Euro Appliances EBC600SX Instruction Manual

Beverage

Cooler

EBC600SX

EURO APPLIANCES BY EUROSTYLE GROUP

Warning

The information in this document is subject to modification without any prior notice.

This beverage cooler is recommended for indoor use. It’s only used for storage

of beers and beverages.

Euro Appliances offers no guarantee for our beverage cooler if it is being used

for any purpose other than that for which it was specially designed. Euro

Appliances cannot be held responsible for any error in this manual. Euro

Appliances is not responsible or liable for any spoilage or damage to beverages

or any other contents incidental or consequential to possible defects of the

beverage cooler. Warranty applies to the beverage cooler only and not to the

contents of the beverage cooler.

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure they do not play with the appliance.

Allow 24 hours before switching on the beverage cooler. During this time we

recommend that you leave the door open to clear any residual odours.

Before loading & plugging in the beverage cooler, we recommend the location

you should have selected for your wine cooler should:

- Be unencumbered and well ventilated;

- Be well away from any heat source and direct sunlight;

- Not be too damp (laundry, pantry, bathroom, garage and basement etc.);

- Have a flat floor and place on a dry level surface;

- Have a standard and reliable electricity supply(standard socket to country

standards, linked to the ground),it is not recommended to use a multi-socket or

extension lead;

- Have a surge protector fitted to the electrical outlet

- Away from microwave. Certain microwave ovens do not have wave interference

shield. When place within 1 meter vicinity of the beverage cooler, they may

affect the operation of the beverage cooler.

The beverage cooler should be placed where the ambient temperature is

between 5 ºC to 38 ºC. If the ambient temperature is above or below this range,

the performance of the unit may be affected. Placing your unit in extreme cold

or hot conditions may cause interior temperatures to fluctuate; the idea range of

temperature may not be reached.

*Grounding Instructions

The beverage cooler must be grounded in case of an electrical short circuit.

Grounding reduces the risk of electrical shock. The beverage cooler is equipped

with a power cord having a grounding wire and plug. The beverage cooler plug

must be plugged into properly installed and grounded electrical outlet. In

locations where there is frequent lightening, it is advisable to use surge

protectors.

Improper use of the grounding plug can result in the risk of electric shock.

Consult a qualified electrician or service person if the grounding instructions are

not completely understood. If the supplied power cord is damaged, it must be

replaced by a qualified person in order to avoid electrical hazard.

*Installing your wine cooler

Unpack and remove all of the protection and adhesive strips from the packaging

around and inside the beverage cooler.

Important: Before connecting the unit to

a power source, please let it stand upright for approximately 24 hours. This will

reduce the possibility of a malfunction in the cooling system from handling

during transportation.

The beverage cooler must be positioned that the plug is accessible. Release

the power cord and move your beverage cooler to its finally location. The

beverage cooler should be installed in a suitable place where the compressor

will not be subject to physical contact.

Note: For freestanding installation, it requires 30mm gap between both sides

for the beverage cooler as well as the rear, which allows the proper air

circulation to cool the compressor and condenser. Even for built-in installation,

it requires 10mm space on each side and at the top. The air vent at the front

must never be covered or blocked in any way.

*Levelling your beverage cooler

Beverage cooler must be levelled before loading your beverages. Your

beverage cooler is equipped with 4 adjustable feet to facilitate easy levelling.

Euro Appliances recommends that you tighten the back feet to the maximum

and adjust the front feet to create a level.

1-15

*Products & Specifications

EBC600SX

*Operating your beverage cooler

1) Turning on your beverage cooler. Plug in and switch on the beverage cooler

by pressing on the power button for a few seconds. When you use the

beverage cooler for the first time (or restart the beverage cooler after having it

power off for a long time), there will be a few degrees variance between the

temperature you have selected and the one indicated on the LED readout.

This is normal and it is due to the length of the activation time. Once the

beverage cooler is running for a few hours everything will stabilize.

Important: If the unit is unplugged, power is lost or turned off, wait 3 or 5

minutes before restarting the unit. The beverage cooler might not start if you

attempt to restart before this time delay.

Type

Single Temperature Zone

Item Number

EBC600SX

Bottle Capacity
Dimension (W*D*H)

595*595*798mm

Weight

48KG

Refrigerant

R600a/45g

Cooling System

Compressor Cooling

Ambient Temp

60-90 ºC

Temperature Range

ºC

Rated Voltage

220 - 240V

Rated Frequency

50HZ

Input Power