Eurocom D900K User Manual

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Infor­mation contained herein is for reference only and does not constitute a commitment on the part of the man­ufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©November 2005

Trademarks

This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Cor­poration. Reverse engineering or disassembly is prohibited.

AMD Athlon

is a trademark of SRS Labs, Inc.

WOW technology is incorporated under license from SRS Labs, Inc.

™ is a trademark of Advanced Micro Devices, Inc

I

Preface

FCC Statement

(Federal Communications Commission)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifica­tions not expressly approved by the manufacturer for compliance with the above standards could void your au­thority to operate the equipment.

II

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and
injury to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and b atteries indicated in this manual. Do not d ispose of batterie s in a fire. They
may explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 11A minimum).

CAUTION

Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equip­ment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,

TELECOMMUNICATION LINE CORD

This Computer’s Optical Device is a Laser Class I Product

III

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the component s could be dam­aged.

Do not expose the computer
to any shock or vibration.

Do not place it on an unstable
surface.

Do not place anything heavy
on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating
element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be
badly damaged.

Do not expose it to excessive
heat or direct sunlight.

Do not leave it in a place
where foreign matter or mois­ture may affect the system.

Don’t use or store the com­puter in a humid environment.

Do not place the computer on
any surface that will block the
vents.

IV

Preface

3. A void interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper working pro ced ures for the comp ute r. Shut the co mpute r down p roper ly and don ’t
forget to save your work. Remember to periodically save your data as data may be lost if the battery is
depleted.

Do not turn off the power
until you properly shut down
all programs.

Do not turn off any peripheral
devices when the computer is
on.

5. Take care when using peripheral devices.

Use only approved brands of
peripherals.

Do not disassemble the com­puter by yourself.

Unplug the power cord befor e
attaching peripheral devices.

Perform routine maintenance
on your computer.

V

Preface

Power Safety

The computer has specific power requirements:

Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon­nected all peripherals
and cables (including
telephone lines). It is
advisable to also re­move your battery in
order to prevent acci­dentally turning the
machine on.

VI



• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifi­cations, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If yo u do not
have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head,
not by its wire.

• Make sure the socket and any extension cord(s) you use can support the total cur­rent load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power
cord if you are wet.

Do not use the power cord if
it is broken.

Do not place heavy objects
on the power cord.

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the com­puter.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any
way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Al ways dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to disp ose of thi s battery into the mu nicip al waste
stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery ac cord i n g to the man u fa ctu re r’ s ins tru cti o ns.

VII

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following con­ditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD pan el breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s)
and screw(s) before turning the computer on.

VIII

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.

However, check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’

adapters and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for

both hardware and software. Make sure your “p apers” are handy.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the vents/fan intakes to be blocked. To pre­vent your computer from overheating make sure nothing blocks the vent/fan intake while the computer is in use.

IX

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshoot­ing, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead com­partment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your bat­tery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.

X

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.

• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Fre­quent and short breaks are better than fewer and longer breaks.

XI

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best po sition.

XII

Contents

Notice ...........................................................................I

FCC Statement .......................................................II

Instructions for Care and Operation .....................IV

Power Safety ........................................................VI

Battery Precautions .............................................VII

Cleaning ............................................................ VIII

Servicing ........................................................... VIII

Travel Considerations ..........................................IX

Quick Start Guide

Overview ..................................................................1-1

Advanced Users .....................................................1-2

Beginners and Not-So-Advanced Users .................1-2

Warning Boxes .......................................................1-2

Not Included ...........................................................1-2

System Software .....................................................1-3

System Startup .......................................................1-4

System Map: Top View with LCD Panel Open .......1-5

LED Indicators .......................................................1-6

AP-Key Buttons ............................................... ......1-7

Function Keys & Numeric Keypad ........................1-7

System Map: Front & Rear Views ...........................1-9

System Map: Left View .........................................1-10

Preface

System Map: Right View ....................................... 1-11

System Map: Bottom View ....................................1-12

Windows XP Start Menu & Control Panel ............ 1-13

Video Features .......................................................1-14

Display Devices & Options ................................ 1-14

Power Management Features ................................. 1-16

Storage Devices, Mouse, Audio &
Printer

Overview ..................................................................2-1

Hard Disk Drive ....................................................... 2-2

Optical Device .........................................................2-3

Loading Discs ........................................................ 2-3

Handling CDs or DVDs ......................................... 2-4

DVD Regional Codes ............................................ 2-5

10-in-1 Card Reader ................................................. 2-6

PC Card Slot ............................................................2-7

Inserting and Removing PC Cards ........................ 2-7

TouchPad and Buttons/Mouse ................................. 2-8

Configuring the Infrared Settings for FIR ............... 2-9

Audio Features .......................................................2-10

8 Channel Sound Support ................................... 2-11

Audio "DJ" CD Player ........................................... 2-12

XIII

Preface

Adding a Printer .....................................................2-14

USB Printer ..........................................................2-14

Install Instructions: ..............................................2-14

Parallel Printer ......................................................2-14

Power Management

Overview ..................................................................3-1

Advanced Configuration and Power Interface .......3-1

The Power Sources ......................................... .... .... ..3-2

AC/DC Adapter ......................................................3-2

Battery ....................................................................3-2

Turning on the Computer .........................................3-3

Power Schemes ........................................................3-4

System Power Options .............................................3-6

Hibernate Mode vs. Shutdown ...............................3-6

Stand by Mode vs. Hibernate Mode ....................... 3-6

Stand by .................................................................3-7

Hibernate ............................................................... 3-7

Configuring the Power Button .................................3-8

Battery Information ..................................................3-9

New Battery ..........................................................3-9

Battery Life ...........................................................3-9

Recharging the Battery with the AC/DC Adapter 3-10

Proper handling of the Battery Pack ...................3-11

Battery FAQ .........................................................3-12

Drivers & Utilities

System Software Installation with RAID Option .. 4-1

What to Install ..........................................................4-2

Module Driver Installation .................................... 4-2

Service Packs .........................................................4-4

Authorized Driver Message ................................... 4-5

Version Conflict Message ..................................... 4-5

Updating/Reinstalling Individual Drivers ............. 4-5

Driver Installation .................................................... 4-6

Manual Driver Installation ................................... 4-7

Windows XP ............................................................ 4-8

Driver Installation Procedure .................................4-8

New Hardware Found ............................................ 4-8

Chipset .................................................................. 4-9

RAID .................................................................... 4-9

AMD Processor ..................................................4-10

Video (VGA) ......................................................4-10

Audio .................................................................. 4-10

Modem ................................................................ 4-11

LAN .................................................................... 4-11

AP-Key Buttons ..................................................4-12

TouchPad ............................................................ 4-12

Module Drivers ....................................................4-13

Wireless LAN ..................................................... 4-13

XIV

Preface

WLAN & Bluetooth Combo ...............................4-13

TV Tuner .............................................................4-13

PC Camera ..........................................................4-13

BIOS Utilities

Overview ..................................................................5-1

The Power-On Self Test (POST) .............................5-2

Failing the POST ....................................................5-3

Fatal Errors ............................................................5-3

Non-Fatal Errors ...................................................5-3

The Setup Program ...................................................5-4

Entering Setup ........................................................5-4

Setup Screens .........................................................5-5

Main Menu ...............................................................5-6

System Time & Date (Main Menu) ..........................5-6

IDE Channel 0/1/2/3 Master/Slave (Main Menu) ....5-7

System/Extended Memory: (Main Menu) ................5-7

Advanced Menu .......................................................5-8

Advanced Chipset Control (Advanced Menu) .........5-8

I/O Device Configuration (Advanced Menu) .........5-10

Reset Configuration Data (Advanced Menu) .........5-11

Boot Diagnostic Screen: (Advanced Menu) ...........5-11

Power On Boot Beep (Advanced Menu) ................5-11

Security Menu ........................................................5-12

Set Supervisor Password (Security Menu) .............5-12

Password on boot: (Security Menu) .......................5-13

Boot Menu .............................................................5-14

Exit Menu .............................................................. 5-15

Upgrading The Computer

Overview ..................................................................6-1

When Not to Upgrade ............................................ 6-2

Removing the Battery .............................................. 6-3

Upgrading the Hard Disk Drive(s) ...........................6-4

Upgrading the System Memory (RAM) .................. 6-6

Upgrading the Optical (CD/DVD) Device(s) .......... 6-8

Modules

Overview ..................................................................7-1

The Wireless LAN & Bluetooth Modules ............... 7-2

Mini-PCI Wireless LAN Module ............................ 7-3

Intel WLAN Driver Installation ........................... 7-4

Ralink 6833 WLAN Driver Installation ............... 7-5

Bluetooth/WLAN Combo Module .......................... 7-7

MSI 6855B WLAN Driver Installation ................ 7-8

Bluetooth Module .................................................. 7-11

Bluetooth Driver Installation .............................. 7-11

Mini-PCI TV Tuner Module .................................. 7-13

Installing the AverTV Utility Software .............. 7-14

Installing the Cyberlink PowerDVD 6 Software 7-14

XV

Preface

Digital TV Broadcast Signal ...............................7-15

PC Camera ..............................................................7-16

PC Camera Driver Installation ............................7-16

PC Camera Audio Setup ......................................7-17

EMAMCAP ..........................................................7-19

RAID Setup ............................................................7-21

RAID Mode Setup ................................................7-22

Troubleshooting

Overview ..................................................................8-1

Basic Hints and Tips ................................................8-2

Backup and General Maintenance ............................8-3

Viruses ...................................................................... 8-4

Upgrading and Adding New Hardware/Software ....8-5

Problems & Possible Solutions ................................8-7

Interface (Ports & Jacks)

Overview .................................................................A-1

Ports and Jacks ........................................................A-2

Built-In Microphone ................................................A-2

DC-In Jack .............................................................. .A-2

Serial Port ................................................................A-2

Parallel Port .............................................................A-2

DVI-Out Port ...........................................................A-2

PS/2 Port .................................................................A-2

RJ-11 Phone Jack ....................................................A-3

RJ-45 LAN Jack ......................................................A-3

CATV-In Jack .........................................................A-3

S-Video-In Jack ......................................................A-3

S-Video-Out Jack ....................................................A-3

USB 2.0/1.1 Ports ...................................................A-3

Mini-IEEE 1394a Ports ...........................................A-4

Line-In Jack ............................................................A-4

S/PDIF-Out Jack .....................................................A-4

Microphone-In Jack ................................................A-4

Headphone-Out Jack ...............................................A-4

Security Lock Slot ..................................................A-4

NVIDIA Video Driver Controls

NVIDIA Video Driver Installation ..........................B-1

NVIDIA Display Properties .....................................B-2

Additional Properties ............................................B-3

NVIDIA nView Desktop Manager .......................B-5

Display Devices .......................................................B-6

Attaching Other Displays .........................................B-7

Display Modes .........................................................B-9

Enabling TV Display .............................................B-10

XVI

Specifications

Processor Types .......................................................C-2

Core Logic ...............................................................C-2

LCD ......................................................................... C-2

Security ....................................................................C-2

Memory ................................................................... C-3

BIOS ........................................................................ C-3

Video Card Options .................................................C-3

Storage Options .......................................................C-4

Audio ....................................................................... C-4

Keyboard & Pointing Device ..................................C-4

PCMCIA ..................................................................C-4

I/O Ports ..................................................................C-5

Communication ....................................................... C-5

Card Reader .............................................................C-5

Power Management .................................................C-6

Power .......................................................................C-6

Environmental Spec ................................................C-6

Physical Dimensions & Weight ..............................C-6

Optional ................................................................... C-6

Preface

XVII

Preface

XVIII

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 The Storage Devices (hard disk, optical device, 10-in-1 Card Reader, PC Card), Mouse, Audio
& Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software, or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s TV Tuner, wireless, Bluetooth, camera modules (some of which
may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A A definition of the interface, ports/jacks which allow your computer communicate with external
devices.

• Appendix B Information on the NVIDIA Video driver controls.

• Appendix C The computer’s specification.

1

Overview 1 - 1

1

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”

on page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users



Notes

Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.

If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

Not Included

Operating Systems (e.g. Windows XP etc.) and applications (e.g. word processing, spreadsheet and database pro-
grams) have their own manuals, so please consult the appropriate manuals.

1 - 2 Overview

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the following oper­ating systems:

• Microsoft Windows XP Home & Professional Editions

• Microsoft Windows XP Media Center Edition 2005



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 7. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “What

to Install” on page 4 - 2 for installation instructions.

1

Overview 1 - 3

1

Quick Start Guide

System Startup

2

1

1. LCD Latches

2. LED Power & Communication
Indicators

Figure 1 - 1 - Top Panel with LCD Closed

Please note that you should always shut your computer down by choosing the Shut Down/Turn Off Computer command
from the Start menu in Windows. This will help prevent hard disk or system problems.

1. Remove all packing materials.

2. Place the computer on a stable surface.

3. Securely attach any peripherals you want to use with the
notebook (e.g. keyboard and mouse) to their ports.

4. Attach the AC/DC adapter to the DC-In jack at the rear of the
computer, then plug the AC power cord into an outlet, and connect
the AC power cord to the AC/DC adapter.

5. Move and hold the LCD latches in the direction of the arrows to

1

release the top cover.

6. Raise the lid/LCD to a comfortable viewing angle, and press the
power button to turn the computer “on”.

7. Adjust the LCD panel to a comfortable viewing angle.

8. The LED indicators show the power and battery status of the
computer.

2

1



Shutdown

1 - 4 Overview

System Map: Top View with LCD Panel Open

Quick Start Guide

1



Wireless Device

Operation Aboard

Aircraft

The use of any portable
electronic transmission
devices aboard aircraft
is usually prohibited.
Make sure the mod­ule(s) are OFF if you are
using the computer
aboard aircraft.

The key combination Fn
+ F11 toggles power to
the WLAN modul e, Fn +
F12 to the Bluetooth
module.

1

2

6

3

5

8

7

4

10

11

4 4

Figure 1 - 2 - Top View with LCD Panel Open

1. Optional Built-In PC
Camera

2. LCD

3. LED Power &
Communication
Indicators

4. Speakers

5. LED Status Indicators

6. Built-In Microphone

7. AP-Key Buttons

8. Power Button

9. Lid Sensor (not visible

9

4

externally - see page 3 -

8)

10. Keyboard

11. TouchPad and Buttons

7

8

System Map: Top View with LCD Panel Open 1 - 5

1

Quick Start Guide

LED Indicators

The two sets of LED indicators (LED Status Indica­tors and LED Power & Communication Indicators)

on the computer display helpful information about the
current status of the computer.

Table 1 - 1 - LED Status Indicators

Icon Color Description

Green Card Reader Activity

Green Hard Disk Activity

Green Number Lock Activated

Green Caps Lock Activated

Green

Scroll Lock Activated (to activate

press Fn & Scr Lk)

Table 1 - 2 - LED Power & Communication Indicators

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green

Orange The Battery is Charging

Green The Battery is Fully Charged

Blinking Orange

Green

Orange

The Computer is in Stand by

Mode

The Battery Has Reached

Critically Low Power Status

The (optional) Wireless LAN

Module is powered On

The (optional) Bluetooth

Module is powered On

1 - 6 System Map: Top View with LCD Panel Open

Quick Start Guide

1

AP-Key Buttons

These buttons access the internet, e-mail or a user-de­fined application with one quick button press. Make
sure you install the driver to enable the AP-Key Button
functions (refer to “What to Install” on page 4 - 2).

Table 1 - 3 - AP-Key Buttons

AP-Key Function

Activate the Default E-mail Program

Activate the Default Internet Browser

Activate a User Specified Application

(Default is Windows Media Player)

The AP-Key driver icon will appear in the taskbar
after the driver is installed. Right-Click the icon and
browse to Setup > Application 1, and an open dialog
box will appear. Select an application (e.g. Microsoft
Word) to open when you press the Application AP­Key Button (make sure you select the .exe file, and not
a shortcut to it).

Function Keys & Numeric Keypad

The keyboard has an embedded numerical keypad for
easy numeric data input (see Figure 1 - 3).

Activate the Number Lock feature by pressing the
Num Lk key at the top right of the keyboard. You may
check if Number Lock is enabled or not by looking at
the LED status indicators.



Other Keyboards

If your keyboard is damaged or you just want to make
a change, you can use any standard USB keyboard.
The system will detect and enable it automatically.
However special functions/AP-Key buttons unique to
the system’s regular keyboard may not work.

System Map: Top View with LCD Panel Open 1 - 7

1

Quick Start Guide

Table 1 - 4 - Function Keys

Keys Description

Fn Function Key
Fn + F3 Mute Toggle
Fn + F4 Sleep Toggle
Fn + F5 Decrease Audio Volume
Fn + F6 Increase Audio Volume
Fn + F7 Display Toggle
Fn + F8 Decrease LCD Brightness
Fn + F9 Increase LCD Brightness

Fn + F11 WLAN Module Toggle
Fn + F12 Bluetooth Module Toggle
Fn + Scr

Lk

Scroll Lock Toggle

Figure 1 - 3 - Keyboard

Function Keys

Num Lk & Scr Lk Keys

Numeric Keypad

Fn Key



Special Characters

Some software applications allow the number-keys to be used with Alt to
produce special characters. These special characters can only be produced
by using the numeric keypad. Regular number keys (in the upper row of the
keyboard) will not work. Make sure that Num Lk is on.

1 - 8 System Map: Top View with LCD Panel Open

System Map: Front & Rear Views

1

4 4

3

2

2



Audio "DJ" Player

The built-in standalone audio CD player gives you direct hardware control for audio CDs (MP3
compatible) when the computer is shut down, but has a working power source.

5

5

7 8 96



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)
while the computer is in use.

1

11 12 13

10

14

Quick Start Guide

Figure 1 - 4

Front & Rear Views

1. LCD Latches

2. Audio "DJ" Player
Controls

3. Consumer Infrare d
Transceiver

4. Speakers

5. Vent/Fan Intake

6. DC-In Jack

7. Serial Port

8. Parallel Port

9. DVI-Out Port

10. PS2 Port

11. RJ-11 Phone Jack

12. RJ-45 LAN Jack

13. CATV Jack

14. S-Video-In Jack*

*

*

*Enabled with Optional

Mini-PCI TV Tuner Only

1

System Map: Front & Rear Views 1 - 9

1

Quick Start Guide

System Map: Left View

Figure 1 - 5

Left View

1. S-Video-Out Jack

2. 4 * USB 2.0 Ports

3. 2 * Mini-IEEE 1394a
Port

4. Line-In Jack

5. S/PDIF-Out Jack

6. Microphone-In Jack

7. Head phone-Out Jack

8. 10-in-1 Card Reader

9. PC Card Slot

10. Infrared Transceiver
(see page 2 - 9)



Mini-IEEE 1394a

Both Mini-IEEE 1394a
ports only support SELF
POWERED IEEE 1394a
devices.

9

2

3 31 5

4 6 7

8

10



10-in-1 Card Reader Formats

The card reader allows you to use the most popular digital storage card formats:

• MMC (MultiMedia Card)

• SD (Secure Digital)

• MS (Memory Stick)

• MS (Memory Stick Pro)

• SM (SmartMedia Card)

• CF (Compact Flash)

• IBM Microdrive

• MS Duo (requires PC adapter)

• Mini SD (requires PC adapter)

• RS MMC (requires PC adapter)

Note: If you are installing an operating system (e.g. Windows XP) you will need to disable
the card reader in the BIOS (see “Card Reader: (Advanced Menu > Advanced Chipset

Control)” on page 5 - 10).

1 - 10 System Map: Left View

System Map: Right View

2

1



Changing DVD Regional Codes

Go to the Control Panel and double-click System >
Hardware (tab), click Device Manag er, then click

the + next to DVD/CD-ROM drives. Double-click on
the DVD-ROM device to bring up the Properties di-
alogue box, and select the DVD Region (tab) to
bring up the control panel to allow you to adjust the
regional code (see “DVD Regional Codes” on

page 2 - 5).

Quick Start Guide

Figure 1 - 6 - Right View

1. Primary Optical Device Drive

3

Bay (for CD/DVD Device)

2. Secondary Optical Device
Drive Bay (for CD/DVD
Device)

3. Security Lock Slot



CD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unex­pected power interruption) you may push the end of a straight­ened paper clip into the emergency eject hole. Do not use a
sharpened pencil or similar object that may break and become
lodged in the hole.

1

DVD region detection is device dependent, not OS­dependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.

Media Warning

Don’t try to remove a floppy disk/CD/DVD while the system is
accessing it. This may cause the system to “crash”.

System Map: Right View 1 - 11

1

Quick Start Guide

System Map: Bottom View

Figure 1 - 7 - Bottom View

1. Battery

2. Vent/Fan Intake

3. Memory (RAM) Cover

4. Hard Disk Cover

5. Sub Woofer

6. Video Card Cover

7. CPU Cover



CPU

The CPU is not a user
serviceable part.
Opening this compart­ment, or accessing the
CPU in any way, may
violate your warranty.

7

1

2

2

3

2

5

6

4

2



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instruc­tions.

1 - 12 System Map: Bottom View

Quick Start Guide

Windows XP Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows XP are accessed from the Start menu. When
you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be
placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking
the Start menu and selecting Properties from the menu.

Figure 1 - 8

Start Menu & Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu. The Control Panel allows you to configure the settings for most of the

key features in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic control p anels for
many of the features, however many new control panels are added (or existing ones are enhanced) when you
install the drivers listed in Table 4 - 1, on page 4 - 7. To see all controls it may be necessary to toggle off

gory View

.

Cate-

1

Windows XP Start Menu & Control Panel 1 - 13

1

Quick Start Guide

Video Features

This computer features different PCI Express video card options (see “Video Card Options” on page C - 3).
You can switch display devices, and configure display options, from the Display Properties control panel in

Windows as long as the appropriate video driver is installed. For more detailed video information see“NVIDIA

Video Driver Controls” on page B - 1.

To access Display Properties in Windows:

1. Click Start, point to Settings and click Control Panel (or just click Control Panel).

2. Double-click Display (icon) - In the Appearances and Themes category.

3. Click Settings (tab) in the Display Properties dialog box.

4. Move the slider to the preferred setting in Screen area/resolution (Figure 1 - 9 on page 1 - 15).

5. Click the arrow, and scroll to the preferred setting In Colors/Color quality (Figure 1 - 9 on pag e 1 - 15 ).

6. You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties. Click Settings (tab) and adjust as above.

7. Open the Display Properties control panel, and click Advanced (button) (Figure 1 - 9 on page 1 - 15) to
bring up the Advanced properties tabs.

8. Clicking the tabs or Additional Properties allows you to make any video adjustments you require.

Display Devices & Options

Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or
TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the S-

Video-Out jack.

Video Driver Controls” on page B - 1for details.

See Table 1 - 5, on page 1 - 15 for a summary of the display modes available, and see “NVIDIA

1

2

3

1 - 14 Video Features

Quick Start Guide

1

1

2

3

Figure 1 - 9 - Display Properties Desktop

NVIDIA Display Mode Description

Single One of the connected displays is used as the display device

Clone Both connected displays output the same view

Dualview Both connected displays are treated as separate devices, and act as a virtual desktop

Table 1 - 5 - Display Options

Video Features 1 - 15

1

Quick Start Guide

Power Management Features

The Power Options cont rol panel in Windows (see page 1 - 13) allows you to configure power management
features for your computer. You may conserve power throug h individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10). Pay at-
tention to the instructions on battery care in “Battery Information” on page 3 - 9.

Figure 1 - 10 - Power Options

The computer’s power button, sleep button (Fn + F4 key combination), and Lid Sensor may be set to send
the computer in to either Stand by or Hibernate mode.

Power Saving and Performance

Power Schemes may have an affect on your computer performance (see “Power Schemes” on page 3 - 4).

1 - 16 Power Management Features

Storage Devices, Mouse, Audio & Printer

Chapter 2: Storage Devices, Mouse, Audio & Printer

Overview

Read this chapter to learn more about the following main features and compo­nents of the computer:

• Hard Disk Drive

• Optical Device

• 10-in-1 Card Reader

• PC Card Slot

• TouchPad and Buttons/Mouse

• Configuring the Infrared Settings for FIR

• Audio Features

• Audio "DJ" CD Player

• Adding a Printer

2

Overview 2 - 1

Storage Devices, Mouse, Audio & Printer

2



Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk

Power Safety

Before attempting to
access any of the inter­nal components of
your computer please
ensure that the ma­chine is not connected
to the AC power, and
that the machine is
turned off. Also ensure
that all peripheral ca­bles, including phone
lines, are disconnected
from the computer.

can be taken out to accommodate other 2.5" hard disk drives with a height of

9.5 mm. The hard disk is accessible from the bottom of your computer as

1

seen below. Further details on removing and inserting the hard disk are avail­able in “Upgrading the Hard Disk Drive(s)” on page 6 - 4.

1 2

Figure 2 - 1

Hard Disk Location

Hard Disk

The computer supports both serial (SATA) and parallel (PATA) hard disks.
Make sure you use the appropriate cable for the particular hard disk(s) you

2

use. Only serial (SATA) hard disks support a RAID configuration.

2 - 2 Hard Disk Drive

Storage Devices, Mouse, Audio & Printer

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The ac­tual device will depend on the model you purchased (see “Storage Options”

on page C - 4). The optical device is usually labeled “Drive D:” and may be

used as a boot device if properly set in the BIOS (“Boot Menu” on page 5 -

14).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD
onto the disc tray with label-side facing up (use just enough force for the disc
to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock
“clicks” and you are ready to start. The busy indicator will light up while
data is being accessed, or while an audio/video CD, or DVD, is playing. If
power is unexpectedly interrupted, insert an object such as a straightened pa­per clip into the emergency eject hole to open the tray.

1

2

3

1

2

2

3

1

3



Sound Volume

Adjustment

How high the sound
volume can be set de­pends on the setting of
the volume control
within Windows. Click
the Volume icon on
the taskbar to check
the setting.

Peripherals must be
connected before you
turn on the system.

Figure 2 - 2

Optical Device

2

Optical Device 2 - 3

Storage Devices, Mouse, Audio & Printer

2

If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency
eject hole. However
please do NOT use a
sharpened pencil or
similar object that may
break and become
lodged in the hole.

Disk Eject Warning

Don’t try to remove a
CD/DVD while the sys­tem is accessing it.
This may cause the
system to “crash”.



CD Emergency

Eject

Proper handling of your CDs/DVDs will prevent them from being damaged.
Please follow the advice below to make sure that the data stored on your CDs/
DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Handling CDs or DVDs

2 - 4 Optical Device

Storage Devices, Mouse, Audio & Printer

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on

page 1 - 11.

.

DVD Regional Coding

Regio

n

1 USA, Canada

2

3

4

5

6 China

Geographical Location

Western Europe, Japan, South

Africa, Middle East & Egypt

South-East Asia, Taiwan,

South Korea, The Philippines,

Indonesia, Hong Kong

South & Central America,

Mexico, Australia,

New Zealand

N Korea, Russia, Eastern

Europe, India & Most of Africa

2

Table 2 - 1

DVD Regional Coding

Figure 2 - 3

DVD Regions

Optical Device 2 - 5

Storage Devices, Mouse, Audio & Printer

2

Operating System

If you are installing an
operating system (e.g.
Windows XP), and
have a 10-in-1 Card
Reader present, make
sure to set the Card
Reader option in the
BIOS to “Disabled”.
See “Card Reader:

(Advanced Menu >
Advanced Chipset
Control)” on page 5 -

10.



Installation

Warning

Figure 2 - 4

Removable Disks

10-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push
the card into the slot and it will appear as a removable device.

• MMC (MultiMedia Card)

• SD (Secure Digital)

• MS (Memory Stick)

• MS (Memory Stick Pro)

• SM (SmartMedia Card)

*Note: The PC adapters are usually supplied with these cards.

• CF (Compact Flash Types I & II)

• MD (IBM Microdrive)

• MS Duo (requires PC adapter*)

• Mini SD (requires PC adapter*)

• RS MMC (requires PC adapter*)



Card Reader Cover

Make sure you keep the
cover in the card reader
when not is use. This will
help prevent foreign objects
and/or dust getting in to the
card reader.

The cards will appear as removable disks on the computer and can be accessed
in the same way as your hard disk(s).

2 - 6 10-in-1 Card Reader

Storage Devices, Mouse, Audio & Printer

PC Card Slot

The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC
Card.

Inserting and Removing PC Cards

• Align the PC Card with the slot and push it in until it locks into place.

• To remove a PC Card, simply press the eject button next to the slot.

1

1

2

Figure 2 - 5

PC Card Slot

PC Card Slot 2 - 7

Storage Devices, Mouse, Audio & Printer

2



TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a

Mouse Driver

If you are using an ex­ternal mouse your op­erating system may be
able to auto-configure
your mouse during its
installation or only en­able its basic functions.
Be sure to check the
device’s user docu­mentation for details.

mouse to your computer through one of the USB p orts. The TouchPad buttons
function in much the same way as a two-button mouse. The central button may
be configured to function as you require.

Once you have installed the TouchPad driver (see page 4 - 12) you can con­figure the functions by double-clicking the TouchPad driver icon on the
taskbar. You may then configure the TouchPad tapping, buttons, scrolling,
pointer motion and sensitivity options to your preferences. You will find fur­ther information on this at www.synaptics.com.

Figure 2 - 6

Mouse Properties

2 - 8 TouchPad and Buttons/Mouse

Storage Devices, Mouse, Audio & Printer

Configuring the Infrared Settings for FIR

To configure your computer for Fast Infrared (FIR) communication follow
these steps:

1. Click Start, point to Settings and click Control Panel (or just click Start >
Control Panel).

2. Double-click Wireless Link (Printers and Other Hardware Category) icon.

3. Click Hardware (tab), and click the Properties button, then click the
Advanced (tab).

4. Select “Infrared Transceiver A” and change the Value to “HP HSDL-
2300/3600”.

5. Click OK > OK.

6. Restart the computer if prompted to do so.

You can change the infrared transceiver mode (serial port B) from the BIOS
settings (see “I/O Device Configuration (Advanced Menu)” on page 5 - 10).
For further information, please refer to the manual of the device you wish to
connect.



Infrared

Communication

The infrared transceiv­er operates on a “Line
of Sight”.

Make sure nothing is
blocking the “Line of
Sight” between your
system’s transceiver
and the destination’s
transceiver.

2

Configuring the Infrared Settings for FIR 2 - 9

Storage Devices, Mouse, Audio & Printer

2



Sound Volume

Adjustment

Audio Features

You can configure the audio options on your computer from the Sounds and
Audio Devices Windows control panel (see Figure 1 - 8 on page 1 - 13),
or from the Sound Effect Manager icon in the taskbar/control panel (this

How high the sound
volume can be set de­pends on the setting of
the volume control
within Windows. Click
the Volume icon on the
taskbar to check the
setting.

will bring up the Realtek Audio Configuration menus). The volume may also
be adjusted by means of the Fn + F5/F6 key combination.

Figure 2 - 7

Realtek Audio

Configuration

Menus

2 - 10 Audio Features

Storage Devices, Mouse, Audio & Printer

8 Channel Sound Support

If you wish to configure your system for 8 channel sound sup port, then the fol­lowing ports should be used as outputs.

• Side Speaker Out - Connect to S/PDIF Out

• Center/Subwoofer Speaker Out - Connect to Microphone In

• Front Speaker Out - Connect to Speaker/Headphone Out

• Rear Speaker Out - Connect to Line In

2

Figure 2 - 8

8 Channel Sound

Support

Audio Features 2 - 11

Storage Devices, Mouse, Audio & Printer

2



Audio "DJ" CD Player

The built-in standalone audio CD player gives you direct hardware control for

Disk Eject Warning

Don’t try to eject a CD/
DVD while the system
is accessing it. This
may cause the system
to “crash”. Stop the
disk first then eject it,
or press the stop but­ton twice.

audio CDs/DVDs when the computer is shut down, but has a working power
source.

1. Make sure that the computer is shut down (i.e. the oper ating system is not
running) but you have a working power source (either battery or AC Power).

2. Press the Audio "DJ" power button.

3. Press the open button on your CD/DVD device (o r press the stop button
twice) and carefully place an audio CD onto the disc tray with label-side
facing up (DVD drives will also play audio CDs).

4. Gently push the CD/DVD tray in until its lock “clicks” and you are ready to
start.

5. The Audio Format Indicator will flash while data is being accessed and will
then display the audio format of the CD/DVD (CD or MP3).

6. The LED will display the number of tracks.

7. Click the play/pause button to start the CD/DVD.

8. You can control the CD/DVD tracking and volume from the control panel.

9. Use the stop button to stop the disc, or press it twice to eject the disk.

10. The player can be turned off by pressing the power button again.

7

2 - 12 Audio "DJ" CD Player

Storage Devices, Mouse, Audio & Printer



101112

2

1

4

3

6

7

9

8

5

1. Audio "DJ" Power Button

2. Previous Track

3. Next Track

4. Shuffle (loop, in order, shuffle)

5. LED Display

6. Play/Pause

7. Stop (press twice to eject the CD/DVD)

8. Volume Down

9. Volume Up

10. Audio Format Indicator

11. Shuffle Mode Indicator

12. Track Indicator

Note: The time will be displayed on the LED Display if set in the
BIOS (see “Display Time on LED (Advanced Menu > Ad-

vanced Chipset Control)” on page 5 - 10 ).

TV Tuner Option

If you have included
the optional TV Tuner
in your purchase con­figuration, you can use
the supplied remote
control unit to control
the Audio "DJ".

Figure 2 - 9

Audio "DJ"

Controls

2

Audio "DJ" CD Player 2 - 13

Storage Devices, Mouse, Audio & Printer

2

After setting up the
printer attach the paral­lel cable to the printer.

Connect the printer’s
parallel cable to the
Parallel port.

Turn ON the printer,
then the computer.

Windows will identify
the printer and either
load one of its own
drivers or ask you to
supply one. Follow the
on-screen instructions.



Parallel Printer

Adding a Printer

The most commonly used peripheral is a printer. The following conventions
will help you to add a printer, however it is always best to refer to the printer
manual for specific instructions and configuration options.

USB Printer

Most new printers have a USB interface connection. You may use any one of
the ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (unpacking, paper tray, toner/
ink cartridge etc.).

2. Turn ON the computer.

3. Turn ON the printer.

4. Connect the printer’s USB cable to one of the USB ports on the computer.

5. Windows will identify the printer and either load one of its own drivers or
ask you to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the
sidebar.

2 - 14 Adding a Printer

Power Management

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer uses the
ACPI power management system. Power management conserves power by
controlling individual components of the computer (the monitor and hard disk
drive) or the whole system.

This chapter covers:

• The Power Sources

• T urning on the Computer

•Power Schemes

• System Power Options

• Configuring the Power Button

• Battery Information

Advanced Configuration and Power Interface

The ACPI interface provides the computer with enhanced power saving tech­niques and gives the operating system (OS) direct control over the power and
thermal states of devices and processors. For example, it enables the OS to set
devices into low-power states based on user settings and information from ap­plications. ACPI is fully supported in Windows XP.



OS Note

Power management
functions will vary
slightly depending on
your operating system.
For more information it
is best to refer to the
user’s manual of your
operating system.

(Note: All pictures
used on the following
pages are from the
Windows XP OS.)

3

Overview 3 - 1

Power Management



3

Power Button as

Stand by or

Hibernate Button

If you are using a fully
ACPI-compliant OS,
(such as Windows XP)
you can use the OS’s
“Power Options” con­trol panel to set the
power button to send
the system into Stand
by or Hibernate mode
(see your OS’s docu­mentation, or “Config-

uring the Power
Button” on page 3 - 8

for details).

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type
of AC/DC adapter will damage the computer and its components (see page C

- 6).

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC po we r cord in to an o utlet, an d then conn ect the AC power cor d
to the AC/DC adapter.

3. Raise the lid/LCD to a comfortabl e viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or
when an electrical outlet is unavailable. Battery life varies depending on the
applications and the configuration you're using. To increase battery life, let

the battery discharge completely before recharging (see “How do I com-

pletely discharge the battery?” on page 3 - 12).

We recommend that you do not remove the battery. For more information on
the battery, please refer to “Battery Information” on page 3 - 9.

The Power Sources

3 - 2 The Power Sources

Power Management

Turning on the Computer

Now you are ready to begin using your computer. To turn it on simply press
the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hiber­nate/Shutdown hot-key button when it is pressed for less than 4 seconds
(pressing and holding the power button for longer than this will shut the com­puter down). Use Power Options in the Windows control panel to configure
this feature.



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press
the power button for 4 seconds, or longer, to force the system to turn itself off.



Shutdown

Note that you should
always shut your com­puter down by choos­ing the Shut Down/

Turn Off Computer

command from the

Start menu in Win­dows. This will help

prevent hard disk or
system problems.

3

Turning on the Computer 3 - 3

Power Management



3

Resuming
Operation

Press a key on the
keyboard to have the
system resume from
Monitor or Hard Disk
Stand by.

Figure 3 - 1

Power Schemes

You can set your computer to conserve power through individual components
by means of Power Schemes. You can also adjust the settings for each
scheme to set the monitor to turn off after a specified time, and the computer's
hard disk motor to turn off if the hard disk drive has not been accessed for a
specified period of time (if the system reads or writes data, the hard disk motor
will be turned back on). The schemes may also be set to set a specified time
for the system to enter Stand by or Hibernate modes (see “System Power

Options” on page 3 - 6).

Power Schemes

3-4Power Schemes

Each Windows Power Scheme will also adjust the processor performance of
your machine in order to save power. This is worth bearing in mind if yo u are
experiencing any reduced performance (especially under DC/battery power).

Choose the Home/Office Desk scheme for maximum performance when the
computer is powered from an AC power source. Choose the Max Battery
scheme (bear in mind that this scheme may slow down the overall perfor­mance of the computer in order to save power) for maximum power saving
when the computer is battery (DC power) powered.

Windows will use Portable/Laptop as the default scheme.

Power Management

3

Power Schemes 3 - 5

Power Management

System Power Options

You can use the system power options to stop the computer’s operation and

3

restart where you left off. This system features Stand by and Hibernate sleep
mode levels (Hibernate mode will need to be enabled by clicking the option
in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on

page 3 - 7).

Hibernate Mode vs. Shutdown

Hibernate mode and Shutdown are the same in that the system is off and you
need to press the power button to turn it on. Their main difference is:

When you come back from hibernation, you can return to where you last left
off (what was on your desktop) without reopening the application(s) and
file(s) you last used.

You can use either method depending on your needs.

Stand by Mode vs. Hibernate Mode

If you want to stay away from your work for just a while, you can put the sys­tem on Stand by instead of in hibernation. It takes a longer time to wake up
the system from Hibernate mode than from Stand by mode.

3 - 6 System Power Options

Stand by

Stand by saves the least amount of power, but takes the shortest time to return
to full operation. During Stand by the hard disk is turned off, and the CPU is
made to idle at its slowest speed. All open applications are retained in memo­ry. When you are not using your computer for a certain length of time, which
you specify in the operating system, it will enter Stand by mode to save power.

Hibernate

Hibernate uses no power and saves all of your information on a part of the
HDD before it turns the system off. Although it saves the most power it takes
the longest time to return to full operation. You can set your computer to au­tomatically enter Hibernate mode when the battery power is almost depleted.
You will need to enable Hibernate mode from the Hibernate tab in the Power
Options control panel. The system will resume from Hibernate mode by
pressing the power button.

Power Management



System Resume

The system can resume
from Stand by mode by:

• Pressing the power
button

• Pressing a key on the

keyboard

• An alarm resume that

is enabled and
expires

• An incoming call

received on the
modem (if enabled)

• Network card activity

(if enabled)

3

Figure 3 - 2

Enable Hibernation

System Power Options 3 - 7

Power Management

Configuring the Power Button

The power button may be set to send the computer in to either Stand by or

3

Figure 3 - 3

Power Options

(Advanced - Power

Buttons)

Hibernate mode. In Stand by mode, the LED will flash green. In Hi­bernate mode the LED will be off. If you are in a power saving mode set to

save power through individual components (e.g. hard disk, monitor), the LED
will remain green.

Power Button Sleep/ResumeLid

You may also configure the Sleep/Resume key combination (Fn + F4) from the
menu illustrated in Figure 3 - 3. In Windows this is referred to as the Sleep button.

3 - 8 Configuring the Power Button

(Sleep) Button



Sleep Button

Power Management

Battery Information

Please follow these simple guidelines to get the best use out of your battery.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery

FAQ” on page 3 - 12 for instructions on how to do this).

Battery Life

Your computer’s battery life is dependent upon many factors, including the
programs you are running, and peripheral devices attached. Power Options
(you may set low battery Alarms and actions, and check the Power Meter
from the Power Options control panel), and settings in the OS will help pro­long the battery life if configured appropriately.



Low Battery

Warning

When the battery is
critically low, immedi­ately connect the AC/
DC adapter to the
computer or save your
work, otherwise, the
unsaved data will be
lost when the power is
depleted.

Figure 3 - 4

Power Options

(Alarm & Power

Meter)

3

Battery Information 3 - 9

Power Management

Battery life may be shortened through improper maintenance. To optimize



3

Conserving

Battery Power

To conserve battery pow­er:

Lower the brightness lev­el of the LCD display. The
system will decrease LCD
brightness slightly to save
power when it is not pow­ered by the AC/DC adapt­er.

Close modem or commu­nication applications
when they are not being
used.

Remove any unused PC
Cards from the computer
(PC Cards quickly use up
battery power even if the
system enters sleep
mode).

Disconnect any unneces­sary external devices.

the life and improve its performance, fully discharge and recharge the
battery at least once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to
remove the battery for any reason see “Removing the Battery” on page 6 - 3.

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached
and plugged into an electrical outlet. If the computer is powered on, and in use,
it will take several hours to fully recharge the battery. When the computer is
turned off but plugged into an electrical outlet, battery charge time is less. (Re­fer to “LED Indicators” on page 1 - 6 for information on the battery charge
status, and to “Battery Information” on page 3 - 9 for more information on
how to maintain and properly recharge the battery pack.)

3 - 10 Battery Information

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances

• DO NOT expose the battery to fire or high temperatures, it may explode

• DO NOT connect the metal terminals (+, -) to each other



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent out of shape after
being dropped), or any unusual smells emanating from the no tebook batter y, shut
your computer down immediately and contact your service center. If the battery has
been dropped we do not recommend using it any further, as even if the computer
continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire. It is recommended that you replace your computer
battery every two years.

Power Management

3

Battery Information 3 - 11

Power Management

Battery FAQ



3

Caution

Danger of explosion if
battery is incorrectly
replaced.

Replace only with the
same or equivalent
type recommended by
the manufacturer. Dis­card used battery ac­cording to the
manufacturer’s in­structions.

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery.
Don’t turn off the computer by yourself even when you see a message that in­dicates the battery is critically low, just let the computer use up all of the bat­tery power and shut down on its own. Disable the Power Options functions
in the Control Panel, especially any Alarms (unclick the tickboxes - see 3 -

9) and Schemes (change all the settings to Never - see page 3 - 4). As the bat-

tery nears the end of its life save and close any critical files.

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light
changes from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or af­ter about 20 partial discharges.

3 - 12 Battery Information

Chapter 4: Drivers & Utilities

Drivers & Utilities

This chapter deals with installing the drivers and
utilities essential to the operation or improvement
of some of the computer’s subsystems. The system
takes advantage of some newer hardware compo­nents for which the latest versions of most available
operating systems haven’t built in drivers and utili­ties. Thus, some of the system components won’t
be auto-configured with an appropriate driver or
utility during operating system installation. Instead,
you need to manually install some system-required
drivers and utilities.The following operating sys­tem is covered.

• Windows XP Professional and Home Editions

• Windows XP Media Center Edition

System Software Installation with RAID Option

If you have included the RAID option in your pur­chase configuration and want to install a Windows
XP operating system, prepare the following before
beginning to install the OS:

• A USB floppy disk drive

• A Windows XP OS CD/DVD

• A formatted blank 3.5" 1.44MB floppy diskette

•The Device Drivers & Utilities + User’s Man-

ual CD-ROM

See the “RAID Setup” on page 7 - 21 for instruc­tions on creating the RAID and installing the OS.
You can then install the appropriate drivers and
utilities (from page 4 - 9).

4

4-1

Drivers & Utilities

What to Install

The Device Drivers & Utilities + User’s Manual CD-ROM contains the drivers and utilities necessary for
the proper operation of the computer. The drivers for all the modules (WLAN, Bluetooth, PC Camera
and TV Tuner) are on the separate CD-ROMs supplied. Table 4 - 1, on page 4 - 7 lists what you need to

4

install manually according to your choice of the operating system, and it is very important that the driv­ers are installed in the order indicated.

Module Driver Installation

The procedures for installing drivers for the Wireless LAN, Bluetooth, TV Tuner, and PC Camera mod-
ules are provided in “Modules” on page 7 - 1. Make sure that the drivers are installed in the order indicat­ed in Table 4 - 1, on page 4 - 7.

4 - 2 What to Install



Navigate (Browse..) to D:

You will notice that many of the instructions for driver
installation require you to “Navigate (Browse) to D:”.
We assume that you will install all drivers and utilities
from the built-in CD device and it is assigned to “Drive
D:”. In addition, all file extensions can be seen

In this case “D:” is the drive specified for your CD de­vice. Not all computers are setup the same way, and
some computers have the CD listed under a different
drive letter - e.g. if you have two hard drives (or hard
disk partitions) one may be designated as “Drive C:”
and the other as “Drive D:”. In this case the CD device
may be designated as “Drive E:” - Please make sure
you are actually navigating to the correct drive letter
for the CD device.

When you click the Browse (button) after clicking
Run in the Start menu you will see the “Look in:” di­alog box at the top of the Browse window. Click the
scroll button to navigate to My Comput er to display
the devices and drive letters.

Drivers & Utilities

4

Figure 4 - 1 - Navigate (Browse..) to..

What to Install 4 - 3

Drivers & Utilities

Service Packs

Check the warnings on the following pages regard­ing installation of the appropriate Service Pack for
your Windows OS. If you are unsure of the Service
Pack currently installed see below. Make sure you

4

have installed the appropriate Service Pack before
installing all the drivers.



Service Pack Installed

To see which Service Pack is currently installed on
your computer go to the General tab of the System
control panel. Right-click the My Computer icon on
the desktop or in the Start menu and select Proper-
ties. The Service Pack currently installed on your sys­tem will be listed under the “System:” heading. (If no
Service Pack information is listed, then no Service
Pack is installed.)

Make sure you install Windows XP Service Pack 2
(or a Windows XP version which includes Service
Pack 2) before installing any drivers. Service
Pack 2 includes support for USB 2.0.

If you have upgraded the system by installing Ser-
vice Pack 2 (i.e. your Windows XP version does not
include Service Pack 2) then follow these instruc­tions:

1.Click Start (menu), point to Settings and click

2.Double-click System (icon); System (icon) is in

3.Click the Hardware (tab) > Device Manager (but-

4.Click “+” next to Other Devices (if its sub-items

5.Right-click Universal Seria l Bus (USB) Control-

6.Restart the computer and it will find the USB 2.0

Windows XP Service Pack 2

Control Panel (or click Control Panel).
Performance and Maintenance (category).

ton).
are not shown).
ler and select Uninstall > OK (if you don’t see the

item then there is no need to take any further ac­tion).

controller.



4 - 4 What to Install

Drivers & Utilities

Authorized Driver Message

If you receive a message telling you that the driver
you are installing is not authorized (Digital Signa-

ture Not Found), just click Yes or Continue Any­way to ignore the message and continue the

installation procedure.

You will receive this message in cases where the
driver has been released after the version of Win-
dows you are currently using. All the drivers pro­vided will have already received certification for
Windows.

Version Conflict Message

During driver installation if you encounter any “file
version conflict” message, please click Yes to
choose to keep the existing (newer) version.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To
do this go to the Control Panel in the Windows OS
and double-click the Add/Remove Programs
item. If you see the individual driver listed (if not
see below), uninstall it, following the on screen
prompts (it may be necessary to restart the comput­er). Go to the appropriate section of the manual to
complete the update/reinstall procedure for the
driver in question.

If the driver is not listed in the Add/Remove Pro-
grams item:

1. Click Start (menu), point to Settings and click Con­trol Panel (or click Start > Control Panel).

2. Double-click System (icon); System (icon) is in
Performance and Maintenance (category).

3. Click Hardware (tab) > Device Manager (button).

4. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+”).

5. Look for the Update Driver button (check the Driver
tab) and follow the on screen prompts.

4

What to Install 4 - 5

Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Man­ual CD-ROM and the Notebook Driver Installa­tion application will run automatically. If you want

4

to install the driver manually see “Manual Driver

Installation” on page 4 - 7.

1. Check the driver installation order from Table 4 -

1, on page 4 - 7 (the drivers must be installed

in this order) which is the same as that listed in

the driver installation screen menu.

2. Double-click to select the na me of th e driver yo u
wish to install.

3. Follow the instructions as listed in this chapter.

4. Make a note of the drivers you have installed.

5. If a restart is required af ter installing a driver , you
will usually need to click the “Yes/Finish” button
when prompted to restart the computer.

6. To get back to the Driver Installation screen click
Start (menu) > Run... and navigate (Browse..)
to D:\autodr3p.exe and click OK.
OR
Double-click the My Computer icon, and then
double-click the CD icon.

Figure 4 - 2

Driver Installation Screen

4 - 6 Driver Installation

Drivers & Utilities

Windows XP (SP2) &

Windows XP Media Center Edition (SP2)

Driver Page

Chipset

RAID

AMD Processor

Video (VGA)

Audio

Modem

Network (LAN)

AP-Key Buttons

TouchPad

WLAN Modules

Bluetooth & WLAN Combo

TV Tuner Drivers & Apps

PC Camera

Page 4 - 9

Page 4 - 9
Page 4 - 10
Page 4 - 10

Page 4 - 10
Page 4 - 11

Page 4 - 11
Page 4 - 12

Page 4 - 12

See pages 7 - 4 & 7 - 5

See pages 7 - 8 & 7 - 11

See pages 7 - 14

See page 7 - 16

Manual Driver Installation

If you wish to install the drivers manually, click the

Exit button to quit the Notebook Driver Installa-
tion application, then follow the manual installa-

tion procedure for each driver. The manual
installation procedure begins with instructions on
how to browse to the executable file; “Click Start
(menu) > Run

..”.



Operating System Installation Warning

If you are installing an operating system (e.g. Win­dows XP), and have a 10-in-1 Card Reader present,

make sure to set the Card Reader option in the
BIOS to “Disabled”.

See “Card Reader: (Advanced Menu > Advanced

Chipset Control)” on page 5 - 10.

4

Table 4 - 1 - Driver Installation

Driver Installation 4 - 7

Drivers & Utilities

Windows XP

Driver Installation Procedure

This section covers driver and utility installation in­structions for Windows XP Home & Professional.

4

Insert the Device Drivers & Utilities + User’s Man­ual CD-ROM and click the appropriate driver

name from the NoteBook Driver Installation
menu and follow the instructions to install the driv-

er, or Click Start and navigate (Browse..) to fol­low the manual setup instructions.

Make sure you install Windows XP Service Pack 2
(or a Windows XP version which includes Service
Pack 2) before installing any drivers. Service
Pack 2 includes support for USB 2.0.

If you have upgraded the system by installing Ser-
vice Pack 2 (i.e. your Windows XP version does not
include Service Pack 2) then follow the instructions
in “Windows XP Service Pack 2” on page 4 - 4.

Windows XP Service Pack 2

New Hardware Found

If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the in­stallation procedure (other than when outlined in
the driver install procedure), click Cancel to
close the window, and follow the installation proce­dure.



4 - 8 Windows XP

Drivers & Utilities

Chipset

1. Double-click Chipset.
OR

Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\00CHIPSET\Setup.exe and
click OK.

2. Click Next > Yes > Next > Next.

3. Click OK to restart the computer.

RAID

1. Double-click RAID.
OR

Click S tart (menu) > Run... and navigate
(Browse..) to
D:\Drivers\01RAID\SETUP.EXE and
click OK.

2. Click Next.

3. Click the button to accept the license agree-

ment, then click Next.

4. Click Next > Next > Next.

5. Click Finish to restart the computer.

6. See “RAID Setup” on page 7 - 21 for setup

instructions.

4

Windows XP 4 - 9

Drivers & Utilities

AMD Processor

1. Double-click AMD.
OR
Click Start (menu) > Run... and navigate

4

(Browse..) to
D:\Drivers\02AMD\setup.exe and click
OK.

2. Click Next > Yes > Next > Next.

3. Click the button “Yes, I want to restart the

computer now.”, and click Finish.

Audio

1. Double-click Audio.
OR

Click Start (menu) > Run... and navigate
(Browse..) to

D:\Drivers\04AUDIO\setup.exe and click
OK.

2. Click Next.

3. Click Finish to restart the computer.

Video (VGA)

1. Double-click VGA.
OR

Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\03VGA\NVIDIA\setup.exe
and click OK.

2. Click Next.

3. Click Finish to restart the computer.

4 - 10 Windows XP

Drivers & Utilities

Modem

1. Double-click Modem.
OR

Click Start (menu) > Run... and navigate
(Browse..) to (one of the following)

D:\Drivers\05MODEM\Setup.exe

and click

OK.

2. Click OK > OK.

3. Click Yes to restart the computer.

4. The modem is now ready for configuration.



Modem Country Selection

Be sure to check if the modem country selection is ap­propriate for you (Control Panel > Ph one and Mo-

dem Options).

LAN

1. Double-click Lan.
OR

Click S tart (menu) > Run... and navigate
(Browse..) to

D:\Drivers\06LAN\Setup.exe and click
OK.

2. Click Next.

3. Click Finish.

4. The network settings can now be config-

ured.

4

Windows XP 4 - 11

Drivers & Utilities

AP-Key Buttons

1. Double-click AP-key.
OR
Click Start (menu) > Run... and navigate

4

(Browse..) to
D:\Drivers\07AP-Key\AKSETUP.exe and

click OK.

2. Click Next.

3. Click Finish to restart your computer.

TouchPad

1. Double-click Touchpad.
OR

Click S tart (menu) > Run... and navigate
(Browse...) to
D:\Drivers\08TOUCHPAD\Setup.exe and
click OK.

2. Click Next > Next > Next (click Continue

Anyway if asked if you want to continue at
any time).

3. Click Finish to restart your computer.

4. You may then configure your TouchPad as

outlined in “TouchPad and Buttons/

Mouse” on page 2 - 8.

4 - 12 Windows XP

Drivers & Utilities

Module Drivers

See the following pages for the driver installation
procedures for any modules included in your pur­chase option.

Wireless LAN

See the install procedure in “Intel WLAN Driver

Installation” on page 7 - 4 or “Ralink 6833
WLAN Driver Installation” on page 7 - 5.

WLAN & Bluetooth Combo

See the install procedure in “MSI 6855B WLAN

Driver Installation” on page 7 - 8 and “Bluetooth
Driver Installation” on page 7 - 11.

TV Tuner

See the install procedure in “Installing the AverTV

Utility Software” and “Installing the Cyberlink
PowerDVD 6 Software” on page 7 - 14.

PC Camera

See the install procedure in “PC Camera Driver

Installation” on page 7 - 16.

4

Windows XP 4 - 13

Drivers & Utilities

4

4-14

BIOS Utilities

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are making important ch anges
to the system (e.g. hard disk setup), then you should review this chapter first
and note the original settings found in Setup. Even if you are a beginner, keep
a record of the settings you find and any changes you make. This infor mation
could be useful if your system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what
you are doing. Many of the settings are required by the system, and changing
them could cause it to become unstable or worse. If you have any doubts, con­sult your service representative.



BIOS Settings

Warning

Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to
Setup and restore the
Setup Defaults with
<F9>.

5

Overview 5 - 1

BIOS Utilities

Phoenix cME(tm) TrustedCore(tm) NB
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
BIOS Revision: D900K 1.00.D0AT2
KBC/EC Firmware Revision: 1.00.D5
VGA Card: Nvidia NV42GLM
VBIOS Revision: 5.41.02.39.32-03/10/05

CPU = AMD Athlon(tm) 64 Processor 3000+
623K System RAM Passed
511M Extended RAM Passed
512K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: FUJITSU MHT2040AT
Fixed Disk 1: FUJITSU MHT2040AT
ATAPI CD-ROM: TSSTcorpCDW/DVD TS-L462A
Mouse intialized

Press <F2> to enter SETUP



POST OR Phoenix

Firstware Screen

If you have disabled
the Boot Diagnostic

Screen the POST

5

screen will not appear
(see page 5 - 11), and
the Firstware Screen
will appear instead.

Figure 5 - 1

POST Screen

The Power-On Self Test (POST)

Each time you turn on the computer, the system takes a few seconds to con­duct a POST, including a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong.
If there is a problem that prevents the system from booting, it will display a
system summary and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will
load the operating system. Once that starts, you can’t get into Setup without
rebooting.

1



POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt appears
only during POST

Note: The POST screen as pic­tured is for guideline purposes
only.

3

4

2

5 - 2 The Power-On Self Test (POST)

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and
“non-fatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously
wrong with your system. Take the computer to your service representative or
authorized service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying
the problem (make a note of this message!) followed by the prompt:

• Press <F1> to resume

• <F2> to enter Setup

Press F1 to see if the boot process can continue. It may work, without the cor­rect configuration.

Press F2 to run the Setup program and try to correct the problem. If you still
get an error message after you change the setting, or if the “cure” seems even
worse, call for help.

BIOS Utilities

5

The Power-On Self Test (POST) 5 - 3

BIOS Utilities

The Setup Program

The Phoenix Setup program tells the system how to configure itself and man­age basic features and subsystems (e.g. port configuration).

Entering Setup

To enter Setup, turn on the computer and press F2 during the POST. The

5

prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 on page 5 - 2 is usually
present for a few seconds after you turn on the system. If you get a “Keyboard
Error”, (usually because you pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combina-
tion and then hold down F2 when prompted. The Setup main menu will ap­pear.

5 - 4 The Setup Program

Setup Screens

The following pages contain additional advice on portions of the Setup.

Along the top of the screen is a menu bar with five (5) menu headings. When
you select a heading, a new screen appears. Scroll through the features listed
on each screen to make changes to Setup.

Instructions on how to navigate each screen are in the box along the bottom of
the screen. If these tools are confusing, press F1 to call up a General Help
screen, then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlight­ed item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that
subject. The sub-menu screen that appears has a similar layout, but the Enter
key may execute a command.

BIOS Utilities



Setup Menus

The Setup menus
shown in this section
are for reference only.
Your computer’s men­us will indicate the con­figuration appropriate
for your model and op­tions.

5

The Setup Program 5 - 5

BIOS Utilities

Main Menu

PhoenixBIOS Setup Utility

Figure 5 - 2

Main Menu

5

Main

Main Advanced Security Boot Exit

System Time: [22:11:05]

System Date: [00/22/2005]

IDE Channel 0 Master [FUJITSU MHT2040AT-(PM)]
IDE Channel 0 Slave [FUJITSU MHT2040AT-(PM)]
IDE Channel 1 Master [TSSTcorpCDW/DVD TS-L462A-]
IDE Channel 1 Slave [None]
IDE Channel 2 Master [None]
IDE Channel 3 Slave [None]

System Memory: 624 KB
Extended Memory: 65535 KB

VGA Card: nVIDIA 1400
VBIOS Revision 5.41.02.39.32
VBIOS Build Date

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

10

Item Specific Help

<Tab>, <Shift Tab>, or
<Enter> selects field.

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If
you can change the date and time settings in your operating system, you will
also change these settings. Some applications may also alter data file s to re­flect these changes.

5-6Main Menu

IDE Channel 0/1/2/3 Master/Slave (Main Menu)

Pressing Enter here opens the sub-menu to show the configuration of hard
disks and CD/DVD device(s) on the computer’s IDE Channels. Use the Auto
(Type:) setting to have the items configured automatically for you.

System/Extended Memory: (Main Menu)

This item contain information on the system memory, and is not user config­urable. The system will auto detect the amount of memory installed.

The Main menu also contains information on your video card and video BIOS
version.

BIOS Utilities

5

Main Menu 5 - 7

BIOS Utilities

Advanced Menu

Figure 5 - 3

Advanced Menu

5

Main Advanced Security Power Boot Exit

Setting items on this menu to incorrect
values may cause your system to malfunction.

Advanced Chipset Control

I/O Device Configuration

Reset Configuration Data: [No]
Boot Diagnostic Screen: [Enabled]
Power on Boot Beep [Disabled]

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Advanced

Setup Warning

PhoenixBIOS Setup Utility

Item Specific Help

Advanced Chipset Control (Advanced Menu)

Pressing Enter here will allow you to select options for Advanc ed Chipset
features (see Figure 5 - 4).

5 - 8 Advanced Menu

SATA RAID Enable (Advanced Menu > Advanced Chipset Control)

Enable/Disable SATA RAID mode from this menu (see “RAID Setup” on

page 7 - 21).

PhoenixBIOS Setup Utility

Advanced

Advanced

Advanced Chipset Control

SATA RAID Enable [Enabled]

CPU FAN Speed: [Auto]
Card Reader: [Enabled]
Display Time on LED [Enabled]

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Item Specific Help

Enable SATA RAID
function

CPU FAN Speed (Advanced Menu > Advanced Chipset Control)

Use this menu to adjust the CPU fan speed in order to save power. This item
is set to “Auto” by default.

BIOS Utilities



Operating System

Installation Warning

If you are installing an
operating system (e.g.
Windows XP), and have
a 10-in-1 Card Reader
present, make sure to
set the Card Reader op­tion in the BIOS to “Dis-
abled”.

Figure 5 - 4

Advanced Chipset

Control Menu

5

Advanced Menu 5 - 9

BIOS Utilities

Card Reader: (Advanced Menu > Advanced Chipset Control)

This option allows you to enable/disable support for the 10-in-1 Card Read­er. and is “Enabled” by default. However if you are installing an operating
system (e.g. Windows XP) it is recommended that you disable the card
reader, as otherwise the card reader slots will automatically be defined as
drives “C:” through “F:” (your hard disk drive will then be defined as
drive “G:” etc.). If you set this option to “ Disabled” in order to install the op-

5

erating system, don’t forget to reset the option to “Enabled” after you have
installed the operating system.

Display Time on LED (Advanced Menu > Advanced Chipset Control)

This option allows you to toggle the time display on the Audio "DJ" LED dis­play.

I/O Device Configuration (Advanced Menu)

The sub-menus under this item include options to configure the Serial port A
(Serial Mouse), Serial port B (Infrared) and Parallel (Printer) port. These

can be left to the default settings, however you may wish to use certain devices
that require settings to be adjusted accordingly. Check the documentation for
any such devices to see what settings are required.

5 - 10 Advanced Menu

Reset Configuration Data (Advanced Menu)

This item is set to No as default. You can change the setting to Yes if you have
installed a new add-on which has reconfigured the system, resulting in such a
serious system conflict that the operating system is unable to boot.

Boot Diagnostic Screen: (Advanced Menu)

Use this menu item to enable/disable the Boot-time Diagnostic Screen (or
POST screen - see “The Power-On Self Test (POST)” on page 5 - 2).

Power On Boot Beep (Advanced Menu)

Use this menu to enable/disable the single beep sound at the end of the POST.
This item is “Disabled” by default.

BIOS Utilities

5

Advanced Menu 5 - 11

BIOS Utilities

Security Menu

Figure 5 - 5

Security Menu

5

Main Advanced Security Boot Exit

Supervisor Password Is: Clear

Set Supervisor Password [Enter]

Password on boot: [Disabled]

PhoenixBIOS Setup Utility

Security

Item Specific Help

Supervisor Password
controls access to the
setup utility.



Security Menu

The changes you
make here affect the
access to the Setup
utility itself, and also
access to your ma­chine as it boots up af­ter you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Set Supervisor Password (Security Menu)

You can set a password for access to the Setup utility. This will not affect ac­cess to the computer OS, (only the Setup utility) unless you choose to set a
Password on Boot (see over).

5 - 12 Security Menu

Password on boot: (Security Menu)

Specify whether or not a password (supervisor or user password) should be
entered to boot the computer. If “Enabled” is selected, only users who enter a
correct password can boot the system (see the warning in the sidebar). The
default setting is “Disabled”.

Note: To clear existing passwords press Enter and type the existing password,
then press Enter for the new password (without typing any password entry)
and Enter again to confirm the password clearance.

BIOS Utilities



Password Warning

If you set a boot pass­word (Password on boot
is “Enabled“), NEVER
forget your password.

5

The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your ven­dor and you may lose all
of the information on
your hard disk.

Security Menu 5 - 13

BIOS Utilities

Boot Menu

Figure 5 - 6

Boot Menu

5

Main Advanced Security Exit

Boot priority order:

1: USB FDC:

2: HDD 1: FUJITSU MHT2040AT-(PM)
3: SATA 1:
4: PCI SCSI:
5: CD-ROM 1: TSSTcorpCDW/DVD TS-L462A­6: USB KEY:
7: PCI LAN:
8:

Excluded from boot order:

: HDD 2: FUJITSU MHT2040AT-(PS)
: CD-ROM 2:
: SATA 2:

: USB HDD:

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

PhoenixBIOS Setup Utility

Boot

Item Specific Help

Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves the
device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1 - 4> Loads default
boot sequence.

When you turn the computer on it will look for an operating system (e.g. Win­dowsXP) from the devices listed in this menu, and in this priority order. If it

cannot find the operating system on that device, it will try to load it from the
next device in the order specified in the Boot priority order. Item specific
help on the right is available to help you move devices up and d own the order.

5 - 14 Boot Menu

Exit Menu

BIOS Utilities

PhoenixBIOS Setup Utility

Main Advanced Security Boot Exit

Exit Saving Changes

Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes

F1 Help  Select Item -/+ Change Values F9 Setup Defaults
Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Exit

Item Specific Help

Exit System Setup and
save your changes to
CMOS.

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out
any changes you have made to the Setup. You can also choose to restore the
original Setup defaults that will return the Setup to its original state, and erase
any previous changes you have made in a previous session.

Figure 5 - 7

Exit Menu

5

Exit Menu 5 - 15

BIOS Utilities

5

5-16

Upgrading The Computer

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the
steps outlined to make the desired upgrades. If you have any trouble or prob­lems you can contact your service representative for further help. Before you
begin you will need:

• A small crosshead or Phillips screwdriver

• A small regular slotted (flathead) screwdriver

• An antistatic wrist strap
Before working with the internal components you will need to wear an anti-

static wrist strap to ground yourself because static electricity may damage the
components.

The chapter includes:

• Removing the Battery

• Upgrading the Hard Disk Drive(s)

• Upgrading the System Memory (RAM)

• Upgrading the Optical (CD/DVD) Device(s)



Warranty Warning

Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.

6

Please make sure that you review each procedure before you perform it.

Overview 6 - 1

Upgrading The Computer

When Not to Upgrade



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon-

6

nected all peripherals
and cables (including
telephone lines). It is
advisable to also re­move your battery in
order to prevent acci­dentally turning the
machine on.

These procedures involve opening the system’s case, adding and sometimes
replacing parts.You should not perform any of these upgrades if:

• Your system is still under warranty or a service contract

• You don’t have all the necessary equipment

• You’re not in the correct environment

• You doubt your abilities
Under any of these conditions, contact your service representative to purchase

or replace the component(s).



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, re­member to replace the cover(s) and screw(s) before turning the computer on.

Upgrading the Processor

If you want to upgrade your computer by replacing the existing processor with
a faster/new one you will need to contact your customer service representa­tive. We recommend that you do not do this yourself, since if it is done incor­rectly you may damage the processor or mainboard.

6 - 2 Overview

Upgrading The Computer

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety
reasons it is best to remove the battery.

1. Turn the computer off, and turn it over.

2. Loosen screws

3. Release the battery, and lift the batter y out of the battery bay.

1 3

- .

4

1 2 3

4



Warranty Warning

Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.

6

Figure 6 - 1

Battery Removal

Removing the Battery 6 - 3

Upgrading The Computer



HDD System

Warning

New HDD’s are blank.
Before you begin make
sure:
You have backed up any
data you want to keep
from your old HDD.

6

You have all the CD­ROMs and FDDs re­quired to install your oper­ating system and
programs.
If you have access to the
internet, download the lat­est application and hard­ware driver updates for
the operating system you
plan to install. Copy these
to a removable medium.

Figure 6 - 2

HDD Bay Cover

Removal

The hard disk drive(s) can be taken out to accommodate other 2.5" IDE hard
disk drives with a height of 9.5mm (h) (see “Storage Options” on page C - 4).
Follow your operating system’s installation instructions, and install all neces­sary drivers and utilities (as outlined in “Drivers & Utilities” on page 4 - 1),
when setting up a new hard disk.

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the hard disk bay cover and remove screws

3. Remove the bay cover .

1

5

2

1 4

- .

5

3 4

Upgrading the Hard Disk Drive(s)

6 - 4 Upgrading the Hard Disk Drive(s)

Upgrading The Computer

4. Release the cable and lift the hard disk assembly up out off the

6 7

computer.

5. Remove screws - in order to separate the bracket from the hard
disk(s), and disconnect the cable (see sidebar).

8 15

16

6. Reverse the process to install a new hard disk(s).

15

14

13

12

8

9

7

6

10

11

16



Hard Disk Cable

The computer sup­ports both serial (SA­TA) and parallel
(PATA) hard disks.
Make sure you use the
appropriate cable
for the particular hard
disk(s) you use.

Only serial (SATA)
hard disks (pictured)
support a RAID config­uration.

Figure 6 - 3

HDD Assembly

Removal

16

6

Upgrading the Hard Disk Drive(s) 6 - 5

Upgrading The Computer



Memory Sockets

If you are installing

one memory module

then it must be in­stalled in the lower

memory socket.

6

Figure 6 - 4

RAM Cover

Removal

The computer has two memory sockets for 200 pin Small Outline Dual In-line
(SO-DIMM) DDR type memory modules (see “Memory” on page C - 3). The
total memory size is automatically detected by the POST routine once you
turn on your computer.

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the memory (RAM) bay cover and remove screws
carefully (the fan cable will still be attached) lift off the bay cover .

1 4

- , and

5

5

1

2

3

4

Upgrading the System Memory (RAM)

6 - 6 Upgrading the System Memory (RAM)

Upgrading The Computer

3. Gently pull the two release latches ( & ) on the sides of the me m ory

socket in the direction indicated by the arrows in Figure 6 - 5.

76

4. The RAM module will pop-up, and you can remove it.

5. Pull the latches to release the second module if necessary.

6. Insert a new module holding it at about a 30° angle and fit the connectors
firmly into the memory socket (if you are installing only one RAM module,
then it must be inserted into the lower socket only).

7. The module’s pin alignment will allow it to only fit one way. Make sure the
module is seated as far into the socket as it will go. DO NOT FORCE the
module; it should fit without much pressure.

8. Press the module in a nd down towards the mainboard until the socket levers
click into place to secure the module.

9. Replace the cover and screws (see Figure 6 - 4).

10. Restart the computer to allow the BIOS will register the new memory
configuration as it starts up.

8

6 7

8



Contact Warning

Be careful not to touch
the metal pins on the
module’s connecting
edge. Even the clean­est hands have oils
which can attract parti­cles, and degrade the
module’s perfor­mance.

Figure 6 - 5

RAM Module

Removal

6

Upgrading the System Memory (RAM) 6 - 7

Upgrading The Computer

Upgrading the Optical (CD/DVD) Device(s)

1. Turn off the computer, and turn it over and remove the battery.

2. Locate the hard disk bay cover and remove screws

3. Remove screw

the bay cover.

5

and use the screwdriver to push the optical device(s) out

of the computer at point .

6

1 4

- , and remove

6

Figure 6 - 6

Removing the CD/

DVD Device(s)

6 - 8 Upgrading the Optical (CD/DVD) Device(s)

1

3

5

2

4

6