Notice
The company reserves the right to make any updates, revisions or
changes to the information contained herein as and when deemed
necessary. The company is under no obligation to notify any
purchaser or end-user of such actions in advance or afterwards.
September , 2000
Trademarks
IBM PC, PS/2, XGA, and SVGA are registered trademarks of
International Business Machines Corporation.
Intel, Pentium are trademarks of Intel Corporation.
SiS is a registered trademark of Silicon Integrated Systems.
MS-DOS, Microsoft Windows, Windows 98, Windows 2000, Windows NT and Microsoft Mouse are registered trademarks of
Microsoft Corporation.
Insyde is a registered trademark of SystemSoft Corp.
Other brand and product names are trademarks of their respective companies.
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Warning:
[ A shielded-type power cord is required in order to meet FCC emission
limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used. ]
[ Use only shielded cables to connect I/O devices to this equipment. ]
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate
the equipment.
[ ]: depend on EUT condition.
Safety Instructions
As with any other piece of precision electronic equipment,
proper care and operation of your notebook computer will prolong its use. Help your notebook computer last longer by following this advice:
Handling the Computer
Do not expose it to excessive heat
or direct sunlight.
Do not expose it to strong magnetic
fields.
Do not expose your notebook
computer to any shock or vibration.
Do not leave it in a place where
foreign matter or moisture may
effect the system.
Do not place the computer on an
unstable surface.
Do not place the computer on any
surface which will block the vents.
Don’t use or store the computer in
a humid environment.
Do not turn off any peripheral devices when the computer is on
.
Do not disassemble the computer
by yourself.
Do not turn off the power until you
properly shutdown all programs.
Do not place anything heavy on
the computer.
When traveling by air, follow the
airline’s instructions for in-flight
use.
If there is an unusual odor, heat or
smoke coming from your computer, unplug the cord.
Perform routine maintenance on
your computer.
Handling of the Power Cord & Battery
Do not plug in the power cord if
you are wet.
Do not place heavy objects on the
power cord.
Keep the battery away from any
metal appliances.
Do not use the power cord if it is
broken.
Do not touch the battery contacts
with your hands or any metal objects.
Affix tape to the battery contacts
before disposing of the battery.
Handling of Peripheral Devices
Use only approved brands of peripheral devices.
Other reminders
Do not throw the computer or accessories into a fire.
Remember to periodically save
your data. Data may be lost if the
battery is depleted.
Unplug the power cord before attaching any peripheral devices.
Do not touch the poisonous liquid if the LCD panel breaks.
Take periodic breaks if you are
using the computer for long periods of time.
Developing Good Work Habits
Developing good work habits are important if you need to work in
front of the computer for long periods of time. Improper work
habits can result in discomfort or serious injury from repetitive
strain to your hands, wrists or other joints. The following tips
should help reduce the strain:
– Adjust the height of the chair and/or desk so that the
keyboard is at or slightly below the level of your elbow.
Keep your forearms, wrists, and hands in a relaxed
position.
– Your knees should be slightly higher than your hips.
Place your feet flat on the floor or on a footrest if
necessary.
– Use a chair with a back and adjust it to support your
lower back comfortably.
– Sit straight so that your knees, hips and elbows form
approximately 90 degree angles when you are working.
Remember to:
– Alter your posture frequently.
– Stretch and exercise your body several times a day.
– Take periodic breaks when you work at the computer for
long periods of time. Frequent and short breaks are
better than fewer and longer breaks.
Lighting
Proper lighting and comfortable display viewing angle can reduce
eye strain and muscle fatigue in your neck and shoulders.
– Position the display to avoid glare or reflections from
overhead lighting or outside sources of light.
– Keep the display screen clean and set the brightness and
contrast to levels that allow you to see the screen clearly.
– Position the display directly in front of you at a
comfortable viewing distance.
– Adjust the display viewing angle to find the best position.
Table of Contents
Chapter 1: Getting Started ...............................1- 1
Checking the Items .............................................. 1-2
Opening the LCD display....................................... 1-3
Top View with Display Open ................................... 1-4
Right Side View ................................................... 1-6
Rear View..........................................................1-8
Left Side View................................................... 1-10
Bottom View ..................................................... 1-12
Chapter 2: Using the Computer ......................... 2 - 1
The Power Sources.............................................. 2-2
Battery Pack....................................................... 2-3
Removing the battery pack ............................................2-3
Inserting the battery pack ..............................................2-3
Recharging by AC Power ............................................... 2-4
Proper Handling of the Battery Pack ................................ 2-5
Turning on the Computer....................................... 2-5
LED Power Indicators ....................................................2-6
LED Status Indicators....................................................2-7
The Hard Disk Drive (HDD)..................................... 2-8
The Floppy Disk Drive (FDD)................................... 2-9
The DVD-ROM Drive.......................................... 2-10
The PC Card Slots ............................................. 2-12
Hot Keys ......................................................... 2-13
The Numeric Keypad .......................................... 2-14
Chapter 3: Adding Peripherals.......................... 3 -1
PS/2 Keyboard or Mouse ...................................... 3-2
USB Compatible Device ........................................ 3-3
Serial Mouse ...................................................... 3-4
External Monitor (CRT) .......................................... 3-5
Parallel Printer..................................................... 3-6
Internal Modem ................................................... 3-7
LAN port............................................................ 3-8
Security Lock...................................................... 3-9
Chapter 4: Upgrading the Computer .................4 -1
Replacing the HDD .............................................. 4-2
Replacing the FDD............................................... 4-3
Replacing the DVD-ROM Module ............................ 4-5
Upgrading the Memory.......................................... 4-6
Adding or replacing the processor.......................... 4-11
Chapter 5: BIOS Utilities .................................. 5 -1
Power on Self Test (POST)..................................... 5-2
System Configuration Utility .................................... 5-4
Working with the Pull-down Menu (Submenu)............. 5-6
Working with the Menu Bar..................................... 5-6
Features of the SCU............................................. 5-8
Power Management ........................................... 5-19
Chapter 6: Installing Drivers ............................ 6-1
Preparation for a New Notebook.............................. 6-2
Installing Windows 98 SE (For Reference Only) ........... 6-3
PC Card Problem in Windows 98 ...................................... 6 -4
Installing Windows 2000 (For Reference Only) ............ 6-5
Installing Drivers in Windows 98 SE .......................... 6-6
Installing Drivers in Windows 2000 ......................... 6-10
Installing Drivers in Windows NT4.0 ........................ 6-14
Chapter 7: Troubleshooting .............................. 7- 1
Audio................................................................ 7-2
Battery .............................................................. 7-2
Boot Password.................................................... 7-4
CD-ROM/DVD-ROM ............................................ 7-4
Floppy Disk Drive (FDD) ........................................ 7-5
Hard Disk Drive (HDD) .......................................... 7-6
Hardware Installation ............................................ 7-6
LCD Panel ......................................................... 7-7
Memory Module .................................................. 7-7
PC Card ............................................................ 7-8
Power............................................................... 7-8
Printer............................................................... 7-9
Appendix ............................................................i
A. Specifications...................................................... i
B: Battery Information .............................................. iv
C: Different Keyboards .............................................vi
Glossary............................................................1
Chapter 1: Getting Started
Chapter 1: Getting Started
Lets take a closer look at your new notebook computer.
This chapter will cover the following areas:
- Checking the Items
- Opening the LCD Display
- Top View with Display Open
- Right Side View
- Rear View
- Left Side View
- Bottom View
1-1
User’s Manual
Checking the Items
Carefully remove everything from the shipping box and check the
items one by one. If any item is missing or damaged, contact your
dealer immediately.
!
"
You should have:
1. Notebook Computer
#
$
2. User’s Manual
3. CD-ROM
4. Power Adapter
%
&
'
5. PS/2 Transfer Cable
6. Utilities Diskette(s)
7. Power Cord
(
)
8. Carry Bag
9. Battery Pack
1-2
Chapter 1: Getting Started
Opening the LCD display
1) Move the cover latch to the right to release the top cover.
2) Lift the top cover to reveal the LCD panel and keyboard.
3) Adjust the LCD panel to a comfortable viewing angle.
1-3
User’s Manual
Top View with Display Open
LCD Display
The Notebook has a 12.1" SVGA/XGA TFT LCD (Liquid
Crystal Display) panel which supports up to a 800 × 600
× 32 bit resolution. The LCD panel is driven by an AGP
bus video controller with 8~32 MB video memory.
LED Power Indicators
These indicators display the current power source of
the computer. For more information please refer to
Chapter 2 LED power indicators.
LED Status Indicators
These LED indicators display the system's operational
status. Refer to Chapter 2 LED status indicators for
more information.
1-4
Stereo Speakers
Two built-in speakers provide rich, stereo sound.
Trackpad and Buttons
The pointing device features a sensitive glide pad for
precise movements. It functions the same as a twobutton mouse. The right trackpad button is the same as
a right mouse button; the left trackpad button is the
same as a left mouse button.
Chapter 1: Getting Started
Keyboard
This 88 key keyboard has an embedded numeric keypad
and can be used with Win95, Win98, Windows 2000,
Windows NT 4.0 and Linux. It also has many of the
same features as a full-size desktop keyboard and can
easily be replaced with non-English keyboards.
Microphone
With the built-in microphone you can record on your
notebook computer.
LCD Display
Microphone
Keyboard
Trackpad and Buttons
LED Power Indicators
LED Status Indicators
Stereo Speakers
1-5
User’s Manual
Right Side View
Power Button
Pressing this button turns your notebook computer on or off.
After proper configuration with the System Configuration Utility
(SCU), the Power Button can also be used as a Suspend/Resume
hot button.
Note: After turning your notebook computer off, wait a few
seconds before turning it on again.
Easy to change 5.25" DVD-ROM Drive
The notebook comes standard with a 8 speed DVD-ROM drive.
The removable DVD-ROM drive module can be replaced with
optional drive units, such as a 12.7 mm high 5.25" CD-ROM drive.
(Please refer to the chapter 2 for more information on using the
DVD-ROM or Chapter 4 for removing or replacing the DVDROM.)
LED Status Indicators
These LED indicators display the system's operational status.
Refer to Chapter 2 LED status indicators for more information.
Vent
Prevents the notebook from overheating.
1-6
LED Status Indicators
Chapter 1: Getting Started
Power Button
5.25" DVD-ROM Drive
Vent
1-7
User’s Manual
Rear View
PS/2 Type Port
The PS/2 Type Port uses a 6 pin connector for connecting an external PS/2 type mouse or keyboard.
USB Port
The Universal Serial Bus (USB) port makes adding
peripheral devices easy.
External Monitor (CRT) Port
The External Monitor uses a 15 pin connector for connecting an external CRT monitor. Simultaneous display
on the LCD screen and external CRT monitor is possible.
1-8
Parallel Port
The Parallel Port uses a 25 pin female connector for
connecting a parallel printer or other parallel devices.
This parallel port supports EPP (Enhanced Parallel
Port) V1.7/V1.9 and ECP (Extended Capabilities Port)
modes.
Serial Port
The RS-232 serial port uses a 9 pin male connector for
connecting an external serial mouse or serial printer.
Chapter 1: Getting Started
Lan Port
Use this port to connect your notebook computer to a
Local Area Network
Phone Jack
The phone jack is used to support an optional internal
modem. If you do not intend to install this optional
modem, please do not punch out the phone jack. For
more information on the phone jack please refer to
Chapter 3.
AC-in Socket
Plug the AC adapter into this socket to connect to an
external power supply. To disconnect, pull the plug (not
the cord) directly back.
USB Port
PS/2 Type Port
External Monitor (CRT) Port
Parallel Port
AC-in Socket
Lan Port
Serial Port
Phone Jack
1-9
User’s Manual
Left Side View
Security Slot
A lock for your computer can be attached to this slot to
prevent possible theft.
Microphone-in Jack
A microphone can be connected to your notebook with
this jack.
Speaker-out Jack
Headphone and speakers can be attached to the system
through this jack.
Infrared Port
This port allows communication with an infraredcompatible device. The Infrared port supports Amplitude Shifted Keyed IR (ASKIR) mode. For further
information, please refer to the manual of the wireless
device you wish to connect.
1-10
Volume Control knob
Adjust the audio output with this dial.
3.5" Floppy Disk Drive (FDD)
The drive is a 3.5", 3 mode, 1.44 MB easy to change
floppy disk drive.
Chapter 1: Getting Started
PC Card Socket
The notebook provides one Type II PC card socket. This
socket supports CardBus.
Security Slot
Speaker-out Jack
Microphone-in Jack
Volume Control knob
PC Card Socket
Infrared Port
3.5" Floppy Disk Drive (FDD)
1-11
User’s Manual
Bottom View
Heat Sink and CPU Cover
The CPU and Heat Sink are under this cover. To upgrade the
CPU you must remove this cover and remove the Heat Sink. For
further details please refer to Chapter 4.
DVD / FDD Cover
The connecting cables of the DVD/CD-ROM drive and FDD are
located beneath this cover. For more information on removing the
drives please refer to Chapter 4.
Battery Pack Latch
This latch secures the battery pack in its bay. (Please refer to
Chapter 2 for more information on inserting or removing the
Battery pack.)
FDD Tab
After you have disconnected the FDD from the computer, pull on
this tab to release the Floppy Disk Drive module from its bay.
(Please refer to Chapter 4 for more information on inserting or
removing the Floppy Disk Drive.)
HDD latch
This latch secures the Hard Disk Drive (HDD) module in its bay.
(Please refer to Chapter 2 for more information on inserting or
removing the Hard Disk Drive.)
1-12
Heat Sink and CPU Cover
Chapter 1: Getting Started
DVD / FDD Cover
Battery Pack
HDD latch
FDD Tab
Battery Pack Latch
1-13
Chapter 2: Using the Computer
Chapter 2: Using the Computer
Your notebook computer can be used almost anywhere, in the
home, office, or on the road. To learn more about how to operate
your computer, the features available and how to power your
computer please read this chapter.
The topics covered in this chapter are:
- The Power Sources
- Battery Pack
- Turning on the Computer
- LED indicators
- The Hard Disk Drive
- The Floppy Disk Drive
- The DVD/CD-ROM
- The PC Card Sockets
- Hot Keys
- The Numeric Keypad
2-1
User’s Manual
The Power Sources
The computer can be powered by either an AC adapter or battery
pack depending on where you want to use it.
AC Power Adapter
Use only the power adapter that comes with your computer. An
incorrect type of power adapter will damage the computer and its
components.
1) Plug the power adapter cord into the AC-in socket on the
rear panel of the computer.
2) Connect the power adapter with the power cord.
3) Plug the power cord into a properly grounded outlet.
2-2
Chapter 2: Using the Computer
Battery Pack
The battery pack allows you to use your notebook computer when
you are on the road or an electrical outlet is unavailable. Battery
life depends on the application and the configuration
you're using.
Removing the battery pack
1) Turn the computer
over.
2) Slide the latch in the
direction indicated
.
3) Gently grasp the
battery pack on the
edge below the
latches and lift it out
of the bay
Inserting the battery pack
1) Turn the computer over.
2) Place the battery in its bay inserting the side without the
latch in first.
3) Push down on the side with the latch until it clicks into
place.
Note: To increase battery life, let the battery discharge completely before recharging.
.
2-3
User’s Manual
Recharging by AC Power
The battery pack will automatically recharge when it is in its bay
in the computer and the computer is plugged into an AC power
supply.
While the battery is recharging, you can still use the computer.
It will take several hours to fully recharge the battery and
slightly longer if you are using the computer while the battery is
recharging.
(Please refer to LED power indicators in this chapter for more
information on the battery charge status.)
Note:
– The battery indicator light
will blink when the battery
overheats or there is a problem with the battery. Should this
happen, remove the battery and allow it to cool down. If the
indicator light still blinks contact your vendor about a possible
battery problem.
– The battery has protection design to detect the temperature while recharging or discharging. To ensure the battery can
be recharged, while discharging wait until the battery returns to
normal temperature, then recharge the battery
– For better battery life:
1) Fully discharge the battery before recharging.
2) Recharge the battery to full capacity each time you
recharge it.
2-4
Chapter 2: Using the Computer
Proper Handling of the Battery Pack
Do not disassemble the battery pack under any
circumstances.
Do not expose the battery to fire or high temperatures, it
may explode.
Do not connect the metal terminals (+, -) together.
Turning on the Computer
Now you are ready to begin using your new notebook computer.
To turn it on simply press the power button on the right side of
the computer.
After proper configuration with the System Configuration Utility
(SCU), the Power Button can also be used as a Suspend/Resume
hot button (Please refer to Chapter 5, BIOS Utilities, Power
Menu for more information.)
2-5
User’s Manual
LED Indicators
To display useful information there are two sets of LED indicators on your computer, they are the LED Power Indicators and
LED Status Indicators.
LED Power Indicators
The LED power indicators located on the top
right side display the
power status.
2-6
Icon Color Description
Green Battery power is being used
Red AC power is being used while
Blinking Red Battery power is critically low.
Green Battery is fully charged.
Red Battery is being charged.
while the computer is on.
the computer is on.
Chapter 2: Using the Computer
LED Status Indicators
Once your computer is on and in use the LED status indicators
will display the system's operating status.
Icon Color Description
Green The system has entered the
configured suspend mode.
Green The hard disk is being accessed
Green Num lock is activated
Green Cap Lock is activated .
Green Scroll Lock is activated.
2-7
User’s Manual
The Hard Disk Drive (HDD)
The hard disk drive is used to store your data internally in the
notebook computer. It is mounted in a removable case and can be
taken out to accommodate other 2.5" IDE hard disk drives with a
height of 12.7 mm or 9.5 mm. The system supports PIO mode 4,
Master mode IDE, LBA mode and provides a high performance
data transfer rate at speeds up to 66 MBytes/second (ATA-66).
For data security you can easily remove the HDD.
Removing the HDD
1) Turn the computer off.
2) Turn the computer over.
3) Locate the HDD latch .
4) Slide and hold the latch forward then slide the HDD out of
the computer.
5) Lift the hard disk drive out of
the computer.
Inserting the HDD
1) Turn off the computer.
2) Turn the computer over.
3) Place the HDD case into the computer.
4) Slide the HDD in until you hear a click.
2-8
Chapter 2: Using the Computer
The Floppy Disk Drive (FDD)
The computer is equipped with a 1.44 MB, 3.5" floppy disk drive
module. It is usually designated drive A by default and can be
used as a boot device if properly set in the SCU (please refer to
Chapter 5, BIOS Utilities).
Inserting/Removing Diskettes
When using the floppy drive, always insert your floppy diskette
label-side up. To remove your diskette, press the eject button on
the top-right corner of the floppy drive.
2-9
User’s Manual
The DVD-ROM Drive
The notebook computer comes standard with a 8x speed removable 5.25" DVD-ROM drive. It is labeled drive D and may be used
as a boot device if properly set in the System Configuration Utility. The removable DVD-ROM drive can be replaced with optional drive units, such as a 12.7 mm high CD-ROM drive.
Loading Disks
To insert a disk, press the Open Button and carefully place a disk
into the Disk tray with label-side facing up (see below). Push the
disk tray in and you are ready to start. The Access Indicator will
light up while data is being accessed or while an audio disk is
playing. When power is unexpectedly interrupted, insert an
object such as a straightened paper clip into the Emergency Eject
hole to open the tray.
Emergency Eject hole
Access indicator
Open Button
Note: When manually ejecting a disk, DO NOT use a sharpened
pencil or similar object that may break and become lodged in the
hole.
2-10
Chapter 2: Using the Computer
Handling Disks
Proper handling of your disks will prevent them from being
damaged. Please follow the advice listed below to make sure that
the data stored on your CD/DVD-ROMs can be accessed.
Remember to:
– Hold the disk by the edges; do not touch the surface of the
disk.
– Use a clean, soft, dry cloth to remove dust or fingerprints.
– Do not write on the surface with a pen.
– Do not attach paper or other materials to the surface of the
disk.
– Do not store or place the disk in high-temperature areas.
– Do not use benzene, thinners, or other cleaners to clean the
disk.
– Do not bend the disk.
– Do not drop or subject the disk to shock.
2-11
User’s Manual
The PC Card Slots
The computer is equipped with one PC card slot (previously
referred to as PCMCIA). The slot supports one Type II PC card or
CardBus card.
Inserting PC Cards
Align the PC card with the slot and push the card in until it is
firmly in place.
Removing PC Cards
To remove a PC card, simply press the eject button next to the
slot.
eject button
2-12
Chapter 2: Using the Computer
Fn + F3 Expand LCD display
Fn + F5 Toggle audio on/off
Fn + F6 Toggle between CRT / LCD / LCD+CRT
Fn + F9 Decrease LCD brightness
Fn + F10 Increase LCD brightness
Fn + Esc Suspend/resume
Hot Keys
Hot Keys allow you to change operational features instantly. You
activate the Hot Key functions by pressing the Fn key or Function
key which is located on the bottom-left of the keyboard and one of
the keys with the blue icons (F3, F6, etc....) located at the top of
your keyboard.
Function key
Available Hot Key commands
2-13
User’s Manual
The Numeric Keypad
A numeric keypad is integrated into the keyboard for easy numeric data input. The keypad stands out by its blue typeface.
To use the keypad simply:
1) Activate the Num Lock feature (press the Num Lock key).
2) Press and hold down the Fn key.
3) Press the desired number keys.
2-14
Chapter 3: Attaching Peripherals
Chapter 3: Adding Peripherals
To enhance your computer's capabilities, you can attach peripheral devices to the computer using the ports or jacks located on
the rear and left side of the computer.
The computer can support the following peripheral devices and
this chapter will explain how to connect them to your notebook:
- PS/2 Keyboard or Mouse
- USB Compatible Device
- Serial Mouse
- External Monitor (CRT)
- Parallel Printer
- Modem
- LAN port
- Security Lock
3-1
User’s Manual
PS/2 Keyboard or Mouse
The computer can use a PS/2 keyboard or mouse attached directly
to the PS/2 port or if you want you can attach both using the PS/2
transfer cable that comes with your notebook computer. Attach
the external keyboard or mouse to the PS/2 port as shown below.
3-2
Chapter 3: Attaching Peripherals
USB Compatible Device
The computer has a USB port for connecting a USB compatible
keyboard, mouse, game pad or other USB device. Simply plug the
device into the USB port as shown below.
3-3
User’s Manual
Serial Mouse
The serial port features a 9 pin connector. You can connect any
serial device such as a mouse to this port.
To connect a serial device you must:
1) Turn off the computer.
2) Connect the cable to the serial port on the rear of the
computer
3) Tighten the screws that fasten the cable to the serial
port
4) Turn on the computer.
.
.
Note: In addition, you may need to install the manufacturersupplied driver for the serial mouse. Refer to the device's user
guide for more information.
3-4
Chapter 3: Attaching Peripherals
External Monitor (CRT)
The computer can support an XGA compatible external monitor.
The external monitor can be used simultaneously with the LCD
display turned on or off. You can setup your computer to use an
external monitor by entering the System Configuration Utility
(SCU) and selecting the appropriate parameters or using the Fn +
F6 keys (refer to Hot Keys in Chapter 2).
To install an external monitor you simply:
1) Turn off the computer.
2) Connect the cable to the CRT port on the rear of the
computer
3) Tighten the screws that fasten the cable to the CRT
4) Insert the other end of the cable to the external monitor.
5) Turn on the computer.
.
.
3-5
User’s Manual
Parallel Printer
You can connect any standard Centronics parallel printer to your
computer using the parallel port.
To connect a printer simply:
1) Turn off the computer.
2) Connect the cable to the parallel port on the rear of the
computer
3) Tighten the screws that fasten the cable to the parallel port
.
4) Insert the other end of the cable to the printer's connector.
5) Fasten the cable's connector.
6) Turn on the printer and computer.
Note: You may also need to install the manufacturer-supplied
driver for the printer. Refer to the device’s user guide for more
information. If the connected printer supports Enhanced Parallel Port (EPP) or Extended Capabilities Port (ECP) mode,
please enter the System Configuration Utility (SCU) to configure the required setting.
.
3-6
Chapter 3: Attaching Peripherals
Internal Modem
The notebook has a phone jack (RJ-11) for connecting to a phone
line. To connect your computer’s internal modem to a phone line,
simply plug a phone cord into the phone jack.
phone jack
3-7
User’s Manual
LAN port
(RJ-45)
The notebook has a LAN port for connecting to a LAN (Local Area
Network). To connect to a LAN, simply plug the LAN line into the
port.
LAN port
3-8
Chapter 3: Attaching Peripherals
Security Lock
A security lock can be installed on your notebook computer to
help prevent theft. To install the security lock, wrap the cable
around a desk or other immovable object, then insert the locking
device in the slot located on the left side of your notebook computer.
3-9
Chapter 4: Upgrading the Computer
Chapter 4: Upgrading the Computer
This chapter will explain how to upgrade your notebook computer. Please follow the steps in this chapter and if you have any
problems or questions, you can contact your dealer for further
help.
Before you upgrade the computer, you will need:
- A small crosshead or Philips screwdriver
- A small regular screw driver.
- An antistatic wrist strap
Note: Make sure you wear an antistatic wrist strap to ground
yourself before working with or repairing the internal components. Static electricity may damage the components.
This chapter will cover the following topics:
- Replacing the HDD
- Replacing the FDD
- Replacing the DVD-ROM Module
- Upgrading the Memory
- Adding or replacing the processor
4-1
User’s Manual
Replacing the HDD
1) Remove the HDD case from the computer (refer to
Removing the HDD in Chapter 2 for details).
2) Remove the two sets of screws on the side of the case.
3) Slowly remove the HDD from the case until you see the
connecting cable.
4) Gently disconnect the cable from the HDD being careful
not to bend any pins or crimp the cable.
5) Connect a new HDD to the cable being careful not to
bend any pins or crimp the cable.
6) Slowly place the HDD back into the case.
7) Hold the HDD firmly in place with two screws on each
side.
8) Insert the HDD into the computer (refer to Inserting
the HDD in Chapter 2 for details)
4-2
fastening screws
fastening screws
Replacing the FDD
Removing the Floppy Disk Drive
1) Turn off the computer.
2) Turn the computer over.
Chapter 4: Upgrading the Computer
3) Locate the DVD / FDD cover
4) Unscrew and remove the cover .
5) Lift the white plastic piece which holds the FDD cable in
place
6) Pull out the FDD cable
7) Grasp the FDD tab and gently PULL the FDD out of the
computer
.
.
.
.
4-3
User’s Manual
8) Remove the two screws on each side of the FDD tray.
9) Remove the FDD from its tray. (see picture)
fastening screws
fastening screws
The FDD floppy disk drive out of its bay
Inserting the Floppy Disk Drive
Follow the instructions for removing the FDD in reverse order.
4-4
Chapter 4: Upgrading the Computer
Replacing the DVD-ROM Module
Removing the DVD-ROM Module
1) Turn off the computer.
2) Turn the computer over.
3) Locate the DVD/FDD cover
4) Unscrew and remove the cover.
5) Remove the single screw which holds the DVD-ROM in the
computer
6) Locate the cable tab and gently pull the cable tab upward to
disconnect the DVD-ROM from the computer mainboard
.
7) Grasp the DVD-ROM tab
and gently PULL the
DVD-ROM out of the
computer
.
.
.
Inserting the DVD-ROM module
Refer to removing the DVD-ROM and follow the instructions in
reverse order.
4-5
User’s Manual
Upgrading the Memory
The computer has two memory sockets for PC-100/PC-133 compliant, 144 pin SODIMM (Small Outline Dual In-line Memory Module) modules. The memory can be expanded to 512 MB with the
following combinations:
Bank 0
(64-bit)
32 MB Empty 32 MB
32 MB 32 MB 64 MB
64 MB Empty 64 MB
64 MB 32 MB 96 MB
64 MB 64 MB 128 MB
128 MB Empty 128 MB
128 MB 32 MB 160 MB
128 MB 64 MB 192 MB
128 MB 128 MB 256 MB
256 MB Empty 256 MB
256 MB 32 MB 288 MB
256 MB 64 MB 320 MB
256 MB 128 MB 384 MB
256 MB 256 MB
Once a new module is installed the memory size is automatically
detected by the POST routines when you turn on your computer.
Bank 1
(64-bit)
Power Total
Size
3.3V
512 MB
4-6
Chapter 4: Upgrading the Computer
Installing a Memory Module
1) Turn off the computer.
2) Press the two keyboard
latches at the top of the
keyboard to elevate the
keyboard from its normal
position.
3) Carefully lift the keyboard assembly out to
expose the mainboard.
Figure 4-1
4) Locate the memory banks, Bank 0 is on the right and Bank 1
is on the left.
Note: Only use Bank 0 if you have one memory module. If you are
using two memory modules always use the larger module in Bank
0.
Bank 1 Bank 0
Figure 4-2
4-7
User’s Manual
5) Insert the memory
module at an angle (about
45°) and fit its connectors
firmly into the bank
.
6) Press down the edge of
the memory module and
lock it into place
.
7) Put the keyboard back
into place.
Note: Make sure the connectors go into the bank. You must use
a RAM module that complies with Intel unbuffered SODIMM
(67.6 mm x 29.0 mm). Please consult your dealer for the details.
67.6 mm
4-8
29.0 mm
connectors
Chapter 4: Upgrading the Computer
Changing the S3 DIP Switch settings
Once you have installed the new memory you will have to
change the DIP Switch settings depending on the type of
memory you have installed. Please refer to the chart below for
the correct settings for the S3 DIP Switches
SDRAM
TYPE
S3-1 S3-2 S3-3 S3-4
PC100 ON OFF OFF OFF
PC133 ON OFF ON OFF
S3 DIP Switch
ON position
OFF position
4-9
User’s Manual
Removing a Memory Module
1) Turn off the computer.
2) Press the two keyboard latches to elevate the keyboard
from its normal position (refer to page 4-7, Figure 4-1)
3) Carefully lift the keyboard assembly out to expose the
mainboard.
4) Locate the memory sockets. Bank 0 is on the left and
Bank 1 is on the right. (refer to page 4-7, Figure 4-2)
5) Gently pull the two latches outward on both ends of the
module .
6) The module will pop up
.
7) Remove the memory module .
8) Install a new memory module if desired (refer to
Installing a Memory Module).
9) Put the keyboard back into place.
4-10
Chapter 4: Upgrading the Computer
Adding or replacing the processor.
Note: If you plan on removing the heat sink, which is necessary
to add or replace the processor, you will need to have a replacement heat sink pad available. Before proceeding, please contact
your dealer to get a replacement pad which you will need when
you reinstall the heat sink.
In order to add or replace the processor you must:
A: Remove the heat sink
B: Remove the processor
C: Insert a new processor
D: Reinstall the heat sink
E: Changing the SW1 DIP Switch settings
A: Remove the heat sink
1) Turn off the
computer
2) Turn over the
computer
3) Remove the Heat
Sink and CPU
Cover
4-11
User’s Manual
4) Remove the 4 screws which hold the heat sink in place.
5) Gently remove the heat sink cable.
6) Lift the heat sink out of the computer
heat sink screws
Heat sink
4-12
O
L
Figure 4-3
heat sink cable
Chapter 4: Upgrading the Computer
B: Remove the processor
The processor is secured on the mainboard with a lock which is
easily opened using a small regular screwdriver.
With the heat sink already removed you will need to set the lock
to the open position before removing the processor:
processor mounted on the socket
O
L
Processor socket
Lock
4-13
User’s Manual
OPEN
2) Lift the processor
O
L
from the socket.
1) Turn the screw on the
processor lock to the
open position. (O)
O
L
C: Insert a new processor
1) With the processor lock in the open position, align the pins
of the processor with the holes in the socket.
2) Press the processor into
the socket.
4-14
O
L
Chapter 4: Upgrading the Computer
LOCK
3) Turn the screw to the locked
position (L)
O
L
D: Reinstall the heat sink
Note: When reinstalling the heat sink, you will also have to
replace the heat sink pad. A heat sink pad can be obtained from
your dealer.
1) Peel off the old heat sink pad and stick on a new one.
2) Insert the heat sink cable in the slot. (page 4-12,
Figure 4-3)
3) Align the 4 screw holes on the heat sink with those on the
mainboard and screw them in about half way. Once all the
screws are in about half way and the heat sink is seated
probably tighten the screws.
Heat sink pad
4-15
User’s Manual
E: Changing the SW1 DIP Switch settings
If you have installed the processor with Intel Speedstep you
will have to change the SW1 DIP Switch settings. Follow these
steps to get to change the SW DIP Switch setings:
1) Turn off the computer.
2) Press the two keyboard latches to elevate the keyboard
from its normal position (refer to page 4-7, Figure 4-1)
3) Carefully lift the keyboard assembly out to expose the
mainboard.
4) Remove the metal protective shield (refer to the picture
on page 4-17)
5) Locate the SW1 DIP Switch on the right side.
6) Change the settings to the following:
SW1 settings for Intel Speedstep® Processor
SW1-1 SW1-2 SW1-3 SW1-4
ON ON ON OFF
4-16
7) Put the metal shield back into place
8) Put the keyboard back into place.
Metal shield
Chapter 4: Upgrading the Computer
SW1 DIP Switch
ON position
OFF position
4-17
Chapter 5: BIOS Utilities
Chapter 5: BIOS Utilities
In this chapter you will learn about the Power On Self Test
(POST), power management and how to configure the system
parameters using the System Configuration Utility (SCU).
- Power on Self Test (POST)
- System Configuration Utilities
- Features of the SCU
. Startup Menu
. Memory Menu
. Disks Menu
. Components Menu
. Power Menu
. Exit Menu
- Power Management
5-1
User’s Manual
Power on Self Test (POST)
The system BIOS (Basic Input/Output System) performs a series
of tests on the system memory and key computer components
every time the computer is powered on. These tests are called the
Power On Self Test (POST). Should an error exist, the POST
routine may halt execution (depending on the problem). If no
error exists, the POST will initialize the BIOS configuration, and
boot (start) the operating system.
Post Message: Normal Operation
You will see the following message on the POST Screen if no
error exists after the POST is performed
SystemSoft MobilePRO BIOS Version 1.01 (2482-00)-(R1.00.pr03)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
500 MHz Pentium III with MMX CPU
CPU Microcode Update Rev 002h Complete
L2 Cache: 256K installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS Ver.1.17.01
Base Memory 000640 Kb
Extended Memory 121856 Kb
Total Memory 122880 Kb
Shared Memory 008192 Kb
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
INITIALIZING BOOT CD-ROM
INITIALIZING 2 nd A TAPI — None
5-2
Chapter 5: BIOS Utilities
Note:
You may press the Spacebar key to skip the memory test.
POST Message: Error Detected
If an error is detected, you will see the following WARNING
message on the POST Screen.
or press the Ctrl-Alt-S keys simultaneously to enter the System
Configuration Utility.
SystemSoft MobilePRO BIOS Version 1.01 (2482-00)-(R1.00.pr03)
Copyright 1983-1996 SystemSoft Corp. All Rights Reserved
500 MHz Pentium III with MMX CPU
CPU Microcode Update Rev 002h Complete
L2 Cache: 256K installed
8 MB Video RAM
SystemSoft Plug-n-Play BIOS Ver.1.17.01
You may press F1 key to continue,
Base Memory 000640 Kb
Extended Memory 121856 Kb
T otal Memory 122880 Kb
Shared Memory 008192 Kb
WARNING – HARD DISK CONTROLLER 1 FAILURE
Auto Detecting IDE Devices[Done]
<CTRL-ALT-S> to enter System Configuration Utility
Press F1 to Continue
5-3
User’s Manual
System Configuration Utility
The System Configuration Utility (SCU) can be used to set your
notebook's system parameters. Things like the date and time or
power settings are what you set in the SCU.
The settings are stored in a nonvolatile battery-backed CMOS
RAM. This means that your settings are saved even when the
notebook is turned off.
Information in the System Configuration Utility
Here is a list of the system settings which may be changed within
the System Configuration Utility.
This menu bar choice: Allows you to set or change:
Startup Date and Time, Fast Boot, Boot Device,
Display, Enable B a tter y Low Beep,
Enable LCD expand Mode, Enable Power
On Beep, E nable PNP OS Support,
Display OEM logo, Enable S/PDIF digital
output, Boot Password, SCU Password.
Memory Cache Systems, VGA Shared Memory.
Disks Diskette Drives, IDE Settings.
Components COM Ports, LPT Port, PS/2 Mouse Port,
Keyboard Numlock, Keyboard Repeat.
Power Enable Power Saving, Low Power Saving,
Medium Power Saving, High Power
Saving, Customiz e, Suspend Controls,
Resume Timer, Enable MODEM Ring
Resume, Enable Battery Low Suspend,
CPU SpeedStep Controls.
Exit Save and Exit, Exit (No Save), Default
Settings, Restore Settings, Version Info.
5-4
Chapter 5: BIOS Utilities
Initiating the System Configuration Utility
The System Configuration Utility (SCU) can be accessed by pressing the Ctrl, Alt, and S keys simultaneously when you turn on
your computer and see this message:
<CTRL-ALT-S> to enter System Configuration Utility
This message lasts only a few seconds and if you don’t respond in
time, the computer will initiate the boot process. If you were
unable to enter the SCU you must reboot the system and try
again.
Note: During startup, if your computer has a logo screen or picture appear instead
of the POST Screen, wait until a curser appears in the top right corner before hitting
<CTRL-ALT-S> to enter the System Configuration Utility
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Devices
Floppy Drive A = 1.44 MB
Hard Drive C = 4327 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
Press <Alt> key to activate menus, and cursor keys to navigate. Mouse left
button, spacebar, and <Enter> keys accept menu item. Mouse right button and
<Esc> key cancel current action.
System
CPU Clock = 500 MHz
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 6 4 KB
Reserved = 320 K B
Total RAM = 122880 K B
Cache (EXT) = 256 K B
5-5
User’s Manual
Working with the Menu Bar
Use these keys to begin working in the SCU.
Keys Action
Alt Highlights the menu bar
Left arrow ( ← )
Right arrow ( → )
Highlighted letters
Selects a menu bar option.
Left mouse button
Down arrow ( ↓ )
Spacebar
Enter
Right mouse button
Esc
Opens the menu bar option.
Cancels current action
Working with the Pull-down Menu (Submenu)
Once your desired menu bar item is highlighted, press Enter or
the down arrow to see the pull-down menu items. You move
about the pull-down menu with these keys:
Keys
Down/Up arrows (↓) ( ↑ )
Highlighted letters
Enter Enable/disable the specified
Esc Close the pull-down menu and
Action
Select a pull-down menu item.
function.
A (√) indicates, the fu n cti o n i s on.
Save the changes .
5-6
Chapter 5: BIOS Utilities
Some Pull-Down menu options have an arrow to the left of the
entry. Choose these options by pressing Enter and another
screen will be displayed. Navigate the new screen with the
following keys:
Keys
Tab Move from one record to
Down/Up arrows (↓)( ↑ )
Spacebar Select a field
Enter Choose <OK> to save any
Esc Quit
Action
another.
Change the value of a field.
changes.
<Cancel> to ignore any
changes.
5-7
User’s Manual
Features of the SCU
Startup Menu
Item
Date and Time Day/Month/Year
Fast Boot
Boot Device
Display
Setting/Option Function
Hour/Minute/Second
Enable Initialize and
Disable Disable the Fast
Hard Disk C
1st Boot
Device
nd
2
Boot
Device
3rd Boot
Device
LCD Activate the system’s
CRT Activate an external
LCD + CRT Activate both the
CD-ROM
Drive
Diskette A
Hard Disk C
CD-ROM
Drive
Diskette A
Hard Disk C
CD-ROM
Drive
Diskette A
Set the date and
time.
quickly boot the
system by skipping
certain diagnostic
tests.
Boot.
Specify the system’s
1st choice for the boot
drive.
Specify the system’s
2nd choice for the
boot drive.
Specify the system’s
3rd choice for the
boot drive.
LCD panel.
monitor.
LCD and the CRT.
5-8
Startup Menu (continued)
Item
Enable Battery
Low Beep
Enable LCD
Expand Mode
On Beep
Support
logo
digital ou tpu t
Boot Password
SCU Password
Setting/Option Function
Enable A series of warning beeps
Disable D isable the above.
Enable Stretch the dis p lay to fill th e
Disable D isable the above.
Enable Enable Power
Disable
Enable Enable PNP OS
Disable
Enable Display OEM
Disable
Enable Enable S/PDIF
Disable
Enter old P o w e r-O n
Password
Enter new Power-On
Password
Verify new Power-On
Password
Enable Password to
Power-On
Enter ol d S e tu p
Password
Enter n ew S e tu p
Password
Verify new Setup
Password
Enable Setup Password
Chapter 5: BIOS Utilities
will sou n d w h e n th e b a tte ry
power is lo w .
entire area of the LCD
panel.
Enable or Disable Power
On Beep.
Enable or disable PNP OS
Support
During co mputer startup
anothe r pictu re ca n be
shown in place of the POST
Screen (Power on Self Test)
Enable or Disable S/PDIF,
which is u s ed fo r dig ital
audio output.
Set a password for booting
the computer.
Only users who enter a
correct pas sw o rd ca n b oo t
the system.
Set a password for
modify in g th e SC U. Only
users w h o e n ter th e co rrect
passwo rd ca n ch a ng e the
SCU.
5-9
User’s Manual
Startup Menu (continued)
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup
Startup Memory Disks Components Power Exit
Date and Time !
Devices
Ö Fast Boot
Boot Device !
Floppy Drive A = 1.44 MB
Display !
Hard Drive C = 4327 MB
Ö Enable Battery Low Beep
Hard Drive D = 0 MB
Ö Enable LCD expand mode
Hard Drive E = 0 MB
Ö Enable Power On Beep
Hard Drive F = 0 MB
Ö Enable PNP OS Support
Serial Port 1 = COM 1, 3F8, IRQ 4
Ö Display OEM logo
Serial Port 2 = COM 2, 2F8, IRQ 3
_ Enable S/PDIF digital output
Parallel Port = LPT1, Addr 378, IRQ 7
Boot Password !
SCU Password !
Set system date and time
System
CPU Clock = 500 MHz
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 6 4 KB
Reserved = 320 K B
Total RAM = 122880 K B
Cache (EXT) = 256 K B
5-10
Memory Menu
Item Setting/Option Function
Chapter 5: BIOS Utilities
Cache
Systems
L1 Cache
Disabled Disable the processor’s internal
cache.
Write Back Enable the Processor’s internal
write-back cache.
L2 Cache
Disabled Disable the L2 cache controller.
Write Back Enable the LS write-back cache.
VGA
shared
memory
8 MB
16 MB
Select the VGA shared memory
size
32 MB
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Memory
Cache System !
Devices
VGA Shared Memory !
Floppy Drive A = 1.44 MB
Hard Drive C = 4327 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
System
CPU Clock = 500 MHz
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 6 4 KB
Reserved = 320 K B
Total RAM = 122880 K B
Cache (EXT) = 256 K B
Internal and External cache settings
5-11
User’s Manual
Disks Menu
Item Setting/Option Function
None Diskette
1.44 MB
Drive
Enabled
Specify the drive
types for the
diskette drive A.
Enable enhanced
IDE settings.
Drives
IDE
Settings
Drive A
Primary HDD
PIO Mode
CD-ROM /
DVD-ROM /
Drive
Enabled
PIO Mode
Enable IDE UDMA33/66/100
Function
IDE 32 Bit I/O
Disable
Enable
Disable
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Devices
Floppy Drive A = 1.44 MB
Hard Drive C = 1359 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
Disks
Diskette Drives !
IDE Settings !
System
CPU Clock = 500 MHz
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 64 KB
Reserved = 320 K B
Total RAM = 122880 K B
Cache (EXT) = 256 K B
Configure diskette drives A and B
5-12
Components Menu
Item Setting/Option Function
COM Ports
LPT Port
COM A I/O
Settings
COM B I/O
Settings
Mode
Setting for
COM B
DMA
Setting for
Fast IR
Port
Address
Port
Definition
Setting For
ECP Mode
EPP Type EPP 1.9 Specify the EPP type.
None
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8,
IRQ10
COM4, 2E8,
IRQ11
None
COM1, 3F8, IRQ4
COM2, 2F8, IRQ3
COM3, 3E8,
IRQ10
COM4, 2E8,
IRQ11
Normal (16550)
IrDA (HPSIR)
ASK IR
FAST IR
DMA 0
DMA 1
DMA 3
None
LPT1, Addr 378,
IRQ7
LPT2, Addr 278,
IRQ5
LPT3, Addr 3BC,
IRQ7
Standard AT (Centronics)
Bidirectional (PS-2)
Enhanced Parallel (EPP)
Extended Capabilities (ECP)
DMA 1 DMA
DMA 3
Specify t he COM A
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
Specify the COM B
configuration. (COM3
& COM4 Only for DOS
mode and Non-PnP
OS.)
Define the COM B
hardware.
Specify the Fast IR
DMA configuration.
Specify the LPT port
and IRQ configuration.
Specify the ECP DMA
configuration.
Chapter 5: BIOS Utilities
5-13
User’s Manual
C
(COM)
Components Menu (continued)
Item Setting/Option Function
PS/2 Mouse
Enable Enable the system’s
Port
Disable Disable the trackpad or
Enable Keyboard
Numlock
Keyboard
Repeat
Disable
Key Repeat
Rate
2 cps
6 cps
10 cps
15 cps
20 cps
30 cps
Key Delay
1/4 sec
1/2 sec
3/4 sec
1 sec
trackpad or an external
PS/2 mouse.
PS/2 mouse if an
external mouse is
connected to COM A
port.
Specify whether Num
Lock is on or off at
system boot time.
Define the rate
(characters per second)
at which the keyboard
repeats while a key is
depressed.
Specify the amount of
time (second) that will
pass after a key is
depressed before the
key starts to repeat.
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Devices
Floppy Drive A = 1.44 MB
Hard Drive C = 1359 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
onfigure serial
Components
COM Ports !
LPT Port !
Ö PS/2 Mouse Port
Ö Keyboard Numlock
Keyboard Repeat !
port I/O addresses
System
CPU Clock = 500 MHz
Memory
Base = 640 KB
Extended = 121856 KB
Shadow = 6 4 K B
Reserved = 320 KB
Total RAM = 122880 K B
Cache (EXT) = 25 6 KB
5-14
Power Menu
Item Setting/Option Function
Chapter 5: BIOS Utilities
Enable Enable Power
Saving
Saving
Saving
Saving
Customize Disk
Disable
Enable Low Power
Disable
Enable Medium Power
Disable
Enable High Power
Disable
Standby
5 sec
10 sec
20 sec
30 sec
1 min
5 min
10 min
Enable/Disable all power
saving features.
Enable/Disable the power
saving to its lowest which
results in ma x. performance
but shortest battery life.
Enable/Disable the power
saving to its medium which
results in both moderate
performance and battery life.
Enable/Disable the power
saving to its highest which
results in min. performance
but longest battery life.
The hard disk will be put on
standby if it is not accessed
within the specified period.
Hard disk power will be
restored when the disk drive
is accessed again.
Always
on
5-15
User’s Manual
Power Menu (continued)
Item Setting/Option Function
Suspend
Controls
Power
Button
Function
Power On/Off The power button is
switched to turn the
system on or off.
Resume Timer
Enable
MODEM Ring
Resume
Enable
Battery Low
Suspend
CPU
Speedstep
Controls
Suspend
Type
Resume
Resume
Month/Day/Hour/Minute
Enable Resume the system
Disable Disable the above.
Enable Automatically
Disable Disable the above.
Maximum performance mode always
Battery optimized mode always
Automatically switch between Maximum
performance and Battery optimized.
Suspend to
Disk
Powered on
Suspend
Enable Alarm
Disable
Specify the suspend
mode for power
management.
Resume the system
from the configured
suspend mode when
resume alarm timer
expires.
The system will
resume at the
specified time
(month, day, hour
and minute).
from STR or POS
mode when a modem
ring is detected
(which modem should
be connected to the
serial port).
suspend the system
to disk upon a low
battery condition.
5-16
Chapter 5: BIOS Utilities
Power Menu (continued)
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Devices
Floppy Drive A = 1.44 MB
Hard Drive C = 4327 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
Select the operating mode for SpeedStep CPU
Power
Ö Enable Power Saving
_ Low Power Saving
_ Medium Power Saving
_ High Power Saving
Ö Customize !
System
CPU Clock= 500 MHz
Suspend Controls !
Resume Timer !
_ Enable MODEM Ring Resume
_ Enable Battery Low Suspend
CPU Speedstep Controls !
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 6 4 KB
Reserved = 320 K B
Total RAM = 122880 K B
Cache (EXT) = 256 K B
5-17
User’s Manual
Exit Menu
Item Function
Save and Exit Exits the utility and saves all changes
Exit (No Save) Exit without saving any current
Default Settings Loads the default (factory) settings for
Restore Settings Restore the current setup settings to
Version Info Show current BIOS version
to CMOS ;then reboot the system.
changes.
all items.
the original custom ones.
information.
SystemSoft SCU For SiS 630S/540 chipset Dec 2, 1999 5:39:51 pm
Startup Memory Disks Components Power Exit
Devices
Floppy Drive A = 1.44 MB
Floppy Drive A = 1.44 MB
Hard Drive C = 4327 MB
Hard Drive C = 4327 MB
Hard Drive D = 0 MB
Hard Drive D = 0 MB
Hard Drive E = 0 MB
Hard Drive E = 0 MB
Hard Drive F = 0 MB
Hard Drive F = 0 MB
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 1 = COM 1, 3F8, IRQ 4
Serial Port 2 = COM 2, 2F8, IRQ 3
Serial Port 2 = COM 2, 2F8, IRQ 3
Parallel Port = LPT1, Addr 378, IRQ 7
Parallel Port = LPT1, Addr 378, IRQ 7
Exit
Save and Exit !
Exit (No Save) !
Default Settings !
Restore Settings !
Version Info !
Memory
Base = 640 K B
Extended = 121856 K B
Shadow = 6 4 KB
Reserved = 320K B
Total RAM = 122880 K B
Cache (EXT) = 256KB
CPU Clock= 500 MHz
Save current settings and return to previous work
5-18
Chapter 5: BIOS Utilities
Power Management
You can manage power consumption while maintaining system
performance by setting your computer to one of the available
power management modes. Information on the various types of
power management are listed below. If you want information on
how to set the power management options please refer to the
Power Menu in this chapter.
Advanced Power Management (APM 1.2)
To reduce power consumption, the system provides built-in
Advanced Power Management (APM 1.2). The APM function
varies depending on your operating system (OS). Some operating
systems, such as Windows NT do not support APM.
Advanced Configuration and Power Interface (ACPI)
ACPI enables a computer to turn its peripherals on and off for
improved power management. It also allows the PC to be turned
on and off by external devices, so that the pressing a trackpad
button or the keyboard will "wake up" the machine.
Disk Standby
The computer's hard disk drive motor will be turned off if the
hard drive has not been accessed for a specified period of time. If
the system reads or writes data the hard disk motor will be
turned back on.
5-19
User’s Manual
Suspend and Resume
With this function you can stop an operation and restart where
you left off. The hard disk is turned off, and the CPU is made to
idle at its slowest speed and all open applications are retained in
memory. This system features two suspend mode levels:
Powered On Suspend (POS) and Suspend to Disk (SD).
Caution: Do not enter suspend mode when you are:
1: Accessing any of the disk drives, such as the HDD, FDD or
DVD-ROM drive.
2: Using any audio or video applications.
3: Playing a DOS game.
Powered On Suspend (POS)
Powered On Suspend saves the least amount of power, but takes
the shortest time to return to full operation. When you are not
using your computer for a certain length of time, which you
specify in the SCU Power Menu, it will enter POS mode to save
power.
Resume from POS Mode
The system can resume from POS mode by:
• Pressing any keyboard key.
• Pressing the power button (if configured as a Suspend/
Resume function under SCU)
• An incoming call to your modem.
• Alarm resume is enabled and expires.
5-20
Chapter 5: BIOS Utilities
Suspend to Disk
Suspend to Disk uses no power and saves all of your information
on a part of the HDD. It saves the maximum power but takes the
longest time to return to full operation. You can set your notebook to automatically enter Suspend to Disk mode when the
battery power is almost depleted. This prevents losing any data
due to loss of power. To set this feature, go to the SCU Power
Menu and choose Enable Battery Low Suspend.
In order to use Suspend to Disk, you must partition your Hard
Disk Drive, the instructions are as follows:
1: Use your operating system's FDISK program to delete all
hard disk partitions if any already exist on the target drive.
2: Boot the system and run the 0VMAKFIL.EXE Utility to
create the Suspend to Disk partition on the hard disk. The
size of the Suspend to Disk partition will be the installed
DRAM (n) plus 8 MB integrated video RAM.
:\>0VMAKFIL -Pn
For example, if the system DRAM is 32 MB, 0VMAKFIL
will create a partition size of approximately 40 MB.
:\>0VMAKFIL -P32
Resume from Suspend to Disk Mode
The system will resume from Suspend-to-Disk mode by:
• Pressing the power button.
• Alarm resume (month/day/hour/minute)
5-21
Chapter 6: Installing Drivers
Chapter 6: Installing Drivers
This chapter provides step-by-step instructions for installing
device drivers and utilities, for more detailed information please
refer to your operating system's manual or the product manual
supplied with the device you wish to install. The information
here has been designed for users with basic computer knowledge
though inexperienced users may also find this section helpful. (In
this chapter, we assume the DVD-ROM drive as drive E.)
The chapter includes:
- Preparation for a New Notebook
- Installing Windows 98 SE (For reference only)
- PC Card Problem in Windows 98
- Installing Windows 2000 (For reference only)
- Installing Drivers in Windows 98 SE
- Installing Drivers in Windows 2000
- Installing Drivers in Windows NT4.0
6-1
User’s Manual
Preparation for a New Notebook
1) Use a bootable floppy disk to start the system.
2) Run the FDISK utility from DOS to create a bootable
partition. (See DOS manual for the operation details.)
3) Format the hard disk.
Follow the command “Format C: /S”
to create a bootable hard disk and make the boot system
files.
(C:/S copies system files to the formatted disk)
4) Copy the file “MSCDEX.exe” from the floppy disk to
drive C.
5) Insert the CD-ROM/DVD-ROM driver disk.
Type “A: Install”.
6) Restart the system.
Note 1: Using another computer you can copy the CD-ROM/DVD-
ROM driver from the CD-ROM disk on to a floppy disk.
Note 2: If the supplied CD-ROM/DVD-ROM driver does not offer an
install program, you can copy the driver to drive C, and then
configure the Config.sys and Autoexec.bat files.
6-2
Chapter 6: Installing Drivers
Installing Windows 98 SE (For Reference Only)
1) Start DOS.
2) Insert the Windows 98 CD-ROM.
3) Type “setup”, then press Enter.
4) When the “Windows 98 Setup” program initializes, click
Continue.
5) When the “License Agreement” dialog box appears. Select
“I accept the Agreement” and click Next.
6) At the “Windows Product key” prompt, enter the
product’s ID number and press Next.
7) When the “Select Directory” dialog box appears. Select
the path “C:\Windows”, or type another path if you
prefer. Then click Next.
8) When you see “Setup Options”, select “Portable” and click
Next.
9) Follow the on-screen instructions and choose the
recommended options.
10) Restart your computer.
6-3
User’s Manual
After installation of Windows 98 or Windows 98 Second
Edition, you may find that the PC cards arenot working
normally and you may noticed one or more of the following:
- An exclamation mark appears in the PC card driver
in Device Manager
- PC cards don’t work at all
- PC card controllers are not enumerated
- PC card controllers are disabled on power-up
- PC card controllers are disabled when you resume
the computer from Suspend mode
This is a problem caused by Microsoft Windows 98 (Second Edition). To resolve the problem, immediately after
installing Windows 98SE install the program file
PCI.vxd to update your system driver. The PCI.vxd
driver is supplied by your computer dealer.
For more information on this, refer to the Microsoft article “CardBus Device Not Enumerated with TI 14xx or
44xx CardBus Controllers” (Article ID: Q233017) which
can be found on Microsoft’s web site.
PC Card Problem in Windows 98
6-4
Chapter 6: Installing Drivers
Installing Windows 2000 (For Reference Only)
Note: The installation steps could be a bit different depending on your
system’s status. For details, refer to your Windows 2000 manual.
1) Start DOS.
2) Insert the Windows 2000 Installation CD-ROM disk.
3) Change the directory to I386 or wherever the file
“WINNT.exe” is located.
4) Type “WINNT”, and press Enter.
5) “Windows 2000 Setup” appears, press Enter to continue.
6) “Windows 2000 Professional Setup” starts copying files to
your HDD.
7) After copying, press Enter to restart your computer.
8) After entering “Windows 2000 Professional Setup”, press
Enter to “set up Windows 2000 now”.
9) Press F8 for “Windows 2000 Licensing Agreement”.
10) Select the drive (partition) where you want to install
Windows 2000, and press Enter.
11) Choose the file system you want and press Enter. (The
“FAT” file system is recommended.)
12) To format the drive (partition), press F. (Please note all
data on the formatted drive will be lost.)
13) Setup will proceed with formatting, file-copying, and
then reboot the system.
14) When the system enters Windows 2000, follow the onscreen instructions and press Next.
15) When Windows asks for Your Product Key, type the
product’s ID number and then press Next.
16) Continue to press Next until Setup starts to install
6-5
User’s Manual
various components, and performs its final tasks.
17) Click Finish to complete Windows 2000 Setup Wizard.
18) The computer will restart Windows 2000 automatically.
Installing Drivers in Windows 98 SE
Step 1: Installing the LAN driver
1) Click Start.
2) Select Run.
3) Choose the path E:\LAN\WIN98\Setup.exe
4) Run Setup.exe.
5) Follow the on-screen instructions, and continue to press
Next.
6) Click Finish to restart your computer.
Step 2: Installing the VGA driver
1) Click Start.
2) Select Run.
3) Choose the path E:\video\Win9X\Setup.exe
4) Run Setup.exe.
5) Follow the on-screen instructions, and continue to press
Next.
6) Click Finish to restart your computer.
Step 3: Installing the Audio Driver
If you intend to use your computer with the DVD and external
speakers, you can have a better sound quality if you use S/PIF.
This simply requires installing a different audio driver and
making a change in the SCU.
6-6
Chapter 6: Installing Drivers
(Without S/PDIF)
1) Click Start.
2) Select Run.
3) Specify the path to E:\Audio\Win98\Setup.exe
4) Run Setup.exe.
5) Follow the on-screen instructions, and continue to press
Next.
6) Click Finish to restart your computer.
(With S/PDIF)
1) Remove the previous audio driver if already installed.
2) Reboot the computer and go to the SCU by pressing
Ctrl+Alt+S.
3) Enable S/PDIF under the Startup menu
4) Click Start and select Run.
5) Type E:\Audio\Win98\Setup.exe -vxd and press OK
to install the audio driver.
6) Click Finish to restart your computer.
For more information on the driver, refer to the Readme file under the
directory.
Step 4: Installing the Modem Driver (Optional)
1) Click Start.
2) Select Settings and Control Panel.
3) Double click the System icon.
4) Click the Device Manager tab.
5) Locate the “PCI Communication Device” under “Other
devices”.
6-7
User’s Manual
6) Double click “PCI Communication Device”
7) Click the Driver tab and choose Update Driver.
8) Press Next.
9) Select “Search for a better driver than the one your
device is using now” and press Next.
Select “Specify a location” and choose Browse to specify
the location to E:\MDC\Win98
10) Press OK.
11) Follow the on-screen instructions and press Next.
12) Click Finish to complete the setup.
13) Restart your computer.
Step 5: Installing the PCMCIA Driver (Optional)
1) Click Start.
2) Select Settings and Control Panel.
3) Double click the System icon.
4) Click the Device Manager tab.
5) Click on “PCMCIA socket”
6) Select “Generic Card Bus Controller”
7) Choose Remove.
8) Press Refresh
9) In the “Add New Hardware Wizard” window, press Next.
10) Select “Search for the better driver for your device” and
press Next.
11) Select “Specify a location” and choose Browse to specify
the location to E:\Pcmcia\Win98
12) Press OK. You should now see the driver EnE Tech
CB1410 Card Bus Controller being loaded.
13) Follow the on-screen instructions and press Next.
6-8
Chapter 6: Installing Drivers
14) Click Finish to complete the setup.
15) Restart your computer.
Step 6: Installing the DVD driver.
Note: If you intend to connect you notebook computer with
external speakers when using the DVD you will need to
first install the audio driver capable of handling S/PDIF.
Please refer to Step 3: Installing the Audio Driver
(with S/PDIF) for more information.
1) Insert the Win DVD CD-ROM into your drive, The
installation program automatically runs when you insert
the DVD disk into the DVD-ROM drive.
2) After the DVD driver is installed, click Start and select
Settings and Control Panel.
3) Double click the System icon.
4) Click the Device Manager tab.
5) Select the DVD-ROM type device located under
“CDROM.”.
6) Click the Properties button.
7) Click the Settings tab, and enable DMA mode..
8) Restart the computer.
9) Start the DVD player and go to Propreties (The third
icon from the right).
10) Select Audio
11) Select Enable S/PDIF
6-9
User’s Manual
Installing Drivers in Windows 2000
Step 1: Installing the LAN Driver
1) Click Start.
2) Select Run.
3) Open the path to E:\LAN\WIN2000\SETUP.EXE.
4) Run SETUP.EXE.
5) Follow the on-screen instructions, and press Next.
6) Choose “No, I will restart my computer later” and click
Finish.
Step 2: Installing the VGA Driver
1) Click Start.
2) Select Run.
3) Open the path to E:\VGA\WIN2000\SETUP.EXE.
4) Run SETUP.EXE.
5) Follow the on-screen instructions, and press Next.
6) Choose “No, I will restart my computer later” and click
Finish.
Step 3: Installing the AGP Driver
1) Click Start.
2) Select Run.
3) Open the path to E:\WIN2000\AGP\SETUP.EXE.
4) Run SETUP.EXE.
5) Follow the on-screen instructions, and press Next.
6) Choose “No, I will restart my computer later” and click
Finish.
6-10
Chapter 6: Installing Drivers
Step 4: Installing the Audio Driver
1) Click Start.
2) Select Run.
3) Open the path to E:\Audio\SETUP.EXE.
4) Run SETUP.EXE.
5) Follow the on-screen instructions, and press Next .
6) When the “Digital Signature Not Found” dialog box
appears, choose Yes to continue the installation.
7) Click Finish to restart your computer now.
For more information, please refer to the Readme file under the
directory.
Step 5: Installing the Modem Driver (Optional)
1) Click Start.
2) Select Settings and Control Panel.
3) Double click the System icon.
4) Click the Hardware tab and choose Device Manager.
5) Locate “PCI Simple Communicatons Controller” under
“Other devices”.
6) Double Click “PCI Simple Communicatons Controller” to
go to the PCI Device Properties window.
7) Select Driver tab
8) Select “Update Driver”
9) Select Next
10) Select “Search for a suitable driver for my device” and
press Next.
11) Select “Specify a location” and press Next.
12) Choose Browse to specify the path to either
6-11
User’s Manual
E:\modem\Win2000
13) Click Next to install the driver.
14) If the “Digital Signature Not Found” dialog box appears,
press Yes to continue.
15) Click Finish to complete the setup.
16) Close the Modem Properties window.
17) Restart your computer.
Step6: Installing the PCMCIA Driver (Optional)
1) Click Start.
2) Select Settings and Control Panel.
3) Double click the System icon.
4) Click the Hardware tab and choose Device Manager.
5) Click on “PCMCIA adapters”
6) Double click on “Generic Card Bus Controller”
7) Select Driver tab
8) Select “Update Driver”
9) Select Next
10) Select “Search for a suitable driver for my device” and
press Next.
11) Select “Specify a location” and press Next.
12) Choose Browse to specify the path to either
E:\Pcmcia\Win2000
13) Click Next to install the driver. You should now see the
driver EnE Tech CB1410 Card Bus Controller being
loaded.
14) Click Finish to complete the setup.
15) Close the PCMCIA Properties window.
16) Restart your computer.
6-12
Chapter 6: Installing Drivers
Step 7: Installing the DVD driver (optional).
Insert the Win DVD CD-ROM into your drive and follow the
instructions.
Step 8: Installing the SiSIDE Driver
1) Click Start.
2) Select Run.
3) Open the path to E:\Utility\Setup.exe
4) Run Setup.exe\
5) Follow the on-screen instructions.
Note: The computer will not restart automatically once the
setup process completes, you will need to restart your computer
for the changes to take effect.
6-13
User’s Manual
Installing Drivers in Windows NT4.0
Note 1: After installing Windows NT4.0, please install the
latest Service Pack to enhance the function. Download the
latest Service Pack version from the Microsoft web site.
Note 2: Before installing the following drivers, press
“Ctrl+Alt+S” to enter the SCU when the computer boots. In the
Startup Menu, deselect “Enable PNP OS Support” and choose
“Save and Exit” in the Exit Menu
Step 1: Installing the VGA Driver
1) Click Start.
2) Select Control Panel.
3) Double Click on Display
4) Select the Settings Tab
5) Choose Display Type
6) Choose Change
7) Select Have Disk
8) Open the path to E:\WINNT40
9) Click OK
10) Click OK
11) Select YES when you see “You are about to install a
third-party driver”
12) Click OK
13) Close the Display Properties Window
14) Select Yes to restart you computer
6-14
Loading...