Euroboor ECO.30, ECO.32 User Manual
FOR PROFESSIONALS BY PROFESSIONALS
USER MANUAL
E U R O B O O R
ECO.30
Magnetic Drilling Machine
SERIAL NO.____________ DATE OF PURCHASE __________
Congratulations on your purchase of the Euroboor ECO.30 Portable Magnetic Drilling Machine. Your
model is designed to produce superior holes quickly and efficiently. Through years of experience,
constant innovation and development, Euroboor BV is committed to provide you with metal cutting
tools and products to help you be more productive.
Before operating your new magnetic drilling machine, please read all instructions first. These include
the Operator’s Manual and Warning Label on the unit itself. With proper use, care and maintenance,
your model will provide you with years of effective hole drilling performance.
TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND ALL INSTRUCTIONS
0800 536 774
sales@gwsnz.co.nz
www.globalweldingsupplies.com
13 Patiki Road Avondale, Auckland 1026
ISSUE 1/Original version/OCT 2014
2
Fig. 1
ISSUE 1/Original version/OCT 2014
3
Symbol Term, meaning Explanation
mm
Read documentation
Wear ear protection
Wear eye protection
Danger/warning/caution
European conformity symbol
Class of protection I
Millimeter
Be absolutely sure to read the enclosed
documentation such as the Instruction Manual and
the General Safety Instructions.
Use ear protection during operation.
Use eye-protection during operation.
Observe the information in the adjacent text!
Confirms the conformity of the power tool with
the directives of the European Community.
Product with basic insulation and exposed
(touchable), conductive parts additionally
connected to the protective earth conductor.
Unit of measure for length, width, height or depth
kg
V
A
W
N
min
no
Kilogram
Volt
Ampere
Watt
Newton
Minutes
No-load speed
Unit of measure for the mass
Unit of measure for the electric voltage
Unit of measure for the electric current intensity
Unit of measure for the output
Unit of measure for the force
Unit of measure for the time
Revolution speed at no-load
1/min
per minute
ISSUE 1/Original version/OCT 2014
0800 536 774
sales@gwsnz.co.nz
Unit of measure for number of revolutions,
strokes, impacts or oscillations per minute.
www.globalweldingsupplies.com
13 Patiki Road Avondale, Auckland 1026
4
GENERAL POWER TOOL SAFETY WARNINGS
Do not use this power tool before you have thoroughly read and completely understood this
Instruction Manual and the “General Safety Instructions”, including the figures, specifications, safety
regulations and the signs indicating DANGER, WARNING and CAUTION.
WARNING: When using electrical tools basic safety precautions should always be followed to
reduce the risk of fire, electrical shock and personal injury including following.
Please also observe the relevant national industrial safety regulations. Non-observance of the safety
instructions in the said documentation can lead to an electric shock, burns and/or severe injuries.
This Operator’s Manual and the “General Safety Instructions” should be kept for later use and
enclosed with the power tool, should it be passed on or sold.
WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2. Do not operate magnetic drilling machine in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Magnetic drilling machine may create sparks which may
ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operating a magnetic drilling machine.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Magnetic drilling machine plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs.
2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is grounded.
3. Do not expose magnetic drilling machines to rain or wet conditions. Water entering a
machine will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord to carry the magnetic drilling machine or pull the
plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
5. When operating a magnetic drilling machine, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a magnetic drilling machine in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when using a magnetic drilling
machine. Do not use machine while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating magnetic drilling machines may result
in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying magnetic drilling
machines with your finger on the switch or plugging in magnetic drilling machines that have
the switch on invites accidents.
ISSUE 1/Original version/OCT 2014
5
4. Never place hands, fingers, gloves or clothing near cutting area or rotating machine parts.
5. Remove adjusting keys or switches before turning the machine on. A wrench or a key that is
left attached to a rotating part of the machine may result in personal injury.
6. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the magnetic drilling machine in unexpected situations.
7. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
8. Always use supplied safety chain during any work on non-horizontal components. Mounting
can release.
MACHINE USE AND CARE
1. When using the machine on non-horizontal surfaces, you must use cutting paste. Do not use
oil because the oil can drip into the motor unit.
2. During machine operations, the annular cutter must be cooled and lubricated with good
quality cutting or lubrication oil. Remove the slug from the annular cutter after each hole.
Caution, the slug may be hot!
3. Use clamps or other practical way to secure and support the work piece to a stable platform.
Holding the work by hand or against your body is unstable and may lead to loss of control.
4. Do not use machine if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
5. Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventive safety measures reduce the risk of starting
the tool accidentally.
6. Store idle Magnetic drilling machines out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
7. Maintain machines with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.
8. Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the machine operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
9. Use only accessories that are recommended by Euroboor BV for your model. Accessories that
may be suitable for one machine, may become hazardous when used on another machine.
SERVICE
1. Tool service must be performed only by qualified repair personnel. Service or maintenance
performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.
3. When using this machine, you MUST wear ear and eye protection.
0800 536 774
sales@gwsnz.co.nz
ISSUE 1/Original version/OCT 2014
www.globalweldingsupplies.com
13 Patiki Road Avondale, Auckland 1026
6
ADDITIONAL SPECIFIC SAFETY RULES FOR MAGNETIC DRILLING MACHINES
• Keep your fingers well out of the drill area;
• Avoid touching the drilled core that is automatically ejected by the centering pin when the
working procedure is finished. Contact with the core when it is hot, or if it falls, can cause
personal injuries;
• Always use the drill guard. Before turning on machine ensure the guard is closed securely;
• Always use the safety strap;
• The magnetic drilling machine is suitable for use on steel with a thickness starting from 10
mm, with zero air gap between the magnet core surface and the mounting surface.
Curvature, coats of paint and surface irregularities will create an air gap. Keep the air gap to a
minimum;
• Always place the machine on a flat surface;
• Do not clamp the magnetic drilling machine on small or irregularly shaped objects;
• Always place the machine on a surface that is clear of shavings, chips, swarf and surface dirt;
• Keep the magnet clean and free of debris and swarf;
• Do not turn on the machine until it has been mounted and installed according to these
instructions;
• Do not turn on the machine before having checked that the magnetic stand has been
tightened firmly to the mounting surface;
• Adjust the table so cutter does not extend into the work piece before drilling. Do not perform
any design, assembly or construction activities on the work piece while the machine is turned
on;
• Before turning on the machine, make sure the accessory has been mounted correctly;
• Always use the recommended speed for the accessories and the material;
• Do not use the machine on the same work piece on which electric welders are being used;
• Use only an appropriate cutting fluid. We offer a range of premium cutting oils and lubricants
which are specially developed and selected for optimum performance and maximum tool
life;
• Do not use liquid cutting fluids while drilling vertically or overhead. Dip the cutter in cutting
paste or apply an appropriate spray for these applications;
• Do not pour cutting fluid into the reservoir while it is mounted in the bracket. Do not allow
cutting fluid to enter the drill motor;
• Before use, ensure movable chuck guard operates properly;
• Ensure that metal chips or resinous residue cannot lead to blockage of the function;
• In case of jammed cutter disconnect the machine from the power supply, remove the reason
for the jam before turning on the machine again.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing;
• Risk of personal injury from flying particles;
• Risk of burns due to accessories becoming hot during operation;
• Risk of personal injury due to prolonged use.
ISSUE 1/Original version/OCT 2014
7
Loading...