EUROCOM 8500-V Owner's Manual
Notice
The company reserves the right to make any updates, revisions or changes to the
information contained herein as and when deemed necessary. The company is
under no obligation to notify any purchaser or end-user of such actions in advance
or afterwards.
2000
Trademarks
IBM PC, OS/2, PS/2, EGA, and VGA are registered trademarks of International Business Machines Corporation.
Intel, Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft Windows, Windows NT and Microsoft Mouse are registered
trademarks of Microsoft Corporation.
Sound Blaster Pro is a trademark of Creative Labs, Inc.
SystemSoft is a registered trademark of SystemSoft Corp.
Other brand and product names are trademarks of their respective companies.
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning:
[ A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is
essential that only the supplied power cord be used. ]
[ Use only shielded cables to connect I/O devices to this equipment. ]
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
[ ]: depend on EUT condition.
Safety Instructions
As with any other piece of precision electronic equipment, proper care and
operation of your notebook computer will prolong its use. Help your notebook
computer last longer by following this advice:
Handling the Computer
Do not expose it to excessive heat
or direct sunlight.
Do not expose it to strong magnetic
fields.
Do not expose your notebook
computer to any shock or vibration.
Do not leave it in a place where
foreign matter or moisture may
effect the system.
Do not place the computer on an
unstable surface.
Do not place the computer on any
surface which will block the vents.
Don’t use or store the computer in
a humid environment.
Do not turn off any peripheral devices when the computer power is
on
.
Do not disassemble the computer
by yourself.
Do not turn off the power until you
properly shutdown all programs.
Do not place anything heavy on
the computer.
When traveling by air, follow the
airline’s instructions for in-flight
use.
If there is an unusual odor, heat or
smoke coming from your computer, unplug the cord.
Perform routine maintenance on
your computer.
Handling of the Power Cord & Battery
Do not plug in the power cord if
you are wet.
Do not place heavy objects on the
power cord.
Keep the battery away from any
metal appliances.
Do not use the power cord if it is
broken.
Do not touch the battery contacts
with your hands or any metal objects.
Affix tape to the battery contacts
before disposing of the battery.
Handling Peripheral Devices
Use only approved brands of peripheral devices.
Other reminders
Do not throw the computer or accessories into a fire.
Remember to periodically save
your data. Data may be lost if the
battery is depleted.
Unplug the power cord before attaching any peripheral devices.
Do not touch the poisonous liquid if the LCD panel breaks.
Take periodic breaks if you are
using the computer for long periods of time.
Developing Good Work Habits
Developing good work habits are important if you need to work in front of the
computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
The following are some tips to reduce the strain:
! Adjust the height of the chair and/or desk so that the keyboard is at or
slightly below the level of your elbow. Keep your forearms, wrists, and
hands in a relaxed position.
! Y our knees should be slightly higher than your hips. Place your feet flat
on the floor or on a footrest if necessary .
! Use a chair with a back and adjust it to support your lower back comfort-
ably.
! Sit straight so that your knees, hips and elbows form approximately 90
degree angles when you are working.
Remember to:
! Alter your posture frequently .
! Stretch and exercise your body several times a day .
! T ake periodic breaks when you work at the computer for long periods of
time. Frequent and short breaks are better than fewer and longer breaks.
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain
and muscle fatigue in your neck and shoulders.
! Position the display to avoid glare or reflections from overhead lighting or
outside sources of light.
! Keep the display screen clean and set the brightness and contrast to
levels that allow you to see the screen clearly .
! Position the display directly in front of you at a comfortable viewing dis-
tance.
! Adjust the display viewing angle to find the best position.
Table of Contents
Chapter 1. Getting Started ................................................. 1-1
Checking the Items ...............................................................1-3
Opening the LCD Display .....................................................1-3
Top V iew with Display Open..................................................1-5
LCD Display................................................................................1-5
Power Button ..............................................................................1-5
Stereo Speakers .........................................................................1-5
T ouchpad and Buttons ................................................................1- 5
Keyboard ....................................................................................1-5
LED Indicators ............................................................................1-5
Microphone .................................................................................1-5
Right Side View.....................................................................1-7
Phone Jack.................................................................................1 -7
Hard Disk Drive ........................................................................... 1-7
PC Card Slot...............................................................................1-7
Floppy Disk Drive ........................................................................1- 7
Speaker-out Jack ........................................................................1-7
Audio Line-in Jack.......................................................................1- 7
Microphone Jack......................................................................... 1-7
Vent............................................................................................ 1-7
Right Side Stand.........................................................................1 -7
Rear View .............................................................................1-9
Power Jack .................................................................................1-9
Locking Device Connector........................................................... 1-9
Port Replicator Port ....................................................................1- 9
LAN Port..................................................................................... 1 -9
PS/2 Type Port ........................................................................... 1- 9
Parallel Port ................................................................................1- 9
S-video Jack ............................................................................. 1-11
RCA Jack ................................................................................. 1-11
Dual USB Ports ........................................................................ 1- 11
Serial Port................................................................................. 1-11
External Monitor (CRT) Port ...................................................... 1 - 1 1
1394 Port .................................................................................. 1-11
Left Side View .....................................................................1-12
Left Side Stand ......................................................................... 1-12
Infrared Port ..............................................................................1-12
CD-ROM Drive .......................................................................... 1-12
Chapter 2. Using the Computer.........................................2-1
The Power Sources ..............................................................2-3
AC Power Adapter ......................................................................2- 3
Battery Pack...............................................................................2-3
Turning on the Computer ......................................................2-5
LED Indicators ............................................................................2-5
The Hard Disk Drive (HDD) ..................................................2-7
Removing the HDD...................................................................... 2-7
Inserting the HDD........................................................................2-7
The Floppy Disk Drive (FDD)................................................2-9
Inserting/Removing Diskettes ......................................................2-9
The CD-ROM........................................................................2-9
Loading Compact Discs ..............................................................2-9
Handling Compact Discs........................................................... 2-11
The PC Card Slots.............................................................. 2-11
Inserting PC Cards.................................................................... 2 - 1 1
Removing PC Cards .................................................................. 2-11
The Hot Key ........................................................................2-13
The Numeric Keypad ..........................................................2-14
Chapter 3. Attaching Peripherals ......................................3-1
PS/2 Keyboard or Mouse ......................................................3-3
USB Compatible Device .......................................................3-3
Serial Mouse .........................................................................3-5
External Monitor (CRT) .........................................................3-5
TV Set ...................................................................................3-7
Parallel Printer.......................................................................3-7
Phone Line ............................................................................3-9
Security Lock ........................................................................3-9
Digital Camera .................................................................... 3-11
Video Input Device .............................................................. 3-1 1
Local Area Network (LAN)...................................................3-12
Chapter 4. Upgrading the Computer.................................4-1
Replacing the HDD ...............................................................4-3
Replacing the FDD ...............................................................4-3
Replacing the CD-ROM Module............................................4-5
Removing the CD-ROM ............................................................... 4-5
Inserting the CD-ROM module.....................................................4-5
Upgrading the Memory ..........................................................4-5
Installing a Memory Module ........................................................4- 7
Removing a Memory Module .......................................................4-9
Adding or Replacing the Processor ......................................4-9
Chapter 5. BIOS Utilities..................................................... 5-1
Power on Self Test (POST) ..................................................5-3
POST Message: Normal Operation ............................................. 5 -3
POST Message: Error Detected..................................................5-3
BIOS Setup Utility..................................................................5-5
Information in the BIOS Setup Utility ...........................................5-5
Initiating the BIOS Setup Utility...................................................5 - 5
Working with the Menu Bar .........................................................5- 7
Working with the Menu Items......................................................5-7
Features of BIOS Setup Utility ..............................................5-7
Main Menu..................................................................................5-7
Advanced Menu ........................................................................ 5-11
Security Menu ..........................................................................5-13
Power Menu.............................................................................. 5-15
Boot Menu ................................................................................ 5-17
Exit Menu ................................................................................. 5-17
Power Management............................................................5-19
Advanced Power Management (APM 1.2) .................................5-19
Advanced Configuration and Power Interface (ACPI) ..................5-19
Global Standby ......................................................................... 5-19
Hard Disk Standby.................................................................... 5-19
Suspend and Resume............................................................... 5-19
Chapter 6. Installing Drivers ..............................................6-1
Preparation for a New Notebook ...........................................6-3
Installing Windows 98 SE (For Reference Only) ..................6-3
Installing Windows 2000 (For Reference Only) ....................6-4
Before Installing Drivers ........................................................6-6
Installing Drivers in Windows 98 SE .....................................6-7
Step 1: Installing the VGA Driver.................................................6- 7
Step 2: Installing the Audio Driver................................................6- 7
Step 3: Installing the T ouchpad Driver..........................................6- 8
Step 4: Installing the Modem Driver.............................................6- 8
Step 5: Installing the LAN Driver..................................................6-9
Step 6: Installing the DVD driver (optional) ................................6-10
Installing Drivers in Windows 98 ME...................................6-12
Step 1: Installing the VGA Driver(A TI) ........................................ 6-12
Step 2: Installing the Audio Driver.............................................. 6-12
Step 3: Installing the T ouchpad Driver........................................ 6-13
Step 4: Installing the Modem Driver ...........................................6-14
Step 5: Installing the LAN Driver................................................ 6-15
Step 6: Installing the DVD driver (optional) ................................ 6-16
Installing Drivers in Windows 2000 .....................................6-18
Step 1: Installing the VGA Driver...............................................6-18
Step 2: Installing the Audio Driver.............................................. 6-18
Step 3: Installing the T ouchpad Driver........................................ 6-19
Step 4: Installing the Modem Driver ...........................................6-19
Step 5: Installing the LAN Driver................................................ 6-20
Step 6: Installing the DVD driver (optional) ................................ 6-21
Installing Drivers in Windows NT4.0 ...................................6-23
Step 1: Installing the VGA Driver...............................................6-23
Step 2: Installing the Audio Driver.............................................. 6-23
Step 3: Installing the T ouchpad Driver........................................ 6-24
Step 4: Installing the Modem Driver ...........................................6-24
Step 5: Installing the LAN Driver................................................ 6-25
Chapter 7. T roubleshooting...............................................7-1
Audio .....................................................................................7-3
Battery...................................................................................7-3
Boot Password ..................................................................... 7-5
CD ........................................................................................7-5
Floppy Disk Drive (FDD).......................................................7-5
Hard Disk Drive (HDD) .........................................................7-5
Hardware Installation.............................................................7-7
LCD Panel ............................................................................7-7
Memory Module.....................................................................7-7
PC Card................................................................................7-9
Power....................................................................................7-9
Printer ...................................................................................7-9
Appendix A. Specification................................................. A-1
Appendix B. Battery Information...................................... B-1
Appendix C. Different Versions of Keyboards................ C-1
Glossary ................................................................................. 1
Chapter 1. Getting Started
Chapter 1. Getting Started
This chapter provides you with the basic introduction about the computer and
its features. Now, lets take a look at the computer from the dif ferent view .
Checking the Items
Opening the LCD Display
T op View with Display Open
Right Side View
Rear View
Left Side View
1-1
User’s Manual
Checking the Items
Carefully remove everything from the shipping box and check the items one
by one. If any item is missing or damaged, contact your dealer immediately .
! Notebook Computer
! Carrying Bag
! Power Adapter
! Power Cord
! User’s Manual
! PS/2 Transfer Cable
! Utilities Diskette(s)
! Battery Pack
1-2
Chapter 1. Getting Started
Opening the LCD Display
1) Move the cover latch to the right to release the top cover (!).
2) Lift the top cover to reveal the LCD panel and keyboard (").
3) Adjust the LCD panel to a comfortable viewing angle.
4) Press the power button to power up the system.
1-3
User’s Manual
T op View with Display Open
LCD Display
The Notebook has a LCD (Liquid Crystal Display) panel. Depending
upon the model you have purchased, the display screen can be a
15.0" XGA or SXGA TFT color panel. The LCD panel is driven by a
AGP bus video controller with 8 or 16 MB video memory .
Power Button
Pressing this button turns your notebook computer on or off. Power
Button can also be used as a Suspend/Resume hot button when
pressed less than four seconds.
Note: After turning your notebook computer off, wait a few seconds
before turning it on again.
Stereo Speakers
1-4
Two built-in speakers provide rich, stereo sound.
Touchpad and Buttons
The pointing device features a sensitive glide pad for precise movements. It functions the same as a two-button mouse. The right
touchpad button is the same as a right mouse button; the left
touchpad button is the same as a left mouse button.
Keyboard
This 102-key keyboard has an embedded numeric keypad and can
be used with Windows 95 or Windows 98. It also has many of the
same features as a full-size desktop keyboard and can easily be
replaced with non-English keyboards.
Chapter 1. Getting Started
LED Indicators
These LED indicators display the system's operational status. Refer
to Chapter 2 LED Indicators for more information.
Microphone
With the built-in microphone you can record on your notebook
computer.
Microphone
Stereo Speakers
LCD Display
LED Indicators
Power Button
Keyboard
Touchpad and Button
1-5
User’s Manual
Right Side View
Phone Jack
The RJ-1 1 phone jack is used to support a built-in 56K MDC modem.
For more information on the phone jack please refer to Chapter 3
“Attaching Peripherals”.
Hard Disk Drive
The computer accepts any 2.5” hard disk drive with 9.5mm/12.7mm/
17.0mm height. The hard disk drive is removable and can be replaced. For more information please refer to Chapter 2 “Using the
Computer”.
PC Card Slot
There are two PC card slots (PCMCIA) located on the computer,
which accepts two Type II PC cards or one T ype III PC card to
expand the computer’s capability. To remove the PC card, press the
PC-Card eject button.
1-6
Floppy Disk Drive
The computer comes standard with a 1.44MB floppy disk drive
installed. The floppy-disk-drive module can be replaced with other
disk-drive units, such as a secondary 2.5” 12.7mm(h)/12.5mm(h)
hard disk drive or a 15mm(h) Zip 100/250MB drive. For more information please refer to Chapter 2 “Using the Computer”.
Chapter 1. Getting Started
Speaker-out Jack
Headphone and speakers can be attached to the system through this
jack.
Audio Line-in Jack
An external audio source can be connected to the computer through
this jack.
Microphone Jack
This jack is used to connect an external microphone. Besides, the
jack also provides a S/P-DIF (Sony/Philips Digital Interface Format)
output, which allows you to connect your DVD-capable PC to a
Dolby AC-3 compatible receiver. In that way , the digital audio data
from the DVD-ROM will be transported to the surround sound system
and offers you a spacious sound effect. To use the S/P-DIF output
function, you need to set the feature in the BIOS Setup Utility .
Vent
Prevents the notebook computer from overheating.
Right Side Stand
Position the stand (along with the left one) to adjust the angle of the
computer. If a high speed CPU is installed, erecting the stands on
both sides is necessary for heat dissipation during operation.
1-7
User’s Manual
Phone (RJ-11) Jack
Audio Line-in Jack
Speaker-out Jack
PC Card Slot
Hard Disk Drive
Pull down the stand when operating your computer.
Floppy Disk Drive
Microphone Jack
Right Side Stand
Vent
1-8
Rear View
Power Jack
Plug the AC adapter into this jack for power supply . To disconnect,
pull the adapter away from the jack.
Locking Device Connector
A lock for your computer can be attached to this slot to prevent
possible theft.
Port Replicator Port
Use this port to connect a port replicator to promote the computer’s
capability . A port replicator may come with a TV-out port or an
external diskette drive connector, etc.
LAN Port
Chapter 1. Getting Started
The LAN Port is used to connect your notebook to a local area
network.
PS/2 Type Port
The PS/2 Type Port uses a 6-pin connector for connecting an external
PS/2 type mouse or keyboard.
Parallel Port
The Parallel Port uses a 25-pin female connector for connecting a
parallel printer or other parallel devices. This parallel port supports
EPP(Enhanced Parallel Port) V1.7/V1.9 and ECP (Extended Capabilities Port) modes.
1-9
User’s Manual
S-video Jack
Use this jack to transmit a video signal to a TV set.
RCA Jack
This jack allows the computer to receive analog composite signals
from external video devices, e.g. camera, CD.
Dual USB Ports
The dual Universal Serial Bus (USB) ports make adding peripheral
devices easy .
Serial Port
The RS-232C serial port uses a 9-pin male connector for connecting an
external serial mouse, serial printer or fax/modem.
1-10
External Monitor (CRT) Port
The External Monitor port uses a 15-pin connector for connecting an
external CRT monitor . Simultaneous display on the LCD screen and
external CRT monitor is possible.
1394 Port
The 1394 Port is used to connect a digital camera.
Chapter 1. Getting Started
Power Jack
Locking Device Connector
Port Replicator
Open the back cover to reveal the ports as shown below.
S-Video Jack
RCA Jack
Parallel Port
Dual USB Ports
Serial Port
PS/2 Port
LAN Port
External Monitor Port
1394 Port
1-11
User’s Manual
Left Side View
Left Side Stand
Position the stand (along with the right one) to adjust the angle of the
computer. If a high speed CPU is installed in the computer , erect the
stands on both sides to help heat dissipation during operation.
Infrared Port
This port allows communication with an infrared-compatible device.
The Infrared port supports IrDA (HPSIR) 1.1 mode, Amplitude Shifted
Keyed IR (ASKIR) mode, and Fast IR (FIR) mode. For further information, please refer to the manual of the wireless device you wish to
connect.
CD-ROM Drive
The notebook comes standard with a 24X speed, 5.25” CD-ROM
drive. The removable CD-ROM drive module can be replaced with an
optional DVD-ROM or CD-RW .
1-12
Left Side Stand
Infrared Port
CD-ROM Drive
Chapter 2. Using the Computer
Chapter 2. Using the Computer
Y our notebook computer can be used almost anywhere, in the home, office, or
on the road. T o learn more about how to operate your computer, the features
available and how to power your computer please read this chapter.
The Power Sources
Turning on the Computer
The Hard Disk Drive
The Floppy Disk Drive
The CD-ROM
The PC Card Slots
The Hot Key
The Numeric Keypad
2-1
User’s Manual
The Power Sources
The computer can be powered by either an AC adapter or a battery pack depending on where you want to use it.
AC Power Adapter
Use only the power adapter that comes with your computer. An incorrect type
of power adapter will damage the computer and its components.
1) Plug the power adapter cord into the power jack on the rear panel of
the computer.
2) Connect the power adapter with the power cord.
3) Plug the power cord into a properly grounded outlet.
2-2
Chapter 2. Using the Computer
Battery Pack
The battery pack allows you to use your notebook computer when you are on
the road or an electrical outlet is unavailable. Battery life differs depending on
the applications and the configuration you're using.
Inserting the Battery Pack
1) Turn the computer over.
2) Firmly fit the battery pack into the place at a slight angle.
3) Install the four screws to fasthen the battery pack.
Removing the Battery Pack
1) Turn the computer over.
2) Remove the four screws.
3) Carefully lift the battery pack out of the computer.
Note: To increase battery life, let the battery discharge completely before
recharging.
2-3
User’s Manual
Recharging by AC Power
The battery pack will automatically recharge when it is in its bay in the computer and the computer is plugged into an AC power supply .
While the battery is recharging, you can still use the computer.
It will take several hours to fully recharge the battery and slightly longer if you
are using the computer while the battery is recharging.
(Please refer to LED Indicators in this chapter for more information on the battery charge status.)
Proper Handling of the Battery Pack
Do not disassemble the battery pack under any circumstances.
Do not expose the battery to fire or high temperatures, it may explode.
Do not connect the metal terminals (+, -) together.
2-4
Chapter 2. Using the Computer
Turning on the Computer
Now you are ready to begin using your new notebook computer. To turn it on
simply press the power button.
Power Button
Note: After turning off the computer, wait for a few seconds before you turn it on
again.
LED Indicators
The LED indicators on the computer indicate the system’s operation status.
The indicators are located on two locations: on the top cover and the front
panel. Please refer to the next page for the function of each indicator.
2-5
Loading...