Euresys 1630 Coaxlink Mono, 1631 Coaxlink Duo, 1632 Coaxlink Quad, 1633 Coaxlink Quad G3, 1635 Coaxlink Quad G3 DF Installation Manual

Coaxlink

1630 Coaxlink Mono
1631 Coaxlink Duo
1632 Coaxlink Quad
1633 Coaxlink Quad G3

1635 Coaxlink Quad G3 DF
1637 Coaxlink Quad 3D-LLE
1638 Coaxlink Quad CXP-3

INSTALLATION GUIDE

© EURESYS s.a. 2018 - Document version 9.5.2011 built on 2018-02-16

1. Coaxlink PCIe Products Installation Guide

1.1. Disclaimer

EURESYS s.a. shall retain all property rights, title and interest of the documentation of the hardware and the software, and of
the trademarks of EURESYS s.a.

All the names of companies and products mentioned in the documentation may be the trademarks of their respective
owners.

The licensing, use, leasing, loaning, translation, reproduction, copying or modification of the hardware or the software,
brands or documentation of EURESYS s.a. contained in this book, is not allowed without prior notice.

EURESYS s.a. may modify the product specification orchange the information given in this documentation at any time, at its
discretion,and without prior notice.

EURESYS s.a. shall not be liable for any loss of or damage to revenues, profits, goodwill, data, information systems or other
special, incidental, indirect, consequential or punitive damages of any kind arising in connection with the use of the
hardware or the software of EURESYS s.a. or resulting of omissions or errors in this documentation.

1.2. Declarations

Notice for Europe

This product is in conformity with the Council Directive 2014/30/EU

This equipment has been tested and found to comply with Class B EN55022/CISPR22 and Class B EN55024/CISPR24.

This product has been tested in a typical class B compliant host system. It is assumed that this product will also achieve
compliance in any class B compliant unit.

To meet EC requirements, shielded cables must be used to connect a peripheral to the card.

Notice for USA

Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation or when
the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

▶ Reorient orrelocate the receiving antenna.

▶ Increase the separation between the equipment and receiver.

▶ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

▶ Consult the dealer or an experienced radio/TV technician for help.

Notice for Korea

The following products have been registered under the Clause 3, Article 58-2 of Radio Wave Acts:

Product KC Registration Number Product KC Registration Number

1632 Coaxlink Quad MSIP-REM-EUr-PC1632 1637 Coaxlink Quad 3D-LLE MSIP-REM-EUr-PC1637
1633 Coaxlink Quad G3 MSIP-REM-EUr-PC1633 1638 Coaxlink Quad CXP-3 MSIP-REM-EUr-PC1638

This product is in conformity with the European Union RoHS 2011/65/EU Directive, that stands for "the
restriction of the use of certain hazardous substances in electrical and electronic equipment".

According the European directive 2012/19/EU, the product must be disposed of separately from normal
household waste. It must be recycled according to the local regulations.

1.3. Precautions for Use of Board Products

Electrostatic Sensitive Device

Boards may be damaged by electrostatic discharges. Follow the procedure hereby described and apply any general
procedure aimed at reducing the risk associated with electrostatic discharge. Damage caused by improper handling is not
covered by the manufacturer's warranty.