Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©February 2005
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel® and Pentium® are US registered trademarks of Intel Corporation.
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and
injury to persons when using any electrical equipment:
1. Do not use this product near water , for example near a bath tub, wash bowl, kitch en sink or laundry tub, in
a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not disp ose of batteries in a fir e. They
may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 9A minimum).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Class I Laser Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry , and don’t ov erheat it. Keep the computer and power supply away from any kind of heating
element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be
badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
vents.
IV
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working procedures for the computer. Shut the compu ter d own prop er ly and don ’t
forget to save your work. Remember to periodically save your data as data may be lost if the battery is
depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VI
• Only use a power adapter approved for use with this computer.
• Your AC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If yo u do not
have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head,
not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way.
Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may
possibly result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or
qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to disp ose of thi s battery into the mu nicip al waste
stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery ac cord i n g to the man u fa ctu re r’ s ins tru cti o ns.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD pan el breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s)
and screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’ s latched.
4. Disconnect the AC adapter and cables. Stow them in the carrying bag.
5. The AC adapter uses voltages from 100 to 240 volts so you won’t need a sec on d voltage adapt er.
However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’
adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for
both hardware and software. Make sure your “p apers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the vents/fan intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the vent/fan intake while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and “Troubleshooting” on
page 8 - 1, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best po sition.
XII
Contents
Notice ...........................................................................I
FCC Statement ...................................................II
Instructions for Care and Operation .................IV
Power Safety .....................................................VI
Battery Precautions ..........................................VII
Cleaning ........................................................ VIII
Servicing ........................................................ VIII
Travel Considerations .......................................IX
Quick Start Guide
Overview ..................................................................1-1
Advanced Users .....................................................1-2
Beginners and Not-So-Advanced Users .................1-2
Warning Boxes .......................................................1-2
Not Included ...........................................................1-2
System Software .....................................................1-3
System Startup .......................................................1-4
Getting to Know Your Computer ...........................1-5
1.8" LCD ..................................................................1-6
1.8" LCD Power ON/OFF .....................................1-6
Screen Rotation .....................................................1-6
System Map: Top View with LCD Panel Open .......1-7
LED Indicators .......................................................1-8
Preface
AP-key Buttons .................................................... ..1-9
Function Keys & Numeric Keypad ....................... 1-9
System Map: Front & Rear Views ......................... 1-11
System Map: Left View .........................................1-12
System Map: Right View ....................................... 1-13
System Map: Bottom View ....................................1-14
Windows XP Start Menu & Control Panel ............ 1-15
Video Features ....................................................... 1-16
Video Driver Controls ........................................1-16
Display Devices & Options .................................1-18
Power Management Features ................................. 1-19
Storage Devices, Mail Program,
Mouse, Audio & Printer
Overview ..................................................................2-1
Hard Disk Drive ....................................................... 2-2
Optical Device ......................................................... 2-3
Loading Discs ........................................................ 2-3
Handling CDs or DVDs ......................................... 2-4
DVD Regional Codes ............................................ 2-5
3-in-1 Card Reader ................................................... 2-6
Removing Cards from the Card Reader .......... .... ..2-7
PC Card Slot ............................................................ 2-8
XIII
Preface
Inserting and Removing PC Cards .........................2-8
Auto Mail Checker ...................................................2-9
TouchPad and Buttons/Mouse ...............................2-11
Audio Features .......................................................2-12
Audio "DJ" CD Player ...........................................2-13
Configuring the Infrared Settings for FIR ..............2-15
Adding a Printer .....................................................2-16
USB Printer ..........................................................2-16
Install Instructions: ..............................................2-16
Parallel Printer ......................................................2-16
Power Management
Overview ..................................................................3-1
Advanced Configuration and Power Interface .......3-1
The Power Sources ................................................. ..3-2
AC Adapter ............................................................3-2
Battery ....................................................................3-2
Turning on the Computer .........................................3-3
Power Schemes ................... .....................................3-4
System Power Options .............................................3-6
Hibernate Mode vs. Shutdown ...............................3-6
Standby Mode vs. Hibernate Mode ........................3-6
Standby ..................................................................3-7
Hibernate ............................................................... 3-7
Configuring the Power Button .................................3-8
Battery Information .................................................. 3-9
New Battery .......................................................... 3-9
Battery Life ........................................................... 3-9
Recharging the Battery with the AC Adapter ...... 3-10
Proper Handling of the Battery Pack .................. 3-11
Battery FAQ ........................................................3-12
Drivers & Utilities
What to Install ..........................................................4-1
Module Driver Installation ................................... 4-1
Service Packs .........................................................4-3
Authorized Driver Message ..................................4-4
Version Conflict Message .................................... 4-4
Driver Installation .................................................... 4-5
Manual Driver Installation ................................... 4-6
Windows XP Drivers ............................................... 4-7
New Hardware Found ............................................ 4-7
Chipset (WinXP) .................................................. 4-7
Audio (WinXP) .................................................... 4-8
Modem (WinXP) .................................................. 4-8
LAN (WinXP) ...................................................... 4-9
Video (WinXP) ..................................................... 4-9
AP-Key Buttons (WinXP) .................................. 4-10
TouchPad (WinXP) ............................................ 4-10
PCMCIA & Card Reader (WinXP) .................... 4-11
XIV
Preface
Auto Mail Checker (WinXP) ..............................4-11
LCDAP (WinXP) ................................................4-12
Module Drivers ......................................................4-12
Wireless LAN (WinXP) ......................................4-12
Bluetooth (WinXP) .............................................4-12
TV Tuner (WinXP) .............................................4-12
PC Camera (WinXP) ...........................................4-12
BIOS Utilities
Overview ..................................................................5-1
The Power-On Self Test (POST) .............................5-2
Failing the POST ....................................................5-3
Fatal Errors ............................................................5-3
Non-Fatal Errors ...................................................5-3
The Setup Program ...................................................5-4
Entering Setup ........................................................5-4
Setup Screens .........................................................5-5
Main Menu ...............................................................5-6
System Time & Date ................................................5-6
IDE Channel 0 Master/Slave ...................................5-7
SATA Port 1/2 ..........................................................5-7
Installed memory ......................................................5-7
Advanced Menu .......................................................5-8
System Information ..................................................5-8
I/O Device Configuration .........................................5-9
Reset Configuration Data: ..................................... 5-10
Hyper-Threading Technology ................................5-10
Power On Beep .......................................... .... ........ 5-10
Boot Logo Screen: .................................................5-10
Security Menu ........................................................ 5-11
Set Supervisor Password ........................................ 5-11
Password on boot: ..................................................5-12
Boot Menu .............................................................5-13
Exit Menu ..............................................................5-15
Upgrading The Computer
Overview ..................................................................6-1
When Not to Upgrade ............................................ 6-2
Removing the Primary Battery ................................ 6-3
Upgrading the Hard Disk Drive(s) ...........................6-4
Upgrading the System Memory (RAM) .................. 6-6
Changing the Secondary Bay Device ...................... 6-9
Upgrading the Processor ........................................ 6-10
Modules
Overview ..................................................................7-1
The Mini-PCI WLAN Module Options ................... 7-2
MSI 6855A (802.11b/g) Wireless LAN
Driver Installation ................................................. 7-3
XV
Preface
ZCOM (802.11a/b/g) WLAN Module Driver Installa-
tion ........................................................................7-4
The Bluetooth Module ................................... .... .... ..7-5
Bluetooth Module Driver Installation ................... 7-5
The 7-in-1 Card Reader Module ..............................7-7
The TV Tuner Module ................ ... .... ......................7-8
Installing the AverTV Utility Software ................7-9
Installing the InterVideo WinDVD 4 Software ....7-9
The PC Camera Module Options ...........................7-10
Kenmec PC Camera
Driver Installation (WinXP) ................................7-11
Sertek PC Camera
Driver Installation (WinXP) ................................7-11
PC Camera Audio Setup .....................................7-12
BisonCap ..............................................................7-14
Troubleshooting
Overview ..................................................................8-1
Basic Hints and Tips ................................................8-2
Backup and General Maintenance ............................8-3
Viruses ...................................................................... 8-4
Upgrading and Adding New Hardware/Software ....8-5
Power ........................................................................8-7
Display .....................................................................8-9
Boot Password ........................................................8-10
Audio & CD Device ..............................................8-11
Keyboard ................................................................ 8-12
Operation ............................................................... 8-13
Modules ................................................................. 8-14
Interface (Ports & Jacks)
Overview .................................................................A-1
Ports and Jacks ........................................................A-2
Built-In Microphone ...............................................A-2
CATV-In Jack .........................................................A-2
DC-In Jack ......................................... .....................A-2
DVI-Out Port ..........................................................A-2
Headphone-Out Jack ...............................................A-2
Line-In Jack ............................................................A-2
Microphone-In Jack ................................................A-3
Mini-IEEE 1394a Port ............................................A-3
Parallel Port .............................................................A-3
PS/2 Port .................................................................A-3
RJ-11 Phone Jack ....................................................A-3
RJ-45 LAN Jack ......................................................A-4
S/PDIF-Out Jack .....................................................A-4
Security Lock Slot ..................................................A-4
Serial Port ...............................................................A-4
S-Video-Out Port ........................................... .... .... .A-4
USB 2.0/1.1 Ports ...................................................A-4
XVI
Preface
NVIDIA Video Driver Controls
NVIDIA Video Driver Installation .........................B-1
NVIDIA Display Properties ....................................B-2
Display Devices .......................................................B-6
Attaching Other Displays ........................................B-7
Display Modes .........................................................B-9
Enabling TV Display .............................................B-10
ATI Video Driver Controls
ATI Video Driver Installation ................................. C-1
ATI Mobility Radeon X800 Properties ...................C-2
Display Devices .......................................................C-4
Attaching Other Displays ........................................ C-5
Display Modes .........................................................C-6
Clone Mode .............................................................C-7
Extended Desktop Mode .........................................C-8
Enabling TV Display .............................................C-11
1.8" Top Case LCD
BIOS Setting ...........................................................D-2
Using the LCDAP Program .....................................D-3
LCDAP Files ........................................................ .D-5
Adding Files .........................................................D-5
Selecting & Configuring Files to Display ............D-6
Specifications
Processor Types .......................................................E-2
Core Logic ...............................................................E-2
Security ....................................................................E-2
Memory ....................................................................E-2
BIOS ........................................................................E-2
LCD .........................................................................E-2
Top Cover LCD .......................................................E-2
Video Card Options .................................................E-3
Storage Options ........................................................E-3
Audio .......................................................................E-4
Keyboard & Pointing Device ................................... E-4
PCMCIA ..................................................................E-4
I/O Ports ...................................................................E-4
Communication ........................................................E-5
Card Reader .............................................................E-5
Power Management .................................................E-5
Power .......................................................................E-5
Environmental Spec .................................................E-5
Physical Dimensions & Weight ............................... E-6
Optional ...................................................................E-6
XVII
Preface
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 The Storage Devices (hard disk, optical device options, 3-in-1 Card Reader, PC Card), Mail Pro-
gram, Mouse, Audio & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software, or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s TV Tuner, wireless, Bluetooth, and camera modules (some of
which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A A definition of the interface, ports/jacks which allow your computer communicate with external
devices.
• Appendix B Information on the NVIDIA Video driver controls.
• Appendix C Information on the ATI Video driver controls.
• Appendix D A guide to the computer’s 1.8" LCD.
• Appendix E The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Not Included
Operating Systems (e.g. Windows XP etc.) and applications (e.g. word processing, spreadsheet and database pro-
grams) have their own manuals, so please consult the appropriate manuals.
1 - 2 Overview
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the following operating systems:
• Microsoft Windows XP (Home & Professional Editions)
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 6. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
1
Overview 1 - 3
1
Quick Start Guide
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet,
and connect the AC power cord to the AC adapter.
5. Move and hold the LCD latches outwards, and the release the top cover.
6. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
7. Adjust the LCD panel to a comfortable viewing angle.
1
Shutdown
Please note that you
should always shut
your computer down
by choosing the Shut
Down/Turn Off Computer command from
the Start menu in Windows. This will help
prevent hard disk or
system problems.
1. LCD Latches
2. 1.8" TFT LCD Screen (see “1.8" Top Case LCD” on page D - 1)
2
11
1 - 4 Overview
Figure 1 - 1 - Top Panel with LCD Closed & AC Adapter In
Quick Start Guide
Getting to Know Your Computer
The graphics on the following pages will help you to become familiar with the basic functions, and to learn the
location of the various ports and components of your computer.
Model Differences
1
1 1
Model A
Standard Screen
1. Speaker Location
Model B
Wide Screen
1
Figure 1 - 2 - Model Differences
This manual refers to
the two notebook models pictured on this
page.
The designs vary
slightly in external design. Photographs
used throughout this
manual are of Model A
(Model B features a
wide screen).
Overview 1 - 5
1
Quick Start Guide
1.8" LCD
The 1.8" TFT Top Case LCD can be used to display company logos, personal photos, animated files etc. (see
below). Details on how to program the logos and pictures for the 1.8" LCD are available in Appendix D on
page D - 1.
1.8" LCD Power ON/OFF
Power to the 1.8" LCD may be toggled on/off by touching the metal rim which runs around the LCD. The 1.8"
LCD will remain on even if the computer is shut down but still powered by the battery (and will thus draw power
from the battery).
Logo Format
The 1.8" LCD supports the following logo formats:
24 bit depth Bitmap (.bmp) files 128 pixel wide * 160 pixel high
32 bit depth GIF or animated .GIF files 128 pixel wide * 160 pixel high
Figure 1 - 3 - Top View with LCD Panel Closed
Press to Toggle Power On/Off
Screen Rotation
The picture displayed on the LCD will rotate and invert depending on whether the lid is closed or open (if the
lid is open the picture will invert to display your picture or logo properly to anyone facing the open lid).
1 - 6 1.8" LCD
System Map: Top View with LCD Panel Open
Quick Start Guide
1
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the module(s) are
OFF if you are using the
computer aboard aircraft.
Use the AP-key Buttons
to toggle power to the
WLAN, Bluetooth and
PC Camera modules.
1
3
4
2
5
6
3
8
9
3 3
Figure 1 - 4 - Top View with LCD Panel Open
10
7
1. Optional Built-In PC
Camera
2. LCD
3. Speakers (Mod el A -See
Figure 1 - 2)
4. LED Indicators
5. AP-key Buttons
6. Power Button
7. Built-In Microphone
8. Keyboard
9. TouchPad & Buttons
10. Audio "DJ" Display
Panel (Including LED
Indicators)
5
6
4
System Map: Top View with LCD Panel Open 1 - 7
1
Quick Start Guide
LED Indicators
The two sets of indicators on the computer display
helpful information about the current status of the
computer. There are also indicators located on the display panel of the Audio "DJ".
Table 1 - 1 - LED Indicators
Icon Color Description
Green Hard Disk Activity
Green
Green
*Note: If you have a second battery then a separate indicator will appear for it.
The (optional) Wireless LAN
Module is powered On
The (optional) Bluetooth
Module is powered On
Table 1 - 2 - Audio "DJ" LED Indicators
Icon Color Description
Green DC Power is Plugged In
Blinking Green
Orange The Battery is Charging
Green
The Computer is in Standby
Mode
The Battery is Fully
Charged
*
Blinking Orange
Red Battery Error
Blinking Orange E-mail Received
Green Number Lock Activated
Green Caps Lock Activated
Green
The Battery Has Reached
Critically Low Power Status
Scroll Lock Activated (to
activate press Fn & ScrLk)
1 - 8 System Map: Top View with LCD Panel Open
Quick Start Guide
1
AP-key Buttons
These buttons access the internet, e-mail and toggle
power to the optional PC Camera, Wireless LAN and/
or Bluetooth modules. Make sure you install the driver
to enable the AP-key Button functions (refer to “What
to Install” on page 4 - 1).
Table 1 - 3 - AP-key Buttons
AP-key Buttons Function
Activate the Default E-mail
Program
Activate the Default Internet
Browser
Toggle power to the optional PC
Camera module
T oggle power to the optional WLAN
module
Toggle power to the optional
Bluetooth module
Function Keys & Numeric Keypad
The keyboard has an embedded numerical keypad for
easy numeric data input (see Figure 1 - 5).
Activate the Number Lock feature by pressing the
Num Lk key at the top right of the keyboard. You may
check if Number Lock is enabled or not by looking at
the LED status indicators.
Other Keyboards
If your keyboard is damaged or you just want to make
a change, you can use any standard USB keyboard.
The system will detect and enable it automatically.
However special functions/AP-key Buttons unique to
the system’s regular keyboard may not work.
System Map: Top View with LCD Panel Open 1 - 9
1
Quick Start Guide
Keys Description
Fn Function Key
Fn + F3 Mute Toggle
Fn + F4 Sleep Toggle
Fn + F5 Decrease Audio Volume
Fn + F6 Increase Audio Volume
Fn + F7 Display Toggle
Fn + F8 Decrease LCD Brightness
Fn + F9 Increase LCD Brightness
Fn +
NumLk
Fn + ScrLk Scroll Lock Toggle
Number Lock Toggle
Table 1 - 4 - Function Keys
Figure 1 - 5 - Keyboard
Function Keys
NumLk & ScrLk Keys
Numeric Keypad
Fn Key
Special Characters
Some software applications allow the number-keys to be used with Alt to
produce special characters. These special characters can only be produced
by using the numeric keypad. Regular number keys (in the upper row of the
keyboard) will not work. Make sure that NumLk is on.
1 - 10 System Map: Top View with LCD Panel Open
System Map: Front & Rear Views
Quick Start Guide
1
4 4
1
2
3
2
1
5
Audio "DJ" Player
The built-in standalone audio CD player gives you direct hardware control for audio CDs (MP3
compatible) when the computer is shut down, but has a working power source.
6
8 97
10
11
12
Overheating
To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)
while the computer is in use.
13
Figure 1 - 6
Front & Rear Views
1. LCD Latches
2. Audio "DJ" Player
Controls
3. Audio "DJ" LED
4. Speakers
5. Consumer Infrared
Transceiver (Works
with Optional TV
Tuner Remote
Control)
6. DVI-Out Port
7. Parallel Port
8. 2 * USB Ports
9. S-Video-Out Port
10. PS2 Port
11. Serial Port
12. Vent/Fan Intake
13. Security Lock Slot
System Map: Front & Rear Views 1 - 11
1
Quick Start Guide
System Map: Left View
Figure 1 - 7
Left View
1. 3-in-1 Card Reader
2. Infrared Transceiver
(see page 2 - 12)
3. Speaker
4. Secondary Device Bay
Release Latch
5. Secondary (Optional)
Device Bay
6. RJ-45 LAN Jack
7. PC Card Slot
2nd Battery
Do not try to startup the
computer from the 2nd
battery only.
1
2
3
4
6 7
5
3-in-1 Card Reader Formats
The card reader allows you to use the most popular digital storage card formats (see below). To remove any inserted cards, click the Safely Remove Hardware icon in the
Windows taskbar and follow the instructions on page 2 - 7 in order to prevent system errors (DO NOT PULL THE CARD OUT OF THE SLOT).
MMC (MultiMedia Card) SD (Secure Digital) MS (Memory Stick)
Secondary (Optional) Device Bay Options
The following are the device options available for the Secondary Device Bay:
3-Mode Floppy Disk Drive
2nd Battery
DVD-Dual OR Combo Drive
2nd Parallel (PATA) Hard Disk Drive
7-in-1 Card Reader
Warning: DO NOT attempt to change any device in the bay while the system is powered on, and make sure it is fully locked in position (see page 6 - 9).
1 - 12 System Map: Left View
System Map: Right View
1
6 7 8 9 8
2
3 4 5
Changing DVD Regional Codes
Go to the Control Panel and double-click System >
Hardware (tab), click Device Man ager, then click the
+ next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties box,
and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see
“DVD Regional Codes” on page 2 - 5).
DVD region detection is device dependent, not OSdependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.
Quick Start Guide
Figure 1 - 8 - Right View
1. Primary Optical Device Bay (for
10
11
CD/DVD Type Device)
2. Headphone-Out Jack
3. Microphone-In Jack
4. S/PDIF-Out Jack
5. Line-In Jack
6. Mini-IEEE 1394a Port
7. RJ-11 Phone Jack
8. 2 * USB 2.0 Ports
9. Speaker
10. DC-In Jack
11. CATV Jack (Enabled with
Optional Mini-PCI TV Tuner
Only)
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a
sharpened pencil or similar object that may break and become
lodged in the hole.
1
System Map: Right View 1 - 13
1
Quick Start Guide
System Map: Bottom View
Figure 1 - 9
Bottom View
1. Battery
2. Speakers
3. Hard Disk Bay/TV Tuner
Cover
4. Video Card Cover
5. CPU Cover
6. Vent/Fan Intake
The CPU is not a user
serviceable part.
Opening this compartment, or accessing the
CPU in any way, may
violate your warranty.
CPU
4
5
6
6 6 6
3
2
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 4 - 9 for full
instructions.
2
1 - 14 System Map: Bottom View
Quick Start Guide
Windows XP Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can cu stomize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Figure 1 - 10
Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu. The Control Panel allows you to configure the settings for most of the
key features in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic control p anels for
many of the features, however many new control panels are added (or existing ones are enhanced) when you
install the drivers listed in Table 4 - 1, on page 4 - 6. To see all controls it may be necessary to toggle off Category View.
1
Windows XP Start Menu & Control Panel 1 - 15
1
Quick Start Guide
Video Features
Video Driver Controls
This computer features two different (NVIDIA GeForce 6800 or ATI M28) PCI Express video card options
(see “Video Card Options” on page D - 3). If you are unsure which video card your model features, then go to
the BIOS and check “VGA Card:” under System Information in the Advanced menu (see “System Information
(Advanced Menu)” on page 5 - 8).
You can switch display devices, and configure display options, from the Display Properties control panel in
Windows as long as the appropriate video driver is installed. For more detailed video information see “NVIDIA
Video Driver Controls” on page B - 1 or “ATI Video Driver Controls” on page C - 1 as appropriate for your
video card option.
To access Display Properties in Windows:
1. Click Start, point to Settings and click Control Panel (or just click Control Panel).
2. Double-click Display (icon) - In the Appearances and Themes category.
3. Click Settings (tab) in the Display Properties dialog box.
4. Move the slider to the preferred setting in Screen area/resolution (Figure 1 - 11 on page 1 - 17).
5. Click the arrow, and scroll to the preferred setting In Colors/Color quality (Figure 1 - 11 on page 1 - 17).
6. You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties. Click Settings (tab) and adjust as above.
7. Open the Display Properties control panel, and click Advanced (button) (Figure 1 - 11 on page 1 - 17) to
bring up the Advanced properties tabs. Clicking through these tabs (NVIDIA or ATI) allows you to make any
video adjustments you require.
1
2
3
1 - 16 Video Features
Quick Start Guide
NVIDIA Display Properties
1
1
2
3
ATI Display Properties
1
2
3
Figure 1 - 11 - Display Properties Desktop
Video Features 1 - 17
1
Quick Start Guide
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor/external Flat Panel Display or TV as
your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the S-Video-Out
Port. The following display modes are available (see“NVIDIA Video Driver Controls” on page B - 1 or “ATI
Video Driver Controls” on page C - 1 for details).
NVIDIA Display Mode Description
Single One of the connected displays is used as the display device
Clone Both connected displays output the same view
Dualview
Horizontal/Vertical Span
ATI Display Mode Description
Single One of the connected displays is used as the display device
Multiple - Clone Mode Both connected displays output the same view
Multiple - Extended Desktop Mode
1 - 18 Video Features
Both connected displays are treated as separate devices, and
act as a virtual desktop
Both connected displays are treated as a single device, and
act as a virtual desktop
Both connected displays are treated as separate devices, and
act as a virtual desktop
Table 1 - 5 - Display Options
Quick Start Guide
Power Management Features
The Power Options cont rol panel in Windows (see page 1 - 14) allows you to configure power management
features for your computer. You may conserve power throug h individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 12). Pay at-
tention to the instructions on battery care in “Battery Information” on page 3 - 9.
Figure 1 - 12 - Power Options
The computer’s power button, sleep button (Fn + F4 key combination), and closing the computer’s lid may
be set to send the computer in to either Standby or Hibernate mode.
1
Power Saving and Performance
Power Schemes may have an affect on your computer performance (see “Power Schemes” on page 3 - 4).
Power Management Features 1 - 19
1
Concise User’s Guide
1 - 20
Storage Devices, Mail Program, Mouse, Audio & Printer
Chapter 2: Storage Devices, Mail Program, Mouse, Audio & Printer
Overview
Read this chapter to learn more about the following main features and components of the computer:
• Hard Disk Drive
• Optical Device
• 3-in-1 Card Reader
• PC Card Slot
• Auto Mail Checker
• TouchPad and Buttons/Mouse
• Audio Features
• Audio "DJ" CD Player
• Configuring the Infrared Settings for FIR
• Adding a Printer
2
Overview 2 - 1
Storage Devices, Mail Program, Mouse, Audio & Printer
2
Before attempting to
access any of the internal components of
your computer please
ensure that the machine is not connected
to the AC power, and
that the machine is
turned off and any batteries are removed.
Also ensure that all peripheral cables, including phone lines, are
disconnected from the
computer.
Power Safety
Figure 2 - 1
Hard Disk Location
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk
can be taken out to accommodate other 2.5" serial (SATA) or parallel (PATA)
hard disk drives with a height of 9.5 mm (see “Storage Options” on page E -
3 for details).
The hard disk is accessible from the bottom of your computer as seen below (both parallel and serial connectors are provided). Further details on removing and inserting the hard disk are available in “Upgrading the Hard Disk
Drive(s)” on page 6 - 4.
Note that the Secondary (Optional) Device Bay supports parallel (PATA)
hard disks only.
1
1
Parallel HDD
Connector
Serial HDD
Connector
2 - 2 Hard Disk Drive
Storage Devices, Mail Program, Mouse, Audio & Printer
Optical Device
There is a bay for a 5.25" optical (Combo or DVD-Dual) device (12.7mm
height). The actual device will depend on the model you purchased. The o ptical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD
onto the disc tray with label-side facing up (use just enough force for the disc
to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock
“clicks” and you are ready to start. The busy indicator will light up while
data is being accessed, or while an audio/video CD, or DVD, is playing. If
power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole to open the tray.
1
2
3
2
1
3
Sound Volume
Adjustment
How high the sound
volume can be set depends on the setting of
the volume control
within Windows. Click
the Volume icon on the
taskbar to check the
setting.
Peripherals must be
connected before you
turn on the system.
Figure 2 - 2
Optical Device
2
Optical Device 2 - 3
Storage Devices, Mail Program, Mouse, Audio & Printer
2
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency
eject hole. However
please do NOT use a
sharpened pencil or
similar object that may
break and become
lodged in the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it.
This may cause the
system to “crash”.
CD Emergency
Eject
Proper handling of your CDs/DVDs will prevent them from being damaged.
Please follow the advice below to make sure that the data stored on your CDs/
DVDs can be accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical Device
Storage Devices, Mail Program, Mouse, Audio & Printer
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 13.
.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
3
4
5
6China
Western Europe, Japan,
South Africa, Middle East &
South-East Asia, Taiwan,
South Korea, The Philippines,
Indonesia, Hong Kong
South & Central America,
Mexico, Australia,
New Zealand
N Korea, Russia, Eastern
Europe, India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Optical Device 2 - 5
Storage Devices, Mail Program, Mouse, Audio & Printer
2
Card Reader Cover
Make sure you keep
the cover in the card
reader when not is
use. This will help prevent foreign objects
and/or dust getting in
to the card reader.
Removable Disks
Figure 2 - 4
& 3-in-1 Card
Reader
3-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push
the card into the slot and it will appear as a removable device. The following
formats can be read by the card reader (see over for instructions on removing
a card):
• SD (Secure Digital)
• MMC (MultiMedia Card)
• MS (Memory Stick)
The cards will appear as removable disks on the computer and can be accessed
in the same way as your hard disk (s). For further information on the optional
7-in-1 Card Reader, see “The 7-in-1 Card Reader Module” on page 7 - 7.
2 - 6 3-in-1 Card Reader
Storage Devices, Mail Program, Mouse, Audio & Printer
Removing Cards from the Card Reader
To remove any inserted cards, click the Safely Remove Hardware icon in
the Windows taskbar and follow the instructions below in order to prev ent sys-
tem errors (DO NOT PULL THE CARD OUT OF THE SLOT).
1. Click the icon in the taskbar, and click to select the card from the pop-up list.
2. A “’Safe To Remove Hardware” bubble will pop-up to indicate you may now
safely remove the card from the reader slot.
OR
1. Right-click the icon in the taskbar, and click “Safely Remove Hardware”.
2. Select the device from the list and click Stop > OK.
3. A “’Safe To Remove Hardware” bubble will pop-up to indicate you may now
safely remove the card from the reader slot.
2
Figure 2 - 5
Safely Remove
Hardware (Click)
Figure 2 - 6
Safely Remove
Hardware (Right-Click)
3-in-1 Card Reader 2 - 7
Storage Devices, Mail Program, Mouse, Audio & Printer
2
PC Card Slot
The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC
Card. Make sure you install the driver for the PC Card (see “What to Install”
on page 4 - 1).
Inserting and Removing PC Cards
• Align the PC Card with the slot and push it in until it locks into place.
• To remove a PC Card, simply press the eject button next to the slot.
Figure 2 - 7
PC Card Slot
1
1
2 - 8 PC Card Slot
Storage Devices, Mail Program, Mouse, Audio & Printer
Auto Mail Checker
After you have installed the driver for the Auto Mail Checker program (see
“What to Install” on page 4 - 1) you may then configure it to give you noti-
fication when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your
default mail program does not need to be open.
The Auto Mail Checker appears as an icon in the taskbar (if you do not
see the icon in the taskbar go to Start > Programs/All Programs > Auto
Mail Checker > Auto Mail Checker). Clicking on the icon will bring up the
following options menu. If you have not input your mail account data, then
you will be prompted to do so.
Select Open to bring up the control panel for the program.
2
Figure 2 - 8
Auto Mail Checker
(Startup Menu)
Auto Mail Checker 2 - 9
Storage Devices, Mail Program, Mouse, Audio & Printer
You may then configure the options for your mailserver, name, password, pro-
2
Check with your Internet Service Provider,
network administrator
or Mail Service provider for details on what to
put on these pages.
Auto Mail Checker
Account Setup and
Note
Figure 2 - 9
Options
gram and method(s) of notification.
2 - 10 Auto Mail Checker
Storage Devices, Mail Program, Mouse, Audio & Printer
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a
mouse to your computer through one of the USB ports. The TouchPad buttons
function in much the same way as a two-button mouse. The central button may
be configured to function as you require.
Configuring the TouchPad and Buttons
Once you have installed the TouchPad drivers (see “What to Install” on
page 4 - 1) you can configure the functions (TouchPad tapping, buttons,
scrolling, pointer motion and sensitivity options) by double-clicking the
TouchPad driver icon on the taskbar. You will find further information at
www.synaptics.com.
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions.
Be sure to check the
device’s user documentation for details.
Figure 2 - 10
Mouse Properties
2
TouchPad and Buttons/Mouse 2 - 11
Storage Devices, Mail Program, Mouse, Audio & Printer
2
Audio Features
You can configure the audio options on your computer from the Sounds and
Sound Volume
Adjustment
How high the sound
volume can be set using the volume control
knob depends on the
setting of the volume
control within Win-
dows. Click the
Speaker icon on the
taskbar to check the
setting.
Figure 2 - 11
Realtek Audio
Configuration
Menus
Audio Devices Windows control panel (see Figure 1 - 10 on page 1 - 15),
or from the Sound Effect Manager icon in the taskbar/control panel (this
will bring up the Realtek Audio Configuration menus). The volume may also
be adjusted by means of the Fn + F5/F6 key combination.
2 - 12 Audio Features
Storage Devices, Mail Program, Mouse, Audio & Printer
Audio "DJ" CD Player
The built-in standalone audio CD player gives you direct hardware control for
audio CDs/DVDs when the computer is shut down, but has a working power
source.
1. Make sure that the computer is shut down (i.e. the operating system is not
running) but you have a working power source (either battery or AC Power).
2. Press the Audio "DJ" power button.
3. Press the open button on your CD/DVD device (or press the stop button
twice) and carefully place an audio CD onto the disc tray with label-side
facing up (DVD drives will also play audio CDs).
4. Gently push the CD/DVD tray in until its lock “clicks” and you are ready to
start.
5. The Audio Format Indicator will flash while data is being accessed and will
then display the audio format of the CD/DVD (CD or MP3).
6. The LED will display the number of tracks.
7. Click the play/pause button to start the CD/DVD.
8. You can control the CD/DVD tracking and volume from the control panel.
9. Use the stop button to stop the disc, or press it twice to eject the disk.
10. The player can be turned off by pressing the power button again.
7
Disk Eject Warning
Don’t try to eject a CD/
DVD while the system
is accessing it. This
may cause the system
to “crash”. Stop the
disk first then eject it,
or press the stop button twice.
2
Audio "DJ" CD Player 2 - 13
Storage Devices, Mail Program, Mouse, Audio & Printer
2
If you have included
the optional TV Tuner
in your purchase configuration, you can use
the supplied remote
control unit to control
the Audio "DJ".
TV Tuner Option
Figure 2 - 12
Audio "DJ"
Controls
2
1
3
5
1. Audio "DJ" Power Switch
2. Mode Button (CD, MP3)
3. Shuffle (loop, in order, shuffle)
4. LED Display
5. Audio Format Indicator
6. Previous Track
7. Next Track
8. Play/Pause
9. Stop (press twice to eject the CD/DVD)
10. Volume Up/Down
4
4
6
8
7
9
10
2 - 14 Audio "DJ" CD Player
Storage Devices, Mail Program, Mouse, Audio & Printer
Configuring the Infrared Settings for FIR
To configure your computer for Fast Infrared (FIR) communication follow
these steps:
1. Click Start, point to Settings and click Control Panel (or click Start > Control Panel).
2. Double-click Wireless Link (Printers and Other Hardware Category)
icon.
3. Click Hardware (tab), and click the Properties button, then click the
Advanced (tab).
4. Select “Infrared Transceiver A” and change the Value to “HP HSDL-
2300/3600”.
5. Click OK > OK.
For further information, please refer to the manual of the device you wish to
connect.
The computer’s Consumer Infrared transceiver may be used with the remote
control supplied with the optional TV Tuner (see “System Map: Front &
Rear Views” on page 1 - 11 & “The TV Tuner Module” on page 7 - 8).
Infrared
Communication
The infrared transceiver operates on a “Line
of Sight”.
Make sure nothing is
blocking the “Line of
Sight” between your
system’s transceiver
and the destination’s
transceiver.
2
Configuring the Infrared Settings for FIR 2 - 15
Storage Devices, Mail Program, Mouse, Audio & Printer
2
Adding a Printer
The most commonly used peripheral is a printer. The following conventions
Parallel Printer
After setting up the
printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the
Parallel port.
will help you to add a printer, however it is always best to refer to the printer
manual for specific instructions and configuration options.
USB Printer
Most new printers have a USB interface connection. You may use any one of
the ports to connect the printer.
Install Instructions:
Turn the printer ON,
then turn ON the computer.
Windows will identify
the printer and either
load one of its own
drivers or ask you to
supply one. Follow the
on-screen instructions.
1. Set up the printer according to its instructions (unpacking, paper tra y, toner/
ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or
ask you to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the
sidebar.
2 - 16 Adding a Printer
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer uses the
ACPI power management system. Power management conserves power by
controlling individual components of the computer (the monitor and hard disk
drive) or the whole system.
This chapter covers:
• The Power Sources
• T urning on the Computer
•Power Schemes
• System Power Options
• Configuring the Power Button
• Battery Information
Advanced Configuration and Power Interface
The ACPI interface provides the computer with enhanced power saving techniques and gives the operating system (OS) direct control over the power and
thermal states of devices and processors. For example, it enables the OS to set
devices into low-power states based on user settings and information from applications. ACPI is fully supported in Windows XP.
OS Note
Power management
functions will vary
slightly depending on
your operating system.
For more information it
is best to refer to the
user’s manual of your
operating system.
3
Overview 3 - 1
Power Management
2nd Battery
3
If you have included
the secondary battery
in your purchase configuration, do not try to
startup the computer
from the 2nd battery
only.
The computer can be powered by either an AC adapter or a battery pack.
AC Adapter
Use only the AC adapter that comes with your computer. The wrong type of
AC adapter will damage the computer and its components.
1. Attach the AC adapter to the DC-in jack on the right of the computer.
2. Plug the AC power cord into an o utlet, and th en connect the AC p ower cord
to the AC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or
when an electrical outlet is unavailable. Battery life varies depending on the
applications and the configuration you're using. To increase battery life, let
the battery discharge completely before recharging (see “How do I com-
pletely discharge the battery?” on page 3 - 12).
We recommend that you do not remove the primary battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.
The Power Sources
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press
the power button on the front panel.
When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds
(pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure
this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press
the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button as Standby or Hibernate Button
If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the
OS’s “Power Options” control panel to set the power button to send the system into
Standby or Hibernate mode (see your OS’s documentation, or “Configuring the
Power Button” on page 3 - 8 for details).
Power Management
Shutdown
Note that you should
always shut your computer down by choosing the Shut Down/
Turn Off Computer
command from the
Start menu in Windows. This will help
prevent hard disk or
system problems.
3
Turning on the Computer 3 - 3
Power Management
Power Schemes
3
Resuming
Operation
The system can resume from Monitor or
Hard Disk Standby by
pressing a key on the
keyboard.
Figure 3 - 1
Power Schemes
You can set your computer to conserve power through individual components
by means of Power Schemes. You can also adjust the settings for each
scheme to set the monitor to turn off after a specified time, and the computer's
hard disk motor to turn off if the hard disk drive has not been accessed for a
specified period of time (if the system reads or writes data, the hard disk motor
will be turned back on). The schemes may also be set to set a specified time
for the system to enter Standby or Hibernate modes (see “System Power Op-
tions” on page 3 - 6).
3-4Power Schemes
Each Windows Power Scheme will also adjust the processor performance of
your machine in order to save power. This is worth bearing in mind if yo u are
experiencing any reduced performance (especially under DC/battery power).
Choose the Home/Office Desk scheme for maximum performance when the
computer is powered from an AC power source. Choose the Max Battery
scheme (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving
when the computer is battery (DC power) powered.
Windows will use Portable/Laptop as the default scheme.
Power Management
3
Power Schemes 3 - 5
Power Management
System Power Options
You can use the system power options to stop the computer’s operation and
3
restart where you left off. This system features Standby and Hibernate sleep
mode levels (Hibernate mode will need to be enabled by clicking the option
in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on
page 3 - 7).
Hibernate Mode vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you
need to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left
off (what was on your desktop) without reopening the application(s) and
file(s) you last used.
You can use either method depending on your needs.
Standby Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the system on standby instead of in hibernation. It takes a longer time to wak e up the
system from Hibernate mode than from Standby mode.
3 - 6 System Power Options
Standby
Standby saves the least amount of power, but takes the shortest time to return
to full operation. During Standby the hard disk is turned off, and the CPU is
made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which
you specify in the operating system, it will enter Standby mode to save power.
Hibernate
Hibernate uses no power and saves all of your information on a part of the
HDD before it turns the system off. Although it saves the most power it takes
the longest time to return to full operation. You can set your computer to automatically enter Hibernate mode when the battery power is almost depleted.
You will need to enable Hibernate mode from the Hibernate tab in the Power
Options control panel. The system will resume from Hibernate mode by
pressing the power button.
Power Management
System Resume
The system can resume
from Standby mode by:
• Pressing the power
button
• Pressing a key on the
keyboard
• An alarm resume that
is enabled and
expires
• An incoming call
received on the
modem (if enabled)
• Network card activity
(if enabled)
3
Figure 3 - 2
Enable Hibernation
System Power Options 3 - 7
Power Management
Configuring the Power Button
The power button may be set to send the computer in to either Standby or Hi-
3
Figure 3 - 3
Power Options
(Advanced - Power
Buttons)
bernate mode (Figure 3 - 3). In Standby mode, the LED will flash green.
In Hibernate mode the LED will be off. If you are in a power saving mode
set to save power through individual components (e.g. hard disk, monitor), the
LED will remain green.
Power Button Sleep/ResumeLid
You may also configure the Sleep/Resume key combination (Fn + F4) from the
menu illustrated in Figure 3 - 3. In Windows this is referred to as the Sleep button.
3 - 8 Configuring the Power Button
(Sleep) Button
Sleep Button
Power Management
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery
FAQ” on page 3 - 12 for instructions on how to do this).
Battery Life
Your computer’s battery life is dependent upon many factors, including the
programs you are running, and peripheral devices attached. Power Options
(you may set low battery Alarms and actions, and check the Power Meter
from the Power Options control panel), and settings in the OS will help prolong the battery life if configured appropriately.
If 2 Batteries Installed
Low Battery
Warning
When the battery is
critically low, immediately connect the AC
adapter to the computer or save your work,
otherwise, the unsaved data will be lost
when the power is depleted.
Figure 3 - 4
Power Options
(Alarm & Power
Meter)
3
Battery Information 3 - 9
Power Management
Battery life may be shortened through improper maintenance. To optimize
3
Conserving
Battery Power
To conserve battery power:
Lower the brightness level of the LCD display. The
system will decrease LCD
brightness slightly to save
power when it is not powered by the AC adapter.
Close modem or communication applications
when they are not being
used.
Remove any unused PC
Cards from the computer
(PC Cards quickly use up
battery power even if the
system enters sleep
mode).
Disconnect any unnecessary external devices.
the life and improve its performance, fully discharge and recharge the
battery at least once every 30 days.
We recommend that you do not remove the primary battery yourself. If you
do need to remove the battery for any reason see “Removing the Primary Bat-
tery” on page 6 - 3.
1.8" LCD Top Case & Battery Power
The 1.8" LCD will remain on even if the computer is shut down (and will thus draw
power from the battery). Power to the 1.8" LCD may be toggled on /off by touching
the metal rim which runs around the LCD (see “1.8" Top Case LCD” on page D
- 1). Make sure you turn off the LCD after shutting down the computer.
Recharging the Battery with the AC Adapter
The battery pack automatically recharges when the AC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it
will take several hours to fully recharge the battery. When the computer is
turned off but plugged into an electrical outlet, battery charge time is less. Refer to “LED Indicators” on page 1 - 8 for information on the battery charge
status, and to “Battery Information” on page 3 - 9 for more information on
how to maintain and properly recharge the battery pack(s).
3 - 10 Battery Information
Proper Handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after
being dropped), or any unusual smells emanating from the no tebook batter y, shut
your computer down immediately and contact your service center. If the battery has
been dropped we do not recommend using it any further, as even if the computer
continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire. It is recommended that you replace your computer
battery every two years.
Power Management
3
Battery Information 3 - 11
Power Management
Battery FAQ
Caution
3
Danger of explosion if
battery is incorrectly
replaced.
Replace only with the
same or equivalent
type recommended by
the manufacturer. Discard used battery according to the
manufacturer’s instructions.
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery.
Don’t turn off the computer by yourself (save and close any critical files, and
make sure you have closed all open applications in order to prevent any data
loss) even when you see a message that indicates the battery is critically low,
just let the computer use up all of the battery power and shut down on its own.
Disable the Power Options functions in the Control Panel, especially any
Alarms (unclick the tickboxes - see 3 - 9) and Schemes (change all the settings to Never - see page 3 - 4).
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light
changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
3 - 12 Battery Information
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and
utilities essential to the operation or improvement
of some of the computer’s subsystems. The system
takes advantage of some newer hardware components for which the latest versions of most available
operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t
be auto-configured with an appropriate driver or
utility during operating system installation. Instead,
you need to manually install some system-required
drivers and utilities. This chapter covers driver and
utility installation instructions for Windows XP
(Professional & Home).
What to Install
The Device Drivers & Utilities + User’s Manual
CD-ROM contains the drivers and utilities neces-
sary for the proper operation of the computer. The
drivers for all the optional modules (WLAN, Blue-
tooth, PC Camera and TV Tuner) are on the separate CD-ROMs supplied. Table 4 - 1, on page 4 -
6 lists what you need to install, and it is very im-
portant that the drivers are installed in the order indicated.
Module Driver Installation
The procedures for installing drivers for the
WLAN, Bluetooth, PC Camera and TV Tuner
modules are provided in Chapter 7 “Modules”.
Make sure that the drivers are installed in the order
indicated in Table 4 - 1, on page 4 - 6.
4
What to Install 4 - 1
Drivers & Utilities
Navigate (Browse..) to D:
4
You will notice that many of the instructions for driver
installation require you to “Navigate (Browse) to D:”.
We assume that you will install all drivers and utilities
from the built-in CD device and it is assigned to “Drive
D:”. In addition, all file extensions can be seen
In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and
some computers have the CD listed under a different
drive letter - e.g. if you have two hard drives (or hard
disk partitions) one may be designated as “Drive C:”
and the other as “Drive D:”. In this case the CD device
may be designated as “Drive E:” - Please make sure
you are actually navigating to the correct drive letter
for the CD device.
When you click the Browse (button) after clicking
Run in the Start menu you will see the “Look in:” dialog box at the top of the Browse window. Click the
scroll button to navigate to My Comput er to display
the devices and drive letters.
4 - 2 What to Install
Figure 4 - 1 - Navigate (Browse..) to..
Service Packs
Make sure you have installed the appropriate Service Pack before installing all the drivers. If you
are unsure of the Service Pack currently installed
see below.
Service Pack Installed
To see which Service Pack is currently installed on
your computer go to the General tab of the System
control panel. Right-click the My Computer icon on
the desktop or in the Start menu and select Proper-
ties. The Service Pack currently installed on your system will be listed under the “System:” heading. (If no
Service Pack information is listed, then no Service
Pack is installed.)
Drivers & Utilities
Windows XP Service Pack 2
Make sure you install Windows XP Service Pack 2
(or a Windows XP version which includes Service
Pack 1) before installing any drivers. Service
Pack 1 includes support for USB 2.0.
If you have upgraded the system by installing Ser-
vice Pack 2 (i.e. your Windows XP version does not
include Service Pack 2) then follow these instructions:
1.Click Start (menu), point to Settings and click
Control Panel (or click Start >Control Panel).
2.Double-click System (icon); System (icon) is in
Performance and Maintenance (category).
3.Click the Hardware (tab) > Device Manager (button).
4.Click “+” next to Other Devices (if its sub-items
are not shown).
5.Right-click Universal Seria l Bus (USB) Control-
ler and select Uninstall > OK (if you don’t see the
item then there is no need to take any further action).
6.Restart the computer and it will find the USB 2.0
controller.
4
What to Install 4 - 3
Drivers & Utilities
Authorized Driver Message
If you receive a message telling you that the driver
you are installing is not authorized (Digital Signa-
ture Not Found), just click Continue Anyway to
4
ignore the message and continue the installation
procedure.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To
do this go to the Control Panel in the Windows OS
and double-click the Add/Remove Programs
item. If you see the individual driver listed (if not
see below), uninstall it, following the on screen
You will receive this message in cases where the
driver has been released after the version of Win-
dows you are currently using. All the drivers provided will have already received certification for
Windows.
prompts (it may be necessary to restart the computer). Go to the appropriate section of the manual to
complete the update/reinstall procedure for the
driver in question.
If the driver is not listed in the Add/Remove Pro-
grams item:
Version Conflict Message
During driver installation if you encounter any “file
version conflict” message, please click Yes to
choose to keep the existing (newer) version.
1. Click Start (menu), point to Settings and click
Control Panel (or click Start > Control Panel).
2. Double-click System (icon); System (icon) is in
Performance and Maintenance (category).
3. Click Hardware (tab) > Device Manager
(button).
4. Double-click the device you wish to update/
reinstall the driver for (click “+” to see sub-items).
5. Look for the Update Driver button (check the
Driver tab) and follow the on screen pr ompts.
4 - 4 What to Install
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the Notebook Driver Installation application will run automatically. If you want
to install the driver manually see “Manual Driver
Installation” on page 4 - 6.
1. Check the driver installation order from Table 4 -
1, on page 4 - 6 (the drivers must be installed
in this order) which is the same as that listed in
the driver installation screen menu.
2. Double-click to select the name of the driver you
wish to install.
3. Wait for the driver to start installing.
4. The computer may need to restart (check the
instructions in this chapter).
5. Make a note of the drivers you have installed.
6. To get back to the Driver Installation screen after
a restart click Start (menu) > Run... and
navigate (Browse..) to D:\setup.exe and click
OK.
OR
Double-click the My Computer icon, and then
double-click the CD icon.
Drivers & Utilities
4
Figure 4 - 2
Notebook Driver Installation Screen
Driver Installation 4 - 5
Drivers & Utilities
Manual Driver Installation
If you wish to install the drivers manually, click the Exit button to quit the Notebook Driver Installation
application, then follow the manual installation procedure for each driver. The manual installation procedure begins with instructions on how to browse to the executable file; “Click Start (menu) > Run
..”.
4
Windows XP Driver (SP2) Page # Windows XP Driver (SP2) Page #
Chipset 4 - 7 PCMCIA 4 - 11
Audio 4 - 8 Auto Mail Checker 4 - 11
Modem 4 - 8 LCDAP (for 1.8" LCD Programming) 4 - 12
Network (LAN) 4 - 9 Wireless LAN Modules 7 - 3 & 7 - 4
Video 4 - 9 Bluetooth Module 7 - 5
AP-Key Buttons 4 - 10 TV Tuner Drivers and Applications 7 - 9
TouchPad 4 - 10 PC Camera 7 - 11
Table 4 - 1 - Driver Installation Order
4 - 6 Driver Installation
Windows XP Drivers
This section covers driver and utility installation instructions for Windows XP (Professional & Home).
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installation procedure (other than when outlined in
the driver install procedure), click Cancel to
close the window, and follow the installation procedure.
Drivers & Utilities
Windows XP Service Pack 2
Make sure you install Windows XP Service Pack 2
(or a Windows XP version which includes Service
Pack 2) before installing any drivers. Service
Pack 2 includes support for USB 2.0.
If you have upgraded the system by installing Ser-
vice Pack 2 (i.e. your Windows XP version does not
include Service Pack 2) then follow the instructions
in “Windows XP Service Pack 2” on page 4 - 3.
Chipset (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click Chipset.
OR
Click S tart (menu) > Run... and navigate
(Browse..) to D:\Drivers\
01CHIPSET\Setup.exe and click OK.
2. Click Next > Yes > Next.
3. Click Finish to restart the computer.
4
Windows XP Drivers 4 - 7
Drivers & Utilities
Audio (WinXP)
1. Run the Notebook Driver Installation application and double-click Audio.
OR
4
Click Start (menu) > Run... and navigate
(Browse..) to D:\Drivers\
02AUDIO\Setup.exe and click OK.
2. Click Next (click Cancel if The Found New
Hardware Wizard appears).
3. Click Finish to restart the computer.
4. When the computer restarts click Cancel if
Modem (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click Modem.
OR
Click S tart (menu) > Run... and navigate
(Browse..) to D:\Drivers\
03MODEM\Setup.exe and click OK.
2. Click (button).
3. Click (button).
4. The modem is ready for dial-up configuration.
the The Found New Hardware Wizard
appears.
5. Click Yes to restart the computer (click Can-
cel if The Found New Hardware Wizard
appears after the restart).
Modem Country Selection
Go to the Phone and Modem Options control panel
(in the Printers and Other Hardware Category) and
check if the modem country selection is appropriate
for your country.
4 - 8 Windows XP Drivers
Drivers & Utilities
LAN (WinXP)
1. Run the Notebook Driver Installation application and double-click Lan.
OR
Click Start (menu) > Run... and navigate
(Browse..) to D:\Drivers\
04LAN\WinXP\SetupYukonWin.exe and
click OK.
2. Click Next.
3. Click the button to accept the license and
click Next.
4. Click Next > Install > Finish.
5. The network settings can now be configured.
Video (WinXP)
The installation method for the video driver will depend on whether your purchase option includes either an NVIDIA or ATI PCI-Express Video Card.
If you run the Notebook Driver Installation application it will automatically detect the appropriate
driver.
For NVIDIA PCI Express video cards see “NVID-
IA Video Driver Installation” on page B - 1.
For ATI PCI Express video cards see “ATI Video
Driver Installation” on page C - 1.
4
Windows XP Drivers 4 - 9
Drivers & Utilities
AP-Key Buttons (WinXP)
1. Run the Notebook Driver Installation application and double-click AP-key.
OR
4
Click Start (menu) > Run... and navigate
(Browse..) to D:\Drivers\
06APKey\Setup.exe and click OK.
2. Click Next.
3. Click Finish to restart the computer.
TouchPad (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click Touchpad.
OR
Click S tart (menu) > Run... and navigate
(Browse...) to D:\Drivers\
07TOUCHPAD\WINXP\Setup.exe and
click OK.
2. Click Next > Next > Next (click Continue
Anyway if asked if you want to continue at
any time).
3. Click Finish to restart the computer.
4. You may then configure the TouchPad as
outlined in “Configuring the T ouchPad and
Buttons” on page 2 - 11.
4 - 10 Windows XP Drivers
Drivers & Utilities
PCMCIA & Card Reader (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click PCMCIA.
OR
Click Start (menu) > Run... and navigate
(Browse...) to D:\Drivers\
08PCMCIA\setup.exe and click OK.
2. Choose the language you prefer, and click
OK.
3. Click Next > Finish.
Auto Mail Checker (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click Automail.
OR
Click S tart (menu) > Run... and navigate
(Browse..) to D:\Drivers\
09AUTOMAIL\SETUP.EXE and click
OK.
2. To continue click Next > Next > Finish.
3. Run the program from the Auto Mail
Checker in the Start menu (Start > Programs/All Programs > Auto Mail
Checker).
4. Click the icon in the taskbar to input the
e-mail account details.
5. For further details see “Auto Mail Checker”
on page 2 - 9.
4
Windows XP Drivers 4 - 11
Drivers & Utilities
LCDAP (WinXP)
1. Run the Notebook Driver Installation appli-
cation and double-click LCDAP.
OR
4
Click Start (menu) > Run... and navigate
(Browse..) to D:\Drivers\
10LCDAP\LCDAP.exe and click OK.
2. This will run the program (see “1.8" Top
Case LCD” on page D - 1 for further
instructions).
3. If you wish to copy the application to the
hard disk make sure you copy the whole
LCDAP folder to your hard disk (e.g. C:
drive).
Module Drivers
See the following pages for the driver installation
procedures for any modules included in your purchase option.
Wireless LAN (WinXP)
See the install procedure in “MSI 6855A (802.11b/
g) Wireless LAN Driver Installation” on page 7 3 or “ZCOM (802.11a/b/g) WLAN Module Driver
Installation” on page 7 - 4.
Bluetooth (WinXP)
See the install procedure in “Bluetooth Module
Driver Installation” on page 7 - 5.
TV Tuner (WinXP)
See the install procedure in “Installing the AverTV
Utility Software” on page 7 - 9, and “Installing the
InterVideo WinDVD 4 Software” on page 7 - 9.
PC Camera (WinXP)
See the install procedure in “Kenmec PC Camera
Driver Installation (WinXP)” on page 7 - 11 or
“Sertek PC Camera Driver Installation (WinXP)”
on page 7 - 11.
4 - 12 Module Drivers
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are making important ch anges
to the system (e.g. hard disk setup), then you should review this chapter first
and note the original settings found in Setup. Even if you are a beginner, keep
a record of the settings you find and any changes you make. This infor mation
could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what
you are doing. Many of the settings are required by the system, and changing
them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to
Setup and restore the
Setup Defaults with
<F9>.
5
Overview 5 - 1
BIOS Utilities
Phoenix cME FirstBIOS Notebook Pro
Copyright 1985-2003 Phoenix Technologies Ltd.
All Rights Reserved
BIOS Revision: V146 1.00.P01
KBC/EC Firmware Revision: 1.00.D8
VBIOS Revision: 5.41.02.18.AC-09/24/04
CPU = Intel(R) Pentium(R) 4 CPU 3.20GHz
1023M System RAM Passed
1024K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
ATAPI CD-ROM: TSSTcorpCD/DVDW TS-L532A
Fixed Disk 0: FUJITSU MHT2060BH
USB: Y-E DATA USB-FDU
Mouse intialized
Press <F2> to enter SETUP
POST Screen
1.BIOS information
2.CPU type
3.Memory status
4.Enter Setup prompt
5
appears only during
POST
Note: The POST
screen as pictured is
for guideline purposes
only. The POST
screen on your computer may appear
slightly different.
Figure 5 - 1
POST Screen
The Power-On Self Test (POST)
Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong.
If there is a problem that prevents the system from booting, it will display a
system summary and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will
load the operating system. Once that starts, you can’t get into Setup without
rebooting.
1
Boot Logo Screen
If you have enabled
the Boot Logo Screen
then the POST screen
will not appear.
can still press F2 to enter Setup (see “Boot
Logo Screen:” on
page 5 - 10).
You
3
4
2
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and
“non-fatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously
wrong with your system. Take the computer to your service representative or
authorized service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying
the problem (make a note of this message!) followed by the prompt:
• Press <F1> to resume
• <F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct configuration.
Press F2 to run the Setup program and try to correct the problem. If you still
get an error message after you change the setting, or if the “cure” seems even
worse, call for help.
BIOS Utilities
5
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
The Setup Program
The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The
5
prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a
few seconds after you turn on the system. If you get a “Key board Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combina-
tion and then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Program
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with five (5) menu headings. When
you select a heading, a new screen appears. Scroll through the features listed
on each screen to make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of
the screen. If these tools are confusing, press F1 to call up a General Help
screen, then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that
subject. The sub-menu screen that appears has a similar layout, but the Enter
key may execute a command.
BIOS Utilities
Setup Menus
The setup menus
shown in this section
are for reference only.
Your computer’s
menus will indicate the
configuration appropriate for your model and
options (and are subject to update without
prior notice).
5
The Setup Program 5 - 5
BIOS Utilities
Main Menu
PhoenixBIOS Setup Utility
Figure 5 - 2
Main Menu
5
Main
Main Advanced Security Boot Exit
Item Specific Help
System Time: [22:11:05]
System Date: [09/22/2004]
IDE Channel 0 Master [CD-ROM]
IDE Channel 0 Slave [None]
SATA Port 1 [60012MB SATA1]
SATA Port 2 [None]
Installed memory 1024 MB
Available to OS 1022 MB
Used by devices 2 MB
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
13
<Tab>, <Shift Tab>, or
<Enter> selects field.
System Time & Date
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If
you can change the date and time settings in your operating system, you will
also change these settings. Some applications may also alter data file s to reflect these changes.
5-6Main Menu
IDE Channel 0 Master/Slave
Pressing Enter here open s the sub-menu to show the conf iguration of either a
CD/DVD type Device or HDD on the computer’s IDE Channel 0. Use the
Auto (Type:) setting to have the items configured automatically for you.
SATA Port 1/2
Pressing Enter here opens the sub-menu to show the configuration of any
hard disks on the computer’s SATA Port 1 or 2. Use the Auto (Type:) setting
to have the items configured automatically for you.
Installed memory
This item contain information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed, the
amount used by devices, and the unused memory available to the operating
system (OS).
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities
Advanced Menu
Figure 5 - 3
Advanced Menu
5
Main Advanced Security Power Boot Exit
Setting items on this menu to incorrect
values may cause your system to malfunction.
System Information
I/O Device Configuration
Reset Configuration Data: [No]
Hyper Threading Technology: [Enabled]
Power On Beep [Disabled]
Boot Logo Screen: [Disabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Advanced
Setup Warning
PhoenixBIOS Setup Utility
Item Specific Help
System Information
Pressing Enter here will p rovide valuable information on your system including CPU type and speed etc. System Information will also display which video
card (NVIDIA or ATI) is installed on your computer.
5 - 8 Advanced Menu
I/O Device Configuration
The sub-menus under this item include options to configure the Serial port A
(Serial Mouse), Serial port B (Infrared) and Parallel (Printer) port. These
can be left to the default settings, however you may wish to use certain devices
that require settings to be adjusted accordingly. Check the documentation for
any such devices to see what settings are required.
BIOS Utilities
Flash Top Case Logo > I/O Device Configuration
This item allows you to enable the serial port for application programming of
the top case logo. After programming the logo make sure you reset the option
to “Disabled” (default) otherwise the serial port will not work.
PhoenixBIOS Setup Utility
Advanced
Advanced
I/O Device Configuration
Flash Top Case Logo: [Enabled]
Serial port A: [Enabled]
Serial port B: [Enabled]
Mode: [FIR]
Parallel port: [Enabled]
Mode: [ECP]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Disable:
Normal serial port A
function.
Enable:
Enables serial port A
for programming the top
case logo image.
Any serial port device
will not be able to
work when this setting
is enabled.
5
Figure 5 - 4
Advanced Menu - I/O
Device Configuration
Advanced Menu 5 - 9
BIOS Utilities
Reset Configuration Data:
This item is set to No as default. You can change the setting to Yes if you have
installed a new add-on which has reconfigured the system, resulting in such a
serious system conflict that the operating system is unable to boot.
Hyper-Threading Technology
Enable Hyper-Threading (it is “Enabled” by default) to increase performance
5
of your computer depending on the hardware and software you use (all the
processor options in this notebook series support Hyper Threading Technology). Hyper Threading is supported fully in Windows XP, but it is strongly
recommended you DO NOT enable this option in other operating systems. Once you have enabled Hyper-Threading, DO NOT disable the option. (If you do disable the option you will need to reinstall your operating
system.)
Power On Beep
Use this menu to enable/disable the single beep sound at the end of the POST.
This item is “Disabled” by default.
Boot Logo Screen:
This menu item allows you to enable/disable the Boot Logo Screen as the
computer starts up (it is “Disabled” by default). This will affect what sort of
POST screen you see.
5 - 10 Advanced Menu
Security Menu
BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Supervisor Password Is: Clear
Set Supervisor Password [Enter]
Password on boot: [Disabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Security
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Set Supervisor Password
You can set a password for access to the Setup utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a
Password on Boot (see over).
Figure 5 - 5
Security Menu
5
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
access to your machine as it boots up after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
Security Menu 5 - 11
BIOS Utilities
Password on boot:
Password Warning
Specify whether or not a password (supervisor or user password) should be
entered to boot the computer. If “Enabled” is selected, only users who enter a
correct password can boot the system (see the warning in the sidebar). The
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password,
then press Enter for the new password (without typing any password entry)
and Enter again to confirm the password clearance.
5 - 12 Security Menu
BIOS Utilities
Boot Menu
PhoenixBIOS Setup Utility
Main Advanced Security Exit
Boot priority order:
1: USB FDC:
2: Legacy Floppy Drives
3: SATA_1: FUJITSU MHT2060AT-(S1)
4: SATA_2:
5: IDE0_M: TSSTcorpCD/DVDW TS-L532A6: IDE0_S:
7: PCI LAN: B2 D0 Yukon PXE
8:
Excluded from boot order:
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
When you turn the computer on it will look for an operating system (e.g. WindowsXP) from the devices listed in this menu, and in this priority order. If it
cannot find the operating system on that device, it will try to load it from the
next device in the order specified in the Boot priority order. Item specific
help on the right is available to help you move devices up and down the order.
Boot
Item Specific Help
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves the
device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1 - 4> Loads default
boot sequence.
Figure 5 - 6
Boot Menu
Legacy Floppy
Drives
If you have a Legacy
Floppy Drive installed
in your Secondary
(Optional) Device Bay
it will appear in the
boot priority order.
If you remove the drive
and then reinsert it at a
later time, it will then
be excluded from the
boot order.
Use either the <X>
key, or press F9 to
load the Setup Defaults, to restore the
drive to the boot order.
5
Boot Menu 5 - 13
BIOS Utilities
Boot devices usually are hard drives, floppy drives, and CD/DVD-ROMs and
networks (LAN).
When you specify a device as a boot device on the Boot Menu, it requires the
availability of an operating system on that device. Most home computers
come with an operating system already installed on “Drive C:”.
5
5 - 14 Boot Menu
If you wish to boot from a CD/DVD-ROM you will need to add it to th e bo ot
order. As a general rule the order below is recommended:
1. Removable Devices (usually floppy disks)
2. CD-ROM/DVD-ROM type Device Drive
3. Hard Disk Drive
4. LAN (Network)
In everyday use you will usually boot from the hard drive, however there may
be occasions when it is advantageous to boot from a floppy disk (e.g. an external USB floppy disk drive) or CD-ROM/DVD-ROM.
Exit Menu
BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out
any changes you have made to the Setup. You can also choose to restore the
original Setup defaults that will return the Setup to its original state, and erase
any previous changes you have made in a previous session.
Figure 5 - 7
Exit Menu
5
Exit Menu 5 - 15
BIOS Utilities
5
5-16
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the
steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you
begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic wrist strap to ground yourself because static electricity may damage the
components.
The chapter includes:
• Removing the Primary Battery
• Upgrading the Hard Disk Drive(s)
• Upgrading the System Memory (RAM)
• Changing the Secondary Bay Device
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Upgrading The Computer
When Not to Upgrade
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and discon-
6
nected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
These procedures involve opening the system’s case, adding and sometimes
replacing parts.
You should not perform any of these upgrades if:
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase
or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
6 - 2 Overview
Upgrading The Computer
Removing the Primary Battery
If you are confident in undertaking upgrade procedures yourself, for safety
reasons it is best to remove the battery (batteries).
1. Turn the computer off, and turn it over.
2. Move the battery release latches in the direction of the arrows
3. The battery will pop -up.
4. Lift the battery out of the battery bay.
5. When re-inserting the battery, make sure that it is firmly pushed down into
the bay and the battery release latches click back into position.
3
1 2
3
1 2
- .
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
2nd Battery
If you have included
the secondary battery
in your purchase configuration, remember
to remove the secondary battery before undertaking any upgrade
procedures (see page
6 - 9).
Figure 6 - 1
Battery Removal
6
Removing the Primary Battery 6 - 3
Upgrading The Computer
HDD System
Warning
New HDD’s are blank.
Before you begin make
sure:
You have backed up any
data you want to keep
from your old HDD.
6
You have all the CDROMs and FDDs required to install your operating system and
programs.
If you have access to the
internet, download the latest application and hardware driver updates for
the operating system you
plan to install. Copy these
to a removable medium.
Figure 6 - 2
Hard Disk Cover
Removal
The hard disk drive(s) can be taken out to accommodate other 2.5" parallel
(PATA) or serial (SATA) hard disk drives with a height of 9.5mm (h) (see
“Storage Options” on page E - 3). Follow your operating system’s installa-
tion instructions, and install all necessary drivers and utilities (as outlined
in“Drivers & Utilities” on page 4 - 1), when setting up a new hard disk.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screws
3. Remove the bay cover .
1
2
4
3
1 3
- .
4
Upgrading the Hard Disk Drive(s)
6 - 4 Upgrading the Hard Disk Drive(s)
Loading...