. Built-In Telecom
Microphone
1
2
4
3
5
7
6
7
8
9
11
10
12
11
13
Introduction
1 - 8 System Map
1
LCD Panel
See “LCD” on page A - 1 for details on the LCD options for this computer.
LED Status Indicators
Refer to “LED Status Indicators” on page 2 - 7 for more information.
Close Cover Switch
This switch acts as a sensor to tell when the LCD panel is closed. When this
LCD cover sensor is activated, the default setting of your operating system’s
power scheme sends the computer into a power saving state (see
Figure 3 -
16 on page 3-23).
System Map 1 - 9
1
Introduction
Power Button
Press this button to turn your computer On or Off (see “Turning on the Com-
puter” on page 2 - 5).
This button may be configured to be used as a sleep/
resume key in the power management control panel of your operating system
(see
“Configuring the Power Button” on page 3 - 23).
Built-In Microphone
Record on your notebook computer with the built-in microphone.
Keyboard
The computer has a “WinKEY” keyboard with an embedded numeric keypad.
It has the same features as a full-sized desktop keyboard and can easily be replaced with a different language keyboard should you desire.
Forced Off & Shutdown
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press
the power button for 4 seconds to force the system to turn itself off.
Please note that you should always shut your computer down by choosing the Shut
Down/Turn Off Computer command from the Start menu in Windows. This will
help prevent hard disk or system problems.
Introduction
1 - 10 System Map
1
Speakers
Two built-in speakers provide rich, stereo sound.
Hot-Keys
To learn how to set the hot-keys see “Programming the Hot-Keys” on
page 2 - 17.
TouchPad & Buttons
The pointing device features a sensitive glide pad for precise movements, and
functions in the same way as a two-button mouse (see
“TouchPad and But-
tons/Mouse” on page 2 - 22).
LED Power & Communication Indicators
See “LED Power & Communication Indicators” on page 2 - 8.
SPDIF Out Port
You can use this port for S/PDIF (Sony/Philips Digital Interface Format) output, which allows you to connect your DVD-capable PC to a Dolby AC-3
compatible receiver for “5.1” or ‘dts’ surround sound.
System Map 1 - 11
1
Introduction
Microphone-In Jack
Plug an external microphone in to this port to record on your notebook computer.
Headphone-In Jack
Headphones or speakers may be connected through this jack.
Note: Set your system’s volume to a reduced level before connecting to this
jack.
Infrared Transceiver
This transceiver allows wireless communication with an infrared-compatible
device. The infrared transceiver is IrDA 1.1 FIR/SIR/ASKIR compliant. For
further information, please refer to the manual of the device you wish to connect to.
Built-In Telecom Microphone
You can either use the supplied telephone headset microphone, OR speak into
the microphone located under the TouchPad & Buttons, if you have the optional CDMA or GPRS modem module.
Infrared
Communication
The infrared transceiver operates on a “Line
of Sight”.
Make sure nothing is
blocking the “Line of
Sight” between your
system’s transceiver
and the destination’s
transceiver.
Introduction
1 - 12 System Map
1
Left Side View
1
2
3
4
5
6
7
8
9
Figure 1 - 3
Left Side View
1. Antenna (raised)
2. External Monitor
(CRT) Port
3. DC-In Jack
4. PS/2 Type Port
5. Telephone
Headset Jack
6. External IDE
Device Port
7. Mini IEEE 1394
Port
8. PC Card Slot
9. External IDE
Device
System Map 1 - 13
1
Introduction
Antenna
Raise the antenna when using the optional CDMA or GPRS modem.
External Monitor Port
Connect an external monitor to this port to allow dual video or simultaneous
display on the LCD and the external monitor (see
“Multimonitor” on page 3
- 12).
DC-In Jack
Plug the supplied AC adapter into this jack to power your notebook.
PS/2 Type Port
Connect an external PS/2 type mouse or keyboard to this port.
Telephone Headset Jack
Plug the supplied telephone headset into this port if you have the optional
CDMA or GPRS module.
External IDE Port
Plug the external IDE device into this port (see “The External IDE Device”
on page 2 - 10).
Loading...